When I run csreource with -b option, I m receiving error
when I run csreource with -m option, I m receiving error. If I remove -b option, it works fine.
./csresource -b o=People, ou=test.calendar.com,o=cp -m [email protected] -c test create test123
Could not find calmaster
Unable to create resource calendar, aborting
Let me know what wrong I am doing. Calendar server is on Linux and Version is: 2005Q4
navvith wrote:
when I run csreource with -m option, I m receiving error. If I remove -b option, it works fine.
./csresource -b o=People, ou=test.calendar.com,o=cp -m [email protected] -c test create test123
Try the above command with quotes e.g.
./csresource -b "o=People,ou=test.calendar.com,o=cp" -m [email protected] -c test create test123Regards,
Shane.
Similar Messages
-
When i try to download 'Get album artwork' I receive error alert with (-609) I have tried to download the artwork on the advanced tab, but still no success. My computer runs Windows 7 and the alert appears in my itunes which on my computer.Can you assist?
Perhaps try the "Error -609" section in the Specific Conditions and Alert Messages: (Mac OS X / Windows) section of the following document:
iTunes: Advanced iTunes Store troubleshooting -
I am having trouble trying to boot from my lion osx install disk on a 2007 macbook. The disk ejects when I start up with the option key depressed. Anyone have any ideas?
Thank you.How did you get a Lion OSX install disc? They don't exist. Do you mean the gray disks that came with your 2007 MacBook?
If you mean the gray disks, try starting up with the "c" key held down.
What version of OSX is on your MacBook now? Have you tried booting from the Recovery partition? -
When I run ical on my mac I get the error:
The server responded with an error.
The request for account “Yahoo!” failed.
The server responded with
“504”
to operation CalDAVAccountRefreshQueueableOperation.
I hit "go online" and almost immediately I get the same message again. Any ideas?I am tired of how Yahoo has gotten worse and worse. It is the ONLY account I get problems with DAILY (even after removing and re-adding). AOL will act up once in a while not taking a saved password but accepting it when OK is clicked.... But Yahoo is always responding with such errors.... Today's calendar error is:
The request (CalDAVAccountRefreshQueueableOperation) for account “Yahoo” failed. -
When i run relink FND using adadmin, i got this error...
when i run relink FND using adadmin, i got this error...
Starting link of product 'pay' on Sun Nov 7 20:50:35 PKT 2004
Current product is pay
Current product TOP is $PAYTOP
Current prodarea is /home/oracle/opt/d01/oracle/prodappl/pay/11.5.0
Backing up or removing executables...
adrelink: error: program PYATUPD is not writable.
Please make sure that the Unix userid running this program has write
permissions on it, and that it is not in use. If the program PYATUPD
is in use, please make sure to terminate it before relinking
Oracle Applications.
adrelink is exiting with status 1
End of adrelink session
Date/time is Sun Nov 7 20:50:35 PKT 2004
You are running adrelink, version 115.82
Pl suggest
regrds,
Rizwanwhen i run relink on dbnode it compile successfully, but when i do same on apps node it give below error
Done with link of fnd executable 'flint60' on Thu Nov 4 18:12:59 PKT 201
Relink of module "flint60" failed.
See error messages above (also recorded in log file) for possible
reasons for the failure. Also, please check that the Unix userid
running adrelink has read, write, and execute permissions
on the directory /home/oracle/opt/d01/oracle/prodappl/fnd/11.5.0/bin,
and that there is sufficient space remaining on the disk partition
containing your Oracle Applications installation.
Done with link of product 'fnd' on Thu Nov 4 18:12:59 PKT 2010
adrelink is exiting with status 1
End of adrelink session
Date/time is Thu Nov 4 18:12:59 PKT 2010
Line-wrapping log file for readability ... -
Hi am trying to save Data into a write to measurement file vi using a NI PXI 1042Q and DAQ NI PXI-6229 with a real time mode but it is not working but when i run it without uploading it into the PXI it save in to the file please find attached my vi
Attachments:
PWMs.vi 130 KBother problem is that the channel DAQmx only works at real time mode not on stand alone vi using Labview 8.2 and Real time 8.2
-
I wish to convert my Matlab files into .dll's so that I can use them in LabVIEW. I am using 'mcc' and 'mbuild' of Matlab to convert my .m files into .c and .dll.
When I try to run the .dll's in LabVIEW, I get an error message in a modal window stating some required .dll or procedure is not found.
How should I resolve this issue. Should I add any other Matlab .dll's in course of making my .dll?
Please help in solving this issue... Thankyou very much.KJV wrote in message news:<[email protected]>...
> When I run the matlab generated dll, it is stating 'matllb.dll not
> found'. Is it that I should set the path for matlab\bin to include
> all the dll's before I compile? When I make dll from C, it works fine
> in LabVIEW. The problem is from .m to .dll. The problem also arises
> when I convert my .m to .exe. The same error of 'matllb.dll not
> found' comes over. Should I change my matlab compiler options or
> something else? Please help me?
I have the same question,I don't know how to use the matlab DLL file in labview,
I hope someone can descripe the procedure in detail. -
HT204406 when matching my music with ITunes store I keep getting error notification
when matching my music with ITunes store I keep getting the followig message after a while: "A problem caused program to stop working correctly. Windows will close the program and notify you if a solution is available. Could someone tell me how can I fix this problem.
It keeps disconnecting me and my music stops playing. Thank you
enriqueromanSince about Feb 1 2012 was having this same problem - seemingly started after I had downloaded latest iTunes and Lion updates. I got the error both when trying to update apps on iPhone 4S and MacBook Pro.
I found the solution on another discussion list. My iTunes account had an "&" in the name. I edited the account details through iTunes and this solved the problem immediately. -
When doing a restore with Time Capsule, I get -8003 error; restoring nothing
Hi,
When doing a full restore with Time Capsule, I get -8003 error; restoring nothing. This happens with all recent backups. Also after doing a verify/repair of the TimeCapsule disk.
This is a dissaster for my originals (my Ableton Live projects). I am very dissapointed in TC and TM at this moment, because I trusted my backup system in combination with my MBP fully.
Please help?
Best regards, TomHi Pondini,
Sorry for the late response, but the problem was something else and were two separate ones.
Somewhere along the way the TC backup couldn't find backup to the original TC volume, that's why I let TM backup towards my user volume named 'Tom'.
When I wanted to restore the root of my drive when selecting the diskname and 'Restore' in any point in time, this resulted in error -8003 in the activated TimeMachine.
Then I tried to do it via the recovery OS and even via the original OSX DVD. Both not enabling me to select the TC volume named 'Tom'. Then I remembered that I first backed-up onto the original 'TimeCapsule' volume/partition. When I copied the sparsefile to the 'TimeCapsule' partition, I was able to recover the entire disk using the recovery OS.
All my files are backup and I am a happy Mac user once again :-)
Thanks & Regards, Tom -
When syncing my ipdad with my laptop i get an error 13019.. what is it and how do i sort this
when syncing my ipad with my laptop i get error 13019 .. what is this eroor and how do i fix the same
do u know how to fix it yet?
-
When I run the Ipod Updater I get the message Error in service
My 5g Ipod is not recognized and when I run the updater it shows the message Error in Service. Please help
Not sure....Have you tried resetting the iPod and trying it again. Almost sounds like the software issue, but not totally sure. If you haven't tried resetting your iPod, try that and see what you get! If you don't know how to reset your iPod just press and hold the middle button and the menu button. Your iPod will turn off, and reboot
-
[Solved] Screen goes black when I run "xrandr" with displayport connec
I am running Arch on a Dell Latitude E6500 with Xorg, nouveau, and Gnome 3. The graphics chipset is identified by lspci as "01:00.0 VGA compatible controller: NVIDIA Corporation G98M [Quadro NVS 160M] (rev a1)". So far, everything has gone swimmingly with the integrated monitor. Today, I tried to connect an external monitor via DisplayPort. I initially connected the monitor with the system booted and logged in graphically. The external monitor did not receive a signal, so I ran xrandr in an xterm to see if it was being detected. As soon as I ran the command, the laptop screen went black. On a reboot (this time with the DisplayPort cable plugged in from the start), the boot process stopped at the end of the systemd messages (ie, the boot was successful, but X did not appear to start). Connecting to the system via ssh from another machine, I set DISPLAY=:0 and ran xrandr:
Screen 0: minimum 320 x 200, current 1280 x 800, maximum 8192 x 8192
LVDS-1 connected primary 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm
1280x800 60.03*+ 40.02
1024x768 59.92
800x600 59.86
640x480 59.38
720x400 59.55
640x400 59.95
640x350 59.77
VGA-1 disconnected (normal left inverted right x axis y axis)
DP-1 connected (normal left inverted right x axis y axis)
1920x1200 59.95 +
1600x1200 60.00
1280x1024 75.02 60.02
1152x864 75.00
1024x768 75.08 60.00
800x600 75.00 60.32
640x480 75.00 60.00
720x400 70.08
DP-2 disconnected (normal left inverted right x axis y axis)
So, X does appear to be running, but isn't actually rendering to either monitor. I noted that there is no "*" next to a graphics mode for DP-1, which I took to mean that no mode was selected.
I then ran "xrandr --output DP-1 --auto" in an attempt to wake up the monitor. This had no effect on either monitor (I still had the boot messages on the integrated monitor, and a blank screen on the external), but running xrandr again showed that the default 1920x1200 mode was selected:
Screen 0: minimum 320 x 200, current 3200 x 1200, maximum 8192 x 8192
LVDS-1 connected primary 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm
1280x800 60.03*+ 40.02
1024x768 59.92
800x600 59.86
640x480 59.38
720x400 59.55
640x400 59.95
640x350 59.77
VGA-1 disconnected (normal left inverted right x axis y axis)
DP-1 connected 1920x1200+1280+0 (normal left inverted right x axis y axis) 519mm x 320mm
1920x1200 59.95*+
1600x1200 60.00
1280x1024 75.02 60.02
1152x864 75.00
1024x768 75.08 60.00
800x600 75.00 60.32
640x480 75.00 60.00
720x400 70.08
DP-2 disconnected (normal left inverted right x axis y axis)
The Xorg log shows the monitor connected through DisplayPort being detected with nothing that immediately looks like an error:
[ 22.289] (II) NOUVEAU(0): EDID for output DP-1
[ 22.289] (II) NOUVEAU(0): Manufacturer: DEL Model: a02b Serial#: 842084435
[ 22.289] (II) NOUVEAU(0): Year: 2009 Week: 7
[ 22.289] (II) NOUVEAU(0): EDID Version: 1.4
[ 22.289] (II) NOUVEAU(0): Digital Display Input
[ 22.289] (II) NOUVEAU(0): 8 bits per channel
[ 22.289] (II) NOUVEAU(0): Digital interface is DisplayPort
[ 22.289] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 52 vert.: 32
[ 22.289] (II) NOUVEAU(0): Gamma: 2.20
[ 22.289] (II) NOUVEAU(0): DPMS capabilities: Off
[ 22.289] (II) NOUVEAU(0): Supported color encodings: RGB 4:4:4
[ 22.289] (II) NOUVEAU(0): First detailed timing is preferred mode
[ 22.289] (II) NOUVEAU(0): Preferred mode is native pixel format and refresh rate
[ 22.289] (II) NOUVEAU(0): redX: 0.674 redY: 0.319 greenX: 0.188 greenY: 0.706
[ 22.289] (II) NOUVEAU(0): blueX: 0.148 blueY: 0.064 whiteX: 0.313 whiteY: 0.329
[ 22.289] (II) NOUVEAU(0): Supported established timings:
[ 22.289] (II) NOUVEAU(0): 720x400@70Hz
[ 22.289] (II) NOUVEAU(0): 640x480@60Hz
[ 22.289] (II) NOUVEAU(0): 640x480@75Hz
[ 22.289] (II) NOUVEAU(0): 800x600@60Hz
[ 22.289] (II) NOUVEAU(0): 800x600@75Hz
[ 22.289] (II) NOUVEAU(0): 1024x768@60Hz
[ 22.289] (II) NOUVEAU(0): 1024x768@75Hz
[ 22.289] (II) NOUVEAU(0): 1280x1024@75Hz
[ 22.289] (II) NOUVEAU(0): Manufacturer's mask: 0
[ 22.289] (II) NOUVEAU(0): Supported standard timings:
[ 22.289] (II) NOUVEAU(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 22.289] (II) NOUVEAU(0): #1: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 22.289] (II) NOUVEAU(0): #2: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 22.289] (II) NOUVEAU(0): Supported detailed timing:
[ 22.289] (II) NOUVEAU(0): clock: 154.0 MHz Image Size: 519 x 320 mm
[ 22.289] (II) NOUVEAU(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0
[ 22.289] (II) NOUVEAU(0): v_active: 1200 v_sync: 1203 v_sync_end 1209 v_blanking: 1235 v_border: 0
[ 22.290] (II) NOUVEAU(0): Serial No: G283H929210S
[ 22.290] (II) NOUVEAU(0): Monitor name: DELL 2408WFP
[ 22.290] (II) NOUVEAU(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 22.290] (II) NOUVEAU(0): EDID (in hex):
[ 22.290] (II) NOUVEAU(0): 00ffffffffffff0010ac2ba053303132
[ 22.290] (II) NOUVEAU(0): 07130104a534207822b325ac5130b426
[ 22.290] (II) NOUVEAU(0): 105054a54b008180a940714f01010101
[ 22.290] (II) NOUVEAU(0): 010101010101283c80a070b023403020
[ 22.290] (II) NOUVEAU(0): 360007402100001a000000ff00473238
[ 22.290] (II) NOUVEAU(0): 3348393239323130530a000000fc0044
[ 22.290] (II) NOUVEAU(0): 454c4c20323430385746500a000000fd
[ 22.290] (II) NOUVEAU(0): 00384c1e5311010a2020202020200012
[ 22.290] (II) NOUVEAU(0): Printing probed modes for output DP-1
[ 22.290] (II) NOUVEAU(0): Modeline "1920x1200"x60.0 154.00 1920 1968 2000 2080 1200 1203 1209 1235 +hsync -vsync (74.0 kHz eP)
[ 22.290] (II) NOUVEAU(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 22.290] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
Googling has turned up a number of people having issues with DisplayPort, but in these cases the external monitor simply needs to be enabled (xrandr --auto, a BIOS setting, etc). Has anyone experienced this situation, where the working primary monitor stops working?
Thanks!
Last edited by Gavster (2015-01-25 17:00:50)I got a displayport -> HDMI cable to try the laptop with my television. This worked seamlessly, with X auto-detecting the new monitor and correctly enabling it with a default of 1920x1080 (interlaced). I also was able to change it to 1280x720 (progressive) with xrandr. Since the monitor I originally tried with straight displayport also has an HDMI input, I tried the new cable there and again was met with success. I'll mark this as solved with the likely culprit being something very strange with my displayport cable (I had ruled the cable out since the EDID was properly reporting the monitor model and supported resolutions).
-
Ostringstream 10; hangs when compiled and build with -mt option.
I've written a very simple program to test the use of the stl class ostringstream. The program write an integer to the ostringstream object. In a multithreaded environment (compiled and build with the -mt option), that operation hangs and never returns, whilst it works fine if the program is compiled and build without the -mt option.
Here is the program :
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <sstream>
int main() {
std::ostringstream buffer;
printf("before writing integer to ostringstream\n"); fflush(stdout);
buffer<< 10;
printf("after writing integer to ostringstream.\n"); fflush(stdout);
printf("exiting.\n"); fflush(stdout);
return 0;
Compilation and build :
CC -mt test.cpp -o test
Do you any idea why the program hangs at buffer << 10; in a multithreaded environment ?
(I have tried to write a string instead of a integer, then it works).
Thanks a lotHi, I've tried your code with Solaris 7 with Forte Developer 6.2, and it seems to work fine. I get the following output:
before writing integer to ostringstream
after writing integer to ostringstream.
exiting.
My compiler version is:
CC: Sun WorkShop 6 update 2 C++ 5.3 Patch 111685-03 2001/10/19
-Moazam -
I wanted to add a second DVR to my system. I was told about quantum. It is cool, but I decided a second DVR made the most sense for what I needed even though it cost a little more. At first I was told the cost of the second DVR then once I told the rep I wanted one he said it is. It available and I had to upgrade to Quantum.
I asked him straight up if that was true, he said yes.. I wanted to talk to someone else was told to call 1-800 number. What a mess that is.
Today we went to the local verizon fios equipment place (thankfully one is close) and got the second DVR.
I need to complain about this but I can't find anywhere to do so. They would not listen to what I wanted, but kept pushing the new service. Does anyone have a direct number or an email address to discuss this with them?angelapena2793-
In review of your account, we see that our Regional Executive Relations team is currently working on a resolution for you and has been trying to reach you. I have added this email communication to our records and I am forwarding the information to the Regional team. A representative will contact you as soon as possible. -
Occurs when running Edit.com for example. Error has choice to Close application or Ignore. If Ignore is chosen, application appears to run normally. Running repair of Windows 2000 does not correct the problem.
I'm glad you found it. Don't worry about the post. It's always good to check the KBs first, but we can't help it if we miss one sometime! The forum is definitely helpful though so don't feel hesitant to use it in the future. Good luck with the programming!
J.R. Allen
Maybe you are looking for
-
WIndows Connection to xserve from home
Hello, We are a school that is trying to connect to our server from our house on both mac and pc. Macs work fine but pcs don't. We have an apple xserve running 10.4 that is connected to our network with an outside ip address. If someone can help it w
-
Sybase expired password changed via JDBC ...
hi, please help me in this matter : i can't figure out how to change an already expired password via Sybase JDBC implementation ( jConnect ). i read the postings about Oracle having passed a custom value for this kind of change but i just don't seem
-
Problem with workflow manager after restore from dump
Hi, I updated my development environment from my dump production (restore full from dump). I restore my applicative schemas and aslo the schema owf_mgr which is used by my application. I've got a problem with three views that I cannot recompile.... W
-
Need SAP IS-Retail Training center and SAP certification material
Hi pls some one help on getting SAP IS-Retail Training center and SAP certification material. thanks Satish
-
I installed Oracle Linux 5.7. I need to view the .bash_profile file or whatever file Oracle Linux uses to store the environment variables for a user. I am working with the "oracle" user whose home directory is /home/oracle. Connected as "oracle" I is