When i press sleep wake button to turn on my iphone 3gs all i get is a white screen
trying to open the phone to make a call or answer the phone when i press the sleep wake button all i get is a white screen and cant do anything with the phone constantly turning phone on/off eventually my home page does return anyone know why and what to do.. thanks to all
MacBook Air Mid 2012?
"Apple has determined that certain 64GB and 128GB flash storage drives used in the previous generation of MacBook Air systems may fail. These systems were sold between June 2012 through June 2013."
http://www.apple.com/support/macbookair-flashdrive/
Similar Messages
-
When i turn on my macbook air, all i get is a white screen.
Have tried both types of resets i've found on the internet and in the owners manual. should i just take it to the apple store or is there something i can do? I have an older generation macbook air.
Go step by step and test.
http://support.apple.com/kb/ts1440
Startup Manager to select Startup disk.
http://support.apple.com/kb/HT1310
Repair Disk
Steps 2 through 8
http://support.apple.com/kb/PH5836
Reset PRAM.
http://support.apple.com/kb/PH4405
Reinstall OS X
http://support.apple.com/kb/PH10763?viewlocale=en_US
If this does not help, contact Apple. -
My Ipod touch is acting very annoying. When i press the sleep/wake button to turn it on it just turns on with the apple logo and stays there. The screen will then blink white occasionally and the process will start again. Once when it turned white. i pressed the power and home buttons at the same time and then the above process continued.
Sounds like your iPhones software may be corrupt. Try placing the iPhone into recovery mode. To do this, follow the steps in this article:
http://support.apple.com/kb/HT1808
Hope this helps
- Greg -
HT1430 MY IPHONE 4 WILL NOT RESTART WHEN I PRESS SLEEP/WAKE BUTTOM
I press sleep - wake button and it will not start
Then try a reset. Hold the sleep/wake and home buttons together until you see the Apple logo and then release. This should reboot the phone.
-
My 1st generation Ipod touch won't turn on at all and whenever I press the buttons to reset it all I get is a white screen, or a white screen with black lines across.Help pleaseeeeee!
You can work through the five 5 R's of troubleshooting to rule out the possibility of corrupted software.
http://www.apple.com/support/ipod/five_rs/
It might also be a good idea to let the iPod's battery fully drain. Then charge it back up and restore it once more in iTunes.
Otherwise, it's likely a hardware issue with the iPod's LCD display, meaning you'll need to take or send your iPod in for service either via Apple or a third party repair service. Here is Apple's repair pricing.
http://www.apple.com/support/ipod/service/prices/
Note that they don't actually repair the device, but exchange it for one of the same generation, model, and capacity. A third party service will actually replace the damaged part for a little less. Google "iPod screen repair" and you should get a number of results to work with.
B-rock -
when i active my mac pro all i get is a white screen and it loading and when it fully load its turn off , and it keep on doing the same thing for hours
Hi Shahenaz,
It's a little difficult to understand exactly what's going on with your mac based on the description you gave. Is there anything else you could add? Is it stuck in a reboot loop? Or is it just showing a white screen forever?
I had pretty much the same problem a few days ago, and was worried my mac was screwed permanently, but I got it fixed up no problem!
Follow these steps to try and troubleshoot/fix the problem.
1. Boot into OSX Recovery Mode
First, turn off your Mac. If it isn't responding, or is stuck in a reboot loop, just hold down the power button until it turns off, and you hear the fans stop. Then boot it while holding the Command and R keys. If it successfully boots into OSX Recovery Mode, continue with this step. If not, skip to step two. (My Mac couldn't successfully boot into the recovery mode, so I had to go to step 2)
Select "Disk Utility" from the list of options, and find your built in hard drive from the list on the left. Usually there are two listings/names for your drive. The first should be something like "500GB longchainoflettersnumbers Media". Then the one below will be a little easier on the eyes, named Macintosh HD, if you haven't changed its name. That's the one you want, click it.
Now go to the "First Aid" tab. Click on the "Verify Disk" button in the bottom right corner, and let it do its thing. Once that's done, hit repair disk, also in the bottom right corner. If your disk is corrupted, you may need to run the repair process several times, before it comes up completely clean.
Once this is done, select Shut Down from the Apple menu and, once your Mac is completely off, turn it back on like normal. If it works, great. If not, proceed to step two.
2. SafeBoot
Sometimes, when a mac is acting up and doesn't want to start, all it takes is a safe boot, followed by a regular restart. Or maybe you recently installed a program that either has malicious or errored coding that's causing your troubles. This is where Safe Boot comes in.
Turn off your mac, and reboot it while holding Shift. (If you want to see the process that's going on in the background, boot while holding Shift, Command, and V. This will enter something called Verbose Mode).
If it boots successfully into Safe Mode, great. If you believe that there's a particular program that you recently downloaded that might be causing your trouble, now's the time to delete it. If not, just reboot normally and see if it works! If it doesn't, or if your Mac didn't even Safe Boot like mine, proceed to step 3.
3. Fsck!
For this step, you're going to be booting your mac into Single User Mode. I'm not going to go into details as to what this step does, but it works for some people. Here are the steps.
Turn off your mac, and reboot it while holding Command and S. The screen should go black, and you'll see some white text run across the screen, wait a few seconds, until you see the command prompt. Now type
fsck -fy
and hit the Enter key. This will run a series of system checks, which could take a few minutes. Be patient on this part. Once it's done, it will show one of two messages:
1. "The volume (your Mac) appears to be OK
or
2. "File System Was Modified"
If you got message 1, type reboot and press Return. Hopefully your computer works after this - if not, proceed to step 4.
If you got message 2, run the same command again until you get message 1. If it doesn't seem to be working, turn off your system and proceed to step 4.
If you couldn't even boot into Single User Mode in the first place (like me), go to step 4 anyways.
Step 4: Reset the NVRAM
The NVRAM is another kind of RAM that stores data like the computer volume you had set before you turned it off, or the screen brightness, resolution etc. This memory is saved, unlike with regular RAM. Resetting it isn't harmful to your system, it will just put your screen brightness, volume, etc. to defaults.
Turn off your Mac, and reboot while holding Command, Option, P, and R, and continue holding them down until you hear the computer restart again.
I can't really explain why to do this step, I just know it works for some people, and seems to be what unbricked my MacBook Pro. If none of these steps, fixed your Mac, well the situation is looking pretty grim. Try setting up a meeting with a Mac Genius at your local Apple store. However, I know that many other people with these symptoms ended up having a logic board failure. Apple can swap out your logic board for a new one, but the price is pretty hefty, somewhere around $300 I believe.
Well I wish you luck, I hope this helped you! -
When i turn my touch all i get is a white screen help
when i turn on my touch all i get is a white screen help
Try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. From iTunes, select the iPad and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad.
There's more to try but let's go a bit at a time. -
HT201412 when turned on all I get is a white screen
My Ipod when turned on all I get is a white screen. I tryed to do a reboot w/power and home button and nothing
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Just updated to lion and my cctv access has stopped functioning all I get is a white screen in the middle of the control panel where the camera shots should be. I think it is caused by JAVA but am confused as when i view on snow leopard it works can you help
Open "Java Preferences" either from spotlight or your utilities folder...it's probably going to say you need to install a java runtime. Then just click install!
-
I messed up badly by trying to restore my brand new macbook pro by doing restart then command R and choose disc utility repair now when I start ,all I get is the white screen with a folder and a question mark,What can I do???help please
Can you still boot to the Recovery partition using Command and R whilst booting? Or did you wipe the Recovery partition as well?
If your Recovery partition is still intact, you can simply boot to it and reinstall the OS via the Internet. If you wiped the Recovery partition, you can hold down Command, option and R keys whilst booting and boot into true Internet Recovery mode. You'll be able to reformat the hard drive, erasing all partitions (format it as "Mac OS Extended (Journaled)" with a dingle GUID partition) and then reinstall the OS that shipped with your machine.
Note that you should use a physical Ethernet connection when restoring over the Internet - it's three times slower if you use wifi.
Try your Recovery partition first and if that doesn't work, use Internet Recovery.
Clinton -
****,I have done this successful in the past but on my IPad it shows I have 4 apps that need to be updated so when I hit the update tab all I get is a white screen. When I hit the purchase or other tabs it opens up. What could be the problem?
There have been numerous reports on the forum today regarding this issue. It seems to be an issue at Apple, but no information has been posted on the status site.
http://www.apple.com/support/systemstatus/ -
My sleep wake button won't work on iPhone 4
When USB not connected phones displays symbol that tells me to connect. When connected it shows that phone is charging but it won't charge. Sleep wake button unresponsive.
Sounds like a hardware problem.
Make an appointment at an Apple Store if there is one nearby to confirm. -
this happened when i was updating it from ios 5.0.1 to 5.1 i had to stop it before it was done updating and now all i get is a frozen screen.
- Try a reset:
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Then connect to computer and try to restore via iTunes.
- If screen remains on (white, has lines etc), let the battery fully drain. After charging for an hour try the reset and restore as necessary. -
When I try to access my iTunes Store from my iPhone 5 it opens with a blank white screen. Help!
I've tried for several days to open my iTunes Store on my iPhone. Every time it opens, but with a blank white screen.
Hi Upswife,
When troubleshooting iTunes Store connection issues, the following articles provide the best information:
First, try signing out of your account in Settings > iTunes & App Store. Once signed out, go ahead and sign back in.
iOS: Changing the signed-in iTunes Store Apple ID account
http://support.apple.com/kb/HT1311
If the above did not resolve your issue, refer to the following:
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
If you haven't been able to connect to the iTunes Store:
- Make sure that your iOS software is up to date by connecting your iOS device to iTunes and clicking on Check for Update in your device's Summary page in iTunes.
- Check and verify that you are in range of a Wi-Fi router or base station. If you are on a 3G capable device, make sure that cellular data is turned on from Settings > General > Cellular.
- Check to make sure you have an active internet connection. You can check the User Guide for your device for help with connecting to the internet.
- Check to make sure other devices (portable computers, for example) are able to connect to the Wi-Fi network and access the internet.
- Try resetting (turning off and then on again) your Wi-Fi router
- If the issue still persists see, iOS: Troubleshooting Wi-Fi networks and connectionsoriOS: Troubleshooting Wi-Fi networks and connections.
Thanks,
Matt M. -
Hi I was wondering if anyone has experienced probs with the ios7 on iphone 4s, as mine keeps going white screen and wont turn on reboot unless im lucky. When, if it comes on it blurrs and fades out after a couple of minutes the screen also jitters and dies often. I dont know if this is due to the software update or a faulty screen etc... any thoughts?
Sno problems here at all.
Maybe you are looking for
-
JDeveloper Team - Refers: How do I display multiple rows in a gridControl
JDeveloper Team With reference to the previous reply.. My query is not based on a view object. It uses the executeRetrieval command to do the select statement. The query obtains the correct number of rows but it displays only the first record out of
-
Itunes WONT start! can anyone please help???
i have tried reinstalling and a few other things but still when i try to start itunes a box comes up saying: "itunes cannot run because it has detected a problem with your audio configuration" any help would be greatly appreciated! thanks in advance!
-
ITunes upgrade causing MSVCR80.dll missing? What is Apple doing about this?
Yesterday I downloaded the upgrade to iTunes and that is the last time that I have been able to open it. All I get is that MSVCR80.dll is missing So I uninstalled and reinstalled and now it still has the error message and it is not openable. I hear t
-
I am trying to get ColdFusion to use our Frutiger Roman fonts which are in a PFM format. The windows 2003 server sees them fine and the fonts work in all windows software on the server but they do not show up when publishing a PDF from cfdocument. An
-
I have had people ask me to make a short 30 clip for the web say of some of there sporting shots, what is the best way to go about knowing what kind of compression you use and what type of file is best.