When using an Audio Interface...

Hey guys. I just purchased a Presonus AudioBox 44VSL to work with Logic so my drummer can hear the click track when my band plays live. I've been working on it for quite a while and I just had to ask; How do I make it so my drummer just hears the click track on one side of the headphones and synths on the other side? Thanks in advance!

You've got two options here:
1.) Keep the panned left & panned right setup you're using, but make sure the audio is being sent to the board into two separate channels: one for click, the other for the synths.  Then you can mute just the click track in the house but keep the click running to the drummer through an aux mix, and the synths channel can stay up in the house.
2.) Change the output of the click channel to another output on your device, i.e. Line Output 3, and send that audio to another channel on the PA mixer.  Each channel in Logic has the input and the output buttons stacked on top of each other just above the fader.  It's likely the output button on your Click track currently says "Stereo Out" or "Output 1&2".  Click on that and scroll down to Outputs, and then select the output of your choice (as long as your Audiobox is connected to the computer). 
Hope this helps!

Similar Messages

  • Feedback when using an Audio Interface

    Hello! I recently recorded some music with friends of mine. I am using an audio interface which I have a Mic and a guitar plugged into. So on the recording they sound crystal clear. Due to the fact the interface has only two lines in (MONO) I can not set up another mic for the drums. So I used the aggregate device through the MIDI and on garageband i record with the interface and the built in mic. Where I am encountering a problem is for the built in mic recording, it is also picking up the mic and guitar through the amp. I can't figure out how to filter it pre-recording, or take it away post-recording. Any help would be greatly appreciated!
    -Kevin C

    The mic will record everything it hears, no amount of filtering is going help much. If you already have a clean guitar and vocal track just delete the drum track and just record a new drum track using the Mic and interface. Make sure the drummer uses headphones to monitor the playback

  • Freezing anomalies and Error messages when using MOTU audio interface

    The following problem occurs when using my MOTU 828mk2 audio interface.
    The audio freezes up when playing back in Logic and any other time on the computer I'm attempting to play audio(internet, movie watching, etc.). I'm using a Mac Pro with 3gb ram. The program itself will often freeze up when attempting to play audio as well but works fine if the MOTU is turned off. The same thing goes for the internet and other programs. For instance, if I'm trying to listen to audio via the internet the page will freeze up and I most often wind up force quitting my browser.
    The problem has been getting worse but now audio will not play through the MOTU but for intermittent short second stints or so before the audio in any application freezes up(rainbow spin wheel).
    In Logic Express 7 this message first began to pop up:
    "Error while trying to synchronize audio and MIDI".
    This message is what pops up most often now:
    "Logic Express has detected a possible conflict between one or more third party MIDI or audio drivers. -Be sure to install the latest drivers for all audio and MIDI equipment connected to you computer, and remove any older or unused drivers."
    I have installed the recent Universal audio installer so I should be up to date with the MOTU driver but I don't know now about these, "third party drivers".
    I do have my MOTU install disk so I could remove everything and reinstall..? *Do I have to remove old drivers? If so, how do I do this?*
    NOTE: I had this same problem last year. For some reason I do not recall how it was resolved.

    This is still a major problem for me. Any recommendations?

  • MacBook with 10.6.2 drops audio when using firewire audio interface

    Hi there!
    I've got a problem that's getting a pretty big issue right now.
    It started when I first plugged in my newly bought Alesis Multimix 8 FireWire, at the moment running 10.5. After a while, the audio suddenly was gone, there was nothing. Unplugging and replugging the interface solved the problem, but it happened again, and again and again. I could also change the sample rate and the audio would come back. I hoped it was an issue with Leopard, so upgraded to Snow Leopard, but the problem is still there.
    At the moment I'm in the band for a musical, and it requiers a lot of different sounds, and I'm happy I found MainStage in the same box as Logic! Though with this audio dropout problem, it can't be a success. I borrowed a TC Electronic 24D from a friend hoping all troubles would be gone, but no, it's still there.
    Now, I can't figure out where the problem exist. Is the two different sound cards both failing? Is the MacBook hardware failing? Is OS X failing?
    I tried with different FW cables, but it didn't help. Could there be some bad stuff left from Leopard when I upgraded, I didn't do a clean install?

    I have a hard time believing it could be just OS X that's messing with us. If the problem came already in 10.5.3, following my logic, the bug should be gone by now.
    As you said, the easy fix is to use the built in headphone port, but in my case it doesn't work that good since there's some whining noise making itself clear when you amplify the signal.
    I've read somewhere that people have had success not plugging the interface directly to the Mac, but through a firewire hub of some kind, like an external harddrive. I will try that tomorrow.

  • When recording a video using quicktime and my built in camera (isight) how come the program wont let me use my audio interface rather than the built in mike?

    when recording a video using quicktime and my built in camera (isight) how come the program wont let me use my audio interface rather than the built in mike?

    when recording a video using quicktime and my built in camera (isight) how come the program wont let me use my audio interface rather than the built in mike?
    The basic answer is that Apple has not programmed the capture routine with this capability. As such, you can always send QT feedback requesting this feature be added as a future enhancement.

  • Recording using an audio interface or audio cable?

    Hi everyone,
    I am a newbie with Garageband and home recording in general and I just wanted some advice about the best way to record songs I have written on my Korg Triton Extreme synthesizer onto Garageband 09.
    So far I have been using a basic audio cable which is connected to my apple Imac from my Korg Triton Extreme synthesizer to copy the songs I have written on my Korg Triton Extreme synthesizer to Garageband and it sounds ok but I just wondered whether I should buy an audio interface and connect that to my Korg Triton Extreme synthersizer and my apple imac and Garageband and whether this would give me a significantly better quality recording of each song?
    All advice is welcome.
    Many thanks.

    You can record audio with a cheap cable for a few bucks or use an Audio Interface worth a couple of thousand bucks.
    Do you get a better quality for you money ... definately yes.
    Do you hear the difference ... it depends
    At the end, it comes down to your needs.
    In your case, you use a synthesizer that outputs line level. If you setup your level correctly (sending and receiving), then you might be ok and maybe not hear a difference with an expesive device. Even if you would hear a better sound in an A/B comparison, at the end it comes down to the following question: If you could hear only one solution (cheap or expensive) and you can't hear if it was recorded with the cheap or the expensive equipment then it doesn't matter.
    At the end, your money might be better spent on better speakers (that let you judge what you hear) or thrid party plugins that give you more production value.
    Recording a guitar signal or microphone - that is a completely different story.
    Hope that helps
    Edgar Rothermich
    http://DingDingMusic.com/Manuals/
    'I may receive some form of compensation, financial or otherwise, from my recommendation or link.'

  • Do you have to use an audio interface when you record a guitar with garageband on an iPad Air?

    I've been looking into getting an iPad Air through a new cell phone contract. The only reason I want it is so that I can start recording my own music. I don't want to have to buy an audio interface however, so I'm just wondering if I really need one.

    Josh, there really is no good way in and out of the iPad for recording audio without some sort of interface. There are a broad range available, some starting under $100.

  • No sound from internal speakers or headphones when using ART Tube interface

    Hi - can anyone help with this...
    I have no sound fromthe internal speakers or headphones when using my new ART Tube USB interface - I get a nice loud recording level from the ART but cant monitor - in Logic 7.2
    Audio hardware interface in logic 7.2 is set to USB Codec - just like the ART manual states
    And the SOUND control panel is set to speakers/headphones
    But no love...
    Any comments welcomed
    Si2

    By default, OSX will only let you have one interface active at any one time - so if you specify the ART as your interface to get sound in, you don't have access to your regular interface to listen to it.
    But there is a workaround - open the Audio/MIDI Setup utility, create a new "Aggregate Device", and add both your required audio interfaces to it.
    Now, back in Logic, select the aggregate device you created as the audio device, and now all your inputs and outputs from both interfaces are available - the aggregate device acts as one big interface containing both your hardware interfaces.

  • Monitoring and recording using my audio interface

    I am new to the logic express program. When I try to record with my audio interface (whether mic or instrument), do I always have to go to the "Device Input" settings and swithc the input to my interface? Even when I do that, the bars move indicating sound, but I cant hear it...dont know what I am doing wrong?
    So basically, right now, I record without being able to monitor, then when I want to hear it, I have to switch the device input back from the interface to the default device?
    It seems I am making this harder than it is.
    Thanks for the help.

    I am having the same problem (using a presonus firepod). Tried the aggregate solution but it is not working.
    Steps I took: Aggregate Device Editor > selected firepod and built-in output. Then in Audio Midi setup selected aggregate device as default input. In Logic Ex 8, preferences>audio>enabled core audio and selected aggregate device as the driver. Created a new track, tried using input monitoring and the record button. I can see the levels go up and down, so there is signal, but no sound for me to hear. The inputs and outputs for the track are input 1 outputs 1&2.
    So am I doing something wrong?
    Thanks guys.

  • Error while calling RFC when using BSP Web Interface

    Hi,
    we have a problem with the Authorization when we use an Web Interface for BSP. We have assigned all roles to the user which were mentioned in the SAP standard documentation:
    R_AREA   
    R_METHOD 
    R_PACKAGE
    R_PARAM  
    R_PLEVEL 
    R_PM_NAME
    R_PROFILE
    R_STS_PT 
    R_STS_SUP
    R_WEBITF 
    S_RS_ADMWB
    S_RS_AUTH
    S_RS_COMP
    S_RS_COMP1
    S_RS_DAS 
    S_RS_ICUBE
    but we still get the error message: "Error while calling RFC".
    When using a user with SAP_ALL, it works.
    What can we do?
    Thx for your time.
    Joerg

    Actually that's surprising - because BSP (Business Server Pages) and RFC (Remote Function Call) are not related; they use totally different transport protocols (http vs. RFC). Even if an BSP application is calling a function module remotely (acting as RFC client) no authorizations for S_RFC are required - in the calling system (but in the called system, i.e. the RFC server).
    Since assigning SAP_ALL seems to "cure" the problem, it seems to be an authorization issue, indeed. In that case it makes sense to use the authorization trace (ST01 - notice: that's specific to one single ABAP application server; you might have to activate the trace on multiple instances) to find out which authorizations are checked / demanded.

  • Using an audio interface with multiple inputs

    Hi,
    I'm currently facing an issue where I need to be able to use the audio from a microphone and a keyboard through Skype calling. I have them both plugged in to a Focusrite Saffire Pro 24 audio interface. The problem is that only the microphone plugged into input 1 seems to be coming through, as if Skype will only address one channel of the interface. Is there any way around this or a different method you have used in a similar situation?
    Thanks,

    I stumbled upon this thread in searching for some deeply hidden feature in Skype, but alas, there may not be a fix within Skype.  I realize the parent topic is very old, but I hope this can hope anyone in need of a solution (or get skype to incorporate some sort of summing feature).
    That being said, there is an alternative for those of us with interfaces that have fully customizable routing.  Fully customizable routing, and more than your standard two (stereo) outputs, and at least one more input than you need in total for microphones.
    What we're going to have to do for our podcast (one member is on vacation, states away), is hook all microphones into inputs that are not input 1. As far as I can tell, Skype will only recognize input 1.  In your interface's output routing software, you will need to create a submix/monitor mix (whatever they will call it) that sums (combines) all of the microphones together.  While you have the ability to add the software/daw return to this mix, you typically will not want to, as it could create feedback for the person joining the conversation via skype.
    After you have created this submix/monitor mix (and be sure to double/triple check that input 1 is not involved with this mix at all) you will assign this to an auxiliary output... so say, your interface has 4 outputs, assign it to output 3.  Then lead a cable from the physical output 3 into the physical input 1 on your interface.
    What this accomplishes is we're effectively sending all microphones into input 1, so your Skype recipient will be able to hear a mixdown of all microphones.  Certain interfaces will also allow you to do this routing without cabling.
    There are more things to keep in mind, like if you're recording the call, you'll want to run a parallel output from your Main DAW/Software return into another physical input, but again, quadruple-check that you are not monitoring that track into your main buss as it would create a horrible feedback loop.  Generally I'd have the caller record their audio through Audacity or something free, but getting their recording on my end makes for syncing the call to the room recording so much easier... SO MUCH.
    TL;DR
    1) Make sure you have more than 2 outputs, and 1 more input than you would normally need for mic's.
    2) Plug microphones into inputs 2 and on, saving input 1.
    3) Use interface's software/routing mixer to sum all microphone inputs (EXCEPT 1) to an unused physical output.
    4) Route or connect that output into Input 1.
    0-5) For the love of all audio gods, make sure you are double checking to avoid feedback.
    I also recognize that with the appearance of things like WavTap and Soundflower that there are other solutions -- but this is one option for those of us that do not wish to explore those options.

  • Security when using EM web interface to administer the database

    When I'm connecting to the database
    via EM Database Control web interface,
    it uses http protocol (http://machine:5500/em),
    can it be used for safety https protocol,
    or are there when using standard http protocol
    at least passwords encrypted before
    sending it over http?

    I have called
    'emctl secure dbconsole' command,
    it run successfully,
    but when I tried to start it
    'emctl start dbconsole', it failed,
    now I'm not able to stop it,
    when I do so, the output is like this
    '--- Failed to shutdown DBConsole Gracefully ---',
    the state is 'not running', but when I try to
    start it now it complains that EM Database Control
    is already running.
    What to do to make it work now at least without SSL?

  • STP won't use my audio interface for monitoring, but FCP will

    Hi, I've been using FCP for a long time, with my MOTU 896 audio interface (firewire). It works fine with FCP for monitoring the mix, playback, everything.
    Today, I decided to try STP for the first time (up until now, I've been doing all the audio within FCP). I cannot seem to get the MOTU to work for audio monitoring unless I change the System Sound Preferences to have the MOTU selected (and not the built-in line out).
    The STP Manual says that "by default, it will use the settings in the System Sound Prefs", but that you can change it. However, nothing I do seems to make any difference.
    - I set the Preferences:Recording tab to Monitor the MOTU 896.
    - In the Recording tab of the Inspector to Monitor the MOTU 896.
    But it still plays back through whatever is selected in the System Sound Panel. I can change this to the MOTU, but I would rather have my system sounds playing through the regular built-in line out.
    Am I missing a setting here? Thanks!
    (This is STP 1.1, on a Mac Pro Intel, running OS X 10.4.8.)
    MacPro Quad Core 3.0 Ghz / G4 Dual 800 QuickSilver / PBook G4 Titanium   Mac OS X (10.4.8)  

    Go to the AudioMidi Setup app and select the MOTU 896 as Default Output and built-in audio as System Output. That way, the system sounds will still use the built-in audio but STP will use the MOTU. Unfortunately, every other app (like iTunes or QuickTime) will use the MOTU as well. STP doesn't have any preferences to select its own interface like any other pro DAW out there. Maybe STP 2.0 will fix that?

  • Using external Audio interfaces with Windows XP on an iMac

    Does anybody know how to set the audio device used by this operating system running on an iMac to something other than Realtek HD? I have an Edirol Fa-101 audio interface that runs on my PC, and runs on my iMac perfectly.
    I have installed the drivers onto Windows XP Pro runing on my iMac using Boot Camp, but I am unable to set the input and output audio devices in the "Sounds and Audio Devices" panel to anything other than realtek HD. Anyone got any ideas?

    *"I have installed the drivers onto Windows XP Pro runing on my iMac using Boot Camp,"*
    You should probably then post your question in the Boot Camp discussions:
    http://discussions.apple.com/forum.jspa?forumID=1165

  • Nothing but line in/out trying to use firewire audio interface

    Hi all, hoping someone can help me out here. I just got and am trying to use a Behringer FAC202 firewire audio interface. It's documentation says all I have to do is plug it in and OS X is supposed to recognize it. Well it doesn't. I have no core audio control panel, and in the sound control panel all I have is the default line in/out for internal audio (I do have system sound through the built in sound card)
    Anyone have an idea why the firewire device isn't showing up? I did check the firewire bus and I see:
    Unknown Device:
    Manufacturer: Unknown
    Model: Unknown Device
    Maximum Speed: Up to 400 Mb/sec
    Connection Speed: Up to 400 Mb/sec
    The FAC202 is the only firewire device on the system.
    Any help would be most appreciated.
    Thanks.

    Thanks for your reply Jean,
    I did try that and saw no luck there either, but it actually turns out that the unit may well be defective. I tried it on several macs of various makes, as well as a couple of PCs and no joy all around, so I'm sending it back for replacement.
    Thanks again for your reply.
    Jeff

Maybe you are looking for