Where is check disk info on a x61s
Any machine I have ever run check disk on provides the results in the event manager under an application listing of WinLogIn 1001.
When I set checkdisk to run on a Lenovo, there is not a WinLogIn entry to be found.
There is a PerfLoad - but that does not contain the check disk info.
Where does Lenovo place the results of checkdisk?
Thanks.
Thanks for the reply. I checked the thread you pointed to.
This machine shows no entries for wininit, or winlogin. I checked the entire span of time during which we rebooted.
This was also true on a Lenovo laptop that is not having problems at this time.
To make matters worse, on the laptop that is having problems, if we are able to see an event log at all we can only view it quickly for as we scroll through it we get hit with a message that the events logs are corrupted and the window where the log resides goes blank.
We ended up running PC-Doctor... full test of the hard drive (the one that takes hours).. and there were no errors reported. Other hardware tests were also clear... so it appears to be a software issue.
So now I am trying to find out how to extract/obtain an XP install disk (We have the rescue and recovery image file, but no install CD) so we can slipstream SP3 so we can run sfc /scannow. Started another thread for that issue.
Similar Messages
-
Where is Check disk utility on itunes?
I am told that I have a corrupted itunes and need to run chkdsk utility. Having limited IT knowledge and getting no where with Add/Remove Programs under itunes, perhaps someone out there can help me. My itunes library is intact, however my ipod is empty and I've tried to reload with no success. I'm sure that once the corruption is repaired, that reloading will work. thanks
1)Enable Disk Mode on your iPod. See: Putting iPod into disk
mode.
2) Determine the drive letter of your iPod from My
Computer.
3) Go to Start, Run.
4) Type cmd. Hit Enter to take you to the Command
Prompt.
5) Type chkdsk /f X:, where X is the drive letter of
your iPod. Hit Enter, and any corrupt files are found
and corrected.
Reset the iPod to exit disk mode.
Thanks, have been trying, but hasn't worked, more corrupted errors showing up, such as
ipod_Control/iTunes/iTunesPrefs
iPod_Control/Music/FOI/JGDU.m4a
iPod_Control/iTunes/iTunes.DB
Lost, and it's very quiet without my iPod. Mi -
I purchased a IMac in Feb later I added a Seagate ext. hard drive. On April 29 I received an errors that the ext. Drive may be a read only and not backing up files. I'm unable to check disk permission or correct errors. Help would be appreciated.
Click on the hard drive on the desktop, then File > Get Info. What does it say about permissions? If this is just a data drive you may want to consider "ignore ownership on this volume".
Otherwise I can only say I have not been reading good things about Seagate drives recently. I have some of their rock-solid ones from about 10 years ago (still running well), but now...? -
After updating to ISO6, my email sending get extremely slow or dispeard. on the botton line of mail page always indicate "sending # of 9", however I do not know where to check or delete these unsent items. Please help! It has consumed lots of data.
I use @me.com and @hotmail.comHi,
>>A CHAR datatype and VARCHAR2 datatype are stored identically (eg: the word 'WORD' stored in a CHAR(4) and a varchar2(4) consume exactly the same amount of space on disk, both have leading byte counts).
Ok, but on the other hands:
SGMS@ORACLE10> create table x (name char(10), name2 varchar2(10));
Table created.
SGMS@ORACLE10> insert into x values ('hello','hello');
1 row created.
SGMS@ORACLE10> commit;
Commit complete.
SGMS@ORACLE10> select vsize(name),vsize(name2) from x;
VSIZE(NAME) VSIZE(NAME2)
10 5
SGMS@ORACLE10> select dump(name),dump(name2) from x;
DUMP(NAME) DUMP(NAME2)
Typ=96 Len=10: 104,101,108,108,111,32,32,32,32,32 Typ=1 Len=5: 104,101,108,108,111Cheers -
How and where to check Patch level in XI
Hi,
Can any one let me know how and where to check Patch level for XI systems.
Ex: 14SAPXIAFC17P_14.sca
Also pls provide me with the procedure for applying above patch.
ShavaliHi Shavali -
http://<host>:<j2ee_http_port>/sap/monitoring/ComponentInfo
also
http://<host>:<j2ee_http_port>/sap/monitoring/SystemInfo for core system info (J2EE or JVM patch level, etc.)
BTW, you need <i>SAP_J2EE_ADMIN</i> role for this.
Regards,
Jin -
Where can i get info that how many languages suppo...
Where can i get info that how many languages supported by default in Nokia phone?
If i buy it in UK,how?
Many thanks!
Solved!
Go to Solution.if you buy it in the UK, you would expect it to support your region's main languages or for Europe. for example, i am in asia-pacific region (australia) so the languages i have available to me are English, Pilipino, Tieng Viet and im guessing Japanase/chinese. so how many languages it supports depends on your region of course.
to check what languages are in your phone, goto Settings > PHone > Lanuage Settings> Phone Language (this is for S40 devices, no idea how to check in S60)
i hope this helps -
How/ where to check output type while saving sales order for confirmation
Hi All,
Could you anyone pls let me know How/ where to check output type while saving sales order for confirmation.
Present scenario : when the Sales Order is created the Order confirmation is sent irrespective of credit block of the sales order.
Requirement : Order confirmation ZA00 sent to the partner only for those Sales orders which does not have credit block and ZCLE sent to the partner if the order has credit block.
Now i want to know where exactly to check the output types "ZA00" and 'ZCLE' based on the credit block to send the confirmation to partener.
Quick help highly appreciated......
PreethamHi Santosh,
Thanks for the info. But here in this case I have to send the confiramation based on credit limit check. If credit limit check exceeds "ZCLE' should go as confirmation else 'ZA00' should go as confirmation.
Where can we check the credit limit whether it exceeded or not. My doubt is whether it is config issue or do we need to write code user exit or routine to send the specific output type for confirmation.
Thanks & Regards,
Preetham -
Ignore ownership box on disk info panel is missing.
I've lost one of my external disks and am using diskwarrior to attempt to rebuild the directory so I can move files off the drive. I'm on a macbook pro with tiger 10.4.8. Diskwarrior is version 4. After installing it when I try to run it errors out with an error about ownership not being sufficient in tiger and requests that I uncheck the ignore ownership box on the drive or the dmg (not sure which). In any case there is no ignore ownership box to uncheck on either device.
The device is a newly formatted boot device on which I freshly installed tiger. Neither the device nor the original disk in the macbook pro have this checkbox available. How can I restore the check box or how can I accomplish the same thing with another utility including chown or chmod?
thanks,
MikeThanks, I actually got by the ignore ownership problem. Someone elsewhere said that box shouldn't show up on the root/boot drive so I rebooted under the old boot and then looked at the newly inited boot device and there was the box. That got me past that problem. However now I can run disk warrior from a nonboot drive with the os installed but after agreeing to the license it fails with a message:
"An unserialized copy of Diskwarrior cannot be run from locked media, either restart
from the DiskWarrior disk cd or install disk warrior onto a hard disk."
There are lock checkboxes on the DiskWarrior DMG, the utilities folder and the applications folder in their respective disk info panels but they are all unchecked. There is no checkbox on the drive itself.I have no idea what this means and there are only two incidents of it on google neither of which are helpful. At this point I think I'm going to have to wait for alsoft Tech support.
thanks,
Mike -
Where have the disk usage pie charts gone in the activity monitor utility
Wherer have the disk usage pie charts gone?
>About This Mac>More Info
Click the Storage tab
They're bar graphs now. -
Hi,
I have to check disk space on remote servers..and alert us (send email) if free space goes below threshold value..Any ideas Please how to implement this using power shell...any help would be appreciated.
ThanksALL,
I was able to run this script with no problem
$percentWarning = 10;
# Get server list
$servers = Get-Content "$Env:USERPROFILE\serverlist.txt";
$datetime = Get-Date -Format "yyyyMMddHHmmss";
# Add headers to log file
Add-Content "$Env:USERPROFILE\server disks $datetime.txt" "server,deviceID,size,freespace,percentFree";
foreach($server in $servers)
# Get fixed drive info
$disks = Get-WmiObject -ComputerName $server -Class Win32_LogicalDisk -Filter "DriveType = 3";
foreach($disk in $disks)
$deviceID = $disk.DeviceID;
[float]$size = $disk.Size;
[float]$freespace = $disk.FreeSpace;
$percentFree = [Math]::Round(($freespace / $size)
* 100, 2);
$sizeGB = [Math]::Round($size / 1073741824, 2);
$freeSpaceGB = [Math]::Round($freespace / 1073741824,
2);
$colour = "Green";
if($percentFree -lt $percentWarning)
$colour = "Red";
Write-Host -ForegroundColor $colour "$server $deviceID
percentage free space = $percentFree";
Add-Content "$Env:USERPROFILE\server disks $datetime.txt"
"$server,$deviceID,$sizeGB,$freeSpaceGB,$percentFree";
Can you guys help me how to configure alerts here...like to sent email if $percentWarning goes below 10..
Thanks -
Get-SCStorageDisk cmdlet not returnig disk info
Hi,
We are using SCVMM cmdlet for storage provisioning needs. After provisioning the volume to one of the host in the cluster, I am not able to get that disk info on provisioned storage for a specific lun id.
ex power shell script: Get-SCStorageDisk | where { $_.SMLunId -eq $lunID}
If I rescan the disk in that cluster hosts and refresh the particular VMM cluster information, then this command is returning correct values.
I used get the value earlier without rescan. Is this known issue for this cmdlet.
is rescanning every host in the cluster is required to get the output in VMM cmdlet Get-SCStorageDisk ?
Thanks
ManoharaHi,
We are using SCVMM cmdlet for storage provisioning needs. After provisioning the volume to one of the host in the cluster, I am not able to get that disk info on provisioned storage for a specific lun id.
ex power shell script: Get-SCStorageDisk | where { $_.SMLunId -eq $lunID}
If I rescan the disk in that cluster hosts and refresh the particular VMM cluster information, then this command is returning correct values.
I used get the value earlier without rescan. Is this known issue for this cmdlet.
is rescanning every host in the cluster is required to get the output in VMM cmdlet Get-SCStorageDisk ? -
Hi... all,
What and where is the check disk utility?
I dropped my external 1T western digital and although I ran through this with the disk utility, It did this in a couple of mins...
On my PC this would have taken hours. Did it actually check all the sectors in that time? Or is there no sector checking?
AnitaI don't believe there is any built-in surface scan in any Mac OS X. If Disk Utility gave you a clean bill of health, you are probably fine. If you really want to do a surface scan, you can spend some money for TechTool Pro or DiskWarrior and check it that way.
-
I keep getting a message that some file on my ipod/itunes is corrupt. It tells me I should run the check disk utility. Some how it has wrecked everything! I have loaded almost 1000 songs into my nano and in itunes it shows my capacity as almost full in my ipod but when I try and see the music in my ipod its not there......WHAT DO I DO??????
iPod: What to do if Windows displays an "itunes.exe - Corrupt File" message
http://docs.info.apple.com/article.html?artnum=300554
Regards,
Colin R. -
Ran Windows 7 Check Disk on iPod - Songs Now Missing?
I posted this on another forum and didn`t get a response so I`ll ask it here:
Problem description: I connected my 80GB iPod Video to my netbook and Windows 7 came up asking me if I wanted to scan and fix problems on my iPod. I foolishly said okay and told it to, selecting both Automatically Fix File System Errors and Scan For and Attempt Recovery of Bad Sectors. It took about an hour to complete and afterwards when it connected in iTunes, it didn't recognize it despite recognizing it before check disk. I've connected it dozens of times to my netbook with no problems before today. iTunes began syncing (which it wasn't supposed to do) and freed up about 7GB of space on it before I realized what it was doing. Right now, in iTunes, Winamp and the iPod itself, no songs, videos, playlists or anything show up in it. iTunes claims 66GB is being taken up by "Other" with 7.5GB of "Free Space." Now, when I go into the iPod through windows explorer and go into the folder iPod_Control, all the music still seems to be there and I can listen to the songs in Winamp by opening them from iPod_Control, so why can't iTunes or the iPod find the files? Is there a good data recovery fix for this? Is there some hopefully easy fix I don't see?
Attempted fixes: Looked for iPod recovery programs, saw a trillion listed on Google of varying degrees of authenticity. Googled for ipod-related check disk problems and found a blog saying it erased his playcounts (oh no). Tried disconnecting and reconnecting iPod. Tried disconnecting, resetting and reconnecting iPod. Tried rebooting computer and reconnecting iPod. Tried connecting iPod to different computer it connected to before. Same story each time.
Recent changes: Windows 7 Check Disk, that's all I've done to it. It worked fine yesterday, last night and this morning until I ran Check Disk.
Operating system: 32-Bit Windows 7, evaluation copy, Build 7100.
System specs: Asus 1005HA: Intel Atom N280, 2GB Crucial Notebook Memory, Mobile Intel Express 945GME, 160GB HDD. iPod: Model MA448C, 5.5 Generation 80GB Video iPod, Software Version 1.3. iTunes Version 8.2.1.6
I have Googled and read the FAQ: Yes
What would cause this to happen? Why can't anything see the songs unless I manually open them? How do I fix this?After countless days trying to solve this problem, I feel I can now add to the few solutions presented on the various forums of the internet. I'll post here because 1: i'm a mac user for everyday life although like most have as many pc's as well. 2: I already have a login for these forums!
okay so i tried everything from re-burns to usb install (which I could not complete because removable drives are not recognized by xp and I don't have a vista system). The problem for me ended up being because the DVD drive was plugged into the primary master ide channel. My hard drive for the unit i was installing windows on is sata and was configured as such (not bridged into IDE channel by bios). So in a nutshell it seems like the hard drive and the DVD drive are nit picky in regards to the IDE configuration of the drives themselves. This won't help for virtualization on a mac pro I realize but nonetheless is food for thought hopefully for all the people searching for " windows 7 install cd/dvd device driver missing " in their search engine!
Oh boy one more reason to love mac's
Christos -
OraRRP Error with "Unable to copy data file;Error code 2, check disk space"
Hi,
Some users get this message -"Unable to copy data file;Error code 2, check disk space" when run report with orarrp, but most users do not get it.
I check free space at both server and client side, they are very sufficient.
I also checked directory exists for REPORTXX_TMP variable.
My user call reports via URL (rwservlet) and it occur for all reports.
How I can solve this problem?
Thanks in advance.
Tawatchai R.Hi,
have the same problem now. One user has temporarily problems to download .rrpa files via URL (rwservlet) request. Error code: -"Unable to copy data file;Error code 2, check disk space". Did you get a solution??
Thanks in advance. Axel
Maybe you are looking for
-
Bookmark 'Open in new Tab' or 'Window' doesn't on this latest install
Right clicking on a bookmark, allows me to open link in a new tab or window.... this works for the first while, but then breaks down and doesn't open anything. Restarting FF 4.0 works to resolve this issue. But lately after a half hour of working pro
-
Beginning Internet Sales R/3 Edition
Hi everybody! I'm about to start a project with Internet Sales R/3 Edition, and I can't find documents to know more about this product. Any help? Thanks in advance, Juan
-
How to find the columns and tables used in a stored procedure?
Hi, Can someone suggest how to find the columns and tables used within a stored procedure? Thanks VBK
-
Idoc error - Modify or delete Source List - any ideas experts PLZ?
Hi experts, I create a source list record by using Idoc with segments E1EORDH and E1EORDM the source list record is correctly created in database <u>=> the problem is when I try to modify or delete this source list record</u> <b>Error message (always
-
Key Figures not showing in BEx Workbooks
Hi, Recently we migrated the BW3.5 workbooks to BI7. After the migration and transportation of the workbooks to Quality system, in some of the workbooks the Key figures are not showing up and in some workbooks the key figures which are set as 'Hide"