When the inside edge bleed from facing pages is needed?

Hi I've been working on a magazine which is 130 pages and some brochure which is around 16 pages. May I know when I should give the value to the inside bleed and when should set it as 0? Thanks in advance!

Check with the printer, but it seems pretty unlikely you'll need an inside bleed for the brochures. You may well need one, though, on the magzine if it is going to be perfect bound. I think you probably are going to want to change that page count, too, to a multiple of 4.

Similar Messages

Print job best setup - inside edge bleed from facing pages?

I'm putting together a 32pp A4 report with InDesign CS3 that will be printed from PDF in China. I'm UK-based and I will be passing the file to the printers electronically. I speak no Chinese, yet my client has an office in China and one of their staff (non-graphics expert) will be the middle man.
At the moment I'm setting up my document with facing pages and 5mm bleed. I recall from a recent UK print job using the same document setup that when I output to PDF with Use Document Bleed Settings ticked, the print bureau complained that images which filled one side of A4 and bled off outside/top/bottom of the page did not bleed off the inside. I asked them how to give them what they needed and they said the facing spreads needed to be 'separated into single pages' before I made the PDF - this would enable bleed on all 4 sides. I didn't know how to do that and maintain facing pages to allow me to design on a spread-by-spread basis, so I asked them. They couldn't tell me, so I left it as it was. In the end they had to trim the pages slightly more on the inside to get rid of any white paper.
I'm very keen to avoid any problems at all with this print job, so I want to get the setup and process right in my head from the start.
So my question: how can I set this document up to minimise problems for the printer? I don't mind if that involves another process before exporting, I just don't know what that might be.
Many thanks.

The way you have it setup is the correct way for Perfect Binding.
The image that appears on the right hand page in the picture posted, that area actually goes into the spine area - look at any book that has a spine and see how deep the pages go into the spine.
You will also notice that the image on the right hand page does not go past the crop mark - so in reality it's actually cropped off the page altogether, so there's no need to worry about it.
What you have is perfect - for perfect binding (or saddle stitching)
Don't worry about the script posted earlier - that is for a different type of binding.
Sidenote
When you make a PDF for printing make sure you offset your Crop Marks further than your bleed
Bellow I've used points and pica (but you can use 5mm bleed and offset by 6mm)
Reason:
Crop marks
are needed to trim the page to size when printed. As printers can't
print right to edge of a sheet, and that it's near impossible to trim a
sheet of paper right to the edge of a colour - the colour needs to
extend past the crop line, this is called
bleed.
When you bleed the document, i.e., extend any item that is tucked right
against the foredge (the edges opposite the spine), then you need to
extend this object off the page into a "bleed" area.
This allows for human error when trimming the paper, as each sheet is
not trimmed individually (that would take forever!) they are stacked on
top of each other and trimmed in stacks. It would be impossible to stack
all the sheets exactly even, and there is movement on the press, so
compensating for the movement and the fact they can never be stacked
exactly even - for this reason you need objects to extend past the edge
of the page.
The crop marks
tell the guillotine operator where to trim the sheet. Once they have
the measurements in their guillotine machine it's a simple matter of
rinse and repeat with as many stacks of paper there are.
And printers can sometimes fold and trim a print job folding machine,
and since it's a machine and you have to account for mechanical errors
and human error, you need bleed too.
Bleed is important - If you don't add bleed then the object stops at the
foredge of the paper. And if the blade trims/crops close to the object
but misses by a sliver - then you have a sliver of white on the printed
piece, which is highly undesirable.
So you need crop marks
so the printers know where exactly to cut the paper, and to cut into
the bleed so that you don't have slivers of white.
And yes you need crop marks even if you don't have bleed, if you
don't have any bleed it's likely that the edges of the paper are just
white, so there are no markings where to cut to give the correct size
that you want. So crop marks need to be included no matter what.
And the placement of crop marks is important. As I said earlier, crop marks are
for letting the guillotine operator know where to trim the page so that
it cuts into the bleed area. The bleed area to allow for mechanical,
physical and human error. And seen as the bleed can sometimes be
included in a final printed piece it is not desirable to have anything
other than bleed objects in the bleed area.
For this reason you offset your crop marks to be outside the bleed area. As I'm in
Europe I work mainly in millimeters, so I would set my Bleed Area to be 5
mm and I would set my crop marks to Offset by 6mm.
This ensures that the crop marks do not encroach the bleed area. If your crop marks do
encroach the bleed area you run the risk of the crop
marks appearing on a final printed
piece.
So in Summary
Make sure you have bleed where necessary on your document.
Add the desired amount of bleed - in my case 5mm.
Offset the crop marks
so they don't encroach the bleed area - in my case 6mm.

Why the menu to move from one page to another is not seen when the page is online?

On my web, I have different pages like 'Homepage' or 'Contact' but when I publish my web I can not see the menu.
why the menu to move from one page to another is not seen when the page is online?
Thank you,
Roger.

Where are you publishing and how are you uploading the files?

I am writing a book and need to have the margins alternating left and right pages, so that there is sufficient margin for the binding. I have tried different inside and outside margins, the same inside and outside margins, facing pages, changing the maste

I am writing a book and need to have the margins alternating left and right pages, so that there is sufficient margin for the binding. I have tried different inside and outside margins, the same inside and outside margins, facing pages, changing the master, and I cannot get the margins to alternate at print time. The larger margin is always on the left. Can anyone please help me on this, as I have spent hours and lots of ink.

Set up as facing pages with a larger inside margin.

When I try to print from web page I get "printer not activated - error code 30", printer works on Internet Explorer

When I try to print from web page I get a dialogue box "Printer not activated - error code 30" followed by a dialogue box "An unknown error occurred while printing". The printer works on websites when I use Internet Explorer. Also, if I copy the web page and paste it into a Word document, I can print a copy. This issue just started this week; I have not encountered this problem prior to this week. Please advise.

What does that error message say?
See this: http://kb.mozillazine.org/Problems_printing_web_pages

Is there a way to play an mp4 file at the beginning of a published project only when the project is accessed from a specific site?

Is there a way to play an mp4 file at the beginning of a published project only when the project is accessed from a specific site?
A little background info. I use Captivate 7 and currently have over 100 projects that I maintain on a quarterly basis. I publish using the SWF format and upload the swf/htm files to a server where they are then accessed from a few locations (within our online documentation, in our software product, on two different websites). Many of the projects are linked so some will be viewed as a series and others viewed as a standalone video. Each video uses the same template and includes an intro and end slide. Now my organization wants to implement a new intro to all videos (those I publish and those from several groups across the organization). My current intros provide overview material for the specific video so the new intro, which is an animation with audio in mp4 format, would need to be placed at the start of each project. The issue is, the intro adds 9 seconds to every video and in many cases doesn’t add any value (say, if a user accesses the video from within our product or views the videos as a series). I’ve talked it over with my boss and we want to try to add the intro only to videos accessed from site X, not any other location. So now to my question. Is there a way to play an external mp4 file (intro) only when the published project is accessed from a specific site, therefore eliminating the need to update each project? Maybe there's a way to add a parameter or variable to the URL or the html code?
Thanks in advance for your suggestions. Please let me know if you need additional information.

AimeeLove,
I have a solution for you. You may have to modify the code a little bit based on how long the timeline animation is for your clock. I based mine on 3 seconds to complete a minute hand sweep around the clock.
Milliseconds for each point on the clock:
12 = 0
1 = 250
2 = 500
3 = 750
4 = 1000
5 = 1250
6 = 1500
7 = 1750
8 = 2000
9 = 2250
10 = 2500
11 = 2750
In the mouseover section for 12 o' clock, put this code...
myVar = setInterval(function(){
 var pos = sym.getPosition();
 if (pos > 0 && pos < 50){
 sym.stop(0);
 clearInterval(myVar);
},10);
When you point to the time, the setInterval method loops every 100th of a second and checks the current position of the timeline. When the timeline reaches the range between 0 and 50 milliseconds (almost impossible to hit 1 specific point), the timeline will stop at 0. Also, the clearInterval will be fired to stop the loop.
In the mouseout section, put this...
sym.play();
clearInterval(myVar);
It start the clock again, and it also clears the loop in case you mouseout before you reach the range.
Make sure that myVar is a global variable so you can clear it from the mouseout section.
Repeat this for each point on the clock. To avoid potential conflicts, you may want to use my12, my1, my2, etc. instead of myVar. I put the milliseconds at the top that you would use as the beginning of the range. 50 milliseconds should be enough to catch it. So, for 5 o' clock, you would make your range between 1250 and 1300.
Let me know if you have any questions. Thanks!
Fred

Short flickering when the notebook wakes up from sleep mode MacBook Pro Late 2013

Hello everyone!
I have a question concerning the display of my new MacBook Pro with retina display (late 2013).
Sometimes when opening the lid when the notebook wakes up from sleep mode, the display is flickering for like two seconds. Then everything is normal again.
This specially occurs when the lid has been closed for a longer time. It makes no difference if the power adapter is plugged in or not.
Have you experienced a similar flickering with your MacBook Pro?
Thank you in advance!

Hello!
I have the same problem with my late 2012 MacBook Pro Retina. The constant flickering after being awoken from sleep was a minor annoyance for me so I contacted Apple Support.
I shall explain what I have done thus far, and I recommend you follow the same steps as I did to tick off possible causes:
Firstly, I reset my PRAM (http://support.apple.com/kb/ph14222) and SMC (ttp://support.apple.com/kb/ht3964).
The issue still remained so I checked if the flickering occurred in a new user (if it does not then it points to your account having a setting which is causing the flickering - possibly third party). For me the flickering continued so I tested it in Safe Boot (which worked fine!).
I then ran (just to be certain) the Apple Hardware Test (http://support.apple.com/kb/ht1509). All seemed to be OK. So I reinstalled OS X and still the issue remained.
It was then I had an Apple Support person 'screen share' with me and we went through certain folders. My GPU folder had an unusual amount of files so we trashed them and began a restart however this led to a bigger problem; my notebook wouldn't boot (not even in Safe Boot!), so be very weary at this stage, I'm not sure if this was a rare case or we deleted something we shouldn't have. I then had to go into recovery mode to get back to square one.
Back to the initial problem I reinstalled a 'clean' OS X version from recovery mode; this was to determine whether if the data is corrupted on my account or if it's something else; most likely hardware by now even if there was nothing that came up in the hardware test (it won't account for everything). I checked from both a backup of my data and then from a fresh user after reinstalling OS X and still the flickering continued.
It was then a Senior Apple Support person set up an appointment to have my MacBook looked at and possibly repaired (it could be a minor wire causing the problem).
That is the point I am at now, so for my case it seems like a minor hardware problem. If your case is as similar as mine I recommend making an appointment with them to run more sophisticated hardware tests that your own MacBook would not run.
I will comment again when my issue is completely resolved for those who come across this Discussion in the future.
Hope this helps!

Does anyone know when the Mac Pro switched from ATA to SATA DVD Drives

Does anyone know when the Mac Pro switched from ATA to SATA DVD Drives ?
I tried to find this answer online but failed.

Appears the Mac Pro (Early 2008) is the last model to suggest Ultra ATA/100 optical.
And with an optional card, use Serial Attached SCSI via Mac Pro Raid.
This kind of information gets sketchy in that the hard drive bus and other parts are SATA
and only this (and earlier) model Mac Pro has optical drive interface w/ Ultra ATA/100. The
logic board on the early 2008 appears to have two Serial ATA ports, 3.0GBPS; so to check
these, you may need to look into specification in iFixit.com repair guides, any takeapart
guides, and note specifications in everymac.com and those from mactracker.ca.
The MacPro after Early 2008 model build series (Early 2009) appears to sport an optical
drive with 18x speed, compared to Early 2008 & before, whose drives indicate 16x spec.
Other changes may be indicated by certain parts and differences; processors, graphic
support, and those kinds of things. 2008 shows dual-core, afterward, quad-core.
So on what little I found, that would appear to be the divide or when optical drive spec
on the logic board changed from Ultra ATA/100 to SATA versions. But double check.
Good luck & happy computing!

Inside bleed on facing pages?

hi,
im creating a spiral bound booklet in cs4 i've set up master facing pages with my margins and grid, just wondering if it's possible to split the pages so that there is space between the pages to set up an inside bleed, but still remain in a spread layout so I can see how they look together?
elsewhere in the forums someone said there was a script to pull them apart but i couldn't find it, does someone have a link? and how stable would my pages be if I used it?
thanks

And this one
http://forums.adobe.com/message/2106000#2106000
See post 10 for a script to separate the pages for you

How come when i copy a color from one page to another, the color looks faded?

I'm using the same color in a multi-page layout. When i copy a color box from one page to another, the color looks faded on some pages. WHY?! Thanks!

So i checked the blend spaces - both are CMYK (as this doc will be offset printed). Something really strange is happening! See attach below: the 2 blues (same setup/blend space, color breakdown, etc...) look different! And my client is PICKY! ugh. HELP! Thanks again!

Question regarding bleeding and facing pages.

Hello,
i'm in trouble with my first InDesign document which is a 96 pages Magazine. It will be printed on A3 sheets stapled in the middle. My printing guy said that it's ok as A4 pages with 3mm bleed.
So now when i'm trying to export as a printed pdf (i check mark that i want to use the documents bleeding settings) it exports with sections from left and right depending on the pages (the left page exports with ?? i guess 3 mm ?? bleed from the right page and so on). If i override the bleeding settings and i set it to 0mm it all ok but i fear that some pictures or text might get cut off since i have all planned with the bleed markers in indesign.
And i can't uncheck the facing pages since i have some graphics (charts and so on) that spread from one page to another (on same spread).
My question is ... is there anything i can do and still use bleeds or (ignore "inside bleeds" or something) or is it ok to use the export as spreadsheet instead of individual pages since he wanted A4 pages?
Any help for a newbie would be appreciated. Thank you.

You should ask the printers to use PUR (polyurethane reactive) Bind when making a perfect bound book - that's a much stronger glue than EVA. It won't even break apart or fall apart going from freezing cold (out in the car over night) to being warmed up, which happens with EVA binding. But the PUR bind seems to be a lot more popular and stronger.
Failing that, getting the book threadsewn also helps to keep pages together. If you have a large print run and need these to last, then I suggest perfect binding them with a threadsewn finish.
I've definitely seen and done 96pp saddle stitched (well personally I have imposed, printed and delivered these). You might have to sacrafice a drop in weight on the body text. It can get ugly, but it's definitely doable.
My suggestion here would be to ask the printers for a similiar 96pp saddle stitch sample that they've done before, to make sure you're happy with it.
In fact, you can ask them to send you out a dummy (a blank version of the book trimmed and folded) to make sure you're happy with it.
It really is disppointing to get a printed job back from the printers and you discover you are not happy with the binding method.

The inline line object in the header is offset in facing pages. How can I make it align with the outer margin?

I have a Pages document with a header that contains both text and a line (a shape, inline) below the text. When I make the document two-sided (facing pages), with a 1" inside margin and a .75" outside margin, the line offsets either left or right in each section of the document. When a section starts with a right-hand page, the line is right justified on ALL the pages in the section (1" from the left and .75" from the right), even though it should be .75" from the LEFT on the LEFT-HAND pages. When a section starts with a left-hand page, the line is left justified on ALL the pages in the section.
Is there any way to get the header line to align with the margins properly in facing pages?

Hi Debra,
Click on Inspector > Layout > Section > Configuration
Is there a tick in 'Left and right pages are different'?
Please post a screen shot of your headers. That will help to show what you are trying to achieve.
To take a screen shot, hold down the shift and command keys, then type 4. The cursor will change to crosshairs. Release the shift and command keys. Drag over that part of your screen then release the mouse/trackpad. A screen shot will appear on your desktop. In a reply to a message, click on the camera icon in the Toolbar above your reply and
Choose File > Choose > Insert Image
You may have to try this twice. Camera icon sometimes needs a wake-up call, but works the second time.
Remove any personal details before taking the screen shot.
Regards,
Ian.

Print a line on the last or second from last page

I'm using Oracle Report 10.1.2.3.0.
I'd like to print a line on the last page of a report if the report has an odd number of pages or the second from last page of a report if the report has a even number of page. It is the later second from last requirement I'm struggling with. Can anyone help me solve this problem please?
The reason for this is that we are purchasing an envelope inserter that using Optical Mark Recognition (a series of lines on the side of the page). This only reads on the front side of a piece of paper, so when performing a duplex print the marks need to be on the odd page numbers. In this case I need to apply a mark on the front side of the last piece of paper.
Thanks

Hi InoL
Thank you for your response. I have seen similar solutions to this and have investigated them. Although they give you a work around to know the total number of pages in PLSQL, they only give you a way of knowing this once the report has completed formatting the last page. Unfortunately, my requirment is to know when I'm on the second from last page to perform some conditional formatting. I don't think knowing the total number of pages at this stage is going to be possible in reports, therefore I was hoping someone may know a "clever trick" to achieve this.
Thanks
Neil

Calling a method in the Custom ADF component from JSF page

HI.
I have created some custom compoents by extending the core ADF Components. Like i have a ComboBoxDefault component with it's ComboBoxDefaultTag.java and Controls.tld file.
Now my requirement is i want to bind my label to this component from the JSF page. like
<fwcontrols:label binding="#{listComponents.comboBoxDefaultLabel}" id="label1"/>
<fwcontrols:comboBoxDefault binding="#{listComponents.cmbLocales}"
value="en_GB" id="comboBoxDefault" autoSubmit="true" label="label1">
<f:selectItems value="#{listComponents.locales}"/>
</fwcontrols:comboBoxDefault>
In my JSF page the label will have an id, and that id will be specified in the label tag of the component.
In Tag.java file i have overrided the setProperty(FacesBean facesBean). In this method i have bind all my properties. In core JSF the setProperty method is provided with the UIComponent parameter, so i can call my method in component also. Which is not in case of ADF Faces.
My main point is how i can call my method setLabel() which is in ComboBoxDefault.java so that i can set the label.
Thanks in Advance.

Thanks for all your replies. I want this kind of a functionality because Im trying to invove a DC (Child DC) from a Parent DC such that the Child DC's view is displayed onto the view container of the Parent DC. I have embedded using 'interface view of a component instance' in the Parent Window and am able to create the component and set usage though the onPlugDefault of the Child View.
But I observe that when i make a call from the parent, the flow is like this:
1. The wdDoInit of the Child Component Controller gets triggered first.
2. Then the wdDoInit of the Child's VIEW gets triggered
3. and THEN the onPlugDefault of the Child Component Interface View
What I had actually wanted was to Fire onPlugDefault where Im calling a method LoadData(), after which the Child DC's view must be triggered so it can display the fetched data.
What is actually happening is the view gets displayed, but no data is displayed in the view.
Right now I have just given a work around where Im triggering LoadData() of the COmponent COntroller from the wdDoInit of the VIEW.
Is there a better way to do this? I find it strange that I have to load the Data from the view.
Thanks
Jack

How do I set inner bleeds for facing pages in Illustrator

I am designing the layout for a 8.5" x 8.5" children's book to be uploaded to an online publisher, and they require a .25" bleed around all the outside edges, except for a no ink area of .125" on the bind side. The document must be set up for single pages rather than spread. The document must be saved as postscript so I can create the pdf using Distiller (per the printer). How do I accomodate a different set of bleeds for facing (even/odd) pages within one Illustrator document?
Here are the guidlines I was given (this is the only image):
[IMG]http://img198.imageshack.us/img198/1604/xulontrimguide.jpg[/IMG]
Is this even possible? Or will I need to use InDesign? The document is already setup in Illustrator with an individual artboard for each page, and I'd rather not go through the hassle of transferring it all to InDesign. If I must, though, what is the best option for setting it up as an InDesign document, and how can I adjust these bleeds accordingly while retaining a singlepage pdf for saving as postscript?

Illustrator doesn't have a consept of facing pages, so you'll need InDesign to do that.

When the inside edge bleed from facing pages is needed?

Similar Messages

Maybe you are looking for