Where are temperature monitoring components on K9N Platinum?

Ok it appears that with current systems there is no mbrd mounted CPU temperature thermistor. There are two thermal sensors inside a K8 CPU: one is a simple thermal diode for use by external circuitry, e.g. a hardware monitor or Super I/O chip and this is the temperature you will see as measured through that monitor chip; the second is used internally by the CPU for software and hardware thermal management so includes the circuitry to translate to a temperature reading. This second sensor is associated with the THERMTRIP Status register where the diode measured "current temperature" is stored in bits 23-16 (23-14 for Rev G); now in pre-Rev F CPUs that field is documented as "reserved" but it does appear to have the temperature stored in it since Speedfan reads it and reports a valid(-looking) temperature. So with Speedfan you can get two CPU temperatures reported which behave somewhat differently, probably due to different calibrations of the sensor circuitry. One is read through the hardware monitor chip; the other is read directly from a CPU register.
What I'd like to know is if there is anything at all under the CoreCell box? In my system it is certainly not the Winbond hardware monitoring chip which is clearly visible in another area of the mbrd. Does anyone have a dead mbrd they could rip the CoreCell box off, just so we know what is hidden there?

Similar Messages

FIREPOD Where are my MONITORS?!?!?!

I have a powerbook g4 1.5 and i use a firpod, the mac reads the firepod and it records fine but the playback comes through my laptop speaker and not my monitors! the monitors are plugged in to the main cr output jack. please help me!!!! im using garageband right now until i get cubase in the mai;
thanks

At the top of the screen is a white MenuBar, to the far Left is the GarageBand menu (Technically it's called the Application Menu to be nonspecific to any particular app). Preferences for all Mac OS X Apps should be under this menu.

Where are the original components stored?

I want to look at the source of a component in library://ns.adobe.com/flex/spark, specifically the swfLoader. How can I find this?

In Flash Builder you can select the class name and hit F3 to view the source.
You can also look in [Flash Builder Install Directory]\sdks\[SDK Version]\frameworks\projects.
Or you can go here: http://opensource.adobe.com/svn/opensource/flex/sdk/

K9N Platinum - Wrong CPU Temperature in BIOS

Hi, I have a K9N Platinum (7250-020) with the latest 1.3 BIOS and an AMD X2 3800+. The CPU Temperature in the BIOS has a negative sign in front of it, and it seems to always report -48*C. I tried the latest nVidia nTune and it was reporting the CPU temperature to be 208*C, which is absolutely impossible...
Does anyone have the same problem? I searched around and it seems I'm not the only one, but I still cannot understand if it affects only some K9N Platinums or all...
Thanks.

Quote from: CBR600RR on 09-November-06, 06:51:56
I assume you are talking about checking voltages as reported by the BIOS in the HW Monitor page, not physically checking them with a multimeter, correct?
I'll take a look at the numbers in the BIOS, but last time I checked they were ok.
As for raising the issue with MSI, eventually I will, even if they ask you soooooo many questions (for good reasons, I know...) that it would take me half an hour to fill that form...
I've checked with both and software is a little out from what a multimeter state's. Only check with a multimeter if your happy to do so. http://forums.extremeoverclocking.com/showthread.php?t=137886 offer good advise if using a multimeter .....
The only issue I see is the AUX connector for 3.3v with ATX2.0 spec (Modular cables etc)
Quote
TheCleaner:
CAUTION: This test involves using probes with the computer ON. Please only do this if you feel competent enough to be dealing with electricity. If you short rails, you could risk damaging the PSU and possibly your components. I cannot be held responsible if something goes wrong, this is merely a guide. If you feel any concern, please post BEFORE doing this, and I will be glad to help.
Contacting MSI would be good to let them know of the problems your having

Where are configure files for Grid Control components?

I installed Grid Control 11g on Redhat 5.2, the repository database is Oracle 11.2.0.2 on the same box. It worked after installation, but after some weeks, I restart oms and got error [oracle@cchbi bin]$ ./emctl start oms
Oracle Enterprise Manager 11g Release 1 Grid Control
Copyright (c) 1996, 2010 Oracle Corporation. All rights reserved.
Starting WebTier...
WebTier Successfully Started
Starting Oracle Management Server...
Oracle Management Server is not functioning because of the following reason:
Connection to the repository failed. Verify that the repository connection information provided is correct.Tried to google and search the forum, the message is not very selective and got few relevant resut.
Hope your exterts can point me to the configure file where I can verify the connetion to repository. Alos some one would share with me the knowledge on the following topics
1) What are the processes/components of Grid Control ? I am aware of oms, opmn, and a process run as /u01/app/midware/oms11g/ccr/bin/nmz -cron –silent. ANy others? What are their functions?
2) Location of configure files, log files and binary executables of this processes/components.
Many thnaks.

Hi,
to check if the OMS is running properly execute the command "emctl status oms" ($OMS_HOME/bin).
The result should be "Oracle Management Server is up".
To check which components are currently running execute the command "opmnctl status" ($OMS_HOME/opmn/bin).
The result should be something like:
Processes in Instance: EnterpriseManager0.<host
-----------------------------------------------------------+---------
ias-component | process-type | pid | status
-----------------------------------------------------------+---------
DSA | DSA | N/A | Down
LogLoader | logloaderd | N/A | Down
HTTP_Server | HTTP_Server | 26470 | Alive
dcm-daemon | dcm-daemon | 26301 | Alive
OC4J | home | 1953 | Alive
OC4J | OC4J_EMPROV | 1954 | Alive
OC4J | OC4J_EM | 26523 | Alive
WebCache | WebCache | 27085 | Alive
WebCache | WebCacheAdmin | 27086 | Alive
Executing this command will answer your question whioch components need/should be up when using OEM/GC.
You will find some logfiles of the OMS under $OMS_HOME/sysman/log (e.g. emoms.trc, emoms.log). Please check logfile OC4J~OC4J_EM~default_island~1 under $OMS_HOME/opmn/logs as well...
To start the OMS you might try the command "opmnctl startall"...
HTH

K9N Platinum and Corsair CM2X1024-6400 **UPDATE - FIXED**

I'm trying to help a friend with their new K9N Platinum motherboard. We got everything installed successfully, but after getting into Windows, the machine will just freeze up randomly doing anything, software install, whatever, within a minute, or sometimes as long as 5 or more minutes.
Basic specs:
K9N Platinum motherboard
Flashed to BIOS version 1.4
AMD Athlon64 X2 3800+ (65W) socket AM2
BFG Geforce 7900GS
500W PCI-E power supply
Wester Digital 120GB 7200rpm SATA HD 8MB cache
Single 1GB stick of Corsair CM2X1024-6400 RAM (DDR2 800MHz) - Brand New - DIMM slot 1
Windows XP Professional with SP2 and all windows updates installed. (using IE6)
Installed all latest drivers from MSI's website for this board.
We tried 1st with DRAM timings on auto, then tried to set the timing manually according to Corsair's spec sheet for this module, including memory voltage at 1.9V.
We think it might be a bad memory module, because after getting into Windows, we run memtest, and errors are detected within the 1st minute. We have RMA'd the RAM module. I'm wondering though if we just didn't have the timing for the memory set correctly in the BIOS.
Is anyone here runnning this exact memory successfully, or is this board incompatible with this Corsair module? If you are running successfully, did you have to change the SPD timings manually, or are you running using the SPD Auto setting?
If you had to use manual setting, any help with the values to set in DRAM Timing would be greatly appreciated. As much detail as you can provide would be great. Thanks for your help.

Ok, still having major problem with running world of warcraft. This PC freezes/locks up in the game every single time within 5-10 minutes of play no matter what we've tried so far. This is not a shutdown or restart problem, just a freeze/lock-up symptom. I'm getting a bit frustrated at this point. No other problems in windows are encountered. We can work in windows with any other application, like adobe photoshop or any other software, with zero trouble. I'm beginning to think this is video card related somehow with this 7900 GS card.
For added info, the video card being used is this;
BFG Tech BFGR79256GSOCE GeForce 7900GS 256MB 256-bit GDDR3 PCI Express x16 Video Card
Chipset Manufacturer NVIDIA
GPU GeForce 7900GS
Core clock 525MHz(vs. 450MHz standard)
PixelPipelines 20
Memory Clock 1320MHz
Memory Size 256MB
Memory Interface 256-bit
Memory Type GDDR3
3D API
DirectX DirectX 9
OpenGL OpenGL 2.0
Ports - DVI 2
The mouse used is a logitech USB track ball mouse if that has any bearing on anything. No mouse troubles though, just thought I'd mention it.
Here's what we've tried so far;
Updated to BIOS version 1.4. This was done after the Windows XP install though, so not sure if something is hosed up here.
1) We set the RAM timings to 5-5-5-12-2T and 2.1Volts in BIOS manually, as per direct recommendation from Corsair.
1a) Ran memtest all night for about 9 hours straight and no errors at all detected. So I'm guessing this isn't a RAM problem really, but who knows .
2) Installed the Windows XP SP2 Hotfix for Dual Core Processors - hotfix KB896256
3) Installed the AMD Dual Core Optimizer from here -->http://www.amd.com/us-en/Processors/TechnicalResources/0,,30_182_871_13118,00.html
4) Updated the Nvidia system drivers with the nForce 550/570/570/590 SLI (C51+MCP55) driver package 9.19 WHQL from MSI's website here--> http://www.msi.com.tw/program/support/download/dld/spt_dld_detail.php?UID=730&kind=1
5) Currently running Nvidia video driver version --> ForceWare Release 90 Version: 93.71 Release Date: November 2, 2006 WHQL Certified.
6) Ran a complete Direct X diagnostics via dxdiag. All tests passed successfully.
7) Tried to install the AMD Athlon™ 64 X2 Dual Core Processor Driver for Windows XP and Windows Server 2003 Version (x86 and x64 exe) 1.3.2.16 from here -->http://www.amd.com/us-en/Processors/TechnicalResources/0,,30_182_871_13118,00.html
But it would NOT install because it says I have to first uninstall the current driver via add/remove programs, but it's not listed there, before installing this one. So, I have no idea where to look or how to do this, I'm afraid of messing up the processor driver. Can someone explain how to install this driver, and would not having this installed possibly be a potential cause of the game lock-ups?
I don't know what else to do. Could the version 9.19 Nvidia SATA or IDE drivers I installed be causing these game lock-up problems? If so, do I just go into device manager and just rollback drivers for all of the devices listed under the "IDE/ATA ATAPI Controllers" in device manager?
Again, this was a fresh windows XP Pro install on a newly formatted hard drive. Obviously something is fubar, but I'm running out of things to try. Maybe going into BIOS and "load optimized defaults" and start over?
Lastly, the tech specs on newegg.com for this video card say "A 350W PCI Express compliant system power supply (with 12V current rating of 22A or more)" is needed. Since the 500W power supply we're using has 2 separate 12V rails rated at 20A each, could this be the problem?? I'm open to suggestions. Thank you.

K9N Platinum Digital Coaxial Out

I am having an extreme amount of trouble with my K9N Platinum trying to get the SPDIF Digital Coaxial Out to work. In the Realtek HD Audio Manager the slider for SPDIF is not there; I'm not even able to adjust it. In the regular windows volume manager the slider is simply greyed out and immovable.
I have upgraded to what I believe are the latest Realtek HD drivers; directly from MSI's website as well as from the MSI Live Monitor.
I've poured over the options in the Realtek HD Audio Manager but I can't seem to find any way to fix this issue, as well as googled like crazy and searched this forum. I apologize if this is a duplicate topic; I did do a search and didn't find another one with a solution.
Any help on this would be greatly appreciated.

Quote from: palaios on 24-January-07, 01:54:40
Is it the realtek hd audio manager you are talking about?
If it is: When i boot my computer as usual and start realtek manager.. You usually see which outputs are in use in the top menu, I dont see the digital output (spdif optical) here, even when its connected. So i guess it cant be muted since the sound device is not recognized by my Operating System (Vista) and/or my motherboard (k9n nforce570 sli platinum)
When i plug a cable in the line-in output, the realtek manager responds and ads both the line-in button and the spidf (digital output) button in the top menu.
Yes, on my PC, with Windows XP (you're using Vista, things might be considerably different, I don't know), the Realtek HD Audio Manager under the Audio I/O tab has a setting for "DIGITAL": if you click on the little wrench icon next to it, you can select the Sampling Rate (from 44 to 192 kHz) and if you want to enable or not the SPDIF output. When enabled, the SPDIF port will output whatever sound you're playing, in its original format: if you play an MP3, it will be stereo, if you play a DVD with a Dolby AC3 5.1 audio stream (and you enable the SPDIF pass-through in your DVD software, like Nero Showtime), then it will be 5.1.
Based on my (little) experience, most games do NOT support a digital 5.1 output, so - even if you enable the "surround sound" in their settings - you will get only stereo sound from the SPDIF (you will get surround if you plug a 5.1 speaker system in the front/rear/center audio jacks on the MB). I read there are soundcards that can do digital 5.1 encoding on the fly, but that's a whole different story.
Hope this helps...

K9N Platinum, 7600GTOC, SLI, No Video Signal

Just built up my new system, specs as follows
MSI K9N Platinum
AMD 5200X2 AM2 CPU
2 Gigs Corsair XMS2 DDR800
2 BFG Tech 7600GT OC's in SLI
Thermaltake TR2-500 Watt PSU +12V(1) 14A +12V(2)15A
1 Maxtor 120 GB SATA 150
1 Maxtor 160 GB SATA 160
When i turned the computer on for the first time, the system boots up and there is one small beep, sounds like it is posting, but I get no video signal from my monitor, which I checked on my other computer and is working fine, I tried both video cards in the 1st slot, in non-sli mode and I get the same result each time, so I get no video signal with all ways tried? Do I not have enough power in this PSU to run what I have? The video manufacturer suggests a 450W PSU, which I meet, but do I not have enough juice the 12V rails? And would this cause the no signal? Any help would be much appreciated.

Hello, welcome to forum.
"When i turned the computer on for the first time, the system boots up and there is one small beep, sounds like it is posting, but I get no video signal from my monitor, which I checked on my other computer and is working fine, I tried both video cards in the 1st slot, in non-sli mode and I get the same result each time, so I get no video signal with all ways tried?"
have you tried with one of them only into 1st PCI-E? use 1st DVI output, when using SLI, ensure SLI bridge is configured property, connect monitor to VGA onto 1st PCI-E slot. also check monitor output is configured property(etc: Input 1, Input 2).
power down PC, remove power cord from the PSU and Clear CMOS Guide
re-test.
ensure all power cables are connected property. try to boot with one memory stick only into slot close to CPU socket.
what D-bracket shows?
"Do I not have enough power in this PSU to run what I have? The video manufacturer suggests a 450W PSU, which I meet, but do I not have enough juice the 12V rails? And would this cause the no signal?"
yes, think is too weak for your system
its recommended to get single rail with high amperes on +12V (over 30A)
read here:
PSU's---2 x 12v---The Dual Rail Myth
Is your problem caused by your PSU?
good suggestion can be found here:
https://forum-en.msi.com/index.php?topic=105635.msg783148#msg783148
https://forum-en.msi.com/index.php?topic=103299.msg757739#msg757739

K9N Platinum and BIOS flashing

New to MSI and this forum
I have a K9N Platinum which I've had some problems with and also need to flash the BIOS.
Problems are: Leadtek TV tuner card video problem watching TV (image and sound freezing) then my laser printer would not print through the parrallel port (works okay through a USB port).
Have had no real solutions from MSI with those two problems
Just recently I've come into owning a MSI 7950 GX2 video card.
Apparently this card won't work with the K9N unless I flash upgrade the BIOS (using A7250NMS, V1.20)
I know my way around computer hardware but BIOS flashing I've never done.
I'm using a NTFS file system,OS is WINXP SP1, processor AMD64 4800+ and HDD Hitachi 250GB SATA2
I have two choices to use these brand new video card:
1: Try to flash the BIOS (with the obvious risks involved)
2: Replace the K9N board with one that is compatible with the 7950 (bearing in mind the other problems with the K9N)
I've read artcles from this site and MSI about flashing using a NTFS file system and I'm not confident.
I know this post is between BIOS and motherboards so it was hard to decide where to place it.
If anyone has any thoughts on the best solution for this it would be appreciated

First of all , make sure you have a "fixedup" motherboard .
( the capacitor fix , see info in the "Post your K9N Ultra/Platinum (non SLI) 'Power Off' Issues Here (NForce 570 MCP)" thread)
https://forum-en.msi.com/index.php?topic=99924.0
Flash bios doesn't need to be done from HD .
You can have both afudos flash util and bios image file on a msdos bootable floppy diskette (verify it from windows with chkdsk A: /R )

K9n Platinum fan speed control

Hi!
I have the following configuration:
-Motherboard: MSI K9N Platinum v1.1
-Bios: AMI v1.3
-CPU: AMD Athlon 64 X2 Dual Core)
-CPU cooler: Artic Cooling Freezer 64 Pro
-Memory: Kingmax 2*1 GB
-Video card: MSI NX7600 GT
-Power Supply: Antec NeoHE430 430W
-Hard Drive: Samsung 250 GB SP2504C
-Operating system: Win XP Pro SP2
I would like to control the speed of the CPU fan automatically, according to the temperature.
I tried
-the Dual CoreCenter utility from MSI, but it allows me only check the speed manually (If I did not miss anything)
-control from BIOS HW Monitor setting SmartFan but it does not work at all. ( Iam not sure but this can be because my cooler, it has 3 pin connector, and th MB user guide tells it works only if I use 4 pin connector. Can you confirm this?)
-Speedfan 4.31, it seemed working, but the system become instabile. I check the programmers site, and this MB did not supported.
Do you have any suggesions, experience about controlling the CPUfan?
Thank you in advance!
T.

Thank you for the answers.
Unfortunately the smartfan feature is not working in my case.( set to 3-pin in BIOS) I asked the MSI Technical Support and they said:
As this motherboard includes 4 pins connector for cpu fan, the 4th pin is used to controlled cpu fan speed, if you use 3 pins fan, fan speed will not be changed automatically and smart fan will not function.
I feel a small contradiction here
Do you have other ideas other than smartfan and speedfan?
T.

K9N Platinum Problem

Hello,
I have a K9N Platinum 7250-020 and I read from a different forum to make a new thread about the shutdown issues since it said it wasn't affected. Funny thing is, I'm getting the same exact problem.
My specs:
CPU: AM2 4200+ (2.4ghz, memory is not overclocked because of the odd multiplier)
Motherboard: K9N Platinum bios 1.2 (tried several of them and they are all buggy!)
PSU: CoolerMaster iGreen series 500watt
Memory: Crucial Ballistix 2gb ddr2 800
Videocard: ATi x1950pro
Soundcard: Creative Audigy Platinum
Symptoms:
I will be listening to music thru winamp and then when I am installing a program it completely shuts off during the middle of installation.
I tried installing a game once from the cd-rom and then it immediately shuts down.
The funny thing of all of this, I never got a blue screen. So I know it can not be because of my Overclocking.
So thanks for reading, please repost if you have anything to report. I don't know when MSI will come out with bios 1.4 for this. I'm so angry...I do not know whether to return this or not. It would have to be through MSI..so yeah. Thanks again!

Well...this is weird..
Yeah I tried underclocking the bus (now keep in mind I have a AM2, 4200+, and it has an odd multiplier of 11x. Because of this the bus has to compensate with the memory, running at ddr2 800, by running it slightly lower. So if I were to run the bus at 200 MHz, then the memory would be around 366mhz. Thus, that leaves me some head room of overclocking just the CPU since the ram is specified to run at 400mhz.). It didn't help. So since I was running bios version 1.10, I though, "hey..why not update." And so I did to the latest. To my surprise the update description includes: -Improve memory compatibility. Funny, huh?
With that said, I updated and had the settings to what they're specified from Crucial for latency. Then I overclocked to 218 MHz. Thus, resulting a speed about 399.2 MHz for the memory. And to this very moment that I have been running two instances of Prime95, it has yet to come up with a fatal error.
Now like you said, BOSSKILLER, I checked the cpu temperature (with bios version 1.10) and it said like around 40C. Although, once I flashed to the latest version (with it being stable using via Prime95), now the cpu temp in the bios says something around -42C. And it gets better. Since I'm using 64 bit, MSI doesn't have their core center working for 64 bit (to my knowledge). So I decided to see what Everest Ultimate ed. would say. And here is the kicker. It gives a more logical reading for the CPU temp...+39C!
So yeah...lol.... It is working fine and dandy right now! But ehh...in the bios the auto-fan control wont work because the bios sees the cpu temp being negative and so the fan control wont adjust to it.
Anyway, thanks for helping me out again, BK! It's real nice having someone well...I don't know how to say exactly, but its just nice having someone to go to about my problems!
Thanks again!!!
P.S. Sorry about the long essay! :D

K9n platinum voltage question

Hello everyone,
I'm new to the boards and I hope someone can help me out.
Let me throw my specs out first:
mobo: msi k9n platinum 1.0 (bios 1.5) (ms-7250-20)
cpu: opteron 1212 (voltage should be 1.3/1.35)
ram: ocz 6400 platinum (5,5,5,15 2t) (2.1v)
gfx: evga 7800gt
ps: sunbeamtech 550w(+3.3v=28A, +5v=36A,+12v1=20A,+12v2=18A(30A/35*A))
This board does have the shut down problems, but I have done the work arounds and fixed 98% of them(memory timings were the most important to fix these)
My question is how do I set the volage for the cpu? I know go into the cell menu->cpu freq config->and change the voltage...but when I set it to 1.3~1.35, the cpu voltage in the H/W monitor & on the main cell menu page will show a .28 voltage increase. My cpu temps are also through the roof (35 idle/ 68+ load).
Right now I have my cpu voltage set at 1.25 and it seems mostly stable, but the cpu Vcore shows 1.528v in H/W monitor, and cell menu.
Also if I keep my voltage at 1.2 my temps are very low (20 idle/ 38 load)
When I use cpu-z it shows the voltage that I actually set.
Anyone have an answer or fix?
Thanks for any and all replies.

"My question is how do I set the volage for the cpu? I know go into the cell menu->cpu freq config->and change the voltage...but when I set it to 1.3~1.35, the cpu voltage in the H/W monitor & on the main cell menu page will show a .28 voltage increase. My cpu temps are also through the roof (35 idle/ 68+ load)."
leave CPU vid to Auto, you no need to change CPU vcore. voltage moving -/+ 0.05 is normal.
take care about CPU temp... your CPU is overheating and become instable, 68C+ is very high... re seat CPU ensure its mounted well, aplly new thermal paste, but do not put too much!! here are few wrong examples:
your under load temp should not exceed 55C. you may need to get better CPU cooler if no change.

K9N Platinum not booting up or showing any picture.

i had recently bought all my parts for a custom computer. i just received them 2 days ago. i got the k9n platinum motherbaord with an amd athlon 3800+ am2 cpu, ATi x1650 pro graphics card, Ultra 1024MB ddr2 533mhz ram, 320GB IDE hard drive, ide dvd burner, and a Raidmax Sagitta case.
the problem is i cant boot up into the bios screen. everytime i turn on the pc the monitor doesnt seem to show the computers there, just shows the amber light as if on sleep mode. first off i tried the mobo with just the cpu and graphics card, and still nothin. then the graphics card, cpu, and ram and no results. then just no ram, no cpu and no graphics card to test if the motherboard will give me a beep. i didnt get any beep whatsoever. i also tried this on multiple monitors and still no prevail.
any help would be appreciated

Quote from: charlie_fong on 10-November-06, 10:03:54
uhh how can i find out what the amps are? also im sure the ram isnt the problem since the motherboard doesnt even beep with or w/o memory... but who knows?? so i am somewhat narrowed down to the motherboard or the psu..
on the PSU sticker. (read +12V xx Ampers)
move your memory stick to the 1st orange slot DIMM3, close to the CPU socket.
remove power cord from the PSU, hit power button several time to drain caps electrify, touch with hands some metal for ES discharge, and Clear CMOS.
move jumper(JBAT1, green jumper near to the battery) to Clear Data position, wait 1 minute, then move jumper to the Keep Data position:
pull back power cord, ensure all power cables are connected to the mainboard.(24 ATX connector, 4pin JPW1, and 4pin HDD style JPW2) then turn on PC.
post back results.

K9N Platinum (not SLI) Ethernet/LAN ports shut down

Not sure if this has been up before but i could not find this exact problem. I have the K9N Platinum with am AMD 64x 4200+ CPU and OCZ 1GB x2 mem. My build and install of XP went without incident. My problem is that when I start to download anything of size, the LAN shut down. It will say "cable unplugged". If I switch to the second port, it will be good for a while, then the same thing. The only fix is to reboot. I am connected through a switch. I loaded the latest drivers (nVidia) from the monitor software. I found a different set on the NVidia web site and installed, but now it will not pick up DHCP. It will work if I hard code the IP. I read that it should be using Realtek drivers, not Nvidia. Please help!!! I opened a case with support but they have not answered yet.

That is a start on Specs. You can look at anyone's signatuires here to see what is most commonly looked for in specs. Your are missing the PSU specs.
However one of the first things to try is to go into Bios and set optimized defaults. Then you will need to make sure nothing else in Bios has changed as setting Optimized defaults usually changes things quite a bit.
Then make sure that your using the drivers that came with the board including the NVidia and Network drivers.
You may have to enter Device manager and remove the Network Driver and let it restart.
You did answer one question many folks would have with the specs you gave about memory. The memory you have listed should be fine.

Internal temperature monitoring utility?

Is there any monitoring software (similar to Activity Monitor) that detects whether key components such as the CPU and hard-drive are running at a reasonable temperature or are overheating?
I believe that temperature-monitoring sensors are present inside the casing so in theory what I am asking about should be possible.

Hi, KDS-KDS. My experience has been that temperature-reporting utilities such as the one linked by roam above (which I've tested) are only able to find a single sensor in my Tibook, the same generation as yours. That sensor watches only the hard drive, which is normally one of the cooler parts of a Tibook. Though there clearly are additional sensors in the machine, it appears that their output is unavailable to (or perhaps isn't readable by) such reporting software, for some reason. Owners of other Mac models have reported quite varied results, from highly satisfactory (several sensors detected) to no sensors detected at all.
This question came up several times in the Tibook discussion forums a while back, and my recollection is that no Tibook owner, regardless of which of the four generations his machine belonged to, ever found any temp-reporting software that could provide a readout on the CPU. If you do find one, please post in over there and let us know.

Where are temperature monitoring components on K9N Platinum?

Similar Messages

Maybe you are looking for