Which image for 3650 switch supports bgp

Hi Guys. Anyone know the iOS XE image that supports BGP for the Catalyst 3650 L3 switch? Or how to find that information - I keep getting an "image does not support bgp" error. Thanks.

Hi,
If you want to run BGP on 3650 series switches, you need to have IP Services license.
see table-3 in this link:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-3650-series-switches/qa_c67-729531.html
HTH

Similar Messages

Which tools for the Mac support Secure Erase (SE)

Note: I'm not talking about what Disk Utility allows you do to go by overriting data. I'm talking about a full wipe of areas not usually accessible by the user. For instance the X-25M like any other ATA device supports SECURE_ERASE which will erase more than just the data area of the drive.
So far HDDERASE for the PC is the only tool I know of that issues this command.
Is there any C code that exists that issues this command that allows this command to be issued on Macs and machines that don't support what's called "legacy IDE mode?"

The most secure is zeroing an entire hard drive:
http://support.apple.com/kb/HT1820
Note it won't work on hard drives that have been partitioned. Therefore it really does the ENTIRE hard drive.

Which ios for catalyst 4500 support wccp?

hi everybody
could you pls tell me, which ios I can use for 4500 series that could be support WCCP?
thanks

Hi
As per the datasheet WCCP is not supported in 12.2(25)SG which is the latest available code for 4500.
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_5184.htm#wp363642
But you can make use of AGM module which does supports as mentioned in product datasheet relased ..
http://www.cisco.com/en/US/products/hw/modules/ps2957/ps5288/index.html
regds

Which Image should we need for the below model router 2951 to support 4 Byte ASN number ?

Hi All,
Which Image should we need for the below model router 2951 to support 4 Byte ASN number ?
CISCO2951/K9
Cisco 2951 w/3 GE 4 EHWIC 3 DSP 2 SM 256MB CF 512MB DRAM IPB
PWR-2921-51-AC
Cisco 2921/2951 AC Power Supply
CAB-ACSA
AC Power Cord (South Africa) C13 BS 546 1.8m
HWIC-BLANK
Blank faceplate for HWIC slot on Cisco ISR
ISR-CCP-EXP
Cisco Config Pro Express on Router Flash
MEM-2951-512MB-DEF
512MB DRAM (1 512MB DIMM) for Cisco 2951 ISR (Default)
MEM-CF-256MB
256MB Compact Flash for Cisco 1900 2900 3900 ISR
SM-S-BLANK
Removable faceplate for SM slot on Cisco 290039004400 ISR
SL-29-IPB-K9
IP Base License for Cisco 2901-2951
S2951UK9-15501T
Cisco 2951 IOS UNIVERSAL
EHWIC-1GE-SFP-CU
EHWIC 1 port dual mode SFP(100M/1G) or GE(10M/100M/1G)

> Can someone suggest ?
a forum is no realtime-communication ... ;-)
For the ISR G1, it was supported from 12.4(24)T, so I would assume that your ISR G2 has this feature if you are running 15.x.
EDIT: The Feature-navigator says that it's supported starting with 15.1(2)T.

Switch support for NAC CCA for 6500 series switch

per the 4.0 document "switch support for Cisco NAC" there is a note that says
Catalyst 6000/6500 on IOS do not support mac-notification
Does this mean you cannot deploy layer 2 OOB mode, as snmp notification to the CAM will not happen with the 6k platform?

Probably, the configuration guide will give you better idea about your problem.
http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_guide_book09186a00803f5611.html

Which axi version is the supported and compatible version for JDK1.4?

Hi,
Can any body tell me Which axi version is the supported and compatible version for JDK1.4.Thanks in advance.
Regards,
Lokesh Kumar Pattajoshi

Hi Jürgen
Please be advised that the customer is correct.
Please see the following note:
539188 TREX installations for E-Selling
For all E-Commerce and ICSS scenarios using
SAP Web Application Server Java 6.40 TREX 6.1. is recommended.
Hope this will be of assistance.
Kind regards Peter
Edited by: Peter Murphy on Jan 23, 2009 3:01 PM

I am looking into Lightroom (Creative Cloud) to allow a Team Member access my Catalog to keyword search which images will work for our Social Media platforms.

I am looking at LR Creative Cloud to allow a Team Member access my catalog so she can keyword search which images will work for our social media campaigns. My catalog has both personal and business images (which are in separate folders), however, I only want them to access the business images. What is the best way to do this?
and a second question as I am new to the Cloud LR product. I am assuming that my images still stay on my external drive...how am I or her able to view these images if I am out of town on another computer?

My catalog has both personal and business images (which are in separate folders), however, I only want them to access the business images. What is the best way to do this?
I think the only way in Lightroom to make this happen is to use two catalogs, one for business and one for personal, and then prevent access to the personal catalog via putting it on a disk or location that your team member does not have access to.
I am assuming that my images still stay on my external drive...how am I or her able to view these images if I am out of town on another computer?
Situations like this require you to put the catalog file AND photos on the external HD and then move the external drive to whatever location and whatever computer is needed. An alternative is to put the photos on a network drive and the catalog file on a local disk and access the catalog locally and the photos via network, but that limits you to using a single computer.
I am looking at LR Creative Cloud to allow a Team Member access my catalog so she can keyword search which images will work for our social media campaigns.
As far as I know, this does not require Creative Cloud, nor does Creative Cloud help in this situation. Furthermore, if you are thinking about a situation where you and your team member have simultaneous access to the catalog(s) of interest, this is not possible in Lightroom. Lightroom is a single user application.
If you are interested in a true multi-use application, where more than one individual can access a catalog at the same time, you might want to look at Daminion. Note: I am not endorsing or recommending Daminion, as I have never used it; I simply point out the that it has the feature being discussed.

Linux Fencing Support for iSCSI switches...

Do any of the Cisco iSCSI network storage switches support Linux fencing agents? If so, which ones.
Thanks,
-Rich

There is no fencing control (port blocking) capabilities on the MDS9000 iSCSI interfaces. Port blocking control by a fencing agent is not available on the Line Card FC ports.

Which way to get image for webi report?

Hi,
I have to add image to webi report. So any way is there for adding image for webi intelligence.

check this thread:
Adding an image (logo) to webi report

Does 6509 switch support CDP bypass feature when interface configured with IEEE 802.1X?

hi, guys
we are deploying CISCO video endpoints (SX 20) for out customers, as the access switch is 6509 which version is 12.2(33)SXJ5
following is the configuration on the interface, but the endpoints can not pass through the authentication, and also it can not get IP address
from DHCP server , so just want to know whether if the 6509 switch support CDP BYPASS feature?
interface GigabitEthernet x/xx
switchport
switchport access vlan 400
switchport mode access
switchport voice vlan 409
authentication host-mode multi-domain
authentication port-control auto
authentication timer reauthenticate 65535
authentication timer inactivity 120
authentication violation restrict
dot1x pae authenticator
dot1x timeout tx-period 5
dot1x timeout supp-timeout 10
spanning-tree portfast edge

What image are you running now ? I am facing the same problem in 8.4(1) workround : upgrade to 8.4(2)GLX.

How can i upgrade system IOS images of routers, switches and firewalls

Hi,
I am very much surprised and less of understanding yet how Cisco's licensing program or IOS upgrades are done. I have many routers, switches & ASA's of whom i wan to upgrade the IOS's but i cannot do so. How ever i can download those images from internet but i want to know how can i do this from Cisco as i don't want to trust those IOS's available over internet.
As per my study what i have found that i need to have Cisco Service Contract number for that devices so that i can download updated IOS Images for them.
Someone kindly explain what are the best methods for the above requirements.
Regards
@Mohammed

You're correct regarding a service contract. Cisco calls this Smartnet support. It includes both hardware support (i.e. returns for failed hardware), software support (including right to download and upgrade your software) and technical assistance (via the Cisco TAC). Smartnet is charged separately for each covered device. Once you have it, your cisco.com userid needs to be associated with your service contract number. Doing that will then allow you to download the software from cisco.com. (There are some very limited cases in which you don't have to have a support contract - mostly when there is a security advisory (PSIRT) indicating the Cisco software was flawed as it was initially released.)
Every product (or product family) has a product support page on cisco.com. That page includes release notes, configuration guide, users guides, and a link to software downloads for that product. Start by reading the release notes and determining which (if any) upgrade is appropriate for your product. Then you can download and upgrade the software as necessary.

Create a UK based image for VMs

Hello,
We are trying to install an application which requires a UK (en-GB) locale, however have not had much success in trying the default images, then converting them to UK regional settings (via group policy, copy settings..." function in Region and
Languages or via the registry).
Given we can't get the out-of-the-box images working, we have turned to creating the basic VM locally stating with UK settings, then uploading the image.
We assume that once sysprep has been run and the image provisioned within Azure, the locale will be configured to US. Based on this, we are trying to use unattended.xml to set everything to UK settings, so the machine never is configured to US at any
stage. On doing so, the provisioning eventually fails. Reading around the subject, articles state to delete unattended.xml and other articles state that the unatteneded.xml can conflict.
The question is: Can certain settings be placed in the unattended.xml and if so, can the regional settings be placed here (does anyone have a successful example file used in Azure)?
If the unattended.xml can not be used to achieve this, can anyone suggest (ideally with detailed steps) how we can achieve a VM with UK based regional settings (not just a US one which we then try to update via registry or the "copy settings..."
function in Region and Languages)?
With thanks,
Richard

Hi Richard,
Azure uses an unnatend.xml file as part of the deployment process for new VMs. Currently it is not possible to upload your own unnatend.xml file
to choose roles, features of settings to be added during deployment.
I recommend you to submit your requirement in the link below:
http://feedback.azure.com/forums/34192--general-feedback
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Background-image for commandToolbarButton

Hi,
I want to skin af:commandToolbarButton similar to standard skinned commandbutton.
I managed to change the background-image for the link-section, but there seems to be a other section with a background-image which is a little bit bigger than the link-section.
But I can't find how to e.g. disable this background-image when mouse is moved over the commandtoolbarbutton.
Here my CSS definition for the hover-action:
================================
af|commandToolbarButton:hover,
af|commandToolbarButton::link:hover,
af|commandToolbarButton::text:hover
background-image: none;
border : none;
============================
What's my mistake?
regards
Peter

Hi,
if you extend an existing skin then you need to use
-tr-inhibit: background-image
Here's a list of the valid CSS
af|commandToolbarButton
Style on the root element of the af:commandToolbarButton component. This style includes the .AFDefaultFont:alias style. CommandToolbarButton supports further styling with the :hover, :depressed, :selected, :disabled, :text-only and :action-disabled pseudo-classes.
af|commandToolbarButton::access-key
Style on the access key for the label of the af:commandToolbarButton component. For example, underline the access key. Includes .AFFormAccessKeyStyle:alias.
af|commandToolbarButton::link
Style on the button link on the af:commandToolbarButton component.
af|commandToolbarButton::text      Style on the button text on the af:commandToolbarButton component.
af|commandToolbarButton::dropdown-cell
Style on the cell containing the dropdown icon used for the popup button of the af:commandToolbarButton component.
af|commandToolbarButton::dropdown-icon-style
Style of the icon used for the popup button of the af:commandToolbarButton component. The icon is specified as a background-image in this key. To override the default icon, set -tr-inhibit: background-image in the dropdown-icon-style and define the override icon for the dropdown-icon.
Frank

Unable to select multiple images for upload

I have Windows 7 Pro and FF 9.0
I have an online store and am always uploading product photos for items I have listed. I recently switched from XP Pro to Windows 7 Pro. I had no issues with XP. However, now that I have Windows 7 Pro I am unable to select multiple images for upload when using FF. I can only select one image at a time.
The issue is unique to FF. I have tried in several other browsers, and FF is the only one that I am unable to select multiple images from.
I had FF 8.0.1 and upgraded to 9.0... hoping that would resolve the issue. It did not. I have restarted my computer several times which has also had no effect.

Hi,
Welcome to the  Discussions
I see it is about 6 hours since you posted, so I guess you will get this when you wake. (I'll be sleeping then)
This would be better asked in the forum for Using Leopard inside the Leopard Category sating which browser and which site it was.
(it probably made lots of sense to you when you were typing it but it seems a little short in facts or workable info.)
8:43 PM Wednesday; March 24, 2010
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
Message was edited by: Ralph Johns (UK)

Missing thumbnail images for AVCHD files

I never had this problem before.
In the past I would import AVCHD (*.mt2s) video files to the oganizer using Premiere Elements 7.
Then I would open Photoshop Elements 7 and the video files I just imported in Premiere Elements 7 would display their thumbnails just fine.
NOW, these thumbnails do not display.
AVCHD files that I had previously imported still display their thumbnail, but any NEW AVCHD files do not display their thumbnail images; it just displays a default video thubmbnail graphic.
Furthermore, if I select "Update thumbnail" from the context menu of a previously imported AVCHD file with a thumbnail, then the thumbnail image goes away and siaplays the default graphic.
(PLEASE NOTE: when I click the default thumbnail image, it opens the video previewer successfully. So the answer is not that the video file is missing and therefore needs to be reconnected to regenerate the thumbnail image. So else is wrong here.)
How can I get the thumbnail feature to work properly? It works fine in Premiere Elements; the thumbnails images for both new and old imported files display just fine in that program, which is what I used to be able to see in Photoshop Elements. Why is PSE7 not displaying these video thumbnail images?

I have solved this issue myself a month or two ago and forgot to report my findings.
I alspo have a Canon HD camcorder so this was a major issue for me.
The way to resolve this issue (at least in my case) was to download a codec pack like k-lite. Do a google search for the codec pack or follow this link:
http://www.codecguide.com/download_kl.htm
When I installed the codec pack, I think I had to make sure M2TS files were selected within the installation wizard so just be aware of that.
Another way to resolve this issue is to upgrade to Windows 7. After I upgraded to Windows 7, I did not have to re-install the codec. I think Windows 7 has native support for AVCHD files.
I hope this helps. If it does, please report here if you encounter anything of note worthy since the details of this process are no longer fresh on my mind.

Which image for 3650 switch supports bgp

Similar Messages

Maybe you are looking for