When i lock my Iphone4 it will only turn back on when i reset it, by pressing home and on/off at the same time.

When my phone is locked it won't react to the home or on/off button. It's not doing it all the time but it happened 3 times in 2 days, what is happening?

Hello there, xmiK.
The following Knowledge Base article offers up some great steps for troubleshooting button issues on your iOS device:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Sleep/Wake button won't lock or unlock iPhone
To lock the phone, press the Sleep/Wake button. Note: By default, if you don't touch the screen for a minute, iPhone locks automatically.
To unlock iPhone, press the Home button or the Sleep/Wake button, then slide the slider.
If either of the above steps don't work, try turning iPhone off and then on again.
If the iPhone will not power off, reset it.
Try to lock or unlock the phone.
My issue is still not resolved. What do I do next?
Contact Apple Support.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Similar Messages

  • HT201263 I could not reach itunes just pushing home button.  I had to push home and wake/sleep at the same time. in recovery now, not sure if this will work and not happy with messed up ipad

    not sure which operating system i am using.  whatever because it messed up my ipad.  Try to follow directions from forum about connecting to store and being in recovery mode.  I was not able to connect just using the home button,  had to use home button and sleep/wake button at the same time.  finally recovering my ipad, but very unhappy that updates messed it up.  If updates are not any good, don't put them out there.

    Most likely Digitizer of Front Screen is broken or its Connector to the Logic Board has come loose. You could try a Restore with iTunes on computer. Fix is press connector back to Logic Board. Or, replace entire Front Screen Assembly. Or, take to Apple, if Genius decides it needs Out of Warranty Replacement it is $149 at the Apple Store for iPhone 4.

  • IS there a way to load and purchase different photos from iPhoto and ship them at the same time? the only way that I can find is to purchase each photo (or multiple of one) at a time, which increases the cost of shipping, as I want to get one print of 20

    Is there a way to order multiple different prints in any quantity from Iphoto? it appears currently like I would have to ship each separately, even if only one print... is there a way around this so I can can get several DIFFERENT prints of any quantity and ship all at the same time?

    Sure - easiest way is to make an album for photos you want to order and drag photos to it - when it is complete open the album, select all and order
    LN

  • My iPhone 4s will not sync a changed playlist from itunes unless i turn off music match. Shouldn't I be able to use a playlist and music match at the same time?

    my iPhone 4s will not sync a changed playlist from itunes unless i turn off music match. Shouldn't I be able to use a playlist and music match at the same time?

    It's not entirely impossible actually as someone has pointed out to me that I can turn on Call Forwarding and that stops any incoming calls. I've just forwarded it to my google voice number and then turned on "do not disturb" in google voice and whenever I get a call it goes straight to my google voice voicemail and my phone does nothing. The only thing now is I still get text messages but I think the phone calls bugged me more because they would make my music turn off for much longer.
    Even though this isn't a perfect solution it's something so far so maybe you shouldn't just come out and say there's NOTHING I can do because so far I've found part of a solution. If you don't have anyting productive to say then just don't reply and close the tab. Thanks.
    At this point I'm wondering if anyone knows of any Jailbreak tweaks that can enable what I want. Unless of course it's agaisnt the rules of this forum to mention jailbreak stuff...

  • My iphone 4 locked up for several hours. i then tried to reset by holding down the home button and power button at the same time for 10 seconds and then the home button for 10 seconds. it is now completely black. what do i do? couldnt restore it in iTunes

    My iphone 4 locked up for several hours. i then tried to reset by holding down the home button and power button at the same time for 10 seconds and then the home button for 10 seconds. it is now completely black. what do i do? couldnt restore it in iTunes. Has anyone had this problem? Help!

    Same thing happened to me today. I wasn't even using the phone for the past 6 hours and suddenly I can't connect to the internet, none of my internet apps would work - nothing. I tried to call AT&T from the iphone and it locked up - couldn't turn it off, change to the home screen - nada - brick.
    Did the Home/Power button thing and that worked but this I've only had this phone for about 4 weeks and it's locked up more times than my 3GS did the whole two years I had it! Ridiculous

  • Using iPad 2 - if i use the slide switch to lock rotation, i cannot unlock rotation, unless i use it to mute sounds.  i can't therefore have unmuted sounds and unlocked rotation at the same time??

    using iPad 2 - if i use the slide switch to lock rotation, i cannot unlock rotation, unless i use it to mute sounds.  i can't therefore have unmuted sounds and unlocked rotation at the same time??

    Uh .... Yes you can. You just have to understand how the whole thing works.
    System sounds can be muted and controlled two different ways. The screen lock rotation can be controlled in the same manner as well.
    Settings>General>Use Side Switch to: Mute System sounds. If this option is selected, the switch on the side of the iPad above the volume rocker will mute system sounds.
    If you choose Lock Screen Rotation, then the switch locks the screen. If the screen is locked, you will see a lock icon in the upper right corner next to the battery indicator gauge.
    If you have the side switch set to lock screen rotation then the system sound control is in the task bar. Double tap the home button and in the task bar at the bottom, swipe all the way to the right. The speaker icon is all the way to the left. Tap on it and system sounds will return.
    If you have the side switch set to mute system sounds, then the screen lock rotation can be accessed via the task bar in the same manner as described above.
    This support article from Apple explains how the side switch works.
    http://support.apple.com/kb/HT4085

  • HT4085 So does this mean that I cannot have rotation lock off and the mute function off at the same time? In other words, can I have my screen rotate automatically as I hold my iPad in either portrait or landscape AND hear sounds from my apps at the same

    So does this mean that I cannot have rotation lock off and the mute function off at the same time? In other words, can I have my screen rotate automatically as I hold my iPad in either portrait or landscape AND hear sounds from my apps at the same time?

    In other words, can I have my screen rotate automatically as I hold my iPad in either portrait or landscape AND hear sounds from my apps at the same time?
    Yes, you can. You can configure the Side Switch (above the volume button) either as Mute switch or Rotation lock.
    Settings > General > Use Side Switch to: choose what you like the Side Switch to function as.

  • How can I do to acquire and save date in the same time and in the same file when I run continual my VI without interrupti​on.

    I've attached a VI that I am using to acquire amplitude from Spectrum analyzerse. I tried to connect amplitude ouput to the VI Write Characters To File.vi and Write to Spreadsheet File.vi. Unfortunately when I run continual this VI without interruption, labview ask me many time to enter a new file name to save a new value.
    So, How can I do to aquire and save date in the same time and in the same file when I run continual my VI for example during 10 min.
    Thank you in advance.
    Regards,
    Attachments:
    HP8563E_Query_Amplitude.vi ‏37 KB

    Hi,
    Your VI does work perfectly. Unfortunately this not what I want to do. I've made error in my last comment. I am so sorry for this.
    So I explain to you again what I want to do exactly. I want to acquire amplitude along road by my vehicle. I want to use wheel signal coming from vehicle to measure distance along road. Then I acquire 1 amplitude each 60 inches from spectrum analyzer.
    I acquire from PC parallel port a coded wheel signal coming from vehicle (each period of the signal corresponds to 12 Inches). Figure attached shows the numeric signal coming from vehicle, and the corresponding values “120” and “88” that I can read from In Port vi.
    So I want to acquire 1 time amplitude from spectrum analyser each 5
    period of the signal that I am acquiring from parallel port.
    So fist I have to find how can I count the number of period from reading the values “120” and “88” that I am acquiring from In Port (I don’t know the way to count a number of period from reading values “120” and “88”).
    Here is a new algorithm.
    1) i=0 (counter: number of period)
    2) I read value from In Port
    3) If I acquire a period
    i= i+1 (another period)
    4) If i is multiple of 5 (If I read 5 period)
    acquire 1 time amplitude and write to the same
    file this amplitude and the corresponding distance
    Distance = 12*i). Remember each period of signal
    Corresponds to 12 Inches).i has to take these
    values: 5,10,15,20,25,35,40,45,50,55,60............
    5) Back to 2 if not stop.
    Thank you very much for helping me.
    Regards,
    Attachments:
    Acquire_Amplitude_00.vi ‏59 KB
    Figure_Algorithm.doc ‏26 KB

  • My ipod has a black screen.  I have tried to hold the sleep/off button and menu button at the same time with no luck.   I connected to my computer and tried restore on itunes -  still with a black screen a voice said "screen locked'  code 542

    My ipod has a black screen.  I have tried to hold the sleep/off button and menu button at the same time with no luck.   I connected to my computer and tried restore on itunes -  still with a black screen a voice said "screen locked'  code 542

    Is the iPad charged?  Plug it in with the charger/wall outlet for half an hour and try again to reboot by holding both the power and home buttons until the apple logo appears.

  • HT1550 I'm having trouble with importing them into iTunes and converting them at the same time. when i hold down option over the files i can't find where its supposed to say create new version. is this if you're in iTunes?

    I'm having trouble with importing them into iTunes and converting them at the same time. when i hold down option over the files i can't find where its supposed to say create new version. is this if you're in iTunes?

    You can't do it in one step. Add to iTunes first, Once the tracks are in iTunes you may convert to a different format.
    tt2

  • When will the iPad be able to walk and chew gum at the same time?

    Granted yes I know it would chew up a ton of battery power, but will there be a time when the OS will allow you to say listen to something off of the iPod or a video app and say read a book or surf the web at the same time?

    You can already listen to music and surf the web/read simultaneously.
    Play something from the iPod app and it will continue playing when your using safari/iBooks etc.
    Double clicking the home button while doing so brings up the controls for the music.

  • My iPod 5 screen is black the camera will make the clicking sound when pushing the home button and sleep button at the same time but the s teen stays black !! I hope someone can help

    I have an iPod 5.  The screen is black, I tried charging it.  It makes a bing when I plug it in so power is going to it.  When I hold the sleep button and home button to use the camera it takes a pic although the screen stays black the sound is there.  I hope someone can help me !!!

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup. See:                                 
    iOS: How to back up           
    - Restore to factory settings/new iOS device.
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar          

  • HT4085 Having sound on and orientation lock off at the same time...

    When I go into the settings and change the slide switch to lock rotaion it so I can change the orientation and have the sound on. Yet when I do this the sound automatically turns off. how can I have one off and the other on at the same time?

    You can read my explanation as to how this works. See the part about the task bar at the bottom of the iPad.
    If you lose sounds for keyboard clicks, games or other apps, email notifications and other notifications, system sounds may have been muted.
    System sounds can be muted and controlled two different ways. The screen lock rotation can be controlled in the same manner as well.
    Settings>General>Use Side Switch to: Mute System sounds. If this option is selected, the switch on the side of the iPad above the volume rocker will mute system sounds.
    If you choose Lock Screen Rotation, then the switch locks the screen. If the screen is locked, you will see a lock icon in the upper right corner next to the battery indicator gauge.
    If you have the side switch set to lock screen rotation then the system sound control is in the task bar. Double tap the home button and in the task bar at the bottom, swipe all the way to the right. The speaker icon is all the way to the left. Tap on it and system sounds will return.
    If you have the side switch set to mute system sounds, then the screen lock rotation can be accessed via the task bar in the same manner as described above.
    This support article from Apple explains how the side switch works.
    http://support.apple.com/kb/HT4085

  • Problem when calling the RFC and IDoc adapter at the same time

    Hi,
    I'm having a major slowdown problem with XI3.0 SP11.
    When I'm sending a message(IDoc) from R/3 into XI to get translated into an EDI document, I have no problems and it's very fast.  RFC calls are very fast too.
    Now, if I'm sending the same message and at the same time another call is done trough the RFC adapter, then the full XI environment hangs for several minutes.
    I did all recommended settings from the XI-SR1 install guide(Configuring the J2EE Engine) and tuning guide (XI Configuration Parameters)
    and I don't know what to do more?   At the Unix level, command TOP shows that dw.sap.XDV_DVEBMGS70 is taking all the CPU% available when both messages(IDoc and RFC) are sent to XI at the same time.
    Anybody have an idea what to do next?
    Rgds,
    Yves

    Did you check the dev_rfc logs ? Also check SM21 for any errors. Logon to the Target System and check SM50 transaction then you will know whats going on.
    regards
    Shravan

  • How can u have lock rotation off and mute feature off at the same time

    How can u have lock rotation off and mute feature off at the same time

    Maybe this will help. The link at the bottom is the same one that was posted above.
    System sounds can be muted and controlled two different ways. The screen lock rotation can be controlled in the same manner as well.
    Settings>General>Use Side Switch to: Mute System sounds. If this option is selected, the switch on the side of the iPad above the volume rocker will mute system sounds.
    If you choose Lock Screen Rotation, then the switch locks the screen. If the screen is locked, you will see a lock icon in the upper right corner next to the battery indicator gauge.
    If you have the side switch set to lock screen rotation then the system sound control is in the task bar. Double tap the home button and in the task bar at the bottom, swipe all the way to the right. The speaker icon is all the way to the left. Tap on it and system sounds will return.
    If you have the side switch set to mute system sounds, then the screen lock rotation can be accessed via the task bar in the same manner as described above.
    This support article from Apple explains how the side switch works.
    http://support.apple.com/kb/HT4085

Maybe you are looking for

  • Can't add four specific albums to library off of external hard drive

    For some reason after my last sync quite a few songs on my iPod were no longer playing. It would show that they were on the iPod, but they would not play and would simply skip straight to the next song even if the iPod was paused when that song was o

  • How to install and use endnote?

    I have a problem using endnote in pages in order ti insert bibliografic references. I purchased pages from the app store and in the resources web page i was able to notice that i had to download and install it, so i did but it didnt work furthermore

  • Partial Transfer of Assets

    Hi,    We are trying to transfer LVA assets to another asset account. The assets doesn't have no values in 01 depreciation area and having balances in tax and local depreciation area.    While using the t.code ABUMN , and entered the value in the amo

  • CS6 Software won't open

    I had recently bought a used macbook on ebay, and the seller claimed it came with CS6 software. He send an activation code and serial number with the laptop. It was fine for about 2 months. Adobe application manager would open when I would open any o

  • First Twitter, now even Twidget is crapping out

    So yeah... I posted befor eI was having issues with Twitter force closing on me, and now it seems that Twidget is having it's own issues as well. It stopped refreshing and when I closed and opened it again, it kept saying my username/password was wro