Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

I have 4 GLC-T SFPs of various models. For some reason 2 of them does not work. IS not recognised by the FI. I have tried moving them around to other ports, and making sure I only use port 1 to 8 doing so. Are they faulty or should I get a specific GLT-C model?
SFP 1: 30-1410-02
SFP 2: 30-1410-03
The 2 other working SFPs I do not have the part numbers here.

FI6120XP-B(nxos)# show interface eth 1/5 transceiver details
Ethernet1/5
    transceiver is present
    type is 1000base-T
    name is CISCO-AVAGO
    part number is ABCU-5710RZ-CS2
    revision is
    serial number is AGM124227QP
    nominal bitrate is 1300 MBit/sec
    Link length supported for copper is 100 m
    cisco id is --
    cisco extended id number is 4
   Transceiver calibration is invalid
FI6120XP-B(nxos)# show interface eth 1/7 transceiver details
Ethernet1/7
    transceiver is present
    type is 1000base-T
    name is CISCO-METHODE
    part number is SP7041_Rev_F
    revision is F
    serial number is 00000MTC145004L4
    nominal bitrate is 1300 MBit/sec
    Link length supported for copper is 100 m
    cisco id is --
    cisco extended id number is 4
   Transceiver calibration is invalid
and this interface output:
FI6120XP-B(nxos)# show interface eth 1/5
Ethernet1/5 is down (SFP validation failed)
Hardware: 1000/10000 Ethernet, address: 000d.ecfb.ae0c (bia 000d.ecfb.ae0c)
Description: U: Uplink
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
auto-duplex, 10 Gb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped never
Last clearing of "show interface" counters never
30 seconds input rate 0 bits/sec, 0 bytes/sec, 0 packets/sec
30 seconds output rate 0 bits/sec, 0 bytes/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 0 bps, 0 pps; output rate 0 bps, 0 pps
RX
    0 unicast packets 0 multicast packets 0 broadcast packets
    0 input packets 0 bytes
    0 jumbo packets 0 storm suppression packets
0 giants      0 input error 0 short frame 0 overrun   0 underrun      0 watchd
og 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    0 unicast packets 0 multicast packets 0 broadcast packets
    0 output packets 0 bytes
    0 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble
    0 Tx pause
0 interface resets
FI6120XP-B(nxos)# show interface eth 1/7
Ethernet1/7 is down (Administratively down)
Hardware: 1000/10000 Ethernet, address: 000d.ecfb.ae0e (bia 000d.ecfb.ae0e)
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
auto-duplex, 10 Gb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped never
Last clearing of "show interface" counters never
30 seconds input rate 0 bits/sec, 0 bytes/sec, 0 packets/sec
30 seconds output rate 0 bits/sec, 0 bytes/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 0 bps, 0 pps; output rate 0 bps, 0 pps
RX
    0 unicast packets 0 multicast packets 0 broadcast packets
    0 input packets 0 bytes
    0 jumbo packets 0 storm suppression packets
0 giants      0 input error 0 short frame 0 overrun   0 underrun      0 watchd
og 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    0 unicast packets 0 multicast packets 0 broadcast packets
    0 output packets 0 bytes
    0 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble
    0 Tx pause
0 interface resets
But regarding "the transceiver calibration invalid" status, I get the same output for my etherchannel in linked state:
FI6120XP-A(nxos)# show interface eth1/1 transceiver details
Ethernet1/1
    transceiver is present
    type is 1000base-T
    name is CISCO-METHODE
    part number is SP7041
    revision is E
    serial number is 00000MTC1250008A
    nominal bitrate is 1300 MBit/sec
    Link length supported for copper is 100 m
    cisco id is --
    cisco extended id number is 4
   Transceiver calibration is invalid
FI6120XP-A(nxos)# show interface eth1/2 transceiver details
Ethernet1/2
    transceiver is present
    type is 1000base-T
    name is CISCO-METHODE
    part number is SP7041_Rev_F
    revision is F
    serial number is 00000MTC145004BK
    nominal bitrate is 1300 MBit/sec
    Link length supported for copper is 100 m
    cisco id is --
    cisco extended id number is 4
   Transceiver calibration is invalid

Similar Messages

How do I upload to Facebook in High Resolution using my iPhone. Do I need an app? Which ones are best for the job? (I know how to do it on a PC :) )

How do I upload photos to Facebook in High Resolution using my iPhone. Do I need an app? Which ones are best for the job? (I know how to do it on a PC )

100pat wrote:
Thanks, I can do it fine from my Windows desktop PC, I just want to know how to do it from an iPhone4
Like I said before ask facebook or look at their support site to see if that is even a feature.

Where to see activities, which are created for the campaign with target group

Hi
I have created a Communication Method in SPRO -> CRM -> Marketing -> Marketing Planning & Campaign Management -> Campaign Executtion - Define Communication Method : Activity has been configured
Activities are not appearing after creation of campaign with target group.
Where to see activities, which are created for the campaign with target group?
Regards
Hamid

Hello,
alternatively to check table CRMD_ORDERADM_H directly you can use the related transactions search for the campaign:
This should bring all activities generated by the campaign. If this is empty first check the job log of the campaign execution job again:
This gives information if any target group members have business transactions created. If the log does not contain the required information you can debug from SM37. The business transactions (activities, leads, sales orders) are generated from function module CRM_MKTTGGRP_PROC_CREATE.
best regards,
Johannes

None of the network adapters are bound to the Netmon driver.If you have just installed, you may need to log out and log back in order to obtain the proper rights to capture. Please refer to the product help for more information.

Hi,
To analyze Lync issues I have installed these applications in my windows 7 x64 laptop
1) network monitor 3.4
2)Lync network monitor parser
3)nmdecrypt2.3
4)network monitor parser3.4
Installtion got completed successfully but when I try to start capture I get this error everytime.......
"None of the network adapters are bound to the Netmon driver.If you have just installed, you may need to log out and log back in order to obtain the proper rights to capture. Please refer to the product help for more information"
I read many technet articles and other blogs but that didn't solve this issue. I tried things like
A) Run as administrator
B) nmconfig /install in cmd
So could you please help me how I can fix this issue?
Regards,
Ajit

Seems our driver didn't get installed. What you see when you type "sc query nm3" from a command prompt?
Thanks,
Paul

Adobe Captivate has encountered a problem and needs to close. We are sorry for the inconvenience.

I am trying to use Adobe Captivate 5 and I am receiving this message when trying to open the application,
"Adobe® Captivate® has encountered a problem and needs to close. We are sorry for the inconvenience."
Can you explain how this issue can be resolve!?

Hi there,
On which operating system are you using Adobe Captivate?
Please recreate the preferences of Captivate, following is the location of Captivate Preferences:
Windows 7: C:\Users\[user name]\AppData (hidden folder)\Local\Adobe\Adobe Captivate 5 folder
Windows XP: C:\Documents and Settings\[user name]\Local Settings\Application Data\Adobe\Adobe Captivate 5 folder
Mac: /Users/[user name]/Library/Preferences/Adobe Captivate 5 folder
rename Captivate 5 to Captivate 5_old
and then try to launch Captivate 5
Thanks.

Dynamiclinkmanager has encountered a problem and needs to close. We are sorry for the inconvenience

I get this message when opening Prem. ele 9 trial. "dynamiclinkmanager has encountered a problem and needs to close. We are sorry for the inconvenience."
Prem opens but does not work well. When I load a VOB file it comes in as audio only. Prem. barely works. Any suggestions?
thanks

So which issue do you want to deal with?
With this many problems, it appears that your computer is not set up well to work with this program. I recommend you contact Adobe Tech Support and have them see if they can troubleshoot it. You may need more help than we can give you on this forum. Sorry.
(It might also help to know what operating system you're working on, of course. Macs have a known issue with the dynamiclinkmanager file, as discussed in this thread: http://forums.adobe.com/thread/634929 )

If you are looking for the Project Siena Functional Reference ...

Hello,
If you are looking for the functional reference direct link
http://siena.blob.core.windows.net/beta/ProjectSienaBetaFunctionReference.html
Regards
StonyArc

Hope you are refering it to the actual page, which you invoke for any cfm/cfc request then yes, its extension would be .cfm/.cfc page but if you are refering it to its corresponding encoded pages from {ColdFusion10}\cfusion\wwwroot\WEB-INF\cfclasses then its extension would be .class.
Regards,
Kaif Akbar

I can record and hear me recording through the computer's built in mic, but can't get the external mic and headphones to work., The preferences are set for the external mic and headphones...

I can record and hear me recording through the computer's built in mic, but can't get the external mic and headphones to work., The preferences are set for the external mic and headphones...

What operating system are you using? Is it on a Mac or a PC? Which preferences are set for external mic/headphones, Audition's or the computers?

What anti-theft solutions are best for the ipad?

Hello,
I would like to know which anti-theft solutions are best for the IPad. I am ordering several for work and I would like to know. Thanks.

It depends upon how far you are willing to go. Keeping it locked in a bank vault comes to mind but I suppose you want more flexibility. Are you talking about physical attachment or just something to discourage a thief, or something to protect data integrity in case of theft? Realize that in many situations somebody may steal something and only later check if it has any value. If it doesn't they will toss it in the nearest river, but you've still lost it. As for iPads, a thief can reset one and it's like new.
Find My iPad - http://www.apple.com/ipad/icloud/#find - has to be enabled before device is lost. It also requires the device be on and connected to registered WiFi network or data service, and not having been restored by the finder (if it was really stolen then the thief has probably restored it). If you have activated the "Find My" feature, go to https://www.icloud.com or use the Find My iPhone app - http://itunes.apple.com/us/app/find-my-iphone/id376101648?mt=8
Setting up iCloud (requires iOS5) - http://www.apple.com/icloud/setup/ios.html - includes activating the 'Find My' feature.
Kappy's missing idevice recommendations 09/2012 - https://discussions.apple.com/message/19569712

I got my adobe creative license but the app are asking for the serial number. What can I do?

I got my adobe creative license but the app are asking for the serial number. What can I do?

Welcome to Adobe Forum,
Creative cloud do not need a serial number. it will be using your Adobe ID on which you have purchased the creative cloud membership.
So you need to login with your Adobe ID and password to activate the cloud membership.
Log out & log back in of the CC Desktop App.
In case it is not signing in successfully please try the following:
I don't know which operating system you are working on so i am giving you some steps windows and MAC OS:
   Windows:
   In windows 7 navigate to following location:
     /windows/system32/drivers/etc
   1. look out for "Hosts" file
   2. Open it with notepad
   3. Check if you have any entry for Adobe
   4. Remove the entries and try again launching any product from CC
   Mac:
   1. Please click on "Go" and navigate to /private/etc
   2. Open "hosts" file and check out for any entries for Adobe.com
   3. Remove the entries and save the file
   4. try again launching any product from CC
You can refer :
http://helpx.adobe.com/creative-cloud/kb/ccm-prompt-serial-number.html
http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-i ssues.html.
Please let us know if it worked.
Regards,
Rajshree

PURCHASING-How to change the next approver for the Purchase Requistion(PR)-

Hi All,
Could you please let me know how to change the next approver for the Purchase Requistion(PR) from User "X" to "Y", as Y was manager of "X" and 'X' left the organization. how can i acheive this? can you please let me know the process ?
Thanks,

Hi,
You have not mentioned the version you are using (11i or R12).. Are you using iProcurement... ? Are you using positional or Employee-Supervisor hierarchy..?
Your question : How to change the next approver for the Purchase Requistion(PR) from User "X" to "Y", as Y was manager of "X" and 'X' left the organization.
Ans: You can achieve this through below workarounds
- Through *"Mass Update of Requisitions" functionality* (Conc. request) you can update the Approver name from User "X" to "Y" for existing PRs.
- Replacing the Supervisor name of the requestor/requisitioner in the HR record (assignment) from User "X" to "Y"..
Hope it helps.
Kind Regards,
S.P DASH

Adobe Photo Downloader has encountered a problem and needs to close. We are sorry for the inconvenience. Error Code: c0000005 Address: 76f73ac3 I clicked on the OK button and the downloader closed. I then tried to download from the organizer. I

Photoshop Elements 12
Adobe Photo Downloader has encountered a problem and needs to close. We are sorry for the inconvenience.
Error Code: c0000005
Address: 75e32f71
I clicked on the OK button and the downloader closed.
I did a search on this error code (c0000005) and there seems to be a workaround but no solutions, why is this? I ask that because this problem seems to be years and years old, going back to at least 2005 (do the math that is 10 years).
I don't even have the Camera hooked up and I get this error on download. I redownloaded everything and reinstalled. I allso saw the AVI issues reported with this proble so i updated Quicktime though without the camera being hooked up when I get this error I didn't expect that to work. I tried support and they wouldn't help because I bought it in March this year. Pretty frustrating as I have re-purchased Elements about every 2 years. I think I might need a new CODEC? I had this problem on an Earlier version And I seem to remember that being the Fix but this may be something completely different

I finally found that it was missing a picture so the Catalog was "corrupted". I just deleted the picture and it started working.
I hate Adobe and their total lack of support - thanks for nothing Adobe . Also get this - they offered me to upgrade to 13.0 ( My 12.0 is only 6 months old but they still don't support it on errors. Only install errors!
I have upgrade and repurchase this product 4 times now. I will find something else next time!

Adobe Reader 8.0 has encountered a problem and needs to close. We are sorry for the inconvenience

Ver 8 installed fine but can't get it to launch from any application. Have tried going back to earlier versions (6.1,6.2,7) but the same problem occurs.
Same error message each time:
"Adobe Reader 8.0 has encountered a problem and needs to close. We are sorry for the inconvenience"
AppName: acrord32.exe AppVer: 8.0.0.456 ModName: acrord32.dll
ModVer: 8.0.0.456 Offset: 00020916
Tried every troubleshooting tip in the Support Knowledgebase to no avail.
Have been using Reader for years with never any problems and now I can't seem to get this fixed after numerous hours.
Any suggestions would be appreciated. Is there a free support line I can call or is it paid support only?
Thanks,
Dee

Like others my problem was Adobe Reader 8.1.2 died terribly and with a buggy stench with the following error:
AppName: acrord32.exe AppVer: 8.1.0.137 ModName: msvcr70.dll
ModVer: 7.0.9466.0 Offset: 000013d6
RESOLUTION ON XP SP2
1. Control Panel, Users
2. Create a new user account NewUser (for example)
3. Start, Log Off
4. Switch Users to the NewUser
5. Wait the mini eternity for new user to be set up.
6. Start Adobe Acrobat 8.1.2 and you will see a red splash screen along with some license updating things.
7. Adobe 8.1.2 now starts fine under NewUser
8. Switch back to your regular user name. Start, Log off, Switch Users
Now a note to Adobe. Do you folks really have to make this such a frickin pain to get working? Do you at Acrobat have any idea of how much time we users blow and how much of our lives pass by while we try to re-download and work with this product? You are directly responsible for a small slow down in the world economy by this. Get the hint.... create an 8.1.3 that omits the secret code steps above.
The only thing that kept my sanity during this were nice songs on channel 86 on SIRIUS. Thank you SIRIUS.
Thanks,
Jim

Firefox.exe has encountered a problem and needs to close. We are sorry for the inconvenience. I have been using firefox for years. I installed the latest version of Firefox. It worked fine for several days. Now I get the above message each time I try to s

firefox.exe has encountered a problem and needs to close. We are sorry for the inconvenience.
I have been using firefox for years. I installed the latest version of Firefox. It worked fine for several days. Now I get the above message each time I try to start Firefox, even in safe mode. i have checked with latest antivirus softwere also.. i didn't find any thing suspicious.
== This happened ==
Every time Firefox opened
== after loading firefox 3.6.6 ==
== User Agent ==
Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/533.4 (KHTML, like Gecko) Chrome/5.0.375.99 Safari/533.4

I was having this problem few days ago,and I have fixed.Try this steps-If you have AVG antivirus so go on firefox>Tools>Add On and Disable AVG safe search and AVG tool bars too.Then restart computer.

"iTunes has encountered a problem and needs to close. We are sorry for the inconvenience."

please... help. i can't to sync my tones to my ip5s. i don't know why....
"iTunes has encountered a problem and needs to close. We are sorry for the inconvenience."
"Please tell Microsoft about this problem."
And bla bla bla... Already send error report, but everytime i want to sync tone to my phone that toolbox will appear.
So frustrated.
So please help me....T____T

hi David!
okay, it's time to check if you have a weird registry problem. (the problem i'm thinking about produces the same error message.)
we diagnose that by creating a new user account (with full administrative privileges). you can do that in your "user accounts" control panel. there's help documentation on it to the left of the screen. while you're in there, also switch off "fast user switching" in your logging-on preferences.
now log on to the new user account. can you successfully launch itunes from inside there?
keep us posted on your progress.
love, b

Which GLC-T 1 Gb adapters are approved for the XP6120 FI?

Similar Messages

Maybe you are looking for