Where is the RSSI info between 1500 AP's?

Just wondering where in the WLC you can determine the signal strength between 2 1500's?

A good way to determine how well the 1500's are seeing each other is with the remote AP debugs. These will show you the SNR for an AP that is or isn't joined to the controller yet which is good in troubleshooting why a MAP won't join.
The commands to run them are:
debug ap enable
debug ap command dumpAdjs()

Similar Messages

I have my camera (Canon 5D MARK 2) set to take both JPEG Large and Raw files with each shot. I uploaded the images from the card to my Pro (Aperture 3) and while the import info said 1500 images were uploaded, I can't find the RAW images. Aperture put ab

I have my camera (Canon 5D Mark 2) set to take both JPEG Large and Raw files with each shot. I uploaded the images from the card to my Pro (Aperture 3) and while the import info said 1500 images were uploaded, I can't find the RAW images. Aperture put about 700 images in an untitled project folder, but all the images are the JPEGs. What am I missing?
Thanks,
upsjdris

Have you checked your "Import" settings for "Raw&Jpeg" pairs in the "Import" panel?
You can set Aperture to import raw, jpeg, or raw&jpeg.
If you imported Raw&Jpeg, but have set Aperture to use the Jpeg as original, you will see the imported image as Jpeg image, not as a raw image, even if the raw has also been imported. You can switch between Raw and Jpeg originals for selected images from the Photos menu:
Photos > Use Raw as original.
Regards
Léonie

Where's the song info on iTunes?

Hi!
Where's the "show info" button when you right-click on a song??? It would always say who the artist, composer etc. were...
Thanks!

I mean on iTunes Store...

Where is the summary info located for my device?

where is the summary info located on my ipod touch so I can change a setting?

If you have iTunes 11 turn on the Sidebar. Go to iTunes>View and click on Show Sidebar. You can also do a Crtl+S to show the sidebar. The sidebar is where Devices appears. and Control+B to show the Menu bar
Go to iTunes>Help>iTunes Help>Sync your iPod....>Overview

Where is the "Ratings" Info Stored?

I moved my music from an external 400GB drive to a new 750GB external drive.
My first issue was 30% of the links to my 66,000 songs were severed.
I had to re-build the song library by dropping my music back in to a blank iTunes Library. I then imported my former iTunes Library.xml document. My playlists came back but all the ratings info did not come over.
Where does iTunes store the ratings infomation?

I have much the same issue - a system failure, iTunes library restored by importing old 'iTunes Library.xml' file as recommended on this site, but I am left with no meta-data - in particular ratings. I still have backups of all the iTunes library files - how do I restore meta-data from them?
Thanks.

New Profile Layout - Where is the "Basic Info" Section?

The “Basic Info” section has been moved to the top of the profile, just below all contact actions and photos. Please refer to the below screenshot.

I have a problem to edit my profile. please tell me how to change my basic line is blocked

Hey where is the SHOW INFO?

On my iPod (mini) I could tap the center button on my click wheel and on the 3rd click the iPod would display the show description and details entered by the podcasters. How do I view/see this info on my iPhone? Anyone know?
Thanks

No, there isnt an option to see info or properties on individual files / songs / movies, etc. Whatever shows on the screen is what you get.
Make a suggestion here
http://www.apple.com/feedback/iphone.html
Its a good one.

Where does the banner info reside in the database

When you create a page and check display banner to on, you can edit the banner by adding links etc.
Does anyone know where the links are actually stored in the database ?
null

Hi Binosn,
Thanks for your interest and reply.
Wanted to know some more details regarding the document publisher.
How does the backend push the report to the Gateway, is there also a queue maintained in the backend system which processes the report requests asynchronously or the Gateway report publisher pulls them synchronously or is there any component necessary to be installed in the backend system for processing reports?
Is the document publisher feature a gateway feature or a Duet Enterprise specific feature?
Please suggest some material for further details if available.
Regards,
Avishek.

Where is the clip info now?

I need to find timestamp of individual events which multiple events have been downloaded into a particular folder.
The folder gives a date range of the "clips" but I dont know how to get each ones date.
I hate this new imovie

Click VIEW/SHOW SKIMMER INFO
Then you should see the date as you skim over the clips with your cursor.
Also, this may help.
VIEW/SHOW SEPARATE DAYS IN EVENTS

Where is the password info stored?

I have multiple computers and I also upgrade from time to time. This kludgey itunes store/itunes app/sync business is obnoxious. Now I notice I'm being queried for my password to authorize this computer. It works but... Where is this stored so I can bypass all this crap?

This may resolve your repeated authorization problems.
http://support.apple.com/kb/TS1389
Also, you seem to describe an iTunes issue not an iPad issue. Therefore, you might want to post in an iTunes forum.
Message was edited by: lllaass to add ref to iTunes forum

Where is the main difference between the GTX and Quadro cards?

I want to build a serious system for video editing/composing. I'll be using Pr, Sg, Ae (with Element) and 3ds max (just getting started). I read that the GTX card's specs are a lot higher, but the Quadros are recommended for editing and 3D apps. I was planning on integrating the K5000 and came across the much cheaper GTX Titan and lower cards. I also read through other discussions but am still confused. I won't use a 10-bit monitor. I do not plan on playing games on this computer. Just editing and composing. Most of all I'd like my render times to become a lot faster. And with the new Raw video for the 5D Mark III I will edit a lot of 2.2k raw footage. I want it to play smoothly without fps breakdowns even with effects apllied. Element will do some 3D stuff for me in AE. I'm thinking about getting more advanced in 3ds Max as well. What card would do the better job? I'm really not a computer nerd. I had a friend configure a system for me. This is what he came up with:
i7 3970x
32gb 2400mhz
512 SSD
WD Red in external raid
DX79 TO Intel Mainboard
Quadro K5000 (not sure about this one)
What configuration would work best and is expandable in the future?

Since I'm still trying to keep things mostly inexpensive...
Not with very much success, I must say.
Item
Component
Price
Alternative
Alternate
Price
Savings
1
i7-3970X
€ 910
i7-3930K
€ 510
€ 400
2
32 GB Kingston
Hyper X Beast
Will not work!!!
€ 300
64 GB G.Skill Ripjaws Z F3 2400
€ 580
-/- € 280
3
512 GB SSD
€ 400
128 GB Samsung 840 Pro SSD
€ 120
€ 280
4
DX79 TO mobo
€ 200
Asus P9-X79 Pro
€ 270
-/- € 70
5
Quadro K5000
€ 1820
GTX 770
€ 370
€ 1450
6
Storage solution
PM
Total
€ 3620
€ 1850
€ 1770
The only advantages of the 3970X are the higher standard clock speed, which loses all relevancy if you overclock, and the 15 MB L3 cache versus 12 MB L3, which has very limited value, especially when overclocking.
It is nonsense that 4 GB sticks are faster than 8 GB sticks, assuming the same timings. In both cases the slots are fully populated, so quad channel is fully used. Kingston Hyper X Beast will not work at all in a fully populated configuration, because it is 1.65V memory.
512 GB is a waste of space for OS & programs, 128 GB is more than enough.
Intel has a pretty lousy reputation with regards to overclockability and it misses two SATA 6G ports in comparison to the Asus.
The 770 is way faster than a K5000 for a fraction of the price.
The rest will only be about the storage solution, so read on.
Raid 1 doubles the price of your storage solution and gives no performance gain at all. The only connections you have available are 4 internal SATA 3G ports, one of which is in use for a BDR or DVD burner, which can not be reliably connected to a 6G port. Only three left. Mixing SATA 3G and 6G ports is always a bad idea when using raids.
External devices need a connection and you are quickly running out of SATA connections and then even (e)SATA is too slow for external storage when using raid arrays. Unless you want extremely costly solutions (think € 10K+) there is no sense in going external.
Why even consider a CPU like the i7-3970X and a K5000 card if the rest is so extremely underpowered? That makes no sense at all.
You need a lot of disks, you never have enough, but you need to rethink your raid solution. I give you something else to read: Adobe Community: To RAID or not to RAID, that is the question
With the basic components you chose above or with my alternative list, you have to consider a dedicated raid controller and many disks to make it work as you want.
Currently it looks like you want a Ferrari 599, but only with the gearbox of a Fiat 500. If you want to build a serious system, count on spending around 30 - 35% of the total budget on disks and another 10 - 15% on a dedicated raid controller. Then you will have much, much better performance, and security against disk failures.

Where do we maintain the copy control between sto (PO) to Delivery

Hi all,
Could please provide the info " where do we maintain the copy control between po and delivery "
.we have copy control between sale order & delivery so all so info will copy to delivery . like that where maintain the copy control between PO and delivery.??

Hi
I think we don't have any copy control like in sd,but we can maintain relation between delivery and po by po docuement type
see following path
spro-MM-purchasing-Purchase order-set up stock transfer order-assign delivery type and checking rule
and in same path define shipping data for plant
for Doc type NB - delivery type NL
for doc type UB-Delivery type-NLCC
Regards
Kailas Ugale

Where does the svc system get its infos from?

The longer I work with Solaris 10, the more I dread this awful "services" construction and its unwieldy administration.
I have a newly setup machine with two zones, one created right after the other, meaning they should be identical.
/usr is, as usual, lofs'ed into both zones, and contains a /usr/local/samba dir with a handcompiled 3.0.30 release.
I have not created any manifests as I intended to simply delete the 'onboard' samba service and start the new version
via the classical init script.
I boot both zones.. and one starts "/usr/local/samba/smbd -D -f /etc/smb.conf", and the other starts (or tries to) "/usr/sfw/sbin/smbd -D".
I inspected the manifest xmls for the network/samba service, and in both zones the entry lists /usr/sfw as start method.
svccfg listprop network/samba also reports /usr/sfw for both zones.
Where did the one zone get the info to start the /usr/local samba installation, and where did it get the (correct) conf file parameter?
Why does svccfg report a different startup method property than it really runs on svcadm enable?
I have grepped through all of /lib/svc, /etc/svc and /var/svc and nowhere is any reference to the /usr/local file nor the conf parameters.
Swapping the svc repository.db file between both zones also swaps the problem around - so it must be somewhere in there,
but as it's no longer a human readable file, I'm out of luck there. How did the /usr/local path and parameters get into that DB file?
Does the service system search the filesystem for known daemon binary names and other guesswork? And if it does such voodoo,
why didn't it do the same in the other identical zone?
rant Did we really need to get this svc "feature"? Until now I have seen no advantage from it, and only incurred a huge load of inconvenience,
be it the additional work of creating manifests for new services or debugging problems that I never had in a decade or two of init script usage.
We have all seen for many years how well this registry/service stuff worked on Windows..*/rant*

>
I boot both zones.. and one starts "/usr/local/samba/smbd -D -f /etc/smb.conf", and the other starts (or tries to) "/usr/sfw/sbin/smbd -D".
I inspected the manifest xmls for the network/samba service, and in both zones the entry lists /usr/sfw as start method.I take it you mean the full path with /usr/sfw in it, not "/usr/sfw" all by itself....
What do you get for:
svcprop -p start/exec network/samba:defaultThat should display the start string it uses.
Where did the one zone get the info to start the /usr/local samba installation, and where did it get the (correct) conf file parameter?I can only assume that some program inserted that string into the service. As you said, it's not in the manifest, so it didn't come from there.
Why does svccfg report a different startup method property than it really runs on svcadm enable?
I have grepped through all of /lib/svc, /etc/svc and /var/svc and nowhere is any reference to the /usr/local file nor the conf parameters.
Swapping the svc repository.db file between both zones also swaps the problem around - so it must be somewhere in there,
but as it's no longer a human readable file, I'm out of luck there. How did the /usr/local path and parameters get into that DB file?
Does the service system search the filesystem for known daemon binary names and other guesswork? And if it does such voodoo,
why didn't it do the same in the other identical zone?
rant Did we really need to get this svc "feature"? Until now I have seen no advantage from it, and only incurred a huge load of inconvenience,
be it the additional work of creating manifests for new services or debugging problems that I never had in a decade or two of init script usage.As with many such things, the advangages are greater when the environment is more complex. For starting a single job, you won't see the benefits as much.
Of course, the milestone services still run startup scripts out of /etc/rc[S23].d, so those are perfectly valid places to run a startup script.
Darren

I have backed up iphone where does the info go?

i have backed up my iphone where does the infromation go

I'm not sure what you're asking. The "info" is the data sync between your address book, calendar, etc so all that info is supposed to be synced between those apps on the BB and the Mac so the data is resident in those apps.

I migrated info from a hard drive to a new mac under time machine. It says I have shared files, but I don't see the old info on the new machine. Where do I look for it ? How do I make the old backup the base for my new macbook ?

I migrated info from a hard drive to a new mac under time machine. It says I have shared files, but I don't see the old info on the new machine. Where do I look for it ? How do I make the old backup the basis for my new macbook ?
The old OS was Mac X 10.5.8. I think the new one is 10.7.2 Lion.

Have a read here How do I set up a new Mac from an old one, its backups, or a PC?
Stefan

Where is the RSSI info between 1500 AP's?

Similar Messages

Maybe you are looking for