When change channels audio stuck in loop

Starting yesterday when I change channels on the HD FIOS box- the channels change immediately as usual but the last sentence of the channel audio previous channel loops and repeats for about 7-8 seconds. Once it stops, the audio on the new channel is out of sync. If I change channels again- it corrects iteself. I can usually change about 3-4 more channels and evertything is normal, however it will start up again. This is not a picture problem- just audio as descrived above.
I have unplugged the HDMI- the cable from the wall to the unit- and uplugged the power to the HD unit yesterday (did not matter) and today (Did not matter). Could the HD box need to be replaced? I have an HD DVR downstairs and there is no problem on that system down stairs.
Thanks

Not sure if this will help, but did you try going into the DVR customer support menus and selecting the item called Fix Common STB/DVR issues? This can correct a lot of audio & video issues on a DVR. You will have to hunt for this menu item since Verizon for some reason keeps moving it around and renaming it every few months. It will take 5 - 10 minutes to run and will reboot your DVR (perhaps a couple of times).
I don't recommend pulling the plug on a Verizon DVR since you will likely cause more damage to the DVR hard drive. The Verizon DVR is always recording your current channel even when it is in screensaver mode. When you pull the plug, it may cause the recording head on the hard drive to become damaged or damage the recording surface since the drive head is not properly parked when it loses power. At best you will corrupt the filesystem on the hard drive. Try the Fix Common DVR Issues app a couple of times before pulling the plug. Pulling the plug should be the absolute last resort.

Similar Messages

Popping sound soundbar when changing channels

I recently purchased a soundbar to go with my HDTV set. Experience popping when changing channels or when changing settings in the DVR. Manufacturer of the soundbar says that I must match the STB (Motorola 7232) audio settings with the TV's which is Force or LPCM and turn off Dolby Digital. However, I cannot find these settings.
Take the soundbar out of the mix and the TV does not experience any popping. This tells me that this cannot be the STB but the manufacturer says it is. Any help with audio on FiOS TV would be greatly appreciated.
Solved!
Go to Solution.

Let us know if you find the menu. The tricky thing is that you have to power it off from the front display and then do ok menu using the remote. It took ne a couple times to get there with the new box. Best of luck.

Hanging when changing channels

I am currently on release 1.9 build 10.95. Ever since the software was "upgraded" I have noticed the following:
Intermittently, when changing channels, by selecting from the guide, often the system will hang, for up to a minute, before the channel finally changes, almost as if it is waiting for something to time out.
Intermittently, when I use the remote, the green light will flash on the box showing that a signal has been received, but nothing happens. I may have to issue the command two or three times.
This has happened on all three of our DVR's - Motorola QIP - 7216 1
I have reset the box via software, physically reset the box by pulling the power chord, and put new batteries into the remote, numerous times, and the problem persists.
Is it only me, or has this problem been reported under a different heading?

Usually, you can turn off a video setting and it speeds up the responce time of the set top box. Try hitting menu - settings - video settings - sd override and selecting off. There are other settings in there but they dont seem to affect the responce time much.

Can't set the correct key when converting imported audio to GB loops

Hi,
I feel I am really out of options for this one. I am trying to convert a couple of mp3 files to useful GarageBand loops. This is what I tried first:
1) drag the mp3 file on the timeline.
2) using a steady 4-beat, match the BPM settings to that it fits the tempo of the imported file
3) check the key of the imported file with a software instrument, and switch the project's key accordingly
4) Edit -> Add to Loop Library
Using this method, the produced loops show up in the Loops Browser correctly, but they play back in the wrong key. Example: I created a loop from a mp3 file that was originally played in A. I tagged it as being in the "A" key by creating a loop from it, with the project key set to "A".
When it then shows up in the Loop Browser, and I would select this loop with my Garageband project (still) set to "A" - I would expect to hear the loop being played in its original key.
It doesn't. It plays about four or five semitones too high (the difference between A and C, or C and E)
I haven't been able yet to figure out why this is so, or if there is any pattern in how much the key is off.
Then I searched far & wide, and found the Apple Loop Utility and a couple of articles on bulletsandbones.com. I also checked the midi import settings, though I doubt whether they have any influence here. They were set at 44.1 KHz.
This is what I tried then:
1) use bulletsandbones.com's never-fail conversion to AIF format (44.1 KHz sample rate, 16 bit)
2) use the Apple Loop Utility to "tag" the AIF file, setting it so that it shows up in the right category of the loop browser, etc.
3) also, use this utility to tag it with the key that the loop is played in
4) copy the AIF file into the Loop Library directory
5) start Garageband, and refresh / re-index the Loop Library so that the new loop is added and properly indexed
This made no difference. Or maybe it did, but the loops thus produced STILL do not play back in the key that I tagged them in (if I set the project accordingly, of course). It's completely mystifying.
I can omit a key indicator in the Apple Loop Utility, and only then does the loop play back as it should. But then it does not change with the project's key settings anymore.
Even more strange: even a loop that I tagged (in the "A" key) and saved with the Apple Loop Utility, plays back too high in that same Apple Loop Utility when I re-open it. It does play back correctly in Finder's Fast Preview.
I could not find any mention of this problem elsewhere. Does anyone have a suggestion what might cause this?

I think this is the culprit:
3) check the key of the imported file with a software instrument, and switch the project's key accordingly
If the "follow tempo & pitch" box is checked, this might change the sample's pitch and throw GB off.
Try to determine the sample's key before you import it, set the GB project's key accordingly, and then import the sample. That should assign it the correct key!

Pixels when changing channels

Received new replacement black box this week, all fine so far (shock horror!), apart from when I flick channels, the pictures pixelate for about 5 seconds, which is quite annoying. The new broadband channels dont do this. Any suggestions? Cheers!

Hi Ggmcintosh,
The only time I have experienced the problem you mentioned is on the channel where my reception hasn't been great. You could try Rescanning your channels to see if this makes a difference.
Thanks
Paddy
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

42TL515U blacks out when changing channels in different formats

This television is getting annoying. Unlike our previous television, a Samsung, whenever I switch from a program from a non HD channel stored on the DVR to a live HD broadcast the Toshiba frequently seems to "get confused" with the format switch and the screen goes black. Sometimes I have to reboot by turning it off and on and then wait 40 seconds for it to power on and go to the HD station. This was an expensive purchase - at least for our budget - but I am very disappointed. In retrospect, I probably should have bought another Samsung or the Vizio.
John

Usually, you can turn off a video setting and it speeds up the responce time of the set top box. Try hitting menu - settings - video settings - sd override and selecting off. There are other settings in there but they dont seem to affect the responce time much.

Flex sampling frequency changes when I use it with apple loops

Flex sampling frequency changes when I use it with apple loops in a 24 bit 88.2 project

sorry !
Flex changes sampling frequency when I use it with apple loops in a 24 bit 88.2 project

Airplay audio streaming from Iphone to ATV crashes when changing randomly title?

Why does airplay audio streaming from Iphone 4S iOS 7.04 crashes when changing randomly title? The ATV is not connected to a TV, only to an AV Receiver. Anywhere the same problem?
Thx a lot
Nolame

Oops - I messed up the title-
This is with iOS 7.0.2 and Apple TV 6.0.

When adjusting the audio volume in a selected region, why does it give me a curved line instead of straight and why cant I change it like i can with a fade in our out?

When adjusting the audio volume in a selected region, why does it give me a curved line as a transition instead of straight, and why cant I change the fade shape like i can with a fade in our out? When I slide thet volume all the way down it makes a very abrupt down curve. It's audibly noticdible.
Thank you.

Use the range selection tool and select the portion of the clip you want to change the volume on. Drag the volume line down and FCP will create keyframes which you can adjust as you want to get a fade shape.

Audio changed channels!

For some reason my Premeire Pro is putting the audio from imported video files in Audio 7 and 8 where is used to put the video audio in audio 1. I am importing from the swame Canon XA10 as I always have in the past. I also cannot move the audio to any other channel.
Any ideas wold be appreciated becausse I sure can;t find what changed!

What we need to know is what is the channel-count of the Tracks, where PrPro will not allow you to place the Audio, and what the channel-count of those Source Files are.
If, for instance, your Audio Track 1 thru 6 are Mono (1-channel), and your Source Files are Stereo (2-channel), they will need to go onto a 2-channel Audio Track. You can look at the little "speaker" icons in the Audio Tracks' Header - 1 speaker = Mono (1-channel), where 2 speakers = Stereo (2-channel), and a little "5.1" = 5.1 (6-channel) Audo.
If one has, say 4 2-channel Audio Tracks (2 speakers in the icon), and 1-channel Mono Source Material, they cannot place those Clips onto those 2-channel Audio Tracks. If one were to drag one to the Master Track (you cannot add Audio Clips to that Track), then PrPro will create the necessary Mono 1-channel Audio Track, numbered with the next available Audio Track Number.
Good luck,
Hunt

How to change channel on 5GHz on new (2012) Airport Express when connecting to en excsiting network?

Airport Express only provides channel 100 automatically when configuring it to connect to an excisting wireless network at 5GHz. This is out of range for most routers, which typicaly provieds channels 36 through 48 for connecting 5GHz devices.Only when you configure the Airport Express to establish a new wireless network it allows you to change channels manually. This is really weird. I have severeal Airport Express units (older model) around my house for streaming music, and they work just fine on 2.4 GHz, and so does the new (2012) one, but I bought it specifically to use 5GHz in a corner of my house with interference from surrounding 2.4 GHz networks, so I am really disappointed with this product. There should and must be a way to connect it to an excisting 5GHz network, but how to get the channel right in this cnfiguration mode?

When you extend wireless you cannot switch channels.. The Express is locked to the channel used by the Extreme.. there is no choice about this.
Reboot the extreme .. wait a minute and then reboot the express.. Channels will be tested on reboot to pick the best.. there is nothing much else you can do.

What is the default setting for amount of seconds between songs when burning an audio cd? I changed mine and my cds are all messed up!

What is the default setting for number of seconds between songs when burning an audio cd? (I changed mine and my cds are messed up!) Thanks!

What is the default setting for number of seconds between songs when burning an audio cd? (I changed mine and my cds are messed up!) Thanks!

After effects crashing when changing audio input

Hi all,
I've been trying to get my Steinberg (Yamaha) ur-28m external USB audio interface/soundcard to work with After Effects CS6 for a week now. The problem is that everytime I change the audio input in the AE preferences to the Steinberg asio drivers AE freezes for a few seconds and then crashes. Same thing happens in Premiere btw.
I've tried everything possible:
- updated Steinberg drivers to newest version
- updated AE to latest version
- trashed preferences
- totally removed and installed master collection again
- formatted hd and Reinstalled windows 7 and installed Master collection again.
- tried all possibles buffer rates
Problem still there...
I looked into the events log and it mentions ntdll.dll and makes afterfx.exe crash.
Bottom line is I can't work with sound now, which is really frustrating. In other programs (non Adobe) these drivers are rock solid.
Apparantly After effects (and in my case premiere also) doesn't like Steinberg. I saw this other thread about Steinberg in After Effects: http://forums.adobe.com/thread/1063355.
Doesn't look like it's been solved.
Main specs of my pc:
Intel i7-2600
16GB ram Corsair
Nvidia gtx 560 ti
Gigabyte Z68P-DS3 motherboard
Seagate 1TB (7200rpm)
Anybody some ideas? Thanks!!

Basically what I did was set it as the line out for sound from windows, so
all sounds will be routed through the UR22 (Will work with any program).
You can leave it set as is to have windows sounds play out of the computer
line/speaker out and go into the sound settings in Premiere and set the
audio playback device as the UR22 (Only Premiere plays out of UR22) but
that is where i had problems. I just set all audio playback in windows to
route to the UR22 (Line Out in windows) and left settings in Premiere alone
(In Playback settings leave audio device as Adobe Desktop Audio....Premiere
routes to windows output, which i set to UR22) and everything worked fine.
I am a video editor and spend 95% of my time in Premiere and some time in
Audition and After Effects and it has worked great.The only issue I have
had with the UR22 is that every once in a while if i leave my system on
over night rendering and playback something the next morning any audio will
sound like it is playing back too slow (Pitch shifted lower). But all you
have to do is unplug the usb and plug it back in and all is well again.
Hope this helps. Good luck.

How do I change the audio sample rate from 48kHz to 44.1kHz for Mpeg2

Hey all,
I've been searching for a while but haven't found any direct answers in the forums or the user manual so here goes.
I have to dispatch a file to Bloomberg TV and the file specs they have given me are as follows:
Video Standard: MPEG-2, MP:ML, 4:2:0
Frame Rate: PAL 25fps
Video Size 720 x 405
Aspect Ratio 16:9
Audio Standard MPEG-1 Layer 2
MPEG-2 Program Stream Mux rate 6mbs per second
Bit Rate Type: CBR
Video Bit Rate 5.7mbs
Audio Bit Rate 192kbs
Audio Sample Rate 44.1Khz
Interlacing: Upper Field first (why they want interlaced for web streaming is beyond me)
GOP Structure: IBBP
I-Frame distance 12
Now everything above is fine except the audio encoding because even though I have set up a new setting from scratch I cant find anywhere to adjust the audio sample rate. The Inspector tells me the Audio encoder is set to:
Format: MPEG
Sample Rate: 48.000kHz
Channels: 2
Bits Per Sample: 16
Anyone Know how or even if I can change these audio settings? The only adjustments I can find are the filters or the transport/program stream option. I have it set to program as specified by Bloomberg.
Thanks in advance
J

The only setting that I could find in compressor that lets your change the bitrate to 44.1 is when you create a new dolby digital setting and then under the inspectors audio tab/Target System button, change the button to Generic AC-3. When done, you can change the Sample Rate to 44.1.
Hope this helps?

Video tracks disappear when changing between sequences in premiere CS6

Dear people, can you please help me find out why video tracks disappear when changing between sequences in premiere CS6.
All it shows is the audio track and it is maximized to the first frame of the sequence. Video tracks are there but hidden - although video IS showing up in the program monitor.
When I pull the tracks down in the timeline window using the dividing line between the video and audio tracks and set the sequence work area back it works fine, however it is a great annoyance having to do this every time when i swap between sequences.
Can anybody please suggest a solution to this?
I'd appreciate any help.
MD

This is the audio tracks problem i cannot overcome:
https://forums.adobe.com/thread/1586025
(basically every type of audio i drop/place onto the timeline becomes left channel only, regardless of it being music or camera-recorded audio.
In the source monitor everything plays back just fine, but when placed to the timeline - it becomes LEFT only.
Weird.... (or am I and not it)

When change channels audio stuck in loop

Similar Messages

Maybe you are looking for