Where is the 300 series switch with 48 gigabit ports and PoE?

Love the 300 series but surprised that Cisco did not put out a 48 port model with gigabit and PoE.  Would love to hear from Cisco on the reasoning behind that and if there are any plans to introduce one?  Given that gigabit and VoIP is the future at many companies it only makes sense.

The switches use the SFPs to link to each other. The SG500 has ports for 1G or 5G and the SG500X has 10G ports. Whichever port you select will be the speed at which the switches pass traffic and stack control information. These same ports can be 'reclaimed' if you were to set the switch to stand alone mode. I have put a chart below which details the ports you can use and the speed of these ports.
Header 1
Header 2
Header 3
Header 4
Header 5
Units in Stack
SG500X
SG500X
SG500
SG500
Stack Port Name
S1,S2-XG
S1,S2-5G
S1,S2
S3,S4
Stack Port Speeds
10G/1G
1G/5G
1G
1G/5G

Similar Messages

  • Cisco 300 series switches with 802.3at standard

    I'm a bit confused as to which of the 300 series switches supports the 802.3at standard. According to the website, the SG300-28P supports it. But in the quick start guide for the 300 series, only the MP models (excluding the SF302-08MP and SG300-10MP) including the SG300-52P has it. Can someone give me a difinitive answer to this? Thanks!

    LJ,
    P    = PoE capable. On the 300 series, half of the ports can provide 15.4W, or all can provide half that.
    PoE+ is NOT SUPPORTED.
    MP = Maximum Power. This means that all ports can provide up to 15.4W. PoE+ is supported on some models only.
    PP = PoE Plus. Can provide up to 30W on a single port. Note the maximum PoE budget for each switch. Also,
    half of the ports can provide 15.4W, or all can provide half that - any extra power used by PoE+
    MPP = Maximum Power and PoE Plus. This means that all ports can provide up to 15.4W - any extra power used by PoE+
    According to the Data Sheet:
    "Switches support 802.3at PoE+, 802.3af, and Cisco pre-standard (legacy) PoE. Maximum power of 30.0W to any 10/100 or Gigabit Ethernet port for PoE+ supported devices and 15.4W for PoE supported devices, until the PoE budget for the switch is reached"
    The PoE+ models are brand new and are not widey available yet. I did a web search for SG300-28PP and found that at least a few online resellers have it in stock.
    - Marty
    Message was edited by: Martin Pyhala

  • Are 300 Series switches compatible with pre-standard PoE detection in old Cisco phones?

    Are 300 Series switches compatible with pre-standard PoE detection in old Cisco phones? They don't seem to be (a 7902G won't power on when connected to an SF302-08MP with firmware version 1.1). Is any special configuration needed on the switch to enable this detection?

    Please note that the 200 and 300 Series switches now support Cisco Legacy POE as of September 2011, allowing it to deliver power to 7960, 7940, and other pre-standard phones and APs. Details provided at the following link:
    https://supportforums.cisco.com/docs/DOC-18337

  • Firmware upgrade question for 300 series switches

    Hi-
    I have a customer that is investigating a strategy and solution for centralized firmware management of the 300 series switches.  They have found an issue in the lab where they were trying to roll back the firmware to a previous version  They can not roll back to the previous firmware version, which is desirable in the case of finding an issue in the new firmware that causes them to have need to rollback to a known working version.
    We have read in the cisco 300 switch admin guide that there are two images (active and inactive) and that a new downloaded firmware always replaces the inactive image and is active until explicitly set.  The admin guide does not mention inability to make an older firmware image as active image when the switch has previously run on a new release firmware image.  My customer's engineers testing have informed me that an older image can not be made active after a newer image has booted.  Can you please verify if this if a fallback is supposed to work as it is causing a lot of concern-
    Thanks-
    Jena

    Jena,
    The release notes -
    http://www.cisco.com/en/US/docs/switches/lan/csbms/sf30x_sg30x/release_notes/Sx200-Sx300_R1.1.2.x.pdf
    What firmware is the switches currently on?
    Major Changes and Defects Corrected
    • Hardware version 1.0 devices that were upgraded to software version 1.1
    can now be downgraded to software version 1.0. You must delete the
    startup configuration file before rebooting the device to software version
    1.0. Otherwise the device may have problems when booting up. You may
    backup your running configuration before the reboot, and re-import the
    configuration afterward. Major Changes and Defects Corrected
    • Hardware version 1.0 devices that were upgraded to software version 1.1
    can now be downgraded to software version 1.0. You must delete the
    startup configuration file before rebooting the device to software version
    1.0. Otherwise the device may have problems when booting up. You may
    backup your running configuration before the reboot, and re-import the
    configuration afterward.
    Please read full release notes for other work arounds
    Hope this helps,
    Jasbryan

  • Using TACACS+ With ACS 5.6 on 300 Series Switches v1.4

    I was wondering if anyone could give me instructions on how to set up ACS for TACACS+ on a 300 series switch using Authorization? I can get it to work to authenticate, but the authorization doesn't seem to work like a catalyst switch. Thanks in advance for any help!

    Brandon, thanks for the link, but this is for the older software before they included authorization (the v1.4). I've looked through a bunch of manuals and tried to find examples online, but it doesn't seem like anyone has anything out there I can find.

  • CCA for 100 + 300 series switches?

    Is it in the roadmap to provide CCA control over 300 series switches?  We have a lot of SRW2008's put in before the 8-port ESW existed...and we have PITA vlan consistency issues out there too that I think CCA would help fix. 
    While I understand the "don't pre-announce products", I need a level of design intent around CCA - is it a tool for configuring UC series pieces primarily and all else is secondary? Or is it the multi-device config tool for all SBCS pieces?

    Nothing to do with the UC - primary concern is standalone networks.
    Real life case:
    2 ESW switches in control room hooked up to SA540
    Closet switches are SRW2008's
    Port no more than two devices are supposed to go now has 4, add an SRW2008 to the desk location.
    Now, it turns out that there is a badly behaved device at the desk - a video player that spews all sorts of traffic when it's playing that doesn't play nice with others.  So I now need to set-up a VLAN crossing those two switches. Oh, and it turns out the customer decided to unplug an access point and plug it into that switch too which ended up causing a loop when the PC plugged into ethernet someplace else attached to the PC.
    Tasks:
    Ensure that the 2 SRW2008's have proper vlan assignments to setup a port vlan for that video server.
    Issues:
    Make sure you assign proper configs to both ends of each link
    Make sure not to confuse one SRW2008 with another
    If new vlan, make sure all other ports that need to see it can still see it.
    Applications for CCA:
    Visualize all VLANS
    Document port assignments (i.e. where is the video server vs. printer on that last leg 2008)
    More easily see port statistics across multiple switches
    So after I did that work, I realized that the SA540 wasn't really up to being an aggregation switch too and made the ESW-540-48 into the aggregation switch which required some more changes - however CCA made it easy...
    At another job, I have SA540 + AP541ns (upgraded from RVL200 + WAP54GP's) but if I had 300 series in CCA, I'd upgrade the SRW2024's and SRW2008's but without easy management tools, the labor cost will be too high to make their networks really managed.....CCA makes that layer of management cheaper.

  • Cisco 300 series switches

    hi all
    Ive looked through some of the online content but dont see a definitive answer to my question about the physical size of the switches, are they all 19" rack mountable or desktop?
    I look forward to a confirmation..

    LJ,
    P    = PoE capable. On the 300 series, half of the ports can provide 15.4W, or all can provide half that.
    PoE+ is NOT SUPPORTED.
    MP = Maximum Power. This means that all ports can provide up to 15.4W. PoE+ is supported on some models only.
    PP = PoE Plus. Can provide up to 30W on a single port. Note the maximum PoE budget for each switch. Also,
    half of the ports can provide 15.4W, or all can provide half that - any extra power used by PoE+
    MPP = Maximum Power and PoE Plus. This means that all ports can provide up to 15.4W - any extra power used by PoE+
    According to the Data Sheet:
    "Switches support 802.3at PoE+, 802.3af, and Cisco pre-standard (legacy) PoE. Maximum power of 30.0W to any 10/100 or Gigabit Ethernet port for PoE+ supported devices and 15.4W for PoE supported devices, until the PoE budget for the switch is reached"
    The PoE+ models are brand new and are not widey available yet. I did a web search for SG300-28PP and found that at least a few online resellers have it in stock.
    - Marty
    Message was edited by: Martin Pyhala

  • Traceroute and Ping from GUI on 300 series switches?

    Any hopes of being able to do Pings and Traceroutes from the GUI? It's a little frustrating having to telnet/ssh to do those basic things.
    It would also be nice to be able to switch to Layer3 mode through the web GUI.

    Hi,
    Thank you for participating in the Small Business support community. My name is Nico Muselle from Cisco Sofia SBSC.
    With pleasure I can announce that the ping and traceroute function will be available in the next firmware release of the Sx300 series switches. Changing the system mode however is not (as far as I know).  The firmware to be release will contain major updates and addition of functions like TextView (command line interface), CDP, smartports, QinQ etc ...
    A little patience before this maintenance release is available, it will be certainly worth waiting for !
    Best regards,
    Nico Muselle
    Sr. Network Engineer - CCNA

  • TACACS+ Authorization on 300 Series Switches

    I was wondering if anyone could give me instructions on how to set up ACS for TACACS+ on a 300 series switch using Authorization? I can get it to work to authenticate, but the authorization doesn't seem to work like a catalyst switch. Thanks in advance for any help!

    Brandon, thanks for the link, but this is for the older software before they included authorization (the v1.4). I've looked through a bunch of manuals and tried to find examples online, but it doesn't seem like anyone has anything out there I can find.

  • I lost the pictures i took with my ipad2 and my vídeos, also my safe note, where can i find them??

    I LOST THE PICTURE I TOOK WITH MY IPAD2 AND MY VIDEOS, ALSO MY SAFE NOTES, WHERE CAN I FIND THEM????

    Had you reset your iPad or just done anything else when you found that they were missing ? If they were on the iPad when you last synced/backed up via your computer's iTunes then you could try restoring to that back up and see if that restores them to your iPad. Also for Notes you could check to see if they are stored on any of the email accounts that you've got on the iPad - try logging into the accounts via a browser and see if any have a Notes folder underneath them.

  • Where is the music library size with new itunes format?

    Where is the music library size with new itunes format that used to be at the bottom?

    Welcome to the Apple Support Communities
    Go to View > Show Status Bar

  • What's the password to logon the 3560 series switch on express setup

    what's the password to logon the 3560 series switch on express setup

    Hi Samuel,
    The 3560 doesn't have a password configured on it by default. You may want to double check the procedure for accessing Express Setup in case a step was missed:
    http://www.cisco.com/en/US/partner/docs/switches/lan/catalyst3560/hardware/quick/guide/3560gsg_08.html#wp49930
    If that still doesn't work, you can reset the switch to factory defaults by following this guide:
    http://www.cisco.com/en/US/partner/docs/switches/lan/catalyst3560/hardware/quick/guide/3560gsg_08.html#wp46478
    Hope that helps.
    -Mike

  • As a stockholder, I would like see the development of iTV with Retina display and integrating Siri control, internet access, and iTunes apps. This new product would be a large screen, thin wall mounted television, much like a oversided iPad.

    As a stockholder, I would like see the development of iTV with Retina display and integrating Siri control, internet access, and iTunes apps. This new product would be a large screen, thin wall mounted television, much like a oversided iPad.
    Do you think this product is possible?

    In general theory, one now has the Edit button for their posts, until someone/anyone Replies to it. I've had Edit available for weeks, as opposed to the old forum's ~ 30 mins.
    That, however, is in theory. I've posted, and immediately seen something that needed editing, only to find NO Replies, yet the Edit button is no longer available, only seconds later. Still, in that same thread, I'd have the Edit button from older posts, to which there had also been no Replies even after several days/weeks. Found one that had to be over a month old, and Edit was still there.
    Do not know the why/how of this behavior. At first, I thought that maybe there WAS a Reply, that "ate" my Edit button, but had not Refreshed on my screen. Refresh still showed no Replies, just no Edit either. In those cases, I just Reply and mention the [Edit].
    Also, it seems that the buttons get very scrambled at times, and Refresh does not always clear that up. I end up clicking where I "think" the right button should be and hope for the best. Seems that when the buttons do bunch up they can appear at random around the page, often three atop one another, and maybe one way the heck out in left-field.
    While I'm on a role, it would be nice to be able to switch between Flattened and Threaded Views on the fly. Each has a use, and having to go to Options and then come back down to the thread is a very slow process. Jive is probably incapable of this, but I can dream.
    Hunt

  • I bought a iphone 4 from a guy on craigslist, I knew about ios 7.0 having the lock thing, but when I met him, his simcard was in the phone, I tested the phone with his simcard in from of him. The phone looked great with no problems and I even got the box

    I bought a iphone 4 from a guy on craigslist, I knew about ios 7.0 having the lock thing, but when I met him, his simcard was in the phone, I tested the phone with his simcard in from of him. The phone looked great with no problems and I even got the box with the accesories, so I knew it was his... I then did the reset on the phone (erase all data... from settings) and it went through and activated and everything was good... I used the phone for about a month with no problems at all, even had my apple ID in the icloud and everything... well ios 7.0.6 came out and I used my computer to restore the phone, because I feel that the cord and computer gives it a better restore, it did great no problems, and when it went to the part where I went to activate the phone, I get a enter your apple id and password to complete activation... Wait... why is this up i thought, I thought I did everything like I suppose to to succesfully switch it to me, the new owner... but now its asking for some C******@yahoo.com.... I only have @gmail.com emails and none start with a C... The guy sold me the phone because he was switching to Verizon, and I tried to call him, and now the number is disconnected... I guess he switched to Verizon with a new number... Now im stuck with a paperweight that costed me $200.00... What can I do at this point... Please help me... I restored it to give it to my Step Son as I just got me the iphone 5... Thank you for ANY HELP in advance... Thank you again.

    I bought a iphone 4 from a guy on craigslist, I knew about ios 7.0 having the lock thing, but when I met him, his simcard was in the phone, I tested the phone with his simcard in from of him. The phone looked great with no problems and I even got the box with the accesories, so I knew it was his... I then did the reset on the phone (erase all data... from settings) and it went through and activated and everything was good... I used the phone for about a month with no problems at all, even had my apple ID in the icloud and everything... well ios 7.0.6 came out and I used my computer to restore the phone, because I feel that the cord and computer gives it a better restore, it did great no problems, and when it went to the part where I went to activate the phone, I get a enter your apple id and password to complete activation... Wait... why is this up i thought, I thought I did everything like I suppose to to succesfully switch it to me, the new owner... but now its asking for some C******@yahoo.com.... I only have @gmail.com emails and none start with a C... The guy sold me the phone because he was switching to Verizon, and I tried to call him, and now the number is disconnected... I guess he switched to Verizon with a new number... Now im stuck with a paperweight that costed me $200.00... What can I do at this point... Please help me... I restored it to give it to my Step Son as I just got me the iphone 5... Thank you for ANY HELP in advance... Thank you again.

  • What cable type for connecting with gigabit port

    What kind of lan cable that I should use for connecting with gigabit port from Time Capsule to get the fastest transfer rate. And what is the maximum rate MB/sec that could be?

    You can use CAT5 or CAT6.
    max transfer rate is:
    Fast Ethernet has a theoretical speed of 100 Mbits/sec (12 MB/sec), while Gigabit Ethernet has a theoretical speed of 1000 Mbits/sec (120 MB/sec). That suggests a double speed advantage of Gigabit Ethernet over USB (60 MB/sec), but neither protocol hits its maximum. In reality, a typical USB connected disk is roughly equal to or lesser than the throughput of a shared drive attached over a Gigabit Ethernet network.
    Over wireless network:
    - 802.11b has a theoretical speed maximum of 11 Mbits/sec with a typical transfer rate of around 4.5 Mbits/sec (0.5 MB/sec) with an ideal signal.
    - 802.11g has a theoretical speed maximum of 54 Mbits/sec, with a typical transfer rate of around 23 Mbits/sec (2.5 MB/sec) with an ideal signal.
    - 802.11n has a theoretical speed maximum of 300 Mbits/sec, with a typical transfer rate of around 74 Mbits/sec (9.25 MB/sec) with an ideal signal.

Maybe you are looking for