Where to download Cisco Spectrum Expert Connect (4.0 or greater)?

I downloaded the Wireless CleanAir Deployment Guide and on step 7, it stated:
On a Supported Windows platform with Cisco Spectrum Expert Connect (4.0 or greater) installed.
Where can I download Cisco Spectrum Expert Connect (4.0 or greater)?
We need to use it on our Upgraded WLC v7.0. Please kindly advice.
Thank You.
Junhan

Hi,
it will only officially be available early 2011 with the new release of WLC 7.0
However, there is a pre-Beta release and it seems ok to share with customers willing to try it out early.
No need to mention that you should not be complaining about bugs or any explosion induced by the beta software :-)
I'm attaching it here if you want to try the current version.
Nicolas
===
Don't forget to rate answers that you find useful

Similar Messages

Aironet 3500: Spectrum Expert Connect Mode

How do I connect to a 3500 to see the spectrum analysis? The manual says to download version 4.0 of the Cisco Spectrum Expert software but the latest verion is 3.3.52. What am I missing?
I want to get the most out of these new APs !!
Thanks,
Andrew

It is still Beta code. Not only do you need the Beta code, but a key
as well. After you have that installed, you log into your controller and
change the mode of your AP to SE-Connect and reboot the AP.
Then you go to the AP, copy another "key" from the AP and also
gather the IP address if it is DHCP.
You paste the key into your Spectrum Expert that is running on your
laptop, along with the IP address of the AP.
Then you can remotely see your spectrum.
I have done this before since I tested a 3500 for a few weeks before
sending it back to Cisco.
I'm impressed.. it is definately a nice feature.

Using Cisco spectrum expert can an AP(1131AG) work as a sensor?

We are thinking on buying the spectrum expert solution, but there is a good question. Can an AP 1131AG be settle as sensor?
Rds,
Alexandre

No not at this time. Only Spectrum Expert cards are supported. A future software upgrade will allow certain APs to be supported such as the 1242 and 1252 families. The 1130(1) will be end of lifed soon and replaced with the new 802.11n MIMO enabled 1140 series. I'm not sure if it will be supported or not.

Driver for Cisco Spectrum Expert Sensor WiFi

Hi
My company bought the above named sensor card. We have now tried on 4 different laptops, but we can't get it to work.
We have followed the instructions and installed the software before inserting the sensor card. The software version is 3.3.52. After installing, the software asked for a reboot of the laptop(s). We did, but after rebooting, Windows XP asks for a driver for "pci data acquisition and signaling processing controller". We have tried "googling" the driver, and also searched Cisco.com, without any luck. Can you help us?
...By the way. Our Windows XP are off course updated with SP3 and other updates.

I had a similar issue. Remove the card and then go to device manager and delete the network card from there. You may have gotten a windows driver loaded for it somehow. Then start the software and then re-insert the card. This fixed my problem. By the way, I love this product. I have found several issues with it. Leaky microwaves are my new enemy! I work at a hospital and I found a bad PCA pump killing wireless for the entire floor. Had Biomed replace it and my wireless problems went away. (for that floor anyway!)
Good luck!

Downloading Cisco ACS trial

hello,
i'm unable to find where to download Cisco ACS trial.
Thanks,
Omer Shtivi

Ok i managed to download the trial.
FYI
You download the full version and after you access throgh https you enter the Cisco Secure ACS License Registration
and downloading the demo license.

Power Density Measuring with Spectrum Expert

Hi All, does anyone have experiences with measuring of Power density S with the Cisco Spectrum Expert? I know that there is no direct way to do so, but is there a Formula or Algorithm to convert dBm in mW/squaremeter? I know that some of the Guys who makes their Money with that use the Rohde & Schwartz FSH 6 combined with a special calibrated Antenna and a simple Excel sheet for Conversion. Is such a Table available for Cicso Spectrum Expert with the delivered Antenna? Thanks for every Hint, Regards, Michael

No Idea anyone?

Where can I download the latest Webex Connect?

Dear Experts,
Where can I download the latest Webex Connect?
Hugo

Hi Hugo,
Check;
https://supportforums.cisco.com/thread/299844
Cheers!
Rob

Downloaded Cisco Connect for E1200 v2 disk image damaged. Now what? recent Mountain Lion upgrade

I had originally set up my E1200 Jan 2012 & had Cisco Connect setup. I didn't use it much but back in Oct after being away for 10 days I didn't have internet connection. Had to re-set both cable modem--then I at least had connection via ethernet, but still no wifi connection. Had to turn off for awhile to get it Router to properly reset & work. & then I think I had to do another reset maybe in Dec, can't remember exactly.
As I mention in another post, I have been having frequent intermittent not connected to internet messages for a long time. Usually if I just turn wifi off & then turn it back on it finds my network (although frequently I notice that it was on my guest network rather than main). I still don't know if it is cable modem, router or my ISP, altho they came out & checked & said signals ok, but modem could be going (Its old but about to move so don't want to buy new modem now).
I updated to Mountain Lion about 2-3 weeks ago.
After a Panic last night I was advised to make sure everything updated including router firmware.
When I opened Cisco Connect it said I had an unsupported Operating System. Trying to figure this all out, I finally found links to download Cisco Connect that are supposed to be compatible w Mountain Lion (at least the original link said that, but not where I went w the links so hoping it is right link for that). Anyway I downloaded it & was reading a bit & then clicket on the setup icon.
That said it was damaged & to eject it. I downloaded it via wifi just like I download other software. Maybe it is hyper sensitive so I need to take it over to plug directly into my cable modem? But then that will mess up the router, although I guess it will need to be reset any way.
So I think i need to get Cisco Connect updated so it works w Mountain Lion. Mountain Lion told me about 1 software that wasn't compatible but didn't pick up on Cisco Connect.
So don't know if I need to do a hard wired download, unlike the way I download other things, or what to get an undamaged copy. I then hope that it will see the old version, even though it isn't didn't work & hopefully pick up all my settings & all.
& then I guess I still need to check for a firmware update. & I understand that a firmware update should be done w a good connection (although the user manual just says good signal, web says hard wired ethernet. & because of the intermittent issues I plan to to it manually by 1st downloading & then installing from the download so there won't be a risk of interruption during install--if its even needed.
I'm running on a mid April 2010 13" MacBookPro
Any suggestions? This all is rather confusing.
Kathi

Well I was trying to update Cisco Connect so it would work w Mountain Lion but after 3 tries at the download I kept getting this same error message that it is downloaded. I even shut down & restarted before the last time w same result.
I should not have to spend hours of my time to get this to work. That is ridiculous.
Right before starting this process I checked for Apple updates & found a firmware update for my MacBookPro. I quickly downloaded & installed it, no problem. It took a very few minutes & then I backed it up & started working on this many hours ago.
I am an end user--not an IT professional. I just want things to work. I should not be expected to have to spend hours trying to figure out how to get stuff to work & still it doesn't. So I guess Linksys doesn't care that much about making things easy for Mac users.
I recently had the cable co come out & check the levels & all. they all checked out ok & they did change the fittings in several places on the coax connecters for good measure.
My cable modem is set up just across my living room from me & it is not a large living room. The router is right next to it, but it is not at a desk or place that is very comfortable to set up my Mac.
I sure hope that those security settings have been set up by default when I orginally set this up about a year ago. & I don't reall know how to change those settings without Cisco Connect, which I have been unable to get reinstalled since i keep getting those warnings about it being damaged.
I just want my computer devices to work. I don't want to have to spend hours troubleshooting them w poorly written instructions that don't really tell how to update firmware & Cisco Connect for tnose of us who have already had it set up before upgrading to Mountain Lion.
Having a link to download Cisco Connect that supposedly works w Mountain Lion but doesn't since it keeps giving a warning is not very helpful. There was nothing I saw in all my searches to tell what the results of even being able to upgrade Cisco Connect. Would it be able to figure existing settings? Didn't see anything that explained how that would work.
I don't appreciate my time being stolen by making it so hard to just get this updated! I"m giving up on this. I may try taking it back to Best Buy to see if they can tell if the router itself was also defective but I think I will likely go get an airport Express so I have a reliable router that is easy to use!
Kathi

I keep getting internet explorer cannot display web page when trying to download itunes. This only shows on half the page where the download link would be. My internet connection is fine.

I keep getting internet explorer cannot display web page when trying to download itunes. This only shows on half the page where the download link would be. My internet connection is fine. Any idea what the problem may be?

You won't see anything obviously related to iCloud, Jimmy. But if you go to the home iTunes Store page while logged into your iTunes Store account, you should see a Purchases link now under the Quick Links header. That's the only part of iCloud active at this time.
Regards.

From where can i download cisco "CCT Routing & Switching" free ebook

plz tell me that from where can i download cisco "CCT Routing & Switching" free ebook.thanks

If you mean this book:
http://www.amazon.com/Routing-Switching-Secrets-Successful-Certified/dp/148615980X
If it not free. Looks like it may have been freely distributed at one time, but is not anymore.
Based on the Amazon reviews, the book is not very valuable.
You are better off using resources from http://learningnetwork.cisco.com.

Spectrum Expert - USB or Express Card

The Spectrum Expert is a great tool but the problem is to find a notebook with a PC-Card / PCMCIA slot.
I know that there are adapters available for EC to PC-Card but I think this is not a solution for customers.
I didn't find any information on the Cisco website about an alternative.
Question: When will be a Spectrum Expert Card available with USB or EC connector?

Hi Irina and Scott,
I know the AP SE-Connect feature but we need a portable solution.
Cisco should think about a USB or Express Card solution.
The APs are working with the Spectrum Expert and it will be hard to explain to a customer that he should use a 3rd party solution to get a mobile solution.
Thanks and best regards,
Carsten

Spectrum Expert can't detect Wireless network and show SNR info

Hello,
We are using the version 3.2.163 of the Spectrum Expert on a shared laptop. I was able to see SSIDs under Active Devices and get display in SNR chart before. But recently for some reason, I can can't get SSIDs and only get interfering devices listed under Active Devices and got nothing deplayed in the SNR chart. I could not trace back what has been changed and double checked most of the settings, still not luck.
I appreciate any suggestions to get this fixed.
Thank you!

Humm, no comments from the experts?
Ok, I will give it a try.
I have SE 3.3.53 connected to a version 1 sensor card, loaded in a Compaq nw8440 laptop with an Intel 3945ABG nic.
Win7.
Spectrum Expert Sensor card provides the Analog RF energy data. Only.
The 3945 provides the digital network information via the windows API (WZC in XP) (WLAN AutoConfig in Win7).
Various windows patches and updates have interfeered with the ability of third-party applications to intercept or latch-on-to the data from the wnic.
SE no longer hears my 3945. However, I plugin a Cisco/Linksys AE2500 usb unit and presto Active Device data appears.
Interesting feature is that when I remove the USB wnic, the data link established attaches to the onboard wnic data stream.
On my XP desktop I use SE 4.1.11 for SE Remote.
The digital link is also broken, with everything I try. But then you don't want/need Active Device data from your house when your remoting to a distant shop.
I don't understand why the 3502/3602's can pass digital info right along with the analog data.
So in your case maybe installing another wnic might help with your issue.
David

Where to download ESR for SAP NetWeaver CE 7.1, SR5 TRAIL VERSION?

Hi Netweaver CE experts,
Can please someone tell me where do download Enterprise Service Repository (ESR) for SAP NetWeaver CE 7.1, SR5 ?
There is no such link in SDN and I need the TRAIL version , not the licensed one.
SAP used to have it with SR3 but I cannot find it for CE 7.1 SR5?
Appreciate you help!
Jim

hi
find below link
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/webcontent/uuid/307e90ef-0a65-2a10-e48e-c5a888c81537
Regards
Murali Papana.

Where to download ESR for SAP NetWeaver CE 7.1, SR5 ?

Hi Netweaver experts,
Can please someone tell me where do download Enterprise Service Repository (ESR) for SAP NetWeaver CE 7.1, SR5 ?
There is no such link in SDN and I need the TRAIL version , not the licensed one.
SAP used to have it with SR3 but I cannot find it for CE 7.1 SR5?
Appreciate you help!
Jim

Hi Vinit,
Thanks for your reply .
I got it , There are 3 files ESR for SAP Netweaver CE 7.1 SP5 1 of 3 - 900M(,exe), ESR for SAP Netweaver CE 7.1 SP5 2 of 3 - 900M(rar) and ESR for SAP Netweaver CE 7.1 SP5 1 of 3 - 900M(rar) .Should I donwload all of them???
And Also they are not TRAIL versions. so they will expire for 30 days...I need the TRAIL version...SAP used to have it in SDN...?Do you know where I can find the TRAIL version
Thanks!
Jim

Where to download B2B Adapter?

where to download B2B Adapter that allow BPEL to integrate with Oracle B2B Integration??

thanks, i manage to get the B2B adapter but i face another problem when i try to deploy.
here is the error i got from the log.
ORABPEL-05207
Error deploying BPEL archive.
An error occurred while attempting to deploy the BPEL archive file "bpel_Enqueue850_1.1.jar"; the exception reported is: Problem 1: [http://localhost:9700/BPELConsole/wsil/adapters/B2B/EDI_X12/X12_4010-4010/850/850+Definition?wsdl]: Unable to locate the JCA Resource Adapter via WSDL port element jca:address.
The Adapter Framework is unable to startup the Resource Adapter specified in the WSDL jca:address element: {http://xmlns.oracle.com/pcbpel/wsdl/jca/}address: location='eis/b2b'
The reason for this is most likely that either
1) the Resource Adapters RAR file has not been deployed successfully to the OC4J Application server or
2) the 'location' attribute in $J2EE_HOME/application-deployments/default/deployed-adapter-name/oc4j-ra.xml has not been set to eis/b2b. In the last case you might have to add a new 'connector-factory' entry (connection) to oc4j-ra.xml.
Please correct this and then restart the BPEL/OC4J Application Server
any idea how to fix this problem?

Where to download Cisco Spectrum Expert Connect (4.0 or greater)?

Similar Messages

Maybe you are looking for