Where do I determine the current Firmware version that's installed?

Where do I determine the current Firmware version that's installed?
Thanks,
Kristin.

Firmware updates necessary (for OS X operation) for older Macs are available at Mac OS X: Available firmware updates
http://docs.info.apple.com/article.html?artnum=86117
 Cheers, Tom

Similar Messages

What is the current Firmware Verison that I should be using for my WRT110.....?

I am currently using 1.0.02....Is rhus the correct one....? If not, where do I get the new one....??

The Current Firmware version for your Router WRT110 is Ver.1.0.05 (Build 03)... Click on Download this firmware for your Router..
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Where Can I Find the Current SW Version?

Hi there.
There was a place on Nokia's website where I can check what the current version release is for a Nokia N95. That particular page asks me to enter the 7 digit product code. I swear, if I'm not looking for it, I see it. When I am, I can't.
Can someone send me the link for this web page?
Your help is appreciated!
Storm

here you go: http://europe.nokia.com/link?cid=EDITORIAL_528996
400.34.011
RM-244
Nokia E51

HT201364 Where do I find what the current OS version that is in my Mac Book ?

Where do I find the operating system that is currently loaded into my Mac Book?

Look under the Apple menu (upper left) and choose "About This Mac".

Where do I find the add-in READER that I installed in firefox?

I installed the READER in my browser. I get the message that the add-in is installed but cannot find it in any of the tabs (File, View, Tools, etc) and I cannot see any READER icon. How can I access it?
== I added Firefix READER

Are you talking about https://addons.mozilla.org/en-US/firefox/addon/184617/?src=api ? You need to contact the developer of the Extension directly.

How to determine GPIB-ENET firmware version?

I have several of the older GPIB-ENET units. I see the latest firmware binary on the FTP site is A5. I'm pretty sure our units have olders revs since they were installed several years ago. However the manual says to only update the firmware when necessary since there are a limited number of times the firmware can be updated.
My question: Is there a way to determine the device firmware version so I'm positive I need to update?
I notice the new EthernetConfig utility for GPIB-ENET/100 devices shows the firmware revision when you select the device. Can this utility also "see" older GPIB-ENET devices and show the firmware revision for these older devices as well?

Hi,
Could you email in to the technical support deparment? You can go to www.ni.com/ask. We'll try some alternatives.
DiegoF
National Instruments.

Determining the current viewId

Hi, I need to determine the current view id, therefore I am using the following code:
/* adf-settings.xml */
<adf-settings xmlns="http://xmlns.oracle.com/adf/settings">
<adfc-controller-config xmlns="http://xmlns.oracle.com/adf/controller/config">
    <lifecycle>
      <phase-listener>
        <listener-id>myPagePhaseListener</listener-id>
        <class>obasi.common.domain.myPagePhaseListener</class>
      </phase-listener>
    </lifecycle>
</adfc-controller-config>
</adf-settings>
/* myPagePhaseListener */
    public void beforePhase(PagePhaseEvent pagePhaseEvent) {
        try {
            if (pagePhaseEvent.getPhaseId() == Lifecycle.PREPARE_MODEL_ID) {
                for (Object child:FacesContext.getCurrentInstance().getViewRoot().getChildren())
                    if (child instanceof RichDocument)
                        System.out.println(FacesContext.getCurrentInstance().getViewRoot().getViewId());
        } catch (Exception ex)
            // ignore
    }But this doesn't seem to work accurately. Some viewId's are only "detected" after leaving a page...
I noticed that this happens when the URL inside my browser also remains pointing to the previous page.
Is there a way to solve this?
Thanks in advance,
Charles.

Hi,
Thanks for helping me out, Simon.
I am not sure about what changes should be made to my web.xml in order to not have the resources as view id's.
So here goes my web.xml - in the hope that you would be so kind to point me out where the problem lies.
<?xml version = '1.0' encoding = 'windows-1252'?>
<web-app xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd" version="2.5" xmlns="http://java.sun.com/xml/ns/javaee">
    <description>Empty web.xml file for Web Application</description>
    <context-param>
        <param-name>javax.faces.STATE_SAVING_METHOD</param-name>
        <param-value>client</param-value>
    </context-param>
    <context-param>
        <description>If this parameter is true, there will be an automatic check of the modification date of your JSPs, and saved state will be discarded when JSP's change. It will also automatically check if your skinning css files have changed without you having to restart the server. This makes development easier, but adds overhead. For this reason this parameter should be set to false when your application is deployed.</description>
        <param-name>org.apache.myfaces.trinidad.CHECK_FILE_MODIFICATION</param-name>
        <param-value>false</param-value>
    </context-param>
    <context-param>
        <param-name>RedirectToLogin</param-name>
        <param-value>login</param-value>
    </context-param>
    <context-param>
        <description>Whether the 'Generated by...' comment at the bottom of ADF Faces HTML pages should contain version number information.</description>
        <param-name>oracle.adf.view.rich.versionString.HIDDEN</param-name>
        <param-value>false</param-value>
    </context-param>
    <filter>
        <filter-name>JpsFilter</filter-name>
        <filter-class>oracle.security.jps.ee.http.JpsFilter</filter-class>
    </filter>
    <filter>
        <filter-name>trinidad</filter-name>
        <filter-class>org.apache.myfaces.trinidad.webapp.TrinidadFilter</filter-class>
    </filter>
    <filter>
        <filter-name>adfBindings</filter-name>

        <filter-class>obasi.instel.customlogin.DynamicJDBCBindingFilter</filter-class>
    </filter>
    <filter-mapping>
        <filter-name>JpsFilter</filter-name>
        <servlet-name>Faces Servlet</servlet-name>
        <dispatcher>FORWARD</dispatcher>
        <dispatcher>REQUEST</dispatcher>
        <dispatcher>INCLUDE</dispatcher>
    </filter-mapping>
    <filter-mapping>
        <filter-name>trinidad</filter-name>
        <servlet-name>Faces Servlet</servlet-name>
        <dispatcher>FORWARD</dispatcher>
        <dispatcher>REQUEST</dispatcher>
    </filter-mapping>
    <filter-mapping>
        <filter-name>adfBindings</filter-name>
        <servlet-name>Faces Servlet</servlet-name>
        <dispatcher>FORWARD</dispatcher>
        <dispatcher>REQUEST</dispatcher>
    </filter-mapping>
    <servlet>
        <servlet-name>Faces Servlet</servlet-name>
        <servlet-class>javax.faces.webapp.FacesServlet</servlet-class>
        <load-on-startup>1</load-on-startup>
    </servlet>
    <servlet>
        <servlet-name>resources</servlet-name>
        <servlet-class>org.apache.myfaces.trinidad.webapp.ResourceServlet</servlet-class>
    </servlet>
    <servlet-mapping>
        <servlet-name>Faces Servlet</servlet-name>
        <url-pattern>/faces/*</url-pattern>
    </servlet-mapping>
    <servlet-mapping>
        <servlet-name>resources</servlet-name>
        <url-pattern>/adf/*</url-pattern>
    </servlet-mapping>
    <servlet-mapping>
        <servlet-name>resources</servlet-name>
        <url-pattern>/afr/*</url-pattern>
    </servlet-mapping>
    <session-config>
        <session-timeout>35</session-timeout>
    </session-config>
    <mime-mapping>
        <extension>html</extension>
        <mime-type>text/html</mime-type>
    </mime-mapping>
    <mime-mapping>
        <extension>txt</extension>
        <mime-type>text/plain</mime-type>
    </mime-mapping>
</web-app>Please note that I am using Steve Muench's DynamicJDBCCredentials (http://radio.weblogs.com/0118231/stories/2004/09/23/notYetDocumentedAdfSampleApplications.html #129)

Where can I find the old firmware?

I was making some changes to my network when the utlity asked me to upgrade the firmware to 7.4.2. I did and now all I have is warm brick. I'm trying to figure out where I can download the 7.4.1 because currently the "download" just leads to an article.
http://support.apple.com/kb/HT3466

I found the answer on another forum (thank you to whoever posted that). Just in case someone else wonders the same thing.
1. Open AirPort Utility.
2. From the AirPort Utility menu, hold the Option key (Control key in Windows XP and Vista) and choose Check for Updates....
3. Select the specific firmware version you require.
4. Click Download.
5. Select your base station and choose Manual Setup from the Base Station menu, or double-click on the AWD icon.
6. Choose Base Station > Upload Firmware.
7. Select a firmware version and click OK.

Is every ios release overtakes the previous firmware version ?

Well I dont Know from where to start ....
I am using an Iphone 5 the problem is I am stuck in the recovery mode due to error 1 which is obviosly a hardware issue and most likely to be a baseband problem but here it is why am I asking this question because I was running ios 7.0.6 and suddenly the iphone became in ''Searching..." mode so tried the factory settings by erasing all data and settings but couldn't help so I went DFU mode and restored my iphone using 7.1 IPSW and Wizardry the iphone worked for just one day then the same problem ''Searching..'' .
So I went DFU mode again but this time I let itunes to update to the latest firmware version which is IOS 7.1.1 and then amazingly the phone worked for few hours but then again same problem '' Searching..." and BTW EVERY THING WORKING FINE EVEN WIFI EXCEPT THAT NO CALLS,TEXTS OR CELLULAR DATA AND THERE IS NO IMEI OR FIRMWARE.
So I went DFU for the third time but I got the error 1 alert message and Now I am stuck in Recovery mode.So .. Is that means that every IOS release over takes the previous firmware ... which means if I waited for the next IOS 7.1.2 or IOS 8 hopefully I will be able to get out from the recovery mode and run away from the error 1 alert monster ? ... and I know the problem searching might occur again but I think I might give up then for this handset then. But I want to try all the solutions and options I have in my hands since I got no AppleCare/Store in my Country

It is true that updates may potentially bring changes to some firmware as well as software, but not every thing changes in each update. If your hardware is failing compatibility with the current firmware, I would bet money that you are going to have issues with future versions as well. The iOS assumes that your hardware is in working order when it was designed and a failure in that hardware results in these errors and the inability to operate using the firmware. To assume that a different firmware (especially a future firmware update) will fix you issue is close to absurd, unless that firmware version made all iPhones (or even most) have hardware communication issues. Until that day, Apple is not going to alter the firmware. Also you stated that it worked then stopped multiple times and now you receive error 1, which during the update basically means the iPhone is not passing the hardware test, so even with a future update, the hardware is not going to pass the diagnostic test when installing firmware, therefore you will still need service.
Even if you have to send it off to a friend in the country of purchase, it's going to be better and faster than waiting on something that has a 1% chance of success.

Selective XML Index feature is not supported for the current database version , SQL Server Extended Events , Optimizing Reading from XML column datatype

Team , Thanks for looking into this ..
As a last resort on optimizing my stored procedure ( Below ) i wanted to create a Selective XML index ( Normal XML indexes doesn't seem to be improving performance as needed ) but i keep getting this error within my stored proc . Selective XML
Index feature is not supported for the current database version.. How ever
EXECUTE sys.sp_db_selective_xml_index; return 1 , stating Selective XML Indexes are enabled on my current database .
Is there ANY alternative way i can optimize below stored proc ?
Thanks in advance for your response(s) !
/****** Object: StoredProcedure [dbo].[MN_Process_DDLSchema_Changes] Script Date: 3/11/2015 3:10:42 PM ******/
SET ANSI_NULLS ON
GO
SET QUOTED_IDENTIFIER ON
GO
-- EXEC [dbo].[MN_Process_DDLSchema_Changes]
ALTER PROCEDURE [dbo].[MN_Process_DDLSchema_Changes]
AS
BEGIN
SET NOCOUNT ON --Does'nt have impact ( May be this wont on SQL Server Extended events session's being created on Server(s) , DB's )
SET TRANSACTION ISOLATION LEVEL READ UNCOMMITTED
select getdate() as getdate_0
DECLARE @XML XML , @Prev_Insertion_time DATETIME
-- Staging Previous Load time for filtering purpose ( Performance optimize while on insert )
SET @Prev_Insertion_time = (SELECT MAX(EE_Time_Stamp) FROM dbo.MN_DDLSchema_Changes_log ) -- Perf Optimize
-- PRINT '1'
CREATE TABLE #Temp
EventName VARCHAR(100),
Time_Stamp_EE DATETIME,
ObjectName VARCHAR(100),
ObjectType VARCHAR(100),
DbName VARCHAR(100),
ddl_Phase VARCHAR(50),
ClientAppName VARCHAR(2000),
ClientHostName VARCHAR(100),
server_instance_name VARCHAR(100),
ServerPrincipalName VARCHAR(100),
nt_username varchar(100),
SqlText NVARCHAR(MAX)
CREATE TABLE #XML_Hold
ID INT NOT NULL IDENTITY(1,1) PRIMARY KEY , -- PK necessity for Indexing on XML Col
BufferXml XML
select getdate() as getdate_01
INSERT INTO #XML_Hold (BufferXml)
SELECT
CAST(target_data AS XML) AS BufferXml -- Buffer Storage from SQL Extended Event(s) , Looks like there is a limitation with xml size ?? Need to re-search .
FROM sys.dm_xe_session_targets xet
INNER JOIN sys.dm_xe_sessions xes
ON xes.address = xet.event_session_address
WHERE xes.name = 'Capture DDL Schema Changes' --Ryelugu : 03/05/2015 Session being created withing SQL Server Extended Events
--RETURN
--SELECT * FROM #XML_Hold
select getdate() as getdate_1
-- 03/10/2015 RYelugu : Error while creating XML Index : Selective XML Index feature is not supported for the current database version
CREATE SELECTIVE XML INDEX SXI_TimeStamp ON #XML_Hold(BufferXml)
FOR
PathTimeStamp ='/RingBufferTarget/event/timestamp' AS XQUERY 'node()'
--RETURN
--CREATE PRIMARY XML INDEX [IX_XML_Hold] ON #XML_Hold(BufferXml) -- Ryelugu 03/09/2015 - Primary Index
--SELECT GETDATE() AS GETDATE_2
-- RYelugu 03/10/2015 -Creating secondary XML index doesnt make significant improvement at Query Optimizer , Instead creation takes more time , Only primary should be good here
--CREATE XML INDEX [IX_XML_Hold_values] ON #XML_Hold(BufferXml) -- Ryelugu 03/09/2015 - Primary Index , --There should exists a Primary for a secondary creation
--USING XML INDEX [IX_XML_Hold]
---- FOR VALUE
-- --FOR PROPERTY
-- FOR PATH
--SELECT GETDATE() AS GETDATE_3
--PRINT '2'
-- RETURN
SELECT GETDATE() GETDATE_3
INSERT INTO #Temp
EventName ,
Time_Stamp_EE ,
ObjectName ,
ObjectType,
DbName ,
ddl_Phase ,
ClientAppName ,
ClientHostName,
server_instance_name,
nt_username,
ServerPrincipalName ,
SqlText
SELECT
p.q.value('@name[1]','varchar(100)') AS eventname,
p.q.value('@timestamp[1]','datetime') AS timestampvalue,
p.q.value('(./data[@name="object_name"]/value)[1]','varchar(100)') AS objectname,
p.q.value('(./data[@name="object_type"]/text)[1]','varchar(100)') AS ObjectType,
p.q.value('(./action[@name="database_name"]/value)[1]','varchar(100)') AS databasename,
p.q.value('(./data[@name="ddl_phase"]/text)[1]','varchar(100)') AS ddl_phase,
p.q.value('(./action[@name="client_app_name"]/value)[1]','varchar(100)') AS clientappname,
p.q.value('(./action[@name="client_hostname"]/value)[1]','varchar(100)') AS clienthostname,
p.q.value('(./action[@name="server_instance_name"]/value)[1]','varchar(100)') AS server_instance_name,
p.q.value('(./action[@name="nt_username"]/value)[1]','varchar(100)') AS nt_username,
p.q.value('(./action[@name="server_principal_name"]/value)[1]','varchar(100)') AS serverprincipalname,
p.q.value('(./action[@name="sql_text"]/value)[1]','Nvarchar(max)') AS sqltext
FROM #XML_Hold
CROSS APPLY BufferXml.nodes('/RingBufferTarget/event')p(q)
WHERE -- Ryelugu 03/05/2015 - Perf Optimize - Filtering the Buffered XML so as not to lookup at previoulsy loaded records into stage table
p.q.value('@timestamp[1]','datetime') >= ISNULL(@Prev_Insertion_time ,p.q.value('@timestamp[1]','datetime'))
AND p.q.value('(./data[@name="ddl_phase"]/text)[1]','varchar(100)') ='Commit' --Ryelugu 03/06/2015 - Every Event records a begin version and a commit version into Buffer ( XML ) we need the committed version
AND p.q.value('(./data[@name="object_type"]/text)[1]','varchar(100)') <> 'STATISTICS' --Ryelugu 03/06/2015 - May be SQL Server Internally Creates Statistics for #Temp tables , we do not want Creation of STATISTICS Statement to be logged
AND p.q.value('(./data[@name="object_name"]/value)[1]','varchar(100)') NOT LIKE '%#%' -- Any stored proc which creates a temp table within it Extended Event does capture this creation statement SQL as well , we dont need it though
AND p.q.value('(./action[@name="client_app_name"]/value)[1]','varchar(100)') <> 'Replication Monitor' --Ryelugu : 03/09/2015 We do not want any records being caprutred by Replication Monitor ??
SELECT GETDATE() GETDATE_4
-- SELECT * FROM #TEMP
-- SELECT COUNT(*) FROM #TEMP
-- SELECT GETDATE()
-- RETURN
-- PRINT '3'
--RETURN
INSERT INTO [dbo].[MN_DDLSchema_Changes_log]
[UserName]
,[DbName]
,[ObjectName]
,[client_app_name]
,[ClientHostName]
,[ServerName]
,[SQL_TEXT]
,[EE_Time_Stamp]
,[Event_Name]
SELECT
CASE WHEN T.nt_username IS NULL OR LEN(T.nt_username) = 0 THEN t.ServerPrincipalName
ELSE T.nt_username
END
,T.DbName
,T.objectname
,T.clientappname
,t.ClientHostName
,T.server_instance_name
,T.sqltext
,T.Time_Stamp_EE
,T.eventname
FROM
#TEMP T
/** -- RYelugu 03/06/2015 - Filters are now being applied directly while retrieving records from BUFFER or on XML
-- Ryelugu 03/15/2015 - More filters are likely to be added on further testing
WHERE ddl_Phase ='Commit'
AND ObjectType <> 'STATISTICS' --Ryelugu 03/06/2015 - May be SQL Server Internally Creates Statistics for #Temp tables , we do not want Creation of STATISTICS Statement to be logged
AND ObjectName NOT LIKE '%#%' -- Any stored proc which creates a temp table within it Extended Event does capture this creation statement SQL as well , we dont need it though
AND T.Time_Stamp_EE >= @Prev_Insertion_time --Ryelugu 03/05/2015 - Performance Optimize
AND NOT EXISTS ( SELECT 1 FROM [dbo].[MN_DDLSchema_Changes_log] MN
WHERE MN.[ServerName] = T.server_instance_name -- Ryelugu Server Name needes to be added on to to xml ( Events in session )
AND MN.[DbName] = T.DbName
AND MN.[Event_Name] = T.EventName
AND MN.[ObjectName]= T.ObjectName
AND MN.[EE_Time_Stamp] = T.Time_Stamp_EE
AND MN.[SQL_TEXT] =T.SqlText -- Ryelugu 03/05/2015 This is a comparision Metric as well , But needs to decide on
-- Peformance Factor here , Will take advise from Lance if comparision on varchar(max) is a vital idea
--SELECT GETDATE()
--PRINT '4'
--RETURN
SELECT
top 100
[EE_Time_Stamp]
,[ServerName]
,[DbName]
,[Event_Name]
,[ObjectName]
,[UserName]
,[SQL_TEXT]
,[client_app_name]
,[Created_Date]
,[ClientHostName]
FROM
[dbo].[MN_DDLSchema_Changes_log]
ORDER BY [EE_Time_Stamp] desc
-- select getdate()
-- ** DELETE EVENTS after logging into Physical table
-- NEED TO Identify if this @XML can be updated into physical system table such that previously loaded events are left untoched
-- SET @XML.modify('delete /event/class/.[@timestamp="2015-03-06T13:01:19.020Z"]')
-- SELECT @XML
SELECT GETDATE() GETDATE_5
END
GO
Rajkumar Yelugu

@@Version : ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Microsoft SQL Server 2012 - 11.0.5058.0 (X64)
   May 14 2014 18:34:29
   Copyright (c) Microsoft Corporation
   Developer Edition (64-bit) on Windows NT 6.2 <X64> (Build 9200: ) (Hypervisor)
(1 row(s) affected)
Compatibility level is set to 110 .
One of the limitation states - XML columns with a depth of more than 128 nested nodes
How do i verify this ? Thanks .
Rajkumar Yelugu

How to determine the current update level of the system

How can we determine the current update level of the system. uname -a shows the release but how to obtain the update level through a program?
I have this sample program to display the version
#include <iostream>
#include <sys/utsname.h>
#include <dirent.h>
using namespace std;
int main()
struct utsname osinfo;
// Call uname to get system info, then extract strings.
uname(&osinfo);
if (osinfo.machine) {
    cout<<" Machine : "<< osinfo.machine;
if (osinfo.sysname) {
    cout << "\nOS Name : " << osinfo.sysname;
if (osinfo.release[0] != '\0') {
    cout<<"\nRelease : " << osinfo.release;
}My aim is to check if the Solaris box is 5.10 update 4 or not.
Edited by: nidhish9 on Nov 27, 2007 5:11 AM

nidhish9 wrote:
How can we determine the current update level of the system. uname -a shows the release but how to obtain the update level through a program?
I have this sample program to display the version
#include <iostream>
#include <sys/utsname.h>
#include <dirent.h>
using namespace std;
int main()
struct utsname osinfo;
// Call uname to get system info, then extract strings.
uname(&osinfo);
if (osinfo.machine) {
cout<<" Machine : "<< osinfo.machine;
if (osinfo.sysname) {
cout << "\nOS Name : " << osinfo.sysname;
if (osinfo.release[0] != '\0') {
cout<<"\nRelease : " << osinfo.release;
}My aim is to check if the Solaris box is 5.10 update 4 or not.
Edited by: nidhish9 on Nov 27, 2007 5:11 AMIt's in /etc/release...
essapd020-u004$ cat /etc/release
                       Solaris 10 8/07 s10s_u4wos_12b SPARC
           Copyright 2007 Sun Microsystems, Inc. All Rights Reserved.
                        Use is subject to license terms.
                            Assembled 16 August 2007
essapd020-u004$ It can be processed with some simple commands:
essapd020-u004$ cat /etc/release | head -1
                       Solaris 10 8/07 s10s_u4wos_12b SPARC
essapd020-u004$ cat /etc/release | head -1 | cut -f2 -d_ | cut -c1,2
u4
essapd020-u004$ Best,

What is the latest firmware version for iPod Photo?

I got a iPod Photo 60Gb and try to connect this to my Ice Link Gateway 500 in my car. It work fine on my other car using icelink but doesn't work with the new one. It say it does support iPod Photo. I wondering what version should it be on?.. I test other iPod Nano that work fine on it. I guessing it doesn't detect the gateway 500 as it automatic show up on iPod Nano screen. Where my iPod photo saying It is ok to disconnect.

What is the latest firmware version for iPod Photo?
1.2.1.

IWork Numbers -- how to determine the current selected column/row?

I am trying to write a script that grabs some text from a Numbers spreadsheet based on the selected field. I just can't figure how to actually get the column and row in a way I can use. Here's my start:
tell application "Numbers"
tell document 1
-- DETERMINE THE CURRENT SHEET
set currentsheetindex to 0
repeat with i from 1 to the count of sheets
tell sheet i
set x to the count of (tables whose selection range is not missing value)
end tell
if x is not 0 then
set the currentsheetindex to i
exit repeat
end if
end repeat
if the currentsheetindex is 0 then error "No sheet has a selected table."
-- GET THE VALUES OF THE SELECTED CELLS
tell sheet currentsheetindex
set the current_table to the first table whose selection range is not missing value
tell the current_table
set the range_values to the value of every cell of the selection range
set therange to every cell of the selection range
set thecol to column of first item of therange
set therow to row of first item of therange
end tell
end tell
end tell
end tell
It gives me a result like
row "30" of table "table" of sheet "sheet 1" of document "Scheduler.numbers" of application "Numbers"
but what I need is just "30" so I can use it for my scripts. I can't figure how to convert this to a string or some other useful format.
Can anyone help? I like Numbers but I always run into little problems like this, something I can't figure how to do, compared with other scriptable programs.

Search forGetSelParams or better for get_SelParams in the existing threads.
I posted this handler more than 30 times !
Yvan KOENIG (VALLAURIS, France) vendredi 18 mars 2011 17:03:05

Where can I find the enhancement package version in my sap system

Hi everybody,
Can anyone tell me where can I find the enhancement package version information in my sap system?
Thanks

Hi Mike
Thank you for your reply. But i can only find SAP BASIS7.1 under the Enterprise Services Repository in Tcode SPROXY.So could you tell where can I open SCV?
Thanks

Before using the current Mac version Yosemite, I did not have an Administrator password. It seems now that one is required to unlock and make changes in settings. I have tried all my usual passwords but to no avail. any ideas???

Before using the current Mac version Yosemite, I did not have an Administrator password. It seems now that one is required to unlock and make changes in settings. I have tried all my usual passwords but to no avail. any ideas???

Boot into Recovery. OS X: About OS X Recovery - Apple Support
Select Terminal from the Utilities menu.
At the prompt type,
resetpassword
Hit return.
Follow the prompts in the utility to select hard drive, then user.
Reset the password.
Exit the utility and restart.
You will need to log in with your new password, but your keychain will not be reset.
I’m not sure what access you’ll have to the old keychain since it didn’t have a password. You may be able to get into the keychain and reset the password to match your login password.

Where do I determine the current Firmware version that's installed?

Similar Messages

Maybe you are looking for