Whats the T43p's vertical and horizontal refresh rates?

I am trying to install freeBSD and it asks me this.

Please make a Genius Appointment and take it in for service.

Similar Messages

Satellite A100-153: What are verical and horizontal refresh rates for my display

How can I found out what are verical and horizontal refresh rates for my display?

Hi
Do you mean the vertical and horizontal display resolution???
Anyway all informations should be listed in the user manual.
I dont know exactly what appendix is it but it must be placed somewhere at the end of the user manual.
Such infos are listed also in my user manual which was delivered and preinstalled on my Satellite notebook.

Apple 30 Inch Vertical Sync and Hoeiz Refresh Rates

I am trying to figure out the exact Vertical Sync and Horizontal Refresh Rates.
I have a dual boot setup with OS X and Ubuntu Linux on my G5 PpwerMac
I know that the Dell 30" is pretty close ( which I am using now ) but I don't want to damage my Display by using the wrong specs.
So If anyone knows the sync and refresh rates it would really be appreciated.

Here is a section from the 30" Cinema's EDID data that has the info you want:
Descriptor #1 is Timing definition:
Mode = 2560 x 1600 @ 60Hz
H. Active...............2560 pixels
H. Blanking.............160 pixels
V. Active...............1600 lines
V. Blanking.............46 lines
HSync Offset............48 pixels
HSync Pulse Width.......32 pixels
VSync Offset............3 lines
VSync Pulse Width.......6 lines
Pixel Clock.............268.00MHz
Horizontal freq.........98.53kHz
Vertical freq...........59.86Hz
H Image Size............641mm
V Image Size............401mm
H Border................0 pixels
V Border................0 lines
Non-Interlaced
Sync: Digital separate with
* Positive vertical polarity
* Negative horizontal polarity

HT4623 My iphone 5 seems to be stuck in the horizontal view when I'm in the message mode. In all other views I can turn the phone 90 degrees and horizontal to vertical works fine. Not sure what the problem is.

My iphone 5 seems to be stuck in the horizontal view when I'm in the message mode. In all other views I can turn the phone 90 degrees and horizontal to vertical works fine. Not sure what the problem is.

I found a solution!
Perhaps this is just temporary, but I have my display up and working again.
Although the symptoms are different were a bit different, the solution here worked:
http://apple.stackexchange.com/questions/120259/grey-screen-after-login-blue-scr een-of-death-from-cmdr
As I was able to connect to my HD via an external monitor, in the finder, I went to:
1. Macintosh HD --> System --> Library --> Extensions
2. From there I moved all of the files that started with ADM and ATI (19 in total for me) to a folder on my desktop. (You will need to enter your admin password for this)
3. Next was a restart.
4. Then my display started working again.
5. After that, I transferred the files back into my Extensions folder.
6. I then did another restart with my fingers crossed and breath held. It worked.
Also... During the last few days of trying to find a fix, I restored a Mavericks backup to my computer away from Yosemite.
I'm very sure this problem occurred when I put my MBP to sleep, disconnected the power in its sleep, while something was connected to a USB port and unplugging the USB device (for me an iPhone charger) while the MBP was closed.
I hope this helps the next person.

When I display the view-formula command , the information in the cell displays vertically and it is very hard to read. I want it to go back to the horizontal display I have had all along. Thanks

When I display the view-formula command , the information in the cell displays vertically and it is very hard to read. I want it to go back to the horizontal display I have had all along. Thanks

Allan:
Sorry, I forgot to mention that I am working with Excel for Mac.

Why are some of my pages centering themselves (vertically and horizontally) after I select the "Shrink document to avoid overwriting..." option under Add Headers and Footers?

I'm working in Adobe Acrobat X Pro. I added header and footers through Adobe. I needed to select the "Shrink document to avoid overwriting the document's text and graphics" feature under the "Appearance Options..." option within the "Add Header and Footer" window. Some of the pages in my document that only had a few lines of text on them centered themselves (vertically and horizontally). How can I prevent that from happening?

Just to recap, this is a collection of ports I have collected over time for people who needed this information when setting up the HP ePrint app so that they could view their email from within the app. I am certain other applications also need this information. Although lengthy, I could not find a more comprehensive place to retrieve this information. Feel free to post additional information, faulty information, or other related topics below as this is simply a collection of data and it would be practically impossible to test all of them. Thank you!
Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
When a solution is found please mark the post that solves your issue.
Every problem has a solution!

Center all vertically and horizontally?

I'm trying to self-publish a book using CreatSpace on Amazon. They want an extra 1/8" around all margins of a 6x9" book (actually more on the width) to allow for bleed. I have to generate a PDF. When I changed the page size it kept the type in the same spot, and made the pages jump back and forth a little in the PDF. It would be good if they stayed in the same place. How can I center ALL the artwork -- including the headers on the master page -- both vertically and horizontally to fill a particular page size? Thanks for any advice.

There may be a bit of miscommunication going on. You should be designing with the final trimmed page size in mind, and if you have images or solids that need to bleed, they need to extend beyond the trim size. When output to PDF, you specify whether to include crops and bleeds, and the size of the crop marks and bleed area. For example, if you want something like this crappy example I just knocked off:
You would set up your page size at 6x9 and place the images like this:
…and when output to PDF with the marks of your choice:
…you get something like this:
…which results in a PDF whose size is 6.83x9.83, but when trimmed will be 6x9. If you measure from the crop marks, the size is 6x9, and if you measure from the bleed marks, the size is 6.25x9.25, which is the trim size with 1/8" bleeds on all sides. Ask the publisher what marks they would like. They may not want bleed guides or color bars, so just give them what they want.

A library on my hard drive became corrupted, so I over-wrote it from an external hard drive. When I access the library now on my hard drive, many of the images are vertical, and cannot be rotated other than one at a time. Ideas to correct this?

A library on my hard drive became corrupted, so I over-wrote it from an external hard drive. When I now access the library on my hard drive, many of the images are vertical, and cannot be rotated other than one at a time. Ideas to correct this?

You had already done "Repair" and "Rebuild"? These usually takes scores of minutes or hours.
Does the Library on your external drive work from the external drive? Navigate to it in Finder and double-click the name.
If it does, delete the problem Library, empty the System Trash, reboot, Verify your system disk using Disk Utility (and might as well repair permissions while you're at it), reboot, test the external drive Library once more to confirm it works properly, then close it and copy the Library to your system drive. When the copying is done, double-click the Library (now on the system drive) and see what you get.

HP LaserJet 5500dtn print quality issues: vertical and horizontal streaks

Hi,
I am getting large vertical yellow streaks, accompanied by cyan and magenta vertical dashes on each print. Also, each page has vertical and horizontal black streaks. I've cleaned the fuser and that hasn't made much of a difference. I've also tried cleaning some of the cartridges, which didn't help. The internal roller of each cartridge continues to get covered with excess toner. Furthermore, I get a weird offset of some of the text (a faded version of the text that is offset about 1.5" from the regular text). Is there anyway to fix this issue by cleaning certain parts? Any other suggestions? Thanks

Hi,
Yes it is in Warranty. It is virtually brand new.
After I last posted I got through to the online chat support and was sent an email with options to 'troubleshoot' which I had already done with no success.
I was also given a link to try to update the printer firmware - which I will try when I get home from work.
I will see if that makes any difference but am sceptical as the printer worked fine the first time round but hasn't worked since and nothing has changed on it.
Chris.

Word document pdf printing with vertical and horizontal pages

I have a Word document that has both vertical and horizontal formatted pages. When I print to PDF, the I get a new pdf file whenever a page orientation change is found. pages 1 to 7 are vertical, 8 to 12 are horizontal and 13 to 20 are vertical again. If I print to a file named "out_to_PDF" I get 3 files named "out_to_PDF", "out_to_PDF2" and "out_to_PDF3", the first one with pages 1 to 7, the second one with pages 8 to 12 and the third one with the remaining pages. Is there a way to get only one file with all the pages?
I know I can merge the files later. This file with 20 pages is no problem. I have several 70+ page docs, with multiple changes between horizontal and vertical that will result in 20 or more separate pdf files.
Any pointers?

Word renders print jobs that change the orientation as separate print jobs. So, each print job becomes its own PDF.
You can make an Automator workflow to combine PDFs. I’m not sure how it decides the order it combines them, so you’d have to experiment.
This is built as an Application where you’d drop all of the PDFs onto the App icon and it will open the combined PDF where you can edit, name, and save.

Quick Look PDF with vertical and horizontal pages

Is there any way to make Quick Look preview a PDF file with vertical and horizontal pages without adding white padding and retaining the aspect ratio?
Now, if I have a PDF with page 1 vertical and the other pages horizontal QL shows the latter also with the ratio of a vertical page and adds white padding at their top and bottom. You get the inverse output if the first page is horizontally oriented, but the rest are vertical.

Word renders print jobs that change the orientation as separate print jobs. So, each print job becomes its own PDF.
You can make an Automator workflow to combine PDFs. I’m not sure how it decides the order it combines them, so you’d have to experiment.
This is built as an Application where you’d drop all of the PDFs onto the App icon and it will open the combined PDF where you can edit, name, and save.

Center text in text field - vertically and horizontally

Hi to all,
I have a text field with a specific size (for example 10x10 cm) I need this size because all the fields in the report must have this minimum size and they just can grow vertically (expand).
But i need to put the text centered in the field, vertically and horizontally. just in the middle whatever the size of the box.
The parameter "Center" in justify text doesn't help. Only adjust horizontally.
Thanks in advance.
Filipe Almeida

Hello,
If you want to center vertically, you have to use an anchor .
Regards

Center vertically and horizontally with a single layout?

verticalLayout has the horizontalAlign property, and horizontalLayout has the verticalAlign property. How can you use a particular layout to determine the flow of the children, but also specify vertical and horizontal alignment? In Flex 3 this was as simple as <VBox verticalAlign="middle" horizontalAlign="center">...

Take a look at http://forums.adobe.com/thread/448063
If you don't want to use extra containers then you could use Spacer components.
For example to align vertically in the center:
<s:VGroup width="200" height="200" horizontalAlign="center>
<mx:Spacer height="100%" />
<s:Button label="center aligned" />
<mx:Spacer height="100%" />
</s:VGroup>
Or at the bottom:
<s:VGroup width="200" height="200" horizontalAlign="center>
<mx:Spacer height="100%" />
<s:Button label="center aligned" />
</s:VGroup>

Iphone 5 rotates between vertical and horizontal modes, but does not flip vertically.

New Iphone 5 rotates between vertical and horizontal modes, but does not flip vertically.
Tried restarting, checked the lock, gyroscope.

Hey Oprion,
Thanks for the question and congrats on your new iPhone 5c. The orientation of your iPhone will depend on the application you are using. For example, most of the built in applications only support the three main orientations (Horizontal, Vertical, Horizontal), whereas the Voice Memo’s application will operate “upside down” for easier access to the microphone.
Change the screen orientation - iPhone
http://help.apple.com/iphone/7/#/iph3badf94ec
Thanks,
Matt M.

My new air 2 iPad will not rotate the screen from vertical to horizontal

MMy new iPad Air 2 will not rotate the screen from vertical to horizontal. Is there a screen lock

There is a screen lock. If the Rotation Lock is on you will see a circular arrow surrounding a small lock at the top of your screen near the battery level indicator. To turn on or off the Rotation Lock swipe up from the very bottom of the screen to being up the Control Center. Look for that same icon and tap it.

Whats the T43p's vertical and horizontal refresh rates?

Similar Messages

Maybe you are looking for