When i record i can barely hear anything and the input meter is barely reaching -34db even when the gain on my interface is turned all the way up on my interface

this issues is really getting to me. its works perfectly fine when am recording on ableton but on logic the input is so low :/

a
as u can see i have used the same setup for years no problem till a week ago :/

Similar Messages

  • I Can't montitor my voice when i record nor can i hear anything from the speakers when i press playback. Someone help me!

    I tried everything. I checked my input and output systems. My microphone works as well as my speakers. However, as soon as I try to record or playback a recording no sound is heard through the speakers! What gives?! What's the point of have tech if you can't use it!!!!!

    You need to set up your audio hardware preferences.
    Go to Edit/Preferences/Audio Hardware and make sure that your "Default Input Device" is set to be your microphone and the "Default Output Device" is set to be the sound card/speakers on your computer.
    However, this is where the limitation of using USB mics and onboard sound cards shows up--using a "proper" sound card and XLR microphone would allow you to set up a headphone or speaker mix in the interface itself.  Using a USB mic and built in sound card means your audio will have to do a round trip through your computer for you to monitor on your speakers or headphones--this will introduce some latency/delay.  To set up this sort of round trip monitoring, do your recording in the Audition Multitrack view and click on the the little "I" button (next to the "R" record arm button) on the track header.  This lets you monitor the input to that track and feed it back to your speakers or headphones.

  • My iphone 5 ATT, i can hear the recording, but can not hear anything from neither ear speaker or loud speaker when i call? what is the problem? what can i do, it is out of warranty.

    My iphone 5 ATT, i can hear the recording, but can not hear anything from neither ear speaker or loud speaker when i call? what is the problem? what can i do, it is out of warranty.

    1357b wrote:
    My iphone 5 ATT, i can hear the recording
    What recording?
    but can not hear anything from neither ear speaker or loud speaker when i call?
    You just wrote you could hear the recording...
    You can take it into an Apple store and have it checked out.

  • When trying to make calls the timer starts counting as if i am connected but i can't hear anything and my speaker button has turned blue

    when trying to make calls the timer starts counting as if i am connected but i can't hear anything and my speaker button has turned blue

    Did you use the latest backup after setting it up "as new device"? If yes, try again, this time without using the backup, maybe it contains damaged data causing your problem.
    If this does not bring any change, you should get it serviced.

  • I have an ipod touch 4th genereation and have problems when i record you can barley hear the voices and sounds recording i don't know what the problem is?

    i have an ipod touch 4th genereation and have problems when i record you can barley hear the voices and sounds recording i don't know what the problem is?

    sounds like ur ipod's mic is blocked with something check the back on the ipod near the back camera

  • While calling, I can't hear anything and the others cannot hear me. If record my voice everything works, but while calling no way. Someone can help me?

    It's so strange. Everything works, apps, connection, camera, video, voice recording...
    Only whrn I try to make a call nothing happens. My iphone rings, I answer...and no voice...
    I can't hear and no one can hear me...
    What could have happened to my iphone?
    What can I do?
    Thanks

    I've already tried hard reset....
    Nothing changed.
    I've just made backup, now I just have to click the "restore" button?
    It will reinstall evrything on my iphone or maybe I'll lost something?
    (sorry for my english! ^_^ )

  • Hello apple I have the problem with my iPhone and my friends have this problem too. My iPhone have the problem about calling and answer the call. When I use my iPhone to call I can't hear anything from my iPhone but the person that I call can answer it bu

    Hello apple
    I have the problem with my iPhone and my friends have this problem too.
    My iPhone have the problem about calling and answer the call. When I use my iPhone to call I can't hear anything from my iPhone but the person that I call can answer it but when answer both of us can't hear anything and when I put my iPhone to my face the screen is still on and when I quit the phone application and open it again it will automatic call my recent call. And when my friends call me my iPhone didn't show anything even the missed call I'm only know that I missed the call from messages from carrier. Please check these problem I restored my iPhone for 4 time now in this week. I lived in Hatyai, Songkhla,Thailand and many people in my city have this problem.
    Who have this problem??

    Apple isnt here. this is a user based forum for technical questions. The solution is to restart, reset, and restore as new which is in the manual after that get it replaced for hard ware failure. if your within your one year warranty its replaced if it is out of the warranty then it is 199$

  • How come the volume of other programs are lowered while one FaceTime? I exchange media with friends and colleagues and I can barely hear anything. There should be a way we can manually control the volume of different programs

    How come the volume of other programs are lowered while one FaceTime? I exchange media with friends and colleagues and I can barely hear anything. There should be a way we can manually control the volume of different programs

    I own the movies and I want them to stay in my iTunes library basically forever.
    But in both cases the file name no longer shows in the movie list, so I don't know how to re-download it from the Cloud.
    iTunes prefs > Store > Show iTunes in the Cloud purchases.
    This will show all your iTunes purchases in your library with a cloud icon down arrow. Click the icon to redownload or click on Play to stream without downloading.
    Also see this , -> Download past purchases
    and techncially, you don't "own" the movie, You simply have a license to use it.
    Yet the first thing iTunes does when you hit the delete key is tell you that it will remove the movie forever from all devices and the library.
    Actually, no it does not tell you that.
    FYI: You should keep copies of all yoru iTnue spurahses as the labels/movie studios/copyright owners can pull their product at anytime and it won't be available to redownload.
    Suggestions here -> http://www.apple.com/feedback/

  • I connect my mic with an M-audio mobile pre usb device.  When I try to record, I can see that my voice is recording but can't hear it during playback.

    I connect my mic with an M-audio mobile pre usb device.  When I try to record, I can see that my voice is recording but can't hear it during playback.  I tried different input and output settings but it didn't help.  Any help will be appreciated.

    Hear your microphone or instrument as you play and record (monitoring)
    You can hear, or monitor, input from an instrument or microphone in GarageBand while you play and record. When you turn on monitoring for a track, you hear the musical instrument or microphone connected to the track’s input. Monitoring lets you hear yourself play so that you can hear the part you want to record as well as the rest of the project.
    You can turn on monitoring for a Real Instrument track or Electric Guitartrack from the track’s header, or in the Track Info pane. Electric Guitar tracks always show their monitoring buttons, and you can show monitoring buttons for Real Instrument tracks using a menu command. You can use monitoring with feedback protection to avoid feedback while you play.
    Hide
    To turn on monitoring in the track header:
    Choose Track > “Show Monitoring for Real Instrument Tracks.”Monitor buttons appear in the headers of Real Instrument tracks. On tracks with monitoring turned on, the button lights yellow.
    Click the Monitor button in the header of the track you want to use.
    HideTo turn on monitoring in the Track Info pane:
    Double-click the header of the Real Instrument or Electric Guitar track you want to turn on monitoring for.The Track Info pane opens.
    From the Monitor pop-up menu, choose one of the following:
    Choose Off to turn off monitoring. You can hear your instrument only while you record.
    Choose On to turn on monitoring and protect against feedback.
    Choose On (no feedback protection) to turn on monitoring without feedback protection. If the input level is too high, it may cause feedback (especially if you are using a microphone and listening to your project through your computer speakers).
    For an Electric Guitar track, you can view the Monitor pop-up menu by clicking Edit, and then clicking the back side of the amp. The Monitor pop-up menu appears with the input controls below the stage.
    You should usually turn off monitoring when you are not playing or singing. When monitoring is turned on, your computer can pick up output from your speakers or monitors, causing unwanted feedback. Using headphones rather than speakers to listen to your projects can help eliminate feedback.
    If you select your computer’s built-in microphone as the audio input, in the Audio/MIDI pane of GarageBand preferences, monitoring is turned off for all Electric Guitar tracks to avoid unwanted noise.
    SEE ALSO
    If you don’t hear sound from a Real Instrument 
    Was this page helpful?Send feedback.
    © 2010 Apple Inc. All rights reserved.

  • I can't hear anything when making calls no dailing tone or anything but when I try and audioface time it works fine please help

    I can't hear anything when making calls no dailing tone or anything but when I try and audioface time it works fine please help

    Hi Nfrith1,
    Please take a look at the article referenced below, the same as in my original reply.  The receiver on the iPhone does not have anything to do with the speakers on the bottom of the phone nor your microphone.
    Clear the receiver
    The iPhone receiver won't work properly if it's blocked or dirty. Here's where the receiver is:
    Follow these steps, testing after each:
    Make sure nothing is blocking the receiver, such as a case or film.
    If you have a new iPhone, remove the plastic film on the front and back of the device.
    Check the receiver opening to see if it's blocked or dirty. If necessary, clean the receiver opening with a clean, small, dry, soft-bristled brush.
    While you're on a call, turn on speakerphone. If you still can't hear, then your network or reception could be the issue. Try calling again later or from a different location.
    Restart and update
    Restart your iPhone and test again.
    If there's still no sound or poor sound quality, update to the latest version of iOS.
    Get more help
    If you've tried these steps and there's still no sound or poor sound quality from your iPhone, contact Apple Support.
    Learn what to do if other people can't hear you on a call.
    If you can't hear a person on a call or voicemail or if the sound quality is poor on iPhone
    Take care,
    Alex H.

  • When I make a call, I can't hear anything but my correspondants can hear me. Can anyone help?

    When I make a call, I reach my corresponddents (who can hear me) but I can't hear anything. Can anyone help?

    I would first try contacting your carrier, see if its something with their network. If thats all good then you can try restarting, resetting, and even restoring your phone to see if that helps.
    If all else fails then I would recommend going in to an Apple Store to see if this could be a potential hardware issue with your phone.

  • When I click on a video on FB that takes me to YouTube, I can't hear anything on my phone.  I am up to date on software.  Any suggestions?

    WWhen accessing a music video on FB that takes me to YouTube, I can't hear anything.  I am up to date on software.  How do I fix this?

    Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
    *Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
    *Do NOT click the Reset button on the Safe Mode start window
    *https://support.mozilla.org/kb/Safe+Mode
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes
    Do a malware check with several malware scanning programs on the Windows computer.
    Please scan with all programs because each program detects different malware.
    All these programs have free versions.
    Make sure that you update each program to get the latest version of their databases before doing a scan.
    *Malwarebytes' Anti-Malware:<br>http://www.malwarebytes.org/mbam.php
    *AdwCleaner:<br>http://www.bleepingcomputer.com/download/adwcleaner/<br>http://www.softpedia.com/get/Antivirus/Removal-Tools/AdwCleaner.shtml
    *SuperAntispyware:<br>http://www.superantispyware.com/
    *Microsoft Safety Scanner:<br>http://www.microsoft.com/security/scanner/en-us/default.aspx
    *Windows Defender:<br>http://windows.microsoft.com/en-us/windows/using-defender
    *Spybot Search & Destroy:<br>http://www.safer-networking.org/en/index.html
    *Kasperky Free Security Scan:<br>http://www.kaspersky.com/security-scan
    You can also do a check for a rootkit infection with TDSSKiller.
    *Anti-rootkit utility TDSSKiller:<br>http://support.kaspersky.com/5350?el=88446
    See also:
    *"Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked

  • Hi All.  My iPad 4 just started having issues with the volume.  On either Bluetooth or the iPad Speaker, anything I'm watching or listening to drops the sound to just barely hearing it and then, about 2 seconds later, it comes back.

    Hi All,
    I tried to search through the community, but with the sheer volume of posts, I didn't find anything that seemed like the same issue.
    My iPad 4 just started having issues with the volume.  On either Bluetooth or the iPad Speaker, anything I'm watching or listening to drops the sound to just barely hearing it and then, about 2 seconds later, it comes back.
    I haven't tried wired ear phones, but I am sure they'll be the same way.
    It's very random, but consistent enough to happen several times per day.
    Thanks for any help that anyone can provide.
    I have restarted it and also did a Hard Reboot and it didn't help.
    Thanks Again,
    Scott P.

    Well there you go, when you advertise it just be sure to say that you can't even see the scratches at half brightness and see how it goes.
    Of course you are saying you want $500 for one with many scratches on the screen, has been dropped, but the scratches aren't visible at half brightness, and has no warranty. Or I can buy a refurbished iPad 4 WiFi 32 GB directly from Apple with no scratches and a one year warranty for $499. http://store.apple.com/us/product/FD514LL/A/refurbished-ipad-with-retina-display -wi-fi-32gb-white-4th-generation
    Why would I buy yours?
    I wouldn't pay more than $300 for a used model with your specs in perfect condition. But yours is far from perfect. I think your high point is $250 which is why I said 50%.

  • I can't hear anything during a phone call

    This just randomly started up this morning, and the nearest Apple store is 2 hours away, so I'm turning here. I have an iPhone 4 (not the S) and the newest IOS. When someone calls me, my phone rings like normal, but when I answer, I can't hear them at all. I can make phone calls, but when I do, I can't hear the phone ringing before the person answers, and I still can't hear anything on the other line. I only know that the call went through because the screen says a call is in progress, and the people I've tested it on can hear me just fine.
    I've tried resetting my phone to factory settings, and I've turned it off and on multiple times. I don't know what else I can do. My phone is in good shape: a hairline crack in the screen, but it's just cosmetic. Nothing else is wrong. I hear all the alerts and everything else I'm supposed to hear, and I was able to have normal conversations as of last night. I dropped my phone early this morning from about 3 feet off the ground, but it's in an Otterbox and well protected. I am somewhat panicking that I can't talk to people, and I'm not eligible for an upgrade until July. Also, I did not purchase the extended Applecare plan.
    If someone could please help, I would really appreciate it. I'm planning on taking it to Best Buy once they open. I don't know if they can do anything, but I'm stuck.

    One more thing:
    I suspect that this problem is not related to the “headphones mode problem” because I have no problems with the laudspeaker.
    Maybe an HW issue?

  • ITunes 7.3.1 - I can't hear anything!

    I upgraded to the new version of iTunes the other day and since then, when I've tried to play a song, the counter still goes like the song is playing but I can't hear anything. I can still hear the sound effects on my computer and I tried playing a movie on QuickTime and the sound works on there fine so it must be iTunes.
    Anyone know what's going on?

    Some have solved the problem by starting Garage Band.

Maybe you are looking for

  • Mac Mini als externe Festplatte nutzen

    Want to buy a MacMini and want to connect it to my 27" imac as an external hard drive, is this possible? And wenn yes do I connect is with fire wire or thunderbolt?

  • Desktop Won't Stay Arranged (after upgrade to Tiger)

    I just upgraded from 10.3.9 to 10.4.10, and all is perfect except for the desktop arrangement. The old 10.3 desktop was 4 columns of 36x36 icons arranged as "keep arranged by type". The new 10.4 desktop (also "keep arranged by type") is 3 columns of

  • How do you add a gradient to a (bezier) stroke?

    I created a stroke with the bezier tool, just two points. I want to have a distinct gradient to the color but I can't figure out how to do it. I added the gradient colorize filter but it doesn't seem to do it. Any advice?

  • Roles of an SAP SD consultant

    Hi all, I am an Aspiring SAP SD Consultant who got a job recently.I got to know that I will be will be working on an IS-Utility Project in a Giant Infrastructure Service Provider Company..could you please help me in the kind of Roles and Responsibili

  • Design in flash or import png files

    Hi, I'm having someone help with the design of my site. He wants to give me png files for the graphics. Won't that increase the file size? Would it be better if he designed the graphics in flash instead of importing png files? Just wondering which wa