When I take photos using my flash, the photos turn out dark?
I cant take photos with my flash because it will show as a black screen or a really dark image as if I did not use the flash. What could be the cause of this? Is there a way to fix it myself?
Morning, CherryRocket,
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Take a look at:
Camera
Camera is not functioning
Hope this helps,
Mario
Similar Messages
-
Everytime I take a picture using my flash, the picture comes out all foggy
Everytime I take a picture using my flash, it comes out foggy!! What can I do to stop this??
The better designers are taking this into account. People should look at the case they are about to purchase. If the case comes within about an 1/8 inch of the flash, it's apt to be a problem.
-
When i take a picture with flash the camera goes black
Whenever I try to take a picture with flash on my camera goes black.
There are two issues that come to mind... the first (hopefully it's this one) would be that you have a software issue that could be solved by restoring your iPhone from a back up...
The other would be that you have a hardware issue with the camera ... if the camera worked fien before you upgraded, then likely it's a corrupted software file that can be solved by doing the restore. -
when i take a picture with flash in a dark place , the photo appears with a blue line . how can i default this ? is this normal ???
You probably have a filter set for the normal camera mode but not the square.
To fix, in Photo mode, touch the filter icon (three circles) and select None for the filter. -
When I take pictures using the front camera the photo saves as if it were flipped in the opposite direct. How do I get it to saved as the picture was originally taken?
If you are talking about landscape pictures, hold the phone so the camera is at the top and the volume buttons on the bottom. If you hold it with the volume buttons on the top, the camera is upside down.
-
When I take photos of myself, the image come out backwards. I have an iPad2 and an iPad 3, and both of them do the same with my self portraits. Any ideas on how to fix this. I use wifi.
Gmabert-
The front camera displays a reversed image on the screen, as if you were looking into a mirror. When you take a picture, it comes out normal, which is backwards to what you would have observed on the screen.
Fred -
When I take photos now with my ipad 3 the photos do not go to the photostream folder...they go to the camera roll so they are not transferring to my pc although they were up till today. How can I fix this?
I went there and the problem might be because of low battery power..I am charging my ipad now and will let you know if that has helped...Thanks for the link..
-
On my iphone 4s, when I try to take a pic it flashes the pic for a second, but then the pic doesn't ever show up. It is assigned a number like a pic is there, but it is just a blank white space. When I try to share the pic, it shares the post with blank white in place of the pic.
See https://bugs.downthemall.net/ticket/2147
Google Search Bug
Reported by: openid:nathan wride Owned by:
Priority: major Milestone:
Component: Polish/Usability Version: 2.0.10
Keywords: Google search instant save bug Cc:
Operating System: Windows
Description
Hi Guys
I have found a bug/annoying thing that occurs frequently on google. When searching, DTA trys to download the search...
I'll try to attach a screenshot.
Attachments
[https://bugs.downthemall.net/attachment/ticket/2147/Screenshot.png Screenshot.png] Download (113.0 KB) - added by openid:nathan wride 4 weeks ago.
The screenshot that shows the bug. -
My iPhone has 34%of the power,but when I take photoes it will power off by itself!
First, update iTunes, then connect the phone to the computer and do a restore. This will also get your iOS up to date. Your phone should operate correctly after doing this, if not, you will most likely need to have the phone serviced or replaced.
-
i have I 4S 64 - worked fine not when i take a picture it flashes to camera roll then removes its self - cant find it any where -
Have you tried restarting or resetting your iPhone?
Restart: Press On/Off button until the Slide to Power Off slider appears, select Slide to Power Off and, after the iPhone shuts down, then press the On/Off button until the Apple logo appears.
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10 seconds). Ignore the "Slide to power off" -
When using my iMac the screen turned blue and so I turned the compute off. When I turn on again power does get to the computer but there are no chimes and the screen remains black. Any advise please. David
Hello DJJOC,
Thanks for using Apple Support Communities.
To start troubleshooting this issue where your iMac's screen will not illuminate, please reset your SMC by following the information outlined below.
Resetting the SMC for Mac Pro, Intel-based iMac, Intel-based Mac mini, or Intel-based Xserve
Shut down the computer.
Unplug the computer's power cord.
Wait fifteen seconds.
Attach the computer's power cord.
Wait five seconds, then press the power button to turn on the computer.
Note: For Intel-based Xserve computers that are not responding, you can shut down locally, or by using remote commands, or by pressing and holding the power button for five seconds.
Intel-based Macs: Resetting the System Management Controller (SMC) - Apple Support
Take care,
Alex H. -
When I take photos on my iPhone they end up on my My wife's iPad also. How do we stop that from happening?
You can do it from the iPad or from a computer, whichever is easiest:
Set up an Apple ID in iTunes - Apple Support
And then set up the iCloud account for that Apple ID:
Creating an iCloud account: Frequently Asked Questions - Apple Support
Any questions post back!
GB -
Why when I take photos with my iPad do only a few of them appear on my MacBook Pro?
I have noticed that when I take photos with my iPad only some of them transfer automatically to my MacBook Pro. Can anyone explain why this is happening please?
On the Mac open System Preferences > iCloud then click Options to the right of Photos.
Make sure: My Photo Stream is selected. -
I want a solution to this problem
Dear apple ,
I recharge iTunes Gift Card for $ 25 and when I want to use and download the application from the store asked me to answer the secret question, but unfortunately forgot to answer confidential questions I ask you to help me please
thank youClick here for information. If the option to have the answers emailed to you isn't available or doesn't work(the email may take a few hours to arrive), contact the iTunes Store staff via the link in the 'Additional Information' section of that article.
Nobody on these boards can reset them for you.
(92282) -
New computer win 8.1 pro, installed my creative Suite 4 Design premium but it shuts down when I try to use any of the programs and gives me an error code 147:20. How can I fix this? Is this a conflict with win 8.1 pro?
You need to adjust your security stuff/ permissions and possibly use compatibility modes. It means that your licensing service is being blocked/ shut down.
Mylenium
Maybe you are looking for
-
where we manintain COST OF PRODUCTION TYPE in SPRO.i want to change year in cost of production type
-
Can I upgrade to the new MacBook Pro from PowerBook copying the hard disk?
I have a Power Book G4 17", now I'm going to buy a new MacBook pro 17" and want to transfer the same software (I mean the whole content of my actual HD) to the new MacBook Pro using SuperDuper! I want to know if the Intel based MacBook Pro can run th
-
Inventory Process (LM50) with RF Device
Hello Gurus, I have a doubt with the functionality of RF Device when I execute Inventory by system-guided, in transaction code LM50, I have active the SU functionality, so when the system assign to me the inventory document, and I follow the next ste
-
AD password sync connector.
Hi, What are the pros and cons of AD password sync connector? can some tell those in details. Thanks
-
Why spfile is not being backedup auto? what need to be adjusted? Just want to clear my concepts. I have full, cumu & archlog & controlfile backups but no spfile, why RMAN> list backup of spfile; using target database control file instead of recovery