When sharing a videos I get a rendering error: -50.  Any suggestions?

when sharing a videos I get a rendering error: -50.  Any suggestions?

I have an iMac, Processor: 2.7 GHz Intel Core i5, memory: 8 GB 1333 MHz DDR3, OSX 10.7.5, FCPX 10.0.8. I have no third party plugins. First time responding to community. Forgive any protocol errors.
Been working on variety of work projects for months prior to update with no problems. Took time off for a simple new project after updating to 10.0.8. Finished this small (11 minute) new project that is a combination of video and stills, with a few titles and simple transitions. Plays fine within FCPX, however, ran into same problem that started this chain, ie cannot share/export without getting same error message stated above related to a faulty frame.
Tried several share/export Master File settings. Tried moving project (from within FCPX) to another drive which resulted in same error message, but related to other different frames. Tried replacing original data in affected frame with freshly exported replacement files using QTime. Same problem again. Was able to export to Compressor, but resulting ProRes 422 file was so jumpy it wasn't usable.
Tried suggestions of Mark M 98021 and Hank LV, ie, halting all rendering in preferences and deleting render files. After this, I was successful in sharing/exporting at will.
I have several other major projects that I am afraid to return to. I'm not an expert at the inner workings of FCPX and don't have time to keep dealing with this issue. I can leave rendering off, but not a satisfactory solution. Not sure if old rendered files might become infected.
It would seem that there is a problem in the update. I hope this is corrected so I can continue with my work.

Similar Messages

  • TS1165 When sharing a project I get "frame 72938 (error -1)." and the sharing is stopped. What is this and how do I fix it. Thanks, Kerry

    When sharing a project I get "frame 72938 (error -1)." and the sharing is stopped. What is this and how do I fix it. Thanks, Kerry

    I have an iMac, Processor: 2.7 GHz Intel Core i5, memory: 8 GB 1333 MHz DDR3, OSX 10.7.5, FCPX 10.0.8. I have no third party plugins. First time responding to community. Forgive any protocol errors.
    Been working on variety of work projects for months prior to update with no problems. Took time off for a simple new project after updating to 10.0.8. Finished this small (11 minute) new project that is a combination of video and stills, with a few titles and simple transitions. Plays fine within FCPX, however, ran into same problem that started this chain, ie cannot share/export without getting same error message stated above related to a faulty frame.
    Tried several share/export Master File settings. Tried moving project (from within FCPX) to another drive which resulted in same error message, but related to other different frames. Tried replacing original data in affected frame with freshly exported replacement files using QTime. Same problem again. Was able to export to Compressor, but resulting ProRes 422 file was so jumpy it wasn't usable.
    Tried suggestions of Mark M 98021 and Hank LV, ie, halting all rendering in preferences and deleting render files. After this, I was successful in sharing/exporting at will.
    I have several other major projects that I am afraid to return to. I'm not an expert at the inner workings of FCPX and don't have time to keep dealing with this issue. I can leave rendering off, but not a satisfactory solution. Not sure if old rendered files might become infected.
    It would seem that there is a problem in the update. I hope this is corrected so I can continue with my work.

  • Having a problem installing any CS 5.5 application from disk. Get a Runtime error. Any suggestions?

    The error message says:
    Runtime Error!
    Program: C:\Temp\AIR9923.tmp
    This application has requested the runtime to terminate in an unusual way.
    I get the same message for every application I try and install.
    InDesign CS5.5 is already installed.
    Running Windows 7.
    Any help please?

    Thanks for the suggestion.
    I have re-installed the latest version of AIR and still get the same problem. The instillation crashes every time while it's trying to install the Abobe help files.

  • When sharing a video on You Tube I am unable to enter text

    When sharing a video from You Tube to Facebook I am unable to enter text in the text box. The video does go onto Facebook, I just can't enter a comment.
    == This happened ==
    Every time Firefox opened
    == Installed Firefox

    I had exactly the same issue, that the Apple wireless keyboard became unpaired, and I couldn't get past the password-protected log-in screen, because I didn't have a wired keyboard laying around.
    OK folks,
    Discovered by trial and error that it was the wireless mouse (not an Apple brand) that was preventing the keyboard from pairing, even though it's not a bluetooth mouse...
    Here's the steps I used...
    1. Disconnected the USB  mouse cord from the Mac Mini.
    2. Turned off the Apple wireless keyboard from switch on the back.
    3. Turn Mac Mini off, then back on.
    4. Waited for it to boot up as far as  the password-protected screen.
    5. Turned on the Apple wireless keyboard, waited for it to stop blinking, indicating (hoping) that it paired        up.
    6. And voila... was able to then type in the password...
    7. Then plugged the non-Apple wireless mouse sensor  cord back into the Mac Mini's USB port
    I also immediately went in to the MacMini's Sharing options and set that up for remote management in case something else happens down the road for other problems...
    Thanks though to all who suggested solutions... they may come in handy in the future.
    Hope this helps someone else...
    Lynda

  • When installing CS3 Design Premium it instals Version Cue server and shared components, but I get the message "Errors: 6 component (s)" and dose not install, Photoshop, Flash, Illustrator, Indesign or Creative Suite Premium

    When installing CS3 Design Premium it instals Version Cue server and shared components, but I get the message "Errors: 6 component (s)" and dose not install, Photoshop, Flash, Illustrator, Indesign or Creative Suite Premium

    Thank you Bturko in the future only migrate/copy/transfer your documents and settings.  Adobe applications especially are not designed to be transferred from one computer to another.  It is possible to recover however.  I would recommend the following steps:
    Run the uninstaller located in Applications/Utilities/Adobe Installers
    Run the CC Cleaner Tool to ensure complete removal - Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6 - http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html.
    If you need to download a fresh copy of the installation files they can be downloaded at Download CS3 products.
    Run the installer and reinstall Creative Suite 3.

  • When I try to start my macbook it gives an error of Please restart your computer, but when i do this i get the same error.

    When I try to start my macbook it gives an error of Please restart your computer, but when i do this i get the same error. This occured after my macbook pro shut down (because of low battery) while it was installing some updates. Please Help?

    Try reinstalling OS X. What version did you have installed? If it's Snow Leopard do this:
    Reinstall OS X without erasing the drive
    Do the following:
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.

  • When opening I-Tunes i get the following error message: an unknown error occured (-42032). What shall i do?

    When opening I-Tunes i get the following error message: an unknown error occurred (-42032). What shall i do?

    Hi,
    Try here:  http://forums.techarena.in/portable-devices/1394350.htm. 
    Hope this helps! 
    ---likeabird---

  • When exporting from Imovie I get the following error? OSStatus error -2009

    when exporting from Imovie I get the following error? OSStatus error -2009

    Hi
    Apple Support pages says.
    Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
    If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software.
    Yours Bengt W

  • Been visiting another country. when i got home i get an unknown error has occurred on both my iphone and ipad2 when trying to install or update anything from app store

    been visiting another country. when i got home i get an unknown error has occurred on both my iphone and ipad2 when trying to install or update anything from app store

    I started getting that message on my iPad tonight when I reset it completely. I haven't been t another country. So not sure if that has anything to do with it. I haven't been able to resolve yet.

  • I downloaded a new book and when i try to open get book format error. How do i resolve

    I downloaded a new book and when i try to open get book format error. How do i resolve

    Hello
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    Using Game Center
    http://support.apple.com/kb/ht4314
    If the issue persists, or certain features of a game aren't working as expected (leaderboards, achievements, and so on), use the App Store to report the problem to the developer
    Best of luck,
    Mario

  • When I startup Itunes I get "An Unknown Error Occurred -42110" Message.  Can you tell me what is wrong and how to resolve?

    When I startup Itunes I get "An Unknown Error Occurred -42110" Message.  Can you tell me what is wrong and how to resolve?

    Try the following user tip:
    iTunes for Windows 11.0.2.25 and 11.0.2.26: "Unknown error -42110" messages when launching iTunes

  • When I download itunes I get apple application error 2 on windows 8

    When I download itune I get apple application error 2 on windows 8

    See Troubleshooting issues with iTunes for Windows updates. Use the steps in the second box to repair your iTunes installation. Your library should be unaffected by these steps but there is backup advice elsewhere in the user tip.
    tt2

  • I can buy individual episodes of TV series however when I try and buy a full series I get a 5002 error.  Any ideas?

    I can buy individual episodes of TV series however when I try and buy a full series I get a 5002 error.  Any ideas?

    This Apple article might help ya out -> iTunes: Advanced iTunes Store troubleshooting
    "Error 5002"
    This alert is often the result of an issue with verifying your billing.
    Quit iTunes.
    Open iTunes.
    Test the issue.
    If it persists, sign in to store.apple.com using your iTunes account
    Click on Change account information
    Modify or remove your credit card information.
    Click Continue.
    Test the issue.

  • Since updating to Mavericks, Mail doesn't work properly.  It just stops working (no error messages--it just won't check for new mail) and I must shut it down and reopen it to get it working again.  Any suggestions?

    Since updating to Mavericks, Mail doesn't work properly.  It just stops working (no error messages--it just won't check for new mail) and I must shut it down and reopen it to get it working again.  Any suggestions?

    Try to force quit the mail app
    Double tap the home button. When you see the app previews on the screen scroll sideways if needed to get the preview in question on the screen. Flick that preview up and off the screen to close the app. Single tap the home button or home screen preview to exit the mode.
    Failing that, go into the settings, mail, contacts and calendars and remove your account info then put it back in and see if that works

  • My MX892 is clicking and can not draw paper - I get a load paper error message - any suggestions?

    My MX892 is clicking and can not draw paper - I get a load paper error message - any suggestions?

    Hi keciakh,
    To try and get the paper to feed, with a flashlight or other bright light, please check the paper feed area of the printer and verify that there are no paper jams or obstructions in the printer that may be causing the error.   Once this has been done, please look inside of the printer where the inks are located and ensure that there are no obstructions in there that may be causing the print head not to move freely.  Next, please remove and reseat all of the ink tanks in the printer.  Once all of these steps have been performed, please follow the steps below to perform a roller cleaning on the printer:
    You need to prepare: three sheets of A4 or Letter-sized plain paper  
    1. Make sure that the power is turned on. 
    2. Open the paper output tray gently. 
    3. Select Roller cleaning.
    (1) Press the MENU button.
    (2) Select Setup, then press the OK button.  The setup menu screen will appear.
    (3) Select Maintenance, then press the OK button.  The Maintenance screen will appear.
    (4) Select Roller cleaning, then press the OK button.
    The confirmation screen will appear.
    (5) Select Yes, then press the OK button.
    (6) Select the paper source to clean (Rear tray or Cassette), then press the OK button.
    4. Clean the paper feed roller without paper.
    (1) Follow the message to remove any paper from the paper source you selected in (6) of step 3.
    (2) Press the OK button.  The paper feed roller will rotate as it is cleaned.
    5. Clean the paper feed roller with paper.
    (1) Make sure that the paper feed roller has stopped rotating, then follow the message to load three or more sheets of A4 or Letter-sized plain paper in the paper source you selected in (6) of step 3.
    (2) Press the OK button.  The machine starts cleaning. The cleaning will be complete when the paper is ejected.
    (3) When the completion message appears, press the OK button.  The screen will return to the Maintenance screen.
    Reference
    To access other available functions, use the mode buttons or the MENU button.
    This didn't answer your question or issue? Please call or email us at one of the methods on the Contact Us page for further assistance.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Maybe you are looking for