When I try to calibrate my iPod nano after a run it just shuts down and restarts. Whats happening?
After I run (iin basic mode) I try to calibrate. (I've done this a few times before).
Lately when I do/try this the iPod just shut down and restarts.
I've tried restoring the iPod in iTunes to no help.
It's a 6th generation nano coupled to a nike sensor.
Any help would be much apreciated.
As a test to determine if it is nike sensor only issue run once without the sensor. Use the inbuilt accelerometer to complete a run and calibrate it.
Similar Messages
-
Ipod camera function not working unless I shut down and Restart
Ipod Touch has problem opening the camera function. When I shut it down and restart it it works for a little while but eventually stops
Have you tried reset?
Restore? -
My iPad isn't working. I cannot follow a link in an email or connect to a game. It goes to a black screen then back to the main screen. Any idea what could be causing this?
Settings > General > Reset > Reset Network Settings
Perform a "hard reset" on the device by pressing down and holding the home button and the sleep/wake button for up to 30secs. until you see a black screen with the Apple logo, then release.
Then test to see if it solved the problem. -
what do i do when i try to open my ipod nano in itunes and it says "an ipod has been detected, but could not ne identified properly"
Hello rachel167,
I would use this:
iPod nano: Error message saying that iPod 'could not be identified ...
Ensure you use every step.
Hope this helps.
~Julian -
When I try to sync my iPod nano, it opens up driver E and then nothing happens
When I try to sync my iPod nano, it opens up driver E and then nothing happens.
I have searched all over for troubleshooting help.
Doublechecking. In the course of your troubleshooting to date, have you worked through the following document?
iTunes: Error 13019 during sync -
When I try to use iMessage on my iPod touch 4 (ios6) the iPod shuts down and restarts
Every time I try to open my iMessage my iPod shuts down. I have a 4th gen iPod with ios6. I will attempt to open the app and it will either shut down and restart as soon as the white screen comes up or I will see my previous messages and try to open a thread then it will restart. I have tried restarting the phone as well as turning iMessage on as off. Has anybody else had this problem? What can I do?
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
-Note this will delete messages currently on the iPod:
Go to settings>Messages>Send and Receive and sign out of Messages and sign back in.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem. -
When I try to open iPhoto I get a window dialog that says...
Your photo library is either in use by another application or has become unreadable
Shut down and restart your computer, and then open iPhoto again. If the problem persists, try rebuilding your photo library. To do this, quit iPhoto, and then reopen it while keeping the Option and Command keys pressed. You can also try restoring your photo library from a backup.
I have tried the reopen it while keeping the Option and Command keyes pressed.
No change.
I dee nothing but a blank page,
Any help would be appreciated.
Also hace back ups of all images on cd's. dvds and jump drives.
Any advice is appreciated.Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Repair Database. If that doesn't help, then try again, this time using Rebuild Database.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. (In early versions of Library Manager it's the File -> Rebuild command. In later versions it's under the Library menu.)
This will create an entirely new library. It will then copy (or try to) your photos and all the associated metadata and versions to this new Library, and arrange it as close as it can to what you had in the damaged Library. It does this based on information it finds in the iPhoto sharing mechanism - but that means that things not shared won't be there, so no slideshows, books or calendars, for instance - but it should get all your events, albums and keywords, faces and places back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.
Regards
TD -
When I try to download xcode 4.6.2, my computer shuts down and restarts telling me I have an error. HELP?!?? Can anyone help me?
Wed Jun 12 21:40:11 2013
panic(cpu 6 caller 0xffffff80190ac90b): Releasing non-exclusive RW lock without a reader refcount!
Backtrace (CPU 6), Frame : Return Address
0xffffff81096e3a80 : 0xffffff801901d626
0xffffff81096e3af0 : 0xffffff80190ac90b
0xffffff81096e3b10 : 0xffffff801911c09c
0xffffff81096e3d40 : 0xffffff8019110e92
0xffffff81096e3d70 : 0xffffff80190ff954
0xffffff81096e3ef0 : 0xffffff80190ffa10
0xffffff81096e3f50 : 0xffffff80193e182a
0xffffff81096e3fb0 : 0xffffff80190ced33
BSD process name corresponding to current thread: installd
Mac OS version:
12C60
Kernel version:
Darwin Kernel Version 12.2.0: Sat Aug 25 00:48:52 PDT 2012; root:xnu-2050.18.24~1/RELEASE_X86_64
Kernel UUID:
Kernel slide: 0x0000000018e00000
Kernel text base: 0xffffff8019000000
System model name: iMac11,3 (Mac-F2238BAE)
System uptime in nanoseconds: 11938612497736
last loaded kext at 606795969288: com.line6.driver.xtaudio 7.2.3 (addr 0xffffff7f9b360000, size 1024000)
last unloaded kext at 207361764339: com.apple.driver.AppleUSBUHCI 5.2.5 (addr 0xffffff7f99ac8000, size 65536)
loaded kexts:
com.line6.driver.xtaudio 7.2.3
net.telestream.driver.TelestreamAudio 1.1.0
com.logmein.driver.LogMeInSoundDriver 1.0.2
at.obdev.nke.LittleSnitch 3876
com.seagate.driver.SeagateGoFlexBlockSizeAdjuster 5.2.2
com.apple.driver.AppleBluetoothMultitouch 75.15
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.driver.AudioAUUC 1.60
com.apple.driver.AGPM 100.12.69
com.apple.driver.AppleMikeyHIDDriver 122
com.apple.driver.AppleHDA 2.3.1f2
com.apple.filesystems.autofs 3.0
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.driver.AppleUpstreamUserClient 3.5.10
com.apple.iokit.IOBluetoothSerialManager 4.0.9f33
com.apple.kext.AMDFramebuffer 8.0.0
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AppleMikeyDriver 2.3.1f2
com.apple.driver.AppleBacklight 170.2.3
com.apple.driver.AppleLPC 1.6.0
com.apple.driver.ApplePolicyControl 3.2.11
com.apple.AMDRadeonAccelerator 1.0.0
com.apple.iokit.BroadcomBluetoothHCIControllerUSBTransport 4.0.9f33
com.apple.driver.AppleMCCSControl 1.0.33
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleIRController 320.15
com.apple.driver.AppleUSBCardReader 3.1.0
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 34
com.apple.iokit.SCSITaskUserClient 3.5.1
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.2.2
com.apple.driver.AppleUSBHub 5.2.5
com.apple.driver.AppleFWOHCI 4.9.6
com.apple.iokit.AppleBCM5701Ethernet 3.2.5b3
com.apple.driver.AirPort.Atheros40 600.70.23
com.apple.driver.AppleAHCIPort 2.4.1
com.apple.driver.AppleUSBEHCI 5.4.0
com.apple.driver.AppleEFINVRAM 1.6.1
com.apple.driver.AppleACPIButtons 1.6
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleHPET 1.7
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.6
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 196.0.0
com.apple.nke.applicationfirewall 4.0.39
com.apple.security.quarantine 2
com.apple.driver.AppleIntelCPUPowerManagement 196.0.0
com.apple.driver.AppleBluetoothHIDKeyboard 165.5
com.apple.driver.AppleHIDKeyboard 165.5
com.apple.driver.IOBluetoothHIDDriver 4.0.9f33
com.apple.driver.AppleMultitouchDriver 235.28
com.apple.driver.DspFuncLib 2.3.1f2
com.apple.kext.triggers 1.0
com.apple.iokit.IOSurface 86.0.3
com.apple.driver.AppleUSBAudio 2.9.0f6
com.apple.iokit.IOAudioFamily 1.8.9fc10
com.apple.kext.OSvKernDSPLib 1.6
com.apple.iokit.IOSerialFamily 10.0.6
com.apple.iokit.IOBluetoothFamily 4.0.9f33
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.driver.AppleGraphicsControl 3.2.11
com.apple.iokit.IOAcceleratorFamily 19.0.26
com.apple.iokit.IONDRVSupport 2.3.5
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport 4.0.9f33
com.apple.driver.AppleHDAController 2.3.1f2
com.apple.iokit.IOHDAFamily 2.3.1f2
com.apple.driver.AppleSMBusPCI 1.0.10d0
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.kext.AMD5000Controller 8.0.0
com.apple.kext.AMDSupport 8.0.0
com.apple.driver.AppleSMBusController 1.0.10d0
com.apple.iokit.IOGraphicsFamily 2.3.5
com.apple.driver.AppleSMC 3.1.4d2
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.IOPlatformPluginFamily 5.2.0d16
com.apple.iokit.IOUSBHIDDriver 5.2.5
com.apple.iokit.IOUSBMassStorageClass 3.5.0
com.apple.driver.AppleUSBMergeNub 5.2.5
com.apple.driver.AppleUSBComposite 5.2.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.5.1
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOFireWireSBP2 4.2.0
com.apple.iokit.IOSCSIBlockCommandsDevice 3.5.1
com.apple.iokit.IOAHCISerialATAPI 2.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.1
com.apple.iokit.IOUSBUserClient 5.2.5
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.iokit.IOEthernetAVBController 1.0.2b1
com.apple.iokit.IO80211Family 500.15
com.apple.iokit.IONetworkingFamily 3.0
com.apple.iokit.IOAHCIFamily 2.2.1
com.apple.iokit.IOUSBFamily 5.4.0
com.apple.driver.AppleEFIRuntime 1.6.1
com.apple.iokit.IOHIDFamily 1.8.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 220
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.DiskImages 344
com.apple.iokit.IOStorageFamily 1.8
com.apple.driver.AppleKeyStore 28.21
com.apple.driver.AppleACPIPlatform 1.6
com.apple.iokit.IOPCIFamily 2.7.2
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0 -
i have the ipod touch 5 generation. As I try to charge my ipod it wont charge unless it is laying down and can not be straight up. does anyone have a idea on what i can do????
- See:
iPod touch: Hardware troubleshooting
- Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
I upgraded to lion. I now have the spinning wheel on the startup screen when I try to enter my user name and password. I tried shutting down and restarting, no luck
Reinstalling Lion Without the Installer
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alterhatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer. -
MBP 13" late 2011. when I turn it on it goes to an update screen then just shuts down
Lately I had problems when I recharged the battery, charging is constantly interrupted... And now, when I turn it on it goes to an update screen, then just shuts down. O.S: MAVERICKS
PLEASE HEEEELP!
P.D: Sorry for my english.LaCalle,
you can try this: boot your MacBook Pro into Recovery mode by holding down a Command key and the R key as it starts up. Once the OS X Utilities menu appears, select Disk Utility. On the left-hand side of the Disk Utility window, select your internal disk’s boot partition (typically called “Macintosh HD”). On the right-hand side, select the First Aid tab if it’s not already selected, then press the Verify Disk button if it’s not greyed out; if it is greyed out, or if it reports that errors were found, press the Repair Disk button. Once the verification/repair is completed, exit Disk Utility and select Restart from the Apple menu to restart in normal mode. Does it get past the update screen now? -
when i click to open firefox it says that "firefox is already running but is not responding. To open a new window, you must first close the existing Firefox process, or restart your system." and I've tried to shut down and restart my computer but it keeps showing the same message. I've even uninstalled Firefox and then reinstalled in the hopes that the problem would be solved but it this message is still popping up. What can I do to solve this problem?
== This happened ==
Just once or twice
== I was on facebook trying to upload pictures yesterday. ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; .NET CLR 1.0.3705; .NET CLR 1.1.4322; Media Center PC 4.0; InfoPath.1)Do you have a profile lock file in your profile folder? If so, delete it and see if TB runs properly:
http://kb.mozillazine.org/Profile_in_use#Remove_the_profile_lock_file -
i cannot open iphoto- the message I am getting says Shut down and restart your computer, and then open iPhoto again. If the problem persists, try rebuilding your photo library. To do this, quit iPhoto, and then reopen it while keeping the Option and Command-
I tries and it doesnt work!!What version of iPhoto? Assuming 09 or later:
Option 1
Back Up and try rebuild the library: hold down the command and option (or alt) keys while launching iPhoto. Use the resulting dialogue to rebuild. Choose to Repair Database. If that doesn't help, then try again, this time using Rebuild Database.
If that fails:
Option 2
Download iPhoto Library Manager and use its rebuild function. (In early versions of Library Manager it's the File -> Rebuild command. In later versions it's under the Library menu.)
This will create an entirely new library. It will then copy (or try to) your photos and all the associated metadata and versions to this new Library, and arrange it as close as it can to what you had in the damaged Library. It does this based on information it finds in the iPhoto sharing mechanism - but that means that things not shared won't be there, so no slideshows, books or calendars, for instance - but it should get all your events, albums and keywords, faces and places back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.
Regards
TD -
My MacBookPro (mid 2012) will not complete the boot process. Yosemite's progress widget gets about 1/3 to 1/2 way across when the logo disappears and the screen goes all white for 10-15 secs, then the machine shuts down and restarts. This sequence will repeat seemingly forever unless I shut it down manually.
I upgraded to Yosemite from Mountain Lion a couple months ago, skipping Maverick completely, and I've done any associated updates that Apple told me about. I don't recall which version of Yosemite I have, but I'm sure it is the "latest and greatest".
I've tried re-starting in Safe Mode / Safe Boot and that does the same thing as described above except without the endless restarts. Instead of restarting at some point, SafeBoot proceeds to the white screen and then it hangs until I restart it manually. (I've waited as long os 20-30 minutes with no response).
When I tried the option-command-p-r key combo I never get any chimes or other noises besides the original 1 time boot sound that you would expect to get when starting up a macbook pro.
I was using the mac quite normally (meaning I was doing work I normally do on it and there was no indication of anything wrong) immediately prior to this happening.
The machine is BootCamp(ed) with Windows 8.1 which I use from a VMWare virtual machine instead of natively so that I can have both OSes running at the same time. I also think this is unrelated to my problem. I have been using this setup for more than 2 years.
My upgrade to Yosemite was uneventful and I thought it went well and was very smooth. I don't want to lead attention away from Yosemite, but at this point my problem does not seem related to the upgrade.
Any help is appreciated.Install or Reinstall OS X from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
the Security button and set the Zero Data option to one-pass. Click on
the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless. -
Good day all,
I am new to Mac. Just want to find out if your Macs always prompt you to shut down and restart. Mine happens very often sometimes, and it can be very embarrassing, especially just when you think you are almost done with what you are doing, only for you start all over again. Or, is there anything I am doing wrong, somebody please help, Thanks.
Francis.Hi Francis,
Are you getting kernel panics?
http://support.apple.com/kb/TS3742
http://www.thexlab.com/faqs/kernelpanics.html
Maybe you are looking for
-
How to create additional column in CM21, CM25
Hi, my task is to add additional column into the orders grid of cm25. I found that the user exit CYPP0005 could be used for that. Can anyone share an example of implementing EXIT_SAPLCYPP02_001? Best regards, Pavel.
-
Abap / SAP on AS400 / EBCDIC
Hi all, we have some problems here with one of our customer installations. Until now every RFC and Abap program that we have installed at different customers works fine. Most of them use Win or Linux as their platform. Now we have a customer wich is
-
Hello forum, having just purchased a new eMac and finding everthing as great as my last one apart from my screen! It seems to me that there is a large area at the centre of the screen with a magenta cast. When calibrated with my Spyder Eye One it giv
-
Want to know about photo booth
Want to know about photo booth
-
Hi, I have account with PIA and it doesn't seem to work with bt openzone. So I was looking to see if BT provided some kind of VPN and I can see on http://bt.custhelp.com/app/answers/detail/a_id/14923/~/how-do-i-download-vpn-software-for-bt-wi-fi that