Where to find package language for ISM-SRE-300-k9 CUE 8.6.1
Hi,
I need to add a new language package in ISM-SRE-300-K9. Currently it has CUE Voicemail European Spanish (Spanish language pack) (8.6.1) but I need
Spanish Mexican.
I have read the procedure to add additional package but I can't find the package cue-vm-langpack.ise.8.6.1. pkg , I have just found
the file cue-vm-es_MX-langpack.ise.8.6.1.prt1.
any of you know where I can find the package I need?
regards
Paolo,
I have tried to install the package in ISM-SRE-300-K9 but I received an error mesage.
I have already load all the file in ftp server folder , I have tried with anonymous user and not anonymous but fail
do you know the reason of this error??
CUE# software install add cue-vm-langpack.ise.8.6.1.pkg
WARNING:: This command will install the necessary software to
WARNING:: complete an add-on install. It is recommended that a backup be done
WARNING:: before installing software.
Would you like to continue?[confirm]
Downloading ftp cue-vm-langpack.ise.8.6.1.pkg
Bytes downloaded : 1385425
Validating package signature ...
ERROR get_pkg_list:Package signature validation failed for cue-vm-langpack.ise.8.6.1.pkg
Package signature validation failed for cue-vm-langpack.ise.8.6.1.pkg
CUE#
Similar Messages
-
X7: where to find German language for Swype?
I know that I can install Swype onto my X7 via Ovi store. But how can I get German language support for Swype installed? I managed to install it on my C7 a few months ago, but now it seems to have disappeared from the Nokia Beta Labs site......or did I just not look in the right places?
farby wrote:
..or just check the last post by FuRCoM
http://forum.dailymobile.se/index.php?topic=29147.150
German language was never officially supported - but you could get it thru Beta Labs and it worked fine (on my C7). Now it was removed from Beta Labs - why?
The link that you sent points to an older version - I already tried this out but when changing language to German it says "...update from Ovi store needed...." - and then there is no update on Ovi store.
Like in many other cases - I do not at all understand Nokia's strategy here. For me, Swype is the only way to survive a touchscreen - without support for my native language, the X7 will go back to the dealer. Other manufacturers include Swype BY DEFAULT ! -
Cisco 2901-CME-SRST and ISM-SRE-300-K9 No Package already installed?
Good Morning Everybody,
I'm installing a new CME router with CUE.
But, the ISM-SRE-300-K9 is empty, I don't if it's normal.
I try to install two different packages :
Version 8.5.1
cue-installer.sme.8.5.1
cue-vm-full-k9.sme.8.5.1.prt1
cue-vm-installer-k9.sme.8.5.1.prt1
cue-vm-k9.sme.8.5.1.key
cue-vm-k9.sme.8.5.1.pkg
cue-vm-k9.sme.8.5.1.pkg.install.sre
cue-vm-k9.sme.8.5.1.pkg.install.sre.header
cue-vm-langpack.sme.8.5.1.pkg
Version 8.6.1
cue-installer.SPA.sme.8.6.1
cue-vm-full-k9.SPA.sme.8.6.1.prt1
cue-vm-installer-k9.SPA.sme.8.6.1.prt1
cue-vm-k9.SPA.sme.8.6.1.key
cue-vm-k9.SPA.sme.8.6.1.pkg
cue-vm-k9.SPA.sme.8.6.1.pkg.install.sre
cue-vm-k9.SPA.sme.8.6.1.pkg.install.sre.header
cue-vm-langpack.sme.8.6.1.pkg
Without success...
I try with two differents FTP server (Linux and Windows), connection and session seems ok with Wireshark, but, module go to loop, without installation success.
Different try :
Version 8.5.1
==========
Router#$0 status
Service Module is Cisco ISM0/0
Service Module supports session via TTY line 67
Service Module is trying to recover from error
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
Module resource information:
CPU Frequency: 1068 MHz
Memory Size: 493 MB
Disk 0 Size: 4110 MB
Install of ftp://*****:*****@10.10.80.68/Downloads/cue-vm-k9.sme.8.5.1.pkg in progress
Install status : Waiting for file request
Local Partition Info - (0 apps)
=====================
Retrieving partition information
Router#
Feb 16 06:04:22.583: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:29:03.839: %SYS-5-CONFIG_I: Configured from console by vty0 (10.10.80.68)
Feb 16 06:29:19.915: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:30:01.283: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:30:21.711: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:30:42.143: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:31:02.571: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:31:22.995: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 06:31:22.999: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:31:43.419: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:32:03.843: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:32:45.275: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:33:05.699: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:33:26.119: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:33:46.543: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:34:06.979: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 06:34:06.983: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:34:27.399: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:34:47.831: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:35:29.263: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:35:49.687: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:36:10.119: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:36:30.563: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:36:50.983: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 06:36:50.987: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:37:11.467: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:37:31.887: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:38:13.399: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:38:33.815: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:38:54.243: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File RequestConnection closed by foreign host.
Version 8.6.1
==========
Router#[email protected]/Downloads/cue-vm-k9.SPA.sme.8.6.1.pkg
Proceed with installation? [no]: yes
Feb 16 07:16:21.235: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Loading Downloads/cue-vm-k9.SPA.sme.8.6.1.pkg.install.sre !
[OK - 38648/4096 bytes]
No local store partition
Following languages are available for installation.
# SKU Language Code Language Name
1 ARA ar_SA CUE Voicemail Arabic
2 DAN da_DK CUE Voicemail Danish
3 DEU de_DE CUE Voicemail German
4 ENG en_GB CUE Voicemail UK English
5 ENU en_US CUE Voicemail US English
6 ESO es_CO CUE Voicemail Latin American Spanish
7 ESP es_ES CUE Voicemail European Spanish
8 ESM es_MX CUE Voicemail Mexican Spanish
9 FRC fr_CA CUE Voicemail Canadian French
10 FRA fr_FR CUE Voicemail European French
11 HUN hu_HU CUE Voicemail Hungarian
12 ITA it_IT CUE Voicemail Italian
13 HBR iw_IL CUE Voicemail Hebrew
14 JPN ja_JP CUE Voicemail Japanese
15 KOR ko_KR CUE Voicemail Korean
16 NLD nl_NL CUE Voicemail Dutch
17 NOR no_NO CUE Voicemail Norwegian
18 PTB pt_BR CUE Voicemail Brazilian Portuguese
19 PTG pt_PT CUE Voicemail Portuguese
20 RUS ru_RU CUE Voicemail Russian
21 SVE sv_SE CUE Voicemail Swedish
22 TUR tr_TR CUE Voicemail Turkish
23 CHS zh_CN CUE Voicemail Simplified Chinese (PRC)
24 ZHH zh_HK CUE Voicemail Hong Kong Chinese
25 CHT zh_TW CUE Voicemail Traditional Chinese (Taiwan)
You can install upto 5 language(s) on this platform.
Please select the language(s) you want to install by entering the language number(s)
Languages can be entered as comma separated or space separated list
Example: 1,3 would select 'CUE Voicemail Arabic' and 'CUE Voicemail German'
Enter languages:4
Following languages will be installed on the system:
CUE Voicemail UK English
Do you want to continue with the selected options?(y/n):y
Router#
Feb 16 07:16:50.579: %SM_INSTALL-6-INST_RESET: ISM0/0 is reset for software installation.
Feb 16 07:17:11.235: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 07:17:11.239: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
===========================
on the service-module ism0/0 session
===========================
Initializing memory. Please wait...
Memory initialization OK. Continue...
Feb 16 07:25:08.683: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Primary Boot Loader Authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
SRE step 2 - SM requests key file info...
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:25:29.259: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 07:25:29.263: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Time-out from RBIP response wait loop
SRE step 3 - SM stores registration info...
Updating flash with bootloader configuration.
Please wait .............. done.
SRE step 4 - SM downloads key-file...
!!! Opcode Error - Get a wrong RBIP frame !!!
Writing keyfile to flash Size 891
writing complete.
SRE step 5 - SM requests installer info...
Feb 16 07:25:49.791: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
SRE step 6 - SM stores installer info...
Updating flash with bootloader configuration.
Please wait .............. done.
SRE step 7 - SM now downloads installer
|
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:26:10.343: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Requestdone.
SRE step 8 - SM requests tcl header file info...
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:26:52.919: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Time-out from RBIP response wait loop
SRE step 9 - SM now downloads the tcl header file
|
!!! Opcode Error - Get a wrong RBIP frame !!!
TCL header file downloaded completely size: 691
SRE step 10 - SM requests tcl file info...
Feb 16 07:27:13.467: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Time-out from RBIP response wait loop
SRE step 11 - SM now downloads the tcl file
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:27:34.011: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File RequestTCL file downloaded completely size: 691
SRE step 12 - SM now boots Installer
Verifying ...
Corrupted netboot image detected
done.
Starting Kernel.
loop ....
I have no idea to solve my problem...
If anybody have suggestion, should be great.
Have a nice day !
Thanks
FabHi,
I try that. From this guide :
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel3_0/installation/guide/upg3boot.pdf
with windows xp tftpd32
computer config : 192.168.1.4/24
ftp server 192.168.1.3 /24
Router int g0/0 192.168.1.1 255.255.255.0 + ip route 192.168.1.2 255.255.255.255 ism 0/0
ISM :
ServicesEngine boot-loader> show config
IP addr: 192.168.1.2
Netmask: 255.255.255.0
TFTP server : 192.168.1.4
GW IP addr: 192.168.1.1
Default Boot: disk
Bootloader Version: 2.1.18
Bootloader Name: bootloader
Default Helper-file: cue-installer.sme.8.5.1
Default bootloader: primary
From Computer :
C:\Documents and Settings\f>ping 192.168.1.2 -t
Pinging 192.168.1.2 with 32 bytes of data:
Reply from 192.168.1.2: bytes=32 time<1ms TTL=126
Icmp from ism to computer: no response.
from ism to router int g0/0 : no response too.
router to ism (boot-loader): ok
pc to ism (boot-loader) : ok
So when I try "boot helper" , the request tftp didn't come to my computer.
ServicesEngine boot-loader> boot helper
Loading tftp://192.168.1.4/cue-installer.sme.8.5.1 ...
ServicesEngine boot-loader>
Thank you for your help. -
Where to find a driver for a seagate product or the operating system (OS) fails to recognize a seagate drive
Name : Seagate Backup+ BL Media
Type : Disk
Partition Map Scheme : Master Boot Record
Disk Identifier : disk1
Media Name : Seagate Backup+ BL Media
Media Type : Generic
Connection Bus : USB
USB Serial Number : NA5B83S2
Device Tree : IODeviceTree:/PCI0@0/XHC1@14
Writable : Yes
Ejectable : Yes
Location : External
Total Capacity : 1 TB (10,00,20,48,85,504 Bytes)
Disk Number : 1
Partition Number : 0
S.M.A.R.T. Status : Not SupportedSeagate website.
Why don't you reformat the drive in Disk Utility or Terminal. Screw that rubbish backup software on the seagate drive. -
PA-US Where to find the documentation for renumeration type?
Gurus,
Where to find the documentation for renumeration type details for IT0008 in SAP Library?
I tried in HR sections under ERP of SAP Library, but could not find the place.
Thanks,Revathi,
I see an option to change the enum type in IT0008 maintenance screen.
Which simply changes section of the screen as "salary" to "pay scale" and vice versa.
I want to understand the difference between those in terms of payroll process (calculations).
Hence, I was trying to find documentation in this regard in SAP Library.
Thanks, -
Does anyone know where to find printer profiles for Epson paper with MG6200 printer for use in LightRoom5?
Epsnm should provide recommended settings (I.e. Which Canon paper type to select). They may also have profiles on their site.
John Hoffman
Conway, NH
1D Mark IV, Rebel T5i, Pixma PRO-100, MX472 -
Where i find the drivers for hp j5783 scaner
where i find the drivers for hp j5783 scaner
Hello ezraie, and welcome to the HP Forums, I hope you enjoy your experience!
I see you are looking for the drivers. I would like to help.
I would recommend following this link to the HP Officejet J5783 All-in-One Printer Drivers.
Please let me know if you have any questions. Thanks for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green. -
Verizon, where are my additional languages for swype?
Verizon, where are my additional languages for swype?
Why I'm limited to only English and Spanish?!
How to add more languages to my phone?Thanks for the information crb79. After review of the skype application, I was able to locate two applications. We offer a Skype mobile and a Skype Mobile for VErizon. If you downloaded the Skype mobile for Verizon, you may be limited to only two languages. Skype mobile offers all languages. I recommend checking your application and if you have the skype version that only offers two languages, you can remove it and download the Skype Mobile version. I will list directions below.
You can also research information via the internet for Skype Translate Tool/software. While we do not support this tool and always recommend contacting Skype first, you can review further information via the internet.
To remove an application:
From the home screen, select the applications tab (located at the bottom of the display).
Select Settings.
Select Applications.
Select Manage applications.
From the All tab, select an application.
Select Uninstall.
Select OK.
Select OK.
To install applications from the Android Market:
From the home screen, touch the applications tab (located at the bottom of the display).
Touch Market.
If presented, review the Android Market Terms of Service then touch Accept to continue.
Touch Apps.
Touch a category (e.g. All applications, Comics, Communication, etc.).
To sort the list, touch one of the following:
Top paid
Top free
Just in
Touch an application / widgetsuch as:
Widgets
CNN News
Delivers up-to-the-minute news and information on the latest top stories, weather, and entertainment.
Weather Bug
Delivers live local weather conditions.
Fox News
Delivers the latest and breaking news.
Applications
Visual Voice Mail
Allows subscribers to view caller and voice mail information and listen to voice mail messages in any order.
If there is a charge for the application, touch Buy.
If the application is free, touch Install.
Touch OK.
Review the alerts for access. If they are not acceptable touch Cancel.
If applicable, ensure the desired card is selected then touch Buy now.
If a payment method has not been established, enter the credit card information then touch Save -
ISM-SRE-300 seems to be a loop at boot with Verifying ... Invalid signature in command line file
Any ideas?
Log
Install of ftp://*****:*****@10.100.64.21/cue-vm-k9.SPA.sme.8.6.7.pkg in progress
Install status : Waiting for RBIP registration
No localstore
2911#
[Resuming connection 1 to 10.102.66.254 ... ]
Initializing memory. Please wait...
Memory initialization OK. Continue...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
SRE step 2 - SM requests key file info...
SRE step 3 - SM stores registration info...
SRE configuration keeps the same. No flash update needed!
SRE step 4 - SM downloads key-file...
Writing keyfile to flash Size 891
writing complete.
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 5 - SM requests installer info...
SRE step 6 - SM stores installer info...
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 7 - SM now downloads installer
done.
SRE step 8 - SM requests tcl header file info...
SRE step 9 - SM now downloads the tcl header file
TCL header file downloaded completely size: 691
SRE step 10 - SM requests tcl file info...
SRE step 11 - SM now downloads the tcl file
TCL file downloaded completely size: 38933
SRE step 12 - SM now boots Installer
Verifying ... done.
Starting Kernel.
Platform: ism
INIT: version 2.86 booting
mounting proc fs ...
mounting sys fs ...
mounting /dev/shm tmpfs ...
kernel.sem = 1900 4000 32 100
vm.overcommit_memory = 1
vm.min_free_kbytes = 8192
Welcome to Cisco Service Engine
Setting the system time from hardware clock
********** rc.aesop ****************
Populating resource values from /etc/ism_rsrc_file
Populating resource values from /etc/default_rsrc_file
Populating resource values from /etc/products/cue/default_rsrc_file
Populating resource values from /etc/products/cue/ism_rsrc_file
==> Management interface is eth0
==> Management interface is eth0
IOS IP Address Registration complete.
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.102.66.0 * 255.255.255.0 U 0 0 0 eth0
default 142.102.66.254 0.0.0.0 UG 0 0 0 eth0
Size of buff is: 65536
65536 bytes written
Valid License file not found: Using default values
INIT: Entering runlevel: 2
********** rc.post_install ****************
Changing owners and file permissions.
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
STARTED: dwnldr_startup.sh
sre_type= 1
Welcome to Cisco Systems Service Engine Helper Software
Downloading ftp cue-vm-k9.SPA.sme.8.6.7.pkg
Bytes downloaded : 727736
Validating package signature ... done
- Parsing package manifest files... complete.
No installed manifests found.
- Checking Package dependencies... complete.
Downloading ftp cue-vm-langpack.sme.8.6.7.pkg
Error: Download error
Can not download cue-vm-langpack.sme.8.6.7.pkg
error code 550 : error type 'Can not ▒
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...ISM-SRE-300 seems to be a loop at boot with Verifying ... Invalid signature in command line file
Any ideas?
Log
Install of ftp://*****:*****@10.100.64.21/cue-vm-k9.SPA.sme.8.6.7.pkg in progress
Install status : Waiting for RBIP registration
No localstore
2911#
[Resuming connection 1 to 10.102.66.254 ... ]
Initializing memory. Please wait...
Memory initialization OK. Continue...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
SRE step 2 - SM requests key file info...
SRE step 3 - SM stores registration info...
SRE configuration keeps the same. No flash update needed!
SRE step 4 - SM downloads key-file...
Writing keyfile to flash Size 891
writing complete.
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 5 - SM requests installer info...
SRE step 6 - SM stores installer info...
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 7 - SM now downloads installer
done.
SRE step 8 - SM requests tcl header file info...
SRE step 9 - SM now downloads the tcl header file
TCL header file downloaded completely size: 691
SRE step 10 - SM requests tcl file info...
SRE step 11 - SM now downloads the tcl file
TCL file downloaded completely size: 38933
SRE step 12 - SM now boots Installer
Verifying ... done.
Starting Kernel.
Platform: ism
INIT: version 2.86 booting
mounting proc fs ...
mounting sys fs ...
mounting /dev/shm tmpfs ...
kernel.sem = 1900 4000 32 100
vm.overcommit_memory = 1
vm.min_free_kbytes = 8192
Welcome to Cisco Service Engine
Setting the system time from hardware clock
********** rc.aesop ****************
Populating resource values from /etc/ism_rsrc_file
Populating resource values from /etc/default_rsrc_file
Populating resource values from /etc/products/cue/default_rsrc_file
Populating resource values from /etc/products/cue/ism_rsrc_file
==> Management interface is eth0
==> Management interface is eth0
IOS IP Address Registration complete.
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.102.66.0 * 255.255.255.0 U 0 0 0 eth0
default 142.102.66.254 0.0.0.0 UG 0 0 0 eth0
Size of buff is: 65536
65536 bytes written
Valid License file not found: Using default values
INIT: Entering runlevel: 2
********** rc.post_install ****************
Changing owners and file permissions.
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
STARTED: dwnldr_startup.sh
sre_type= 1
Welcome to Cisco Systems Service Engine Helper Software
Downloading ftp cue-vm-k9.SPA.sme.8.6.7.pkg
Bytes downloaded : 727736
Validating package signature ... done
- Parsing package manifest files... complete.
No installed manifests found.
- Checking Package dependencies... complete.
Downloading ftp cue-vm-langpack.sme.8.6.7.pkg
Error: Download error
Can not download cue-vm-langpack.sme.8.6.7.pkg
error code 550 : error type 'Can not ▒
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting... -
Installing CUE 8.6.7 on ISM-SRE-300-K9
Hello,
I been trying to install CUE on ISM0/0 but so far i havent been available...
My configuration goes as follow:
interface ISM0/0
ip unnumbered GigabitEthernet0/0.11
ip virtual-reassembly in
service-module fail-open
service-module ip address 130.11.1.3 255.255.0.0
service-module ip default-gateway 130.11.1.1
end
ip route 130.11.1.3 255.255.255.255 ISM0/0
till this point everything goes ok, i have connectivity between each of em...
then on ISM my config is
ServicesEngine boot-loader> show config
IP addr: 130.11.1.3
Netmask: 255.255.0.0
TFTP server : 130.11.1.1
GW IP addr: 130.11.1.1
Default Boot: disk
Bootloader Version: 2.1.18
Bootloader Name: bootloader
Default Helper-file: /cue-installer.SPA.sme.8.6.7
Default bootloader: secondary
however when i issue the boot helper command it goes on a cycle showing the next output
Loading tftp://130.11.1.1/cue-installer.SPA.sme.8.6.7 ... done.
Verifying ...
Corrupted netboot image detected
done.
Starting Kernel.
After this server reboot and it goes on cycling.
I have checked this guide so far, and i think im not missing a step.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel8_6/install/CUE_86_install/boothelp.html
TYVMSure can, here are my outputs
-------Show Ver--------
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.3(2)T, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 28-Mar-13 11:05 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
RTR_V_CPACK uptime is 15 hours, 30 minutes
System returned to ROM by reload at 19:31:49 CUU Mon Apr 14 2014
System image file is "flash0:c2900-universalk9-mz.SPA.153-2.T.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2921/K9 (revision 1.0) with 1523712K/49152K bytes of memory.
Processor board ID FTX1749AJ5G
4 Gigabit Ethernet interfaces
2 terminal lines
1 Channelized E1/PRI port
6 Voice FXO interfaces
1 Internal Services Module (ISM) with Services Ready Engine (SRE)
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2921/K9 FTX1749AJ5G
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security None None None
uc uck9 Permanent uck9
data None None None
Configuration register is 0x2102
------------Show diag--------------------
Slot 0:
C2921 Mother board 3GE, integrated VPN and 4W Port adapter, 10 ports
Port adapter is analyzed
Port adapter insertion time 15:30:43 ago
EEPROM contents at hardware discovery:
PCB Serial Number : FOC17420KBG
Hardware Revision : 1.0
Part Number : 73-11835-11
Top Assy. Part Number : 800-30794-07
Board Revision : A0
Deviation Number : 130603
Fab Version : 03
Product (FRU) Number : CISCO2921/K9
Version Identifier : V08
CLEI Code : CMMHS10ARB
Processor type : C2
Chassis Serial Number : FTX1749AJ5G
Chassis MAC Address : 78da.6e82.b600
MAC Address block size : 80
Manufacturing Test Data : 00 00 00 00 00 00 00 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 37 34 32 30 4B 42 47 40
0x10: 06 16 41 01 00 82 49 2E 3B 0B C0 46 03 20 00 78
0x20: 4A 07 42 41 30 88 00 01 FE 2B 02 03 CB 8C 43 49
0x30: 53 43 4F 32 39 32 31 2F 4B 39 89 56 30 38 20 D9
0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 48 53 31 30 41 52
0x50: 42 09 C2 C2 8B 46 54 58 31 37 34 39 41 4A 35 47
0x60: C3 06 78 DA 6E 82 B6 00 43 00 50 C4 08 00 00 00
0x70: 00 00 00 00 00 F3 00 03 40 01 63 FF FF FF FF FF
0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Internal Power Supply information
Top Assy. Part Number : 341-0226-03
Deviation Number : 0
PCB Serial Number : DCA1738K05Q
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier : V03
Product (FRU) Number : PWR-2921-51-AC
CLEI Code : 0000000000
Board Revision : A0
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 E2 DF 45 01 55 00 E2 03 88 00 00 00
0x10: 00 C1 8B 44 43 41 31 37 33 38 4B 30 35 51 03 00
0x20: 81 00 00 00 00 04 00 89 56 30 33 20 CB 8E 50 57
0x30: 52 2D 32 39 32 31 2D 35 31 2D 41 43 C6 8A 30 30
0x40: 30 30 30 30 30 30 30 30 F3 00 59 41 01 22 42 00
0x50: 05 F8 00 50 01 F3 18 3B 02 F0 19 D9 03 E8 1B 76
0x60: 04 E2 1C 49 05 D9 1D 1B 06 D8 1D ED 07 CF 1E BF
0x70: 08 CE 1F 40 09 C2 1F B8 0A B8 20 34 0B B7 20 B0
0x80: 0D AF 21 0C 0F 9F 21 67 11 91 21 94 13 87 21 C0
0x90: 17 6E 21 DB 1B 57 21 EA 1F 3F 21 E2 23 28 21 D4
0xA0: 27 0A 21 CD 42 41 30 FF FF FF FF FF FF FF FF FF
0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
PVDM Slot 0:
64-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card
Hardware Revision : 1.0
Part Number : 73-11809-03
Board Revision : D0
Deviation Number : 0
Fab Version : 03
PCB Serial Number : FOC17453K9V
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM3-64
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 DB 41 01 00 82 49 2E 21 03 42 44 30
0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 37 34 35
0x20: 33 4B 39 56 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 8F 50 56 44 4D 33 2D 36 34 20 20 20 20 20 20 20
0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1
Hardware Revision : 1.0
Top Assy. Part Number : 800-34657-01
Part Number : 73-13419-01
Board Revision : B0
Deviation Number : 0
Fab Version : 05
PCB Serial Number : FOC1745429E
Version Identifier : V01
Product (FRU) Number : VWIC3-1MFT-T1/E1
CLEI Code : COUIA7PCAA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 06 ED 41 01 00 C0 46 03 20 00 87 61 01
0x10: 82 49 34 6B 01 42 42 30 88 00 00 00 00 02 05 C1
0x20: 8B 46 4F 43 31 37 34 35 34 32 39 45 89 56 30 31
0x30: 20 CB 90 56 57 49 43 33 2D 31 4D 46 54 2D 54 31
0x40: 2F 45 31 C6 8A 43 4F 55 49 41 37 50 43 41 41 03
0x50: 00 81 00 00 00 00 04 00 D9 03 40 C1 CB FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 1:
2nd generation - FXO Voice daughter card (4 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-33585-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC174279XY
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VIC2-4FXO
Version Identifier : V04
CLEI Code : CNUIAXJAAC
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 83 31 01
0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 37 34 32 37 39 58 59 03 00 81 00 00 00 00 04 00
0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 34 20
0x40: C6 8A 43 4E 55 49 41 58 4A 41 41 43 FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 2:
2nd generation - FXO Voice daughter card (2 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-33584-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC1745AP4H
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VIC2-2FXO
Version Identifier : V03
CLEI Code : CNUIARTAAC
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 4D 41 05 00 C0 46 03 20 00 83 30 01
0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 37 34 35 41 50 34 48 03 00 81 00 00 00 00 04 00
0x30: CB 89 56 49 43 32 2D 32 46 58 4F 89 56 30 33 20
0x40: C6 8A 43 4E 55 49 41 52 54 41 41 43 FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Internal Services Module (ISM) Slot 0
Internal Services Module with Services Ready Engine
Internal Services Module is analyzed
Internal Services Module insertion time 15:30:43 ago
EEPROM contents at hardware discovery:
PCB Serial Number : FOC174782WY
Hardware Revision : 1.0
Part Number : 73-13417-01
Top Assy. Part Number : 800-34577-01
Deviation Number : 0
Fab Version : 04
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
CLEI Code : IPUCAXHBAB
Product (FRU) Number : ISM-SRE-300-K9
Version Identifier : V02
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 37 34 37 38 32 57 59 40
0x10: 06 31 41 01 00 82 49 34 69 01 C0 46 03 20 00 87
0x20: 11 01 88 00 00 00 00 02 04 42 41 30 03 00 81 00
0x30: 00 00 00 04 00 C6 8A 49 50 55 43 41 58 48 42 41
0x40: 42 CB 8E 49 53 4D 2D 53 52 45 2D 33 30 30 2D 4B
0x50: 39 89 56 30 32 20 D9 03 40 C1 CB F3 00 06 40 05
0x60: F3 43 00 16 FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Embedded Service Engine 0/0 :
Total platform memory : 1572864K bytes
Total 2nd core memory : 0K bytes
Start of physical address for 2nd core : 0x80000000
Virtual address start of 2nd core memory : 0x0 - 0x0
2nd core configured disabled
L2 cache ways for 2nd core : 0
-------------------------Show Inv-------------------------------------
RTR_V_CPACK#sh inv
NAME: "CISCO2921/K9", DESCR: "CISCO2921/K9 chassis, Hw Serial#: FTX1749AJ5G, Hw Revision: 1.0"
PID: CISCO2921/K9 , VID: V08 , SN: FTX1749AJ5G
NAME: "VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC3-1MFT-T1/E1 , VID: V01 , SN: FOC1745429E
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V04 , SN: FOC174279XY
NAME: "2nd generation two port FXO voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation two port FXO voice interface daughtercard"
PID: VIC2-2FXO , VID: V03 , SN: FOC1745AP4H
NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 64 Channels"
PID: PVDM3-64 , VID: V01 , SN: FOC17453K9V
NAME: "Internal Services Module with Services Ready Engine on Slot 0", DESCR: "Internal Services Module with Services Ready Engine"
PID: ISM-SRE-300-K9 , VID: V02 , SN: FOC174782WY
NAME: "C2921/C2951 AC Power Supply", DESCR: "C2921/C2951 AC Power Supply"
PID: PWR-2921-51-AC , VID: V03 , SN: DCA1738K05Q
TYVM -
Hi ,
Can anybody help me to solve the following error , while installing new ISM-SRE-300-K9 unity express module .
Available commands are:
# - enter the number for the language to select one
r # - remove the language for given #
i # - more information about the language for given #
x - Done with language selection
Enter Command:3
Language Installation Menu:
# Selected SKU Language Name (version)
1 ITA CUE Voicemail Italian (8.6.1)
2 ESP CUE Voicemail European Spanish (8.6.1)
3 * ENU CUE Voicemail US English (8.6.1)
4 FRA CUE Voicemail European French (8.6.1)
5 ESO CUE Voicemail Latin American Spanish (8.6.1)
6 ESM CUE Voicemail Mexican Spanish (8.6.1)
7 ARA CUE Voicemail Arabic (8.6.1)
8 NLD CUE Voicemail Dutch (8.6.1)
9 SVE CUE Voicemail Swedish (8.6.1)
10 NOR CUE Voicemail Norwegian (8.6.1)
11 FRC CUE Voicemail Canadian French (8.6.1)
12 PTG CUE Voicemail Portuguese (8.6.1)
13 TUR CUE Voicemail Turkish (8.6.1)
14 HUN CUE Voicemail Hungarian (8.6.1)
15 ENG CUE Voicemail UK English (8.6.1)
16 DEU CUE Voicemail German (8.6.1)
17 HBR CUE Voicemail Hebrew (8.6.1)
18 DAN CUE Voicemail Danish (8.6.1)
19 PTB CUE Voicemail Brazilian Portuguese (8.6.1)
20 CHT CUE Voicemail Traditional Chinese (Taiwan) (8.6.1)
21 KOR CUE Voicemail Korean (8.6.1)
22 CHS CUE Voicemail Simplified Chinese (PRC) (8.6.1)
23 JPN CUE Voicemail Japanese (8.6.1)
24 ZHH CUE Voicemail Hong Kong Chinese (8.6.1)
25 RUS CUE Voicemail Russian (8.6.1)
Available commands are:
# - enter the number for the language to select one
r # - remove the language for given #
i # - more information about the language for given #
x - Done with language selection
Enter Command:x
ui_install scripts executed successfully.
Starting payload download
File transfer error during download. Curl error code is 78
Error: Error encountered while downloading payload(s)
Error encountered while downloading payload(s)
Unable to install. Please try again
Please select from the following
1 Install software
2 Reload module
3 Disk cleanup
4 Install License(s)
(Type '?' at any time for help)
Choice:Hi,
This error indicates that you are missing a language installation file, please download it from the same directory (version of CUE) and try the installation.
HTH
Manish -
Hello
Im installing a CUCME + CUE, after the instalation of the ISM-SRE-300-K9 in 2921
i configure the module but in show commands it appears as failed, and i cannot access the service module.
IOS : c2900-universalk9-mz.SPA.151-4.M2
CUCME: 8.6
CUE Module: ISM-SRE-300-K9
This message appears on the console:
%SRE_SM-6-STATE_CHANGE: ISM0/0 changing state from SERVICE_MODULE_STATE_SHDN to SERVICE_MODULE_STATE_FAIL
CUE Config on CUCME
interface ISM0/0
ip unnumbered G0/0
service-module ip address 176.16.1.7 255.255.255.0
service-module ip default-gateway 176.16.1.1
no keepalive
ip route 176.16.1.7 255.255.255.255 ISM0/0
dial-peer voice 8100 voip
mailbox-selection orig-called-num
description ------------------------------[CUE]
destination-pattern 80..
session protocol sipv2
session target ipv4:176.16.1.7
dtmf-relay sip-notify
codec g711ulaw
no vad
telephony-service
voicemail 8000
Logs:
%SRE_SM-6-STATE_CHANGE: ISM0/0 changing state from SERVICE_MODULE_STATE_SHDN to SERVICE_MODULE_STATE_FAIL
GW01#service-module iSM 0/0 status
Service Module is Cisco ISM0/0
Service Module supports session via TTY line 131
Service Module is failed
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
No install/uninstall in progress
Local Partition Info
=====================
Please reset module to retrieve
partition information if needed
Somebody can help me?
ThanksDid u eventually got this running, I too have the same problem.
I am unable to configure the SRE-300-K9, always i have to reset and go to the int ism0/0 and give no shut to bring it up but it comes up in boot loader configuration.
I tried to install using the guide but after all installation and language selection it keeps saying as payload missing and curl code error 19 and sometimes curl code error 78.
If u already found some solutions pls share it. -
ISM-SRE-300 don´t allow send data between clients and pc in LAN
I have an ISM-SRE-300 on cisco 1941 does not allow sending of data between clients attached to an AP wired to PC Networking.
LAN CLIENT= VLAN 20 10.94.4.0 /24
SERVER CLIENTE = 10.94.4.1 D.G= 10.94.4.254
ROUTER
INT G0/0.1= IP UNNUMBERED VLAN 1 NATIVE VLAN
INT G 0/0.20 = IP UNNUMBERED VLAN 20
INT VLAN 1 = 94.4.1.1 /24
INT VLAN 20 = 10.94.4.254 /24
ISM-SRE
MANAGEMENT UNTAGGED 94.4.1.2
VLAN 20 VLAN=20 IP=10.94.4.251 /24 D.G. 10.94.4.254
IF SENDING PING FROM ROUTER TO SERVER=10.94.4.1 IS OK
IF SENDING PING FROM ISM TO SERVER DON´T ANSWER
IF JOIN A CLIENT IN AP, CLIENT WIRELESS=10.94.4.150 /24 D.G. 10.94.4.254
I SEND PING TO ISM 10.94.4.251 IS OK
I SENG PING TO ROUTER 10.94.4.254 DON´T ANSWER
I SEND PING FROM SERVER (10.94.4.1) TO ROUTER 10.94.4.254 IS OK
I SEND PING TO ISM 10.94.4.251 DON´T WORK
I SENG PING TO CLIENT WIRELESS 10.94.4.150 DON´T WORK
CAN ANYONE HELP ME ?
THANKS
JUAN-RAMONJust to be clear, this posting is NOT asking for help. This is a posting to help those with the HARDWARE side of the configuration. This is what I just finished doing in my lab for testing. Worked great. DHCP, WLAN Advertising, etc. I now have to go on to the next harder steps of really combing through the WLC configuration, applying our standard template configurations for our Routers/Switches, applying dual and tertiary redundancy with regards to routing, DHCP via MICROSOFT and not using a switch, and so on.
This was just meant to help those who don't have a lot of experience configuring the router switch environment. Sorry if I confused any one. -
ISM-SRE-300 - Lab Configuration
I'm using the ISM-SRE-300 for the Wireless LAN Controller solution. All our sites have a 2911 Router, and a 3750-x (3750x) Catalyst Switch with Routing enabled.
NOTE: This only covers the basic configuration of the networking side. If you set this up in a lab, you can follow other articles to install the Cisco Wireless LAN Controller software via FTP quite easily. Getting the basic infrastructure to work is the hard part.
Sometimes, a little help is all you need.
LAB ROUTER
Note: Some old-schoolers don't like VLAN(1) on the raw interface. They like to change it to a VLAN sub-interface.
interface GigabitEthernet0/1
description *** CONNECTS TO L3 SWITCH
no ip address
duplex auto
speed auto
interface GigabitEthernet0/1.1
encapsulation dot1Q 1 native
ip address 10.1.1.2 255.255.255.0
interface ISM0/0
ip unnumbered GigabitEthernet0/1.1
service-module ip address 10.1.1.10 255.255.255.0 (note: don't try to ping this IP. Won't respond. But it works!)
service-module ip default-gateway 10.1.1.2
interface ISM0/1
description *** MGF Interface (Handles switching for Router; Releives RTR CPU - This is cool. You should read up on this.)
switchport mode trunk
vlan 30
name WIFI_EMPLOYEES
vlan 40
name WIFI_GUESTS
interface Vlan1
ip address 55.1.0.1 255.255.255.0
interface Vlan30
ip address 55.30.0.1 255.255.0.0
ip helper-address 10.1.1.1
interface Vlan40
ip address 55.40.0.1 255.255.0.0
ip helper-address 10.1.1.1
router eigrp 1
network 10.1.1.0 0.0.0.255
network 55.1.0.0 0.0.0.255
network 55.30.0.0 0.0.0.255
network 55.40.0.0 0.0.0.255
ip route 10.1.1.10 255.255.255.255 ISM0/0 (very, very important!!!)
LAB SWITCH
ip routing
ip dhcp excluded-address 10.1.1.1 10.1.1.10
ip dhcp excluded-address 20.1.1.1 20.1.1.10
ip dhcp excluded-address 55.30.0.1 55.30.0.10
ip dhcp excluded-address 55.40.0.1 55.40.0.10
ip dhcp pool management
network 10.1.1.0 255.255.255.0
default-router 10.1.1.2
ip dhcp pool ap-pool
network 20.1.1.0 255.255.255.0
default-router 20.1.1.1
ip dhcp pool WiFi_Employees
network 55.30.0.0 255.255.255.0
default-router 55.30.0.1
ip dhcp pool WiFi_Guests
network 55.40.0.0 255.255.255.0
default-router 55.40.0.1
vlan 20
name AP_VLAN
interface GigabitEthernet1/0/10
description *** CONNECTS TO GIG0/1 on the ROUTER
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/0/11
description *** CONNECTS TO YOUR AP (do not connect it yet until the end when your controller is up and ready to register the AP)
switchport access vlan 20
switchport mode access
interface Vlan1
ip address 10.1.1.1 255.255.255.0
interface Vlan20
description *** VLAN FOR APs (assuming you want all the AP's on their own VLAN)
ip address 20.1.1.1 255.255.255.0
router eigrp 1
network 10.1.1.0 0.0.0.255
network 20.1.1.0 0.0.0.255
ip route 0.0.0.0 0.0.0.0 10.1.1.2
LAPTOP CONFIGURATION
FTP SERVER - Install the FTP software Cisco recommends. I used FILEZILLA. Worked fine on an XP laptop.
WLCM2 IMAGE - Download the WLCM2 ZIP file only. Do not download the AES by itself. Unzip the ZIP file and its contents to the FTP folder. The AES within THE ZIP file is what you refer to, not the AES that you can download separately!!!
FTP
MY PC was connected via CABLE to the 3750-X CATALYST switch that I'm using in the lab. It obtained a DHCP IP of 10.1.1.11.
FTP Command on Router: service-module ism 0/0 install url ftp://[email protected]/AIR-SRE-K9-7.0.112.0.aes
(NOTE: Replace the name with whatever version you downloaded)
WIRELESS LAN CONTROLLER SETUP WIZARD RESPONSES
Term Auto-Install: NO
Admin Name: cisco
Admin PW: cisco
Mgmt Interface: 55.1.0.2
Interface Sub: 255.255.255.0
Gateway: 55.1.0.1
VLAN: 0-Untagged
Interface: 1
DHCP Server: 10.1.1.1
Virtual IP: 1.1.1.1
Multicast: 239.255.1.60
Mobility RF: LAB
SSID: EMPLOYEES (your VLAN 30)
DHCP Bridge: NO
Allow Static: YES
Radius: NO
Country: US
Enable 802.11b: YES
Enable 802.11a: YES
Enable 802.11g: YES
Auto-RF: YES
NTP: NO
Config Correct? YES
What's missing? (Assumption: You've set up controllers before and this stuff comes simple -- let me know otherwise)
- Option 43 in the DHCP Pool configurations. I just entered the CAPWAP command on the AP itself to point it to the Controller.
- Interfaces for EACH VLAN must be configured first before WLAN's
- When you configure the WLAN's, point it to the appropriate VLAN Interface you created.
Tony Ortiz
Network Administrator II
Golden Valley Health Centers (22 sites)Just to be clear, this posting is NOT asking for help. This is a posting to help those with the HARDWARE side of the configuration. This is what I just finished doing in my lab for testing. Worked great. DHCP, WLAN Advertising, etc. I now have to go on to the next harder steps of really combing through the WLC configuration, applying our standard template configurations for our Routers/Switches, applying dual and tertiary redundancy with regards to routing, DHCP via MICROSOFT and not using a switch, and so on.
This was just meant to help those who don't have a lot of experience configuring the router switch environment. Sorry if I confused any one. -
ISM-SRE-300-K9 & Cisco Configuration Professional Issue
hi there,
i have a cisco 2901 router running CME 8.6 the router has a ISM-SRE-300-K9 card init with Unity Express 8.0.5 installed.
i am having issues with Cisco configuration professional and configuring the module
under module configuration the status is "module is not reachable", if i click on details i get further information "unable to execute command from the module. module is either reloading or is in failed state. you must make the module up and refresh the module"
i have tried reloading, resetting and refreshing the module but the issue is still present
i have accessed the module from the CLI set it in offline mode and factory defaulted it and the same issue is still present
the only thing i can think is that this is a bug with CCP as the loopback interface which the module is using can be pinged fine from the router so the message makes no sense.
any ideasIs you problem with CCP or the module itself ?
Because, CCP bugs and limitations aside, the module can be normally be installed, configured and managed using CLI or its web interface (after software is initially loaded).
Maybe you are looking for
-
So the big question here is how on earth do i reset my profiles on Game Center so that I can play my own games. I tried the thing where you swipe and choose remove uninstalled the game no matter what it came back up with the other persons game, inste
-
CS6 Design Standard , clone, migration tool, trial mode (urgence)
Hi all and sorry for this question. I clone on a external disk my MacBook Pro (OSX 10.7) with Super Dumper . Then i have istalled OSX 10.8.2 and imported all data and applications with the migration tool during the installation. My problem is that no
-
After forced shut down iosx does not accept the password on the mcbook air
Hi there, I cannot login into the mcbook air after having to force a shut down. - While surfing with Safari, the mcbook froze for a longer period of time. - We forced the shut down pressing the on/off button. - After rebooting, we have a grayish scre
-
IPad2 not performing with IOS8
-
Hi all, we would like to insert pictures in our documents. The Pictures are stored in a Siebel file system. Does anybody know how we can get them into our documents ? Any help is highly appreciated !!!! Thanks a lot ! Martin