When my computer starts up it says hard disk error g6-1b87cl

when my husband was updating my computer he turned it off n now when i turn my computer back on it says hard disk error..... i need help..... ne ways computer is a pavilion g6-1b87cl notebook pc its windows7 intel pentium inside

Enter BIOS setup by tapping/holding the F10 key immediately after powering on the laptop.Use Diagnostics to test your hdd.
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Similar Messages

  • Error when trying to install Mountain Lion - says hard disk is damaged :(

    I downloaded and installed Mountain Lion on my iMac today - without any problems. But when I downloaded it to my Macbook pro (bought 2010) I get an error message telling me the installation cannot continue due to hard disk error My harddisk was fine before the installation, to my knowledge ...
    Of course I tried disk utility (during the installation) and it tells me the disk needs to be repaired but I can´t choose "Repair disk" since it is grey (no write permissions it says). What can I do? I really need help!!!

    I rarely post, however, because of a major screw up with Mountain Lion, I will.  I have been using mac computers since 1987, have obviously installed and upgraded multiple OS new and upgrades and never, I mean never had a problem with any of them, until now.  The install stalled with the message that the hard disk needed repair.  I thought all of my data was lost, except for time machine backup, which was not as current as it should have been.  Losing that data would have been a royal pain. 
    Went through the restore OS from Time Machine, then tried to repair the disk with apple disk repair utility.  Not repairable.  Why?  I still don't have a clue.  After reading multiple threads, decided to go ahead and buy DiskWarrior.  This was a weird experienc.  Loaded it onto external hard drive, hooked my MacBook Pro as Target disk.  Loaded in DiskWarrior as hardware probelm.  ????  Immediately went online to see what advice about this message.  Looked like a massive coincidence had hit my laptop.  Worked perfectly until loading Mountain Lion, the decided to have hard disk melt down.  Suddenly, DiskWarrior indicated it was ready to rebuild my directory.  The hardware warning was gone.  A few minutes later, directory repaired.  Rebooted, same problem.  Can't load OS X, need to repair hard disk.  Apple disk repair still unable to repair disk.  Used DiskWarrior, repaired it no problem. 
    Deleted original OS 10.8 dmg.  Rebooted and downloaded fresh copy of OS 10.8.  This time install went flawlessly.  Mountain Lion transferred all info flawlessly.  Mid 2009 MacBook Pro running flawlessly and actually more smoothly now than in Lion.
    1.  I think original download was somehow corrupted and that is what screwed up the disk directory.
    2.  I do not know why apple Disk Utility would not repair the disk and Disk Warrior would.  Expensive fix, but ultimately worthwhile.  Did it mysefl and did not have to mess with "Genius" bar.
    3.  I will never go so long without backup again.  That was a big mistake.
    My advice:
    1.  Be sure you have smooth download of entire Mountain Lion file, if not, start over.  My download was paused a couple of times.
    2.  If the install is messed up and you need Disk Repair, buy DiskWarrior and repair directory, it works flawlessly.  If it initially says your disk has hardware problem, wait a few minutes while it finishes entire evaluation.  It may well disappear like mine did, then actually repair the directories without a problem.
    3.  Be sure you have deleted old OS 10.8 Install file and load fresh one.
    4.  Install OS 10.8 and you should be OK.
    5.  Good luck.
    Mountain Lion seems to have some problems, but many of them may be due to server overload at apple, delayed download with incorporated unrecognized code problems.  If there is any delay, start over and get a smooth download.
    Disk Utility is too light weight.  Apple needs to beef it up.  This is my biggest complaint.  Apple utility should be able to fix disks.  We should not have to spend $100 to fix a disk, but there you are.
    Once fixed however, back to usual beautiful, flawless apple experience.

  • Bluetooth no longer loads automatically when the computer starts

    I have the Bluetooth Stack version 2.01.21.1. It was working fine. When the laptop booted up, the bluetooth mouse was automatically connected.
    All of a sudden the icon no longer appears automatically in the system tray and so I have to manually connect the mouse each time
    It is still listed in the startup menu on the desktop and it is still checked in startup in the msconfig.
    How do I fix this?
    Thanks in advance

    I have just gotten off the phone with a microsoft tech who actually seems to have fixed this somewhat
    He went to start/run to get to services.msc.
    He chose "SSDP Discovery Services" which "enables discovery of
    UPnP devices on your home network" and DISABLED it.
    Go figure
    The BT icon now appears in my system tray and starts up automatically when the computer starts.
    I say somewhat because It still disconnects if left idle for a long period, which it did not do previously, but at least it is there when I log on.
    I want to mention that I have a Dell, not a Toshiba (did not realize this forum was for Toshiba laptops rather than Toshiba software) but perhaps
    you will find this information useful.
    Also, at http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx you will find an autorun tool that lets you fix what is or is not
    in the startup menus. It seems to work better than using msconfig which on my laptop was not making a difference as to what started up and what did not.
    It is meant for IT professionals so I would not mess with it too much. However if you just check or uncheck in the startups for the BT manager you will
    not do any damage.

  • Smart Hard Disk Error on windows 7 notebook

    I have a Hp Mini 2100-2190NR running windows 7.
    I've had a problem recently where i could not boot windows. I got it fixed using a USB recovery disk.
    When i start my computer i get a Smart Hard Disk Error message.
    It says it has detected an imminent failure and to back up the content immediately and run the hard disk test in system diagnostics.
    Once i run the tests, some got me errors and could not complete them.
    I tried using a system restore back to a date and i was able to log into windows. The next day same problem occured and tried another system restore and nothing happened.
    Im stuck at the black screen with the microsoft corporation loading bar.
    How can i fix this problem?
    This question was solved.
    View Solution.

    Hi,
    The Smart error message would indicate that the Hard Drive is failing and needs to be replaced.  This is also consistent with the start-up issue.
    If your notebook is still under warranty, contact HP and arrange to have the drive replaced - you can check your warranty status Here.
    If you live in the US, contact HP Here.
    If you are in another part of the world, start Here.
    If you are out of warranty and would like a guide on replacing the Hard Drive yourself, please let me know.
    Best regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • HP Pavilion dv7-4165dx SMART Hard Disk Error Hard Disk 1 (301)

    My HP Pavilion dv7-4165dx when first turned, the screen reads "SMART Hard Disk Error" "Hard Disk 1 (301)

    blackeneds
    Your System supported HDD to 1 TB Page 2 , 55 and 107http://h10032.www1.hp.com/ctg/Manual/c02657339.pdf
    Sata III works
    Say thanks by clicking the "Kudos! Star" which is on the left.
    Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue.

  • I have a stuck CDR disk in my MacBook. I have tried everything and nothing works. When the computer starts it makes weird sounds and also when I try to eject it. Nothing Works! Please Help.

    I have tried everything and nothing works. When the computer starts it makes weird sounds and also when I try to eject it. Nothing Works! Please Help.

    I had that happen with a MacBook. It turned out that the metal case above the slot was slightly bent down.
    Putting a flat blade screwdriver in the slot and gently twisting it to move the metal case up allowed it to eject. Don't put it in too far you only want to bend the case not the drive.
    The case can get bent down by picking it up with your thumb pressing down on the case above the slot.

  • Strange icon when the computer start up

    I just recently noted that when my computer start up a blue icon that looks like the Earth flashes for a couple of seconds and then a folder with a question mark appers and flashes and, finally, the log on window comes up.
    It's that a serious issue?

    In that case, I recommend you run Utilities > DiskUtility and confirm that the SMART status of your drive is "Verified".
    This checks to see if your HD is starting to fail. Verified is good.

  • Computer is hanging frequently​. Hard Disk is also not too loaded.

    Now a days my computer is hanging frequently. Hard disk is also not too loaded

    Hi
    Please find the link givenbelow might help you to resolve your issue.
    How to Troubleshoot Problems When a Computer Does Not Start Up or Boot Properly
    Let us know how it goes!
    "I work for HP."
    ****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath

  • Hard Disk error on start up

    Hi,
    I have a hard disk error on start up of my HP Pavilion Dv7-5003tx. When I run Hard disk test it fails, error code 0G8421-50N63H-0G8421-60DC03.
    How do I resolve this?
    Regards
    John.

    Hi John,
    The error will either be a Smart or Disk Self Test failure - both would indicate that your Hard Drive is failing and will need to be replaced.
    If your notebook is still under warranty, contact HP and arrange to have the drive replaced - you can check your warranty status Here.
    If you live in the US, contact HP Here.
    If you are in another part of the world, start Here.
    If you are out of warranty and would like a guide on replacing the Hard Drive yourself, please let me know.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • I suddenly started getting hard disk error from a fictitious recovery software how do i get rid

    I suddenly started getting hard disk error on my compaq laptop and some software called file recovery start running scans showing all sorts of errors and hiding all my files. I've lost all my icons can't see any files in explorer and upon looking into this found that this may be a fictitious software that has gotten installed on my laptop while browsing through some web sites. all was fine and the problem started while I was in the middle of brwoing some websites.
    I am trying to unhidew files but I can't get to my control panel as it does not seem to be there.
    Can someone please help. When I looked this i found a website telling descrbing everything that is happeniing on my screen and telling me that this is a fictitious software and gave me various options to resolve but I'm not sure if I should trust this site or not.
    Please help. Its my old mum's laptop and she really needs my help on this.
    Many thanks
    Rekha

    Try to download MalwareBytes and do a scan/cleaning with it:
    http://download.cnet.com/Malwarebytes-Anti-Malware/3000-8022_4-10804572.html?part=dl-10804572&subj=d...
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • How to resove the "smart hard disk error" problem occured message displayed while starting up?

    Dear HP Technician
    My HP laptop showing me a "Smart Hard disk Error" while starting up the computer when I press power button on.
    The message displayed on black screen is as below:
    Smart hard disk error
    The smart disk check has detected an imminent failure. To ensure not data loss, please backup the content immidiately and run the Hard Disk Test in system Diagnostics.
    Hard Disk 1 (301)
    F2 system Diagnostics
    Enter-continue startup
    Fore information, please visit:
    www.hp.com/go/techcenter/startup
    I already did the Hard disk self test and it showed all the test were passed.
    Please help me to resolve this problem
    thank you
    regards
    neeraj
    +61 0432247152

    There are 2 ways of running a test on your hard drive . One way is through BIOS (F10) and other is through HP System diagnostics(F2). How exactly was test initiated from your end ?
    The SMART imminent failure for Hard drive is an indication that your Hard drive is on verge of failure or might fail anytime depending on usage. I would recommend you to backup your files immediately because your hard drive might die at any moment and I'm pretty sure its needs to be replaced.
     Kindly check the instructions over here in order to run the test for your hard drive
    //Click on Kudos and Accept as Solution if my reply was helpful and answered your question//
    I am an HP employee!!

  • Cumputor say hard disk not exist

    Hi I have a hp pavillion dv6notebook pc was working last night went off all I have is a black screen and it says hard disk not exist start up test was ok diagnostic log says f11 error lol 03f0i have no idea what's happened can you help

    Sounds lik the hard drive has failed and will have to be replaced. Did you test the hard drive using F2 Diagnostics?
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • My iTunes won't open! I uninstall it and re-install! When I try to open it says locked disk

    My iTunes won't open! I uninstall it and re-install! When I try to open it says locked disk?

    Hey pierrejordan,
    Thanks for the question. The following article that goes over what to do when you receive a "Disk is locked" error on your Windows computer. Try out the steps within and see if that resolves the issue:
    iTunes for Windows XP: "Disk is locked" or "iTunes folder cannot be found" when installing or opening iTunes
    http://support.apple.com/kb/ht1866
    Have a good one,
    David

  • When restarting my HP laptop, it's showing Hard Disk error.

    when restarting my HP laptop, it's showing Hard Disk error. I have already done two time formatting. But it's still there. please suggest me what to do?

    Edited to avoid duplicate post
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • My screen blacks out and computer starts up again due to an error. Anyone any suggestions what could case this?

    My screen blacks out and computer starts up again due to an error. Anyone any suggestions what could case this?

    Hello nattygrimm,
    I was looking into the issue you are describing and found a great resource to try and fix the issue without having to re install the OS. It is an article called Mac OS X: How to troubleshoot a software issue found here: http://support.apple.com/kb/HT1199.
    I recommend starting here:
    The first and easiest test to try is to see if the issue affects a different user account on your Mac. Each user account has customized preferences and other items stored in its home directory. You'll first need to create an additional user if one does not already exist (follow steps a-h below). Then, log out of the current user and test the issue in the new user account.
    If this resolves the issue, there may be an issue with a file in the home directory of the original user account.
    From the Apple menu, choose System Preferences.
    From the View menu, choose Accounts (or choose Users if using Mac OS X v10.2 or earlier).
    Click "+" (or click New User if using Mac OS X v10.2 or earlier).
    Give the new user a name and short name.
    Mac OS X v10.3 or earlier only: Click the Password tab, and give the user a password.
    Mac OS X v10.3 or earlier only: Click Security.
    Select the checkbox for "Allow user to administer this computer". This makes the user account an administrator.
    Click OK, or quit System Preferences.
    Work your way down the article as needed.
    All the best,
    Sterling

Maybe you are looking for

  • Error while Installation of EP 7.0

    Hi Experts , I am facing an error while i run the file sapinst.exe . This error comes after completing the following steps : SAP netweaver 7.0 support release 3.0 -> Central System->Custom->Continue with Old option . After i select the last option i

  • Reg problem in Runtime Constants $SenderService

    Hi       Have a problem , I am using ABAP XSLT Processor  mapping (I have used message split for this particular scenario i.e. input is single file and output is multiple file) Instead of hard coding the sender service i tried to use Runtime Constant

  • M251nw not being recognized

    Just purchased a brand new m251nw, and I cannot get my computer operating on XP to reconize it.  I have used 2 different USB connectors, and have tried multiple usb ports on my computer.  I have rebooted, tried all kinds of different combinations all

  • Anyone using 7.0.98.0 with any BIG problems?

    I have 7.0.98.0 burning in at one of our locations with 8 WiSMs and 500+ clients for about 6 weeks now. We haven't had any big issues and are looking to move forward with another side deployment and eventually a campus wide deployment which consist o

  • ECLIPSE question...what am i doing wrong???

    hi, i downloaded Eclipse 3.1 recently and i started playing with it today. I noticed right away, though, that there is something strange and maybe I have some settings I need to adjust. I have a project called 'LOG' that sits in the root workspace di