Which E series routers support the Wireless_Advanced.asp hidden page?

I know the E2500 and the E4200 support the http://192.168.1.1/Wireless_Advanced.asp settings but what other E series routers support this hidden page where you can set Beacon Interval, RTS and Fragmentation thresholds?

I own the E3000 v1 and it has this feature so I presume that the E1000 & E2000 have this feature. You say that E2500 & the E4200 have the feature. I presume that the E1200 v1 to E4200 v1 have the feature while E1200 v2 to E4200 do not have the feature. See new userguide for E1200 to E4200.
Greetings from Northern Ontario, Canada

Similar Messages

Which Linksys VPN Routers support Multicast forwarding

Which Linksys VPN Routers support Multicast forwarding / passthru I have remote SPA942 phones connected thru a vpn to a SPA9000/SPA400 system. After manual provisioning the phones work, but voice mail, auto provisioning, etc that use multicast do not work. VPN is using Netgear boxes which do not forward multicast. I'm going to switch to Linksys/Cisco VPN routers but want to make sure which models will do the multicast forwarding.
Thanks

I only no of 1 for sure and that is by downloading 3rd party firmware like DD-WRT, the WRT54G. See the below Link.
http://en.wikipedia.org/wiki/Wireless_Distribution_System
Ttech

Does rcapi on 800 series routers support CAPI version 2.0?

Does rcapi on 800 series routers support CAPI version 2.0? In that case: Is a certain IOS release mandantory?
Best Regards,
Martin Funke
K&K networks

Does rcapi on 800 series routers support CAPI version 2.0? In that case: Is a certain IOS release mandantory?
Best Regards,
Martin Funke
K&K networks

Does SRP series routers support VRRP?

Hi,
can somebody check if SRP routers support VRRP or HSRP? In documentation isn't this capability mentioned. I need make a backup to my main IOS based router.
Regards, Martin

Hi,
the console port indeed does not support RS232 modem control (data set ready/Data Carrier Detect (DSR/DCD), data terminal ready (DTR)). However, you cannot change the settings on the console port. You need to configure your modem to to ignore DTR and assert autoanswer. The associated Hayes-compatible commands are AT&D0 and ATS0=1, respectively.
Regards,
Nethelper

From which verison of oracle support the :NEW variable in trigger

A trigger using the :NEW variable can be compiled in oralce 10g but can't in oracle7 .
Does oracle 7 support the :NEW variable?

>
A trigger using the :NEW variable can be compiled in oralce 10g but can't in oracle7 .
Does oracle 7 support the :NEW variable?
>
You can answer questions like this yourself by always checking the documentation first.
NEW is not a variable, it is a correlation name.
See 'The Trigger Body' section in the Oracle7 Server Application Developer's Guide
http://docs.oracle.com/cd/A57673_01/DOC/server/doc/ADG73/ch9.htm
>
The Trigger Body
The trigger body is a PL/SQL block that can include SQL and PL/SQL statements. These statements are executed if the triggering statement is issued and the trigger restriction (if included) evaluates to TRUE. The trigger body for row triggers has some special constructs that can be included in the code of the PL/SQL block: correlation names and the REFERENCING option, and the conditional predicates INSERTING, DELETING, and UPDATING.
Accessing Column Values in Row Triggers
Within a trigger body of a row trigger, the PL/SQL code and SQL statements have access to the old and new column values of the current row affected by the triggering statement. Two correlation names exist for every column of the table being modified: one for the old column value and one for the new column value. Depending on the type of triggering statement, certain correlation names might not have any meaning.
A trigger fired by an INSERT statement has meaningful access to new column values only. Because the row is being created by the INSERT, the old values are null.
A trigger fired by an UPDATE statement has access to both old and new column values for both BEFORE and AFTER row triggers.
A trigger fired by a DELETE statement has meaningful access to old column values only. Because the row will no longer exist after the row is deleted, the new values are null.
The new column values are referenced using the NEW qualifier before the column name, while the old column values are referenced using the OLD qualifier before the column name. For example, if the triggering statement is associated with the EMP table (with the columns SAL, COMM, etc.), you can include statements in the trigger body similar to
IF :new.sal > 10000 . . .
IF :new.sal < :old.sal . . .
Old and new values are available in both BEFORE and AFTER row triggers. A NEW column value can be assigned in a BEFORE row trigger, but not in an AFTER row trigger (because the triggering statement takes effect before an AFTER row trigger is fired). If a BEFORE row trigger changes the value of NEW.COLUMN, an AFTER row trigger fired by the same statement sees the change assigned by the BEFORE row trigger.
Correlation names can also be used in the Boolean expression of a WHEN clause. A colon must precede the OLD and NEW qualifiers when they are used in a trigger's body, but a colon is not allowed when using the qualifiers in the WHEN clause or the REFERENCING option.
The REFERENCING Option

Which Adobe 3D apps support the Phantom Omni haptic input device?

Adobe is doing a lot of work in the 3D space - do any Adobe apps for 3D design (specifically for 3D printing, not animation) support the Phantom Omni haptic input device? Or what are the plans to add support? Now that GeoMagic has been purchased by 3D systems, I am hoping more software supports this device.

When you have the problem, note the exact time: hour, minute, second.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
Open LaunchPad. Click Utilities, then Console in the icon grid.
The title of the Console window should be All Messages. If it isn't, select
SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above. Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first. Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.

Which file is responsible for the BEA WL Console page

Can anyone tell me, which file is responsible for the BEA WebLogic Server
Administration Console web page?
For example, the URL for the Admin Console
http://<domainname>/console is being redirected to
http://<domainname>/console/login/LoginForm.jsp.

I would strongly discourage any modification of this as it would not be supported. Perhaps you should explain in more detail why you want to do this?
The files on WLS 10.0 appear to be here:
BEA_HOME\wlserver_10.0\server\lib\consoleapp\
Specifically in the webapp\WEB-INF\web.xml subdirectory you can see how things are set up to redirect in the login-config element.

Which X Series Model Has the Best Performance?

I am looking for the best performing computer in the X series.
Which model should I buy, if that is my criteria?
Thanks!
Richard

Agreed: x201 w/ SSD. 8GB would be great *if* you like to have a *lot* of things running simultaneously. The fact is, with 4GB and an SSD you have less latency on the pagefile. (Also it saves you a few hundred bucks!)

Which Linksys Wireless Routers support WDS?

includer 802.11G and 802.11N product
support WDS (wireless distribution) or repeate mode
I need AP+WDS hybrid mode
Message Edited by angel_nx on 07-14-2008 05:09 AM
Message Edited by angel_nx on 07-14-2008 05:09 AM

I only no of 1 for sure and that is by downloading 3rd party firmware like DD-WRT, the WRT54G. See the below Link.
http://en.wikipedia.org/wiki/Wireless_Distribution_System
Ttech

Plzzzz solve my problem my side scroll bar does nt appear due to which i have to face the problem in scrolling page up and dowen quicly.

i am using latest version of mozilla suddenly on mozilla searching page side scroll bar is not appearing due to which i have to face prob in scrolling the page which i see i am not understanding what has happened.plz solve this problem as soon as possible.

Here you go.

Cisco routers support ipv6 in OPNET?

Hi all,
my question is: which of cisco routers support ipv6 in OPNET Modeler simulator?
please, It's urgent.
Thanks in advance.

Hi Dan,
This is a funny community section to pose questions on the SOHO 97
It's End of Like annoucement was a wee while ago, in June 2006.
http://www.cisco.com/en/US/prod/collateral/routers/ps4866/prod_end-of-life_notice0900aecd804d5ad6.html
As you appreciate, the replacement for the SOHO97, the 800 series product supported IPv6.
I have taken the liberty , in relation to soho97, to copy a section from the IOS software release notes from the following URL;
http://www.cisco.com/en/US/products/hw/routers/ps221/prod_bulletin09186a00801ffda1.html#wp1003249
It states the following in relation to IOS version12.3(4)XG
"Baseline IPv6
Supported Platforms: Cisco 831, 836, and 837 Series Routers; Plus Images Only
Support of the baseline initiatives IPv6 features—providing IPv6 support to all Cisco 830 Series platforms. Further details in release notes."
Like yourself, no where can i see a reference to the SOHO 97 product supporting IPv6.
regards Dave

Does the 76xx routers supports EoMPLS without SIP installed?

Dear Sir!
Can you tell to me, does the 7600 series of routers supports EoMPLS without shared port adapters (SPAs) and SPA interface processors (SIPs)?
I.e. if we have 7606S-RSP720C-R, WS-X6704-10GE ports connected to backbone and
WS-X6408A-GBIC with WS-X6148A-GE-TX ports connected to our DataCenter
(without any SIPs and SPAs installed on board).
Can we make EoMPLS for such clients, which are should connected
to our DataCenter through remote CAT3750-METRO?
Best regards,
Maxim

Hello,
There are generally two modes of EoMPLS:
(1) PFC Based MPLS and related applications
mode
(2) WAN Based MPLS (SIP/SPA/OSM/ES20) and related applications mode
(1) Is only dependent on which Sup do you have
and generally works with most of the Ethernet (LAN) ports... If you have PFC-3B or later along with Sup-720, Sup-32 (which is PFC-3B) you can do it.
(1) Has some disadvantages - for example you cannot having L2 switching AND MPLS EoMPLS...
I.e. if you want to do local switching on Vlan 200 and part of the traffic to be switched part of the traffic to be EoMPLS you cannot do it without SIP/SPA/OSM/ES20
(2) In this case you need to check very well what you're looking for. These are expensive and they support MPLS and its Applications and even support VPLS, which is not possible with (1)....
I hope this answer your quesiton...

I have a new Linksys router. When I load the accompanying CD it informs me that it supports OS 10.5.8 or later, OS 10.6.1 or later, and OS 10.7 or later. I am running 10.9.2, which apparently isn't supported by this Router. Any suggestions?

I have a new Linksys router. When I load the accompanying CD it informs me that it supports OS 10.5.8 or later, OS 10.6.1 or later, and OS 10.7 or later. I am running 10.9.2, which apparently isn't supported by this Router. Any suggestions?

No they should be agnostic about what is behind them, but as to support for IP6, or whether any computers or tablets can use AC... and hasn't Apple's own units sometimes stop being supported with new Mac and new versions of OS X? seems so.
I said above, why would anyone install any kind of software to use a router? although Netgear's GEnie is or was installed on my systems that adds a nice way to log in and manage the router, so I have to take that back a notch.
Support for modems and ISPs is a concern, my modem is not certified fully with DOCSIS 3.0 or FIOS.
Look around and you can find routers having trouble with some network services like Airplay, printing and scanning, the software bundled with router.
However, ethernet chips, and the driver, can be a factor. Problems with Intel networking chip and high bandwidth streaming and not being able to handle the load when used by wifi euipment like notebooks and other devices.
I have only seen the LARGE number of complaints on MacBook forums about wifi issues to suspect something is wrong but not sure what. And those are people that depend on wifi I assume, though some could use their Thunderbolt equipped Mac to use ethernet to get around the problems. And I am seeing the same thing with some Windows users and maybe they all have common Intel chips???
MacBook Pro constantly losing wireless connectivity
I use Windows 8.1 primarily. I also don't know enough or as much to know "Why is the sky blue" either.
Just pass along this example:
If you're setting up a new PC for the first time, check if your router is fully compatible with Windows. Because of the new networking features in Windows (8.1), some older network routers aren't fully compatible and can cause problems. For a list of routers that are compatible with Windows 8.1 and Windows RT 8.1, go to the Windows Compatibility Center.
Anyone remember when 10.4.0 had so many issues with LAN that it could not be used, work on fix was going on and wasn't complete until 10.4.2/4.3 (and first time we got a new full 10.4.3 DVD because customers needed a reliable system.

Which MSI card supports the apple 30"

There are so many video cards out there and theories about which card will run this monitor, i almost wasted a lot of money trying to run the monitor on my 6800GT... it doenst i have tried both DVI ports.
Basically i want to know which MSI card supports the apple 30" does the new 7800? the old 6800 ultra? is my 6800GT messed?
A few things i can confirm are this, the monitor because of some signal issues DOES NOT support SLI at all.
I have read a few reviews that say the 7800GTX does not support this monitor - very disappointing i have to look for an older 6800 card.... - this is unconfirmed maybe someone can get back to me about this.
Anyways if MSI could tell us which card of theirs works i will turf my 6800GT and buy whatever is needed.

I can't be shure which MSI card support it, but reading the release notes from the latest nvidia drivers (77.22) I saw this:
The GeForce 6800 Ultra 512MB works in single card mode with Apple 30 inch HD Cinema panel. However, an issue has been discovered when running the GeForce 6800 Ultra 512MB card in SLI mode with an Apple 30 inch HD Cinema display. This is due to an interaction
between the GPU, the application, and the ability to scale to nonnative panel resolutions of the Apple display.
All GeForce 6 series GPUs will work with Apple 23 and 20 inch HD Cinema displays in single GPU mode. NVIDIA recommends using the GeForce 6800 Ultra 512MB with the Apple 30 inch HD Cinema Display line only in non-SLI modes.
Edit here:
Modes Supported for High Resolution Displays:
Display:
*Apple 30” Cinema HD Display (Dual link DVI)
Hardware Requirements:
*All High-end Quadro FX (see list of products in “Quadro FX Family of High End GPUs”
* GeForce 6800 with 512 MB
Maximum Resolution:
2560x1600 @ 60Hz
Source: 77.22 Forceware Release Notes.
I guess that your card (6800 GT Non Ultra) doesn't support it. Maybe a new drievers release will fix this.

Does the SONY VAIO F Series SVF15412CXB support dual channel memory?

Does the SONY VAIO F Series SVF15412CXB support dual channel memory? Or does it only have one slot?
I'm curious if I can put a second stick of RAM in there for dual channel performance.

Hi Mark, Thanks for the response. Can you please double check that for me, or post a link to the documentation where you saw that? I asked this question on Newegg, too, and one of the respondants heard differently:
"i found out from sony that there is only 1 slot cause i was gonna get 1 more 4GB stick of ram for 8Gb. So iwas upset about that cause i have to get 8GB now and it costs 100$ for an 8Gb stick of ram on ebay. So this ram is expensive. So im sticking with 4Gb for now. This is a very good laptop though. I use it primarily for minecarft and steam and i get around 100 fps on minecraft so its good. I hope this helps." It's just confusing because other laptop advertisments I've seen openly stated how many RAM slots the computer had and how many were used upon purchase. I haven't found anything like that which makes me think that there's only one slot for RAM. Thanks,Gremark

Which E series routers support the Wireless_Advanced.asp hidden page?

Similar Messages

Maybe you are looking for