When start Dreamweaver cs 5.5 system fatar error (c000021a) 0xc0000005

Hi all,
After dreamweaver cs 5.5 installation. i getting this below error and system has been shutdown
c00000021a (0xc0000005) system fatal error.
i am using win xp sp2 32bit system.
AMD phenom II x4 945 and 2 gb ram ddr3
i have installed photoshop cs5. but is working fine. but when i start dreamweaver sytem got shutdow.
Please give me solution for this.
thanks and Regards
srinivas

The error 0xC0000005 is generated by an illegal "memory access violation". This can be caused by anything from faulty RAM, to an incorrect/corrupt device driver, to poorly written/updated software and more commonly under Windows XP Service pack 2, malware/adware installations.
Usually you get this error message when performing a specific task, and if that happens you need to check the corresponding 3rd party's website/support department to see if they are aware of the problem. I doubt it is a Dreamweaver problem though, based on personal experience.
..a while back Symantec Antivirus caused the 0xC0000005 error with an additional message about a file called SAVRT.SYS . A simple software update to the Symantec Antivirus cured the problem.
0xC0000005 - Resolution Suggestion One:
In many cases this error has been generated by faulty RAM memory. So if you have just upgraded your computer with some new memory and you started getting this error then I would remove the new RAM and see if the error goes away. If it does then send the memory back and get a refund!
XP is on SP3 and you should really be running it.
If you don't have malware detection, get some, run a scan and clean it fromyour system.

Similar Messages

Since the Version 20.0 update when starting firefox I have frequently got the error message "firefox is having trouble your windows and tabs" .

Since the version 20.0 update when starting firefox I have frequently got the error message "firefox is having trouble recovering your windows and tabs" This has not occurred with previous versions. If I click on the box "restore" and close firefox the problem reoccurs if I click close I lose the bookmark sidebar. I am so sick and tired of these frequent and buggy updates (every one since 17.0 have caused norton 360 to stop detecting tracking cookies for several weeks and or broken the norton toolbar) that I will uninstall firefox and switch to another browser if this does not change.

See:
*http://kb.mozillazine.org/Firefox_crashes
*https://support.mozilla.org/kb/Firefox+crashes
If you have submitted crash reports then please post the IDs of one or more crash reports that have this format:
*bp-xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
You can find the IDs of the submitted crash reports on the about:crashes page.
*You can open the about:crashes page via the location bar, like you open a website.
See:
*http://kb.mozillazine.org/Mozilla_Crash_Reporter
*https://support.mozilla.org/kb/Mozilla+Crash+Reporter

Error messages when starting Dreamweaver

I keep getting a heap of error messages when I start Dreamweaver and although I've looked under the hood, I'm not sure how to *easily* sort them out.
Here's an image of the first message:
Unable to find file BL.htm in the Configuration/Floaters directory. The floater will not be shown.
This is followed by:
Unable to find file apElements.htm in the Configuration/Floaters directory. The floater will not be shown.
Unable to find file BusinessCatalyst.htm in the Configuration/Floaters directory. The floater will not be shown.
Unable to find file frames.htm in the Configuration/Floaters directory. The floater will not be shown.
Unable to find file btc.htm in the Configuration/Floaters directory. The floater will not be shown.
Unable to find file BL.htm in the Configuration/Floaters directory. The floater will not be shown.
Then once it is loaded, I get the following error message:
loadNewTypeError: Result of expression 'ftype' [undefined] is not an object.
After all that I can use the system.
Any help appreciated.

Please go to the following KB article and try #12:
http://helpx.adobe.com/dreamweaver/kb/troubleshoot-javascript-errors-dreamweaver-cs4.html

Error when starting Dreamweaver CS6 w/Web Assist Data Bridge installed

When I start Dreamweaver CS6 I get messages that it can't find the following files in the Configuration/floaters directory.
The Files are:
WA_Memento.htm
WA_Site Tools.htm
WA_Site Tools_Progress.htm
Then it says "The Floater will not be shown."
How do I fix this?

Resetting your workspace in Dreamweaver should resolve this. Click Window > Workspace Layout and reset.
If you owned older extensions, then installed Data Bridge, Dreamweaver is probably just trying to find the floaters the old extensions used. Should be a quick fix if you reset!

Error when starting Dreamweaver CC after first installation

I'm running CC under OS X 10.9. Having installed Dreamweaver CC as an admin-user using the CC Manager Dreamweaver doesn't start. The dreamweaver icon is shown in the OS X dock for a second, then disappears without starting dreamweaver.
Repairing the disk permissions won't help. Uninstalling an reinstalling Dreamweaver CC won't help.
Dreamweaver CS5 runs without problems, also Photoshop / Bridge / Premiere CC.
Thank you for any help!

Jeff A Wright, thank you for responding!
The Dreamweaver log file reports some errors like "Unable to delete directory "/Library/Application Support/Adobe/..." I assigned the necessary rights to this directory including all subdirectories: Dreamweaver starts and works fine!
I hope this will solve the InDesign problem as well; I'll try and report.

Dreamweaverhelper loads twice when starting Dreamweaver

Should Dreamweaverhelper.exe be loaded twice when launching Dreamweaver CC 2014? This is happening according to "Windows Task manager".
Is there a fix for this?

What version of SAP-GUI are you using ? SAP-GUI 7.2 (latest version) was heavily rewritten using Visual Studio and SAP has stated that certain features that existed in earlier SAP-GUI versions are no longer available (it's Microsoft's Fault). It is also quite possible that your initial launch macro in Excel is causing the problem.
I would personally recommend that you do NOT launch Bex Analyzer when Excel opens, unless this is your primary method to interact with Bex workbooks and such. That may resolve your issue.

Error 8 when starting the extracting the program-data load error:status 51

Dear all,
I am facing a data exracton problem while extracting data from SAP source system (Development Client 220). The scenario and related setting are as the flowings:
A. Setting:
We have created 2 source system one for the development and another for the quality in BW development client
1. BW server: SAP NetWeaver 2004s BI 7
PI_BASIS: 2005_1_700 Level: 12
SAP_BW: 700 Level:13
Source system (Development Client 220)
2. SAP ERP: SAP ERP Central Component 6.0
PI_BASIS: 2005_1_700 Level: 12
OS: SunOS
Source system (Quality Client 300)
2. SAP ERP: SAP ERP Central Component 6.0
PI_BASIS: 2005_1_700 Level: 12
OS: HP-UX
B. The scenario:
I was abele to load the Info provider from the Source system (Development Client 220), late we create another Source system (Quality Client 300) and abele to load the Info provider from that,
After creating the another Source system (Quality Client 300), initially I abele to load the info provider from both the Source system , but now I am unable to load the Info provider from the (Development Client 220),
Source system Creation:
For both 220 and 300, back ground user in source system is same with system type with same authorization (sap_all, sap_new, S_BI-WX_RFC) And user for source system to bw connection is dialog type (S_BI-WX_RFC, S_BI-WHM_RFC, SAP_ALL, SAP_NEW)
1: Now while at the Info Package : Start data load immediately and then get the
e-mail sent by user RFCUSER, and the content:
Error message from the source system
Diagnosis
An error occurred in the source system.
System Response
Caller 09 contains an error message.
Further analysis:
The error occurred in Service API .
2:Error in the detail tab of the call monitor as under,
bi data upload error:status 51 - error: Error 8 when starting the extracting the program 
Extraction (messages): Errors occurred
Error occurred in the data selection
Transfer (IDocs and TRFC): Errors occurred
Request IDoc : Application document not posted (red)
bw side: status 03: "IDoc: 0000000000007088 Status: Data passed to port OK,
 IDoc sent to SAP system or external program"
r/3 side: status 51: IDoc: 0000000000012140 Status: Application document not posted
 Error 8 when starting the extraction program
Info IDoc 1 : Application document posted (green)
 r/3 side: "IDoc: 0000000000012141 Status: Data passed to port OK
 IDoc sent to SAP system or external program"
 bw side: "IDoc: 0000000000007089 Status: Application document posted,
 IDoc was successfully transferred to the monitor updating"
Have attached screen shots showing error at BW side.
 check connection is ok, tried to restore the setting for bw-r3 connection though same problem
 Have checked partner profile.
what's wrong with the process? 
Best regards,
dushyant.

Hi,
 Refer note 140147.
Regards,
Meiy

Error when starting Firefox 3.6. "Javascript Application error. Invalid username/password combination. If you continue to get this error, try entering your email address as your username." Any suggestions on what to look for to resolve this?

When starting Mozilla Firefox 3.6, I get an error window which opens up additionally overtop my browser windows stating:
"Javascript Application"
followed with :
"Invalid username/password combination. If you continue to get this error, try entering your email address as your username."
Obviously it is happening with one of my email addresses/usernames & password combinations of which I know the username for (which I choose not to post here) and I'm not sure where to begin looking for a resolution to this problem.

I was able to resolve this by disabling (under Tools - Add-ons) Yahoo! Mail Notifier
Hope this helps some of you also!

Problem when starting up the Java Desktop System Release 3

Hi there,
I have used the Sun Solaris 10 x86 for while and I have found some problem that I don't know how to solve. So I am asking expert here for some help. Here is my error message:
<div class="pre"><pre>
Window 1:
There was an error starting the GNOME Settings Daemon.
Somethings, such as themes, sounds, or background settings may not work correctly.
The Settings Deamon restarted too many times.
GNOME will still try to restart the Settings Daemon next time you log in.
Window 2:
There was a problem registering the panel with the bonoboo - activation server.
The error code is: 3.
The panel now exit.
Wnidow 3:
Nautilus can't be used now, due to an unexpected error from Bonobo when attempting to register the file manager view server.
</pre></div>
The error messages show up sometimes but now all the time. Does anyone here have the solution for this? I'll appreciate every useful solutions. Thanks a lot!

I just removed the locales using the same tool and I can log in now.
Does anyone have any idea why this is or the correct way to install extra locales ?
Thanks

When starting FireFox, a message is displayed "script error" message related to Chrome - FireFox will not start regardless of the answer I select - how can I get FireFox to display so I can turn off all plug-ins? Safe Mode does the same thing.

This problem isn't on this system - but a system I support at our church.
When FireFox is started the first display is the message "A script on this page may be busy, or it may have stopped responding. You can stop the script now, or you can continue to see if the script will complete. Script: chrome://tavgp/content/libs/include.js:1101". There are two option buttons - Continue and Stop Script. Selecting either button closes that window - BUT the FireFox window is never displayed.

Do a clean reinstall and delete the Firefox program folder before (re)installing a fresh copy of the current Firefox release.
*Download the full Firefox installer and save the file to the desktop https://www.mozilla.org/en-US/firefox/all/
If possible uninstall your current Firefox version to cleanup the Windows registry and settings in security software.
*Do NOT remove "personal data" when you uninstall your current Firefox version, because this will remove all profile folders and you lose personal data like bookmarks and passwords including data in profiles created by other Firefox versions.
Remove the Firefox program folder before installing that newly downloaded copy of the Firefox installer.
*(32 bit Windows) "C:\Program Files\Mozilla Firefox\"
*(64 bit Windows) "C:\Program Files (x86)\Mozilla Firefox\"
*It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
*http://kb.mozillazine.org/Uninstalling_Firefox
Your bookmarks and other personal data are stored in the Firefox profile folder and won't be affected by an uninstall and (re)install, but make sure NOT to remove personal data when you uninstall Firefox as that will remove all Firefox profile folders and you lose your personal data.
If you keep having problems then also create a new profile.
*http://kb.mozillazine.org/Profile_folder_-_Firefox
*http://kb.mozillazine.org/Profile_backup
*http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

When starting Blend im getting a Shell32.dll error

Hello BB and his end users,
Yesterday i installed Blend on my Windows Vista Home Premium SP2.
When i start up Blend im getting this pop-up windows:
And when im click ok, i'm getting the Window:
I have try all kind of things: Roll-back to system restore point 01-08-2014, after that i did Windows Update, and restarted PC, then re downloaded Blend and installed it. Restart PC and same error pops up.
Please help me solve this issue, i don't know any more trics or tips to solve tis.
Regards Danny
Solved!
Go to Solution.

Hi!
If You read carefully this: http://global.blackberry.com/en/software/desktop/blackberry-blend.html You'll discover Blend supports PCs with Windows 7 or newer and BlackBerry devices Passport and P9983 only.
Your PC nor Your device from profile don't meet this requirements.

When starting Lirghtroom 5 I get the following error message each time: "Lightroom encountered an error when reading from its preview cache and needs to quit. Lightroom will attempt to fix this problem the next time it launches." It never launches.

Title says it all. Lightroom shuts down because it can't read from its preview cache.

Have a look at this thread the solution is there.
I get an error message when I open Lightroom

How to fix , when start the SQL Server Fulltext Search show error ?

show error : the request failed or the service did not respond in a timely fashion

Hi srajmuneer,
Please post the detail Windows Application Error Log regarding this issue for fur investigation. In addition, please also try to update "K10\Administrator" account password for SQL Server FullText Search service.
Hope this helps.
Regards,
Elvis Long
TechNet Community Support

"Business Catalyst" error message when starting Dw

Hello,
Since a yesterday, I have this error message (in french) when starting Dreamweaver.
"Lors de l'exécution de onload dans BusinessCatalyst.htm, la ou les erreurs Javascript suivante ont eu lieu - Dans le fichier "Business Catalyst : bcinit is not defined".
A few days ago, I started to have some errors message when opening any page of my website.
"Les traducteurs suivants n'ont pas été chargés à cause des erreurs :
ASP.htm : dispose d'informations de configuration invalides.
ColdFusion.htm : dispose d'informations de configuration invalides.
PHP_MySQL.htm : dispose d'informations de configuration invalides."
I've open an old website, those error messages still existing.
Does anybody have an idea ?
Thanks for your help.
Hugo

BC Status
Nancy O.

Memleak cannot work when start the management server by ctrlhandler.act

Hi, all
I use ctrlhandler.act to start a management server on running system. when start the memleak detector, i got the error message on server output:
[JRockit] ManagementServer started trend analysis
java.lang.NullPointerException
Continuing ...
java.lang.Exception: discarding statement XMLEncoder0.writeObject(HeapHistogram0);
Continuing ...
but when I started the management server with command line -Xmanagement. all is ok. What's the matter?
Thanks a lot!

Sorry, the jrocki version is 1.4.2_05 and 1.4.2_08.
And the os: windows XP professional and Redhat AD 7.2
And the weblogic server version is 'weblogic8.1 sp3'
any suggestion? Thank you!

When start Dreamweaver cs 5.5 system fatar error (c000021a) 0xc0000005

Similar Messages

Maybe you are looking for