When i turn my ipod touch 4g on it goes from the apple logo to the white wheel then to a blank white screen, please help
After using itunes to restore it i turned my ipod touch on and it stayed on the apple logo for a few minutes then it would change to a spinning wheel on a black screen then the screen would turn white and the process will repeat. I can still put it in dfu mode and recovery mode but they don't help. So hopefully someone in this community can help me. And this all started when i updated it to ios 6.1.3 from 6.1.2. and also my computer and itunes dont recognize it
See if you missed anything here:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Similar Messages
-
When i turn my ipod touch on it stays at a white screen whats wrong with it anyone
when i turn my ipod touch on the screen stays white what is the problem
That symptom is covered here:
iPod touch: Hardware troubleshooting -
When I turn my Ipod touch on it keeps asking me to sign in to Icloud I put my password it and it says its wrong I have reset it 10 times already what do I do?
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Go to Settings>iTunes and App Store and sign out and sign back in
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings -
I just bought a philips fidelio docking speaker and when I plug my iPod touch 4th gen it charges but dosent play music through the speaker.
Does Phillips say it will work with a 4G iPod with 6.1.5?
Have you went to their support site?
Which dock did you get?
This one
http://www.usa.philips.com/c-p/DS8500_37/-/specifications
says only compatilbe with the 1G, 2G and 5G iPod tpouchs (as well as some other iOS devices) -
Help my ipod touch is stuck on the apple logo and a little wheel!
Help my ipod touch is stuck on the apple logo and a little wheel! What do I do I cant restore, or turn it off. WHAT DO I DO?
Press and hold the button on the top and the button on the front at the same time.
This should reset the iPod. -
My ipod nano 6th gen doesn't start. When I plug it, only blink the apple logo on the screen. I try to reset it holding by 8 seconds start button and volume down and doesn't work. My Ipod doesn't have any shock or water damage. How can I do?
Hey rulosrojos,
The article linked below details a number of troubleshooting steps that can help restore functionality to your iPod nano.
iPod nano (6th generation): Hardware troubleshooting
https://support.apple.com/en-us/TS3474
Sincerely,
Allen -
My ipod touch is blocked with the apple logo on the screen
How can i unblock my ipod touch? I rebooted it and has got blocked with the apple logo on the screen.
The computer does not "see" it although it is connected.Try here:
iPhone and iPod touch: Frozen and unresponsive -
Ipod 5th Gen is stuck on the apple logo with the loading bar not moving
So I recently decided to restore my iPod 5th gen to factory settings, because I plan on selling it to a friend. When I chose the option to erase all data and reset settings, the iPod turned off, and then came to the black background with the apple logo in the middle. After watching it turn on and off, and not do anything for at least an hour, I searched for answers on the forum. I found that I should reset my iPod by holding the center button and the top right button at the same time for at least ten seconds, or until the device shuts off and then the apple logo is visible again. After I did this, once again, the black background with the apple logo popped up, this time with a loading bar beneath it. After an hour or two of checking on the progress bar, I noticed that it had not made any progress whatsoever. It had not moved an inch since I first started it. What do I do?
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
hello my name is kirstie, i updated to firmware 4.2.1 .....my iphone 3g stays on the apple logo for about 4 minutes then flashes white and goes back to the apple screen, it repeats untill battery is flat, every now and then im lucky enough to get it to turn on but not very often and then it freezes and repeats the same problem?? (if i turn the phone off my pressing the two buttons it wont keep rebooting, its only when i leave it after turning it on)
I have reset the phone, full firmware restore, even downgraded back from firmware 4.2.1 to .3.1.3 official by using dfu mode and still doesnt fix.
(i correctly got out of dfu mode after the downgrade)
i can enter dfu mode and recovery, and update through itunes with no problem, but it doesnt fix the problem,
i have searched and found no answer to this problem, every option availible to try that i know of i have tried and failed. i dont care about preserving my content i just want a fix. i have a good understanding how to operate software on a computer and shouldnt be too confused by any advice given, so plz even if the answer is very complex i wish to try anything, please help me to get my iphone working.Anyone have any suggestions? or is everyone else just as clueless as me !
-
Ipod nano 4th generation switches between the Apple logo and the menu
I have a 4th generation 8 g iPod Nano that probably has about 1 hour of use since my wife won it in a raffle over a year ago. When I went to recharge it yesterday, the only thing that happens is that the display, when connected to the computer, flips back and forth between the Apple logo and the menu screen. Whenever either one of them appears, it will disappear in a few seconds, then repeat the sequence. I have done a reset and restore,and installed the latest software version but the same thing happens over and over again. If the iPod is detached from the computer, ie, its power source, NOTHING happens on the display. It black and you can't get it to show anything. My theory was that the battery needed to be replaced even though it wasn't used much in the year since she got it. In fact. the absence of use and recharging it and discharging it may have lead to this problem in the first place. However, my one issue with that theory is that, when connected to a power source, like the computer, I would think I could get it to function normally, which I can't. I was able to get to the "service menu" which won't disappear when I move about different choices, as long as its connected to the computer. Again I can get nothing if its not connected to a power source.. does anyone think that this problem could be solved by replacing the battery or does it seem like that is only part of the problem? Thanks for any help and suggestions you may have to offer.
GeoffDespite the Nano only being used for an hour or so, the battery needed to be replaced= problem solved!!
-
My iphone 4 randmonly started going into recoveery mode when i was trying to download ios 7.1, and now the apple logo will come one and then fade to black and continue this process. My iphone wont restore either and will get the 3194 error message.Help please!
Hello chindeepchow,
Thank you for using Apple Support Communities.
For more information, take a look at:
Resolve specific iTunes update and restore errors
http://support.apple.com/kb/ts3694#3000
Resolve communication issues
Related errors: 17, 1004, 1013, 1638, 3014, 3194, 3000, 3002, 3004, 3013, 3014, 3015, 3194, or 3200. These alerts refer to gs.apple.com, say "There was a problem downloading the software," or say the "device isn't eligible for the requested build."
Check the hosts file or TCP/IP filtering, which might cause communication issues between iTunes, ports, and servers.
Have a nice day,
Mario -
Just upgraded my iPad to IOS5 and when the download was completed, a window said that there was an error and it could not restore. Now I have a black screen with the Apple logo and the circle lines. None of the buttons respond. Help, please!!
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. Maybe this will let the iPad reboot and then you may need to restore again but see if this helps to start the iPad first.
-
Hi, I am not able to reboot my Mac desktop.
When I switch on the Mac, I get a white screen with the Apple logo and the little rotating circle.
The system refuses to boot.
What can I do?
MarcusWe need to get you moved. This forum is for mini-tower Macs built between 1998 and 2005 and doesn;t get as much traffic ("eyeballs on the problem") as the forums for newer Macs.
Please do "About this Mac" from you Apple menu and tell us what that says for "processor" and Mac OS version. Looks like this:
or this for later Mac OS versions:
With that we can figure out which of the two iMac forums you need and get the Hosts to move your post. -
When opening my MBP, all that shows is the apple logo and the forbidden sign
Hello everyone,
So I'm on a 2011 MPB using 10.9.5.
I've closed it after using two nights ago, and when I came back home the day after and tried opening it, all that appeared was an alternation between the apple logo and the forbidden sign (here it is : http://stickeramoi.com/3447-3369-large/autocollant-panneau-interdit-interdiction .jpg)
I've tried repairing the disk but that failed.
Tried also re-installing OS X on it but that took about 17 hours (which is ridiculous) so I've cancelled that and instead, tried restoring a Time Machine save.
After it finished restoring the latest backup, I'm still faced with the same problem. It just won't boot.
Thank you for your time and help,Yeah well I think I've tried about everything that I found out there.
From console commands to installing Lion through Internet recovery...That's it, I give up
Will take it for replacement tomorrow.
Thank you -
iPad went black and has the apple logo with a little wheel at the bottom. Tried turning on and off doesn't work.
Try a Reset...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430
If no joy...
Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414
Maybe you are looking for
-
Export List Of Images Selected Along With Some MetaData
It would be extremely beneficial for LightRoom to have the ability to have an Export feature that creates an ASCII or XML file format (or other common format) of the image file names (and path) that are highlighted/selected. Since LightRoom is a grea
-
I am using UTL_FILE to write data into an excel file. The problem is it shows as garbage data ("ä") as there are UTF8 Charcters in that. I have tried using utl_file.fopen_nchar & other nchar functions but it is still not displaying correctly Databas
-
Can CRM Load to Two BW Systems?
Veterans, Can an existing CRM Source system viably concurrently load into multiple BW (NW04s) Target productive systems? If it can, what precautions are needed to ensure viability of delta loads? I've reviewed landscape Note 775568 and it's caveats a
-
SELECT statement (urgent!)
Could you please help me with the following statement? The FROM clause is incorrect but i don't know what i should write. Thank you in advance. Maria. DECLARE A NUMBER; CURSOR C1 IS SELECT TABLE_NAME, COLUMN_NAME FROM USER_TAB_COLUMNS WHERE NULLABLE=
-
Non-Editable Regions being edited
I have created a whole site in dreamweaver with editable regions set up as i usually do. In contribute 3 i can edit the site no problem, however if it is edited in version 4, my non-editable regions have some mm_lock code in part of the javascript. T