Which PCI SATA card for B&W G3?

I just picked up a 400GB Seagate SATA drive and I would like to install it into my B&W G3. Does anyone have any recommendations on which SATA PCI card to buy? I have found prices from $22 to over $100. Most of those on the low end when you look at the specs always reference the minimum requirements for a PC, but nothing for a Mac.
If the card is PCI compliant, shouldn't it just be plug and play?

SIIG's SC-MP4A12 UltraATA 133/100 Pro is what I went with - should retail about 65-100$. Be careful with lower priced models as the bus speed may be lower (in my head, this being the speed at which data is transfered through the harddrive into the system and back. Slower might be OK but there's little point in getting a drive that you are at pains to get info to and from. And the card MUST be mac compatible - no it isn't just plug and play (I learned that the hard way assuming a Belkin would be since they make so much mac stuff). Others to look for include ACard. Also keep in mind there are serial ATA and ultra ATA cards - get a drive that matches the card and vice versa.
So far the SIIG card works but I'm having some hiccups and kernal panics (probably an addressing issue - it takes a bit longer to start up the computer as it looks for the OS across all the drives and something might be mismatched by me right now). Also, leave your OS-based drive attached/connected to the motherboard connection (though you can have back up startup disks attached to the IDE controller - that's another name for the card, right) since it looks there first on start-up it appears. Hope that helps.
Andy

Similar Messages

Should I Get A PCI Sata Card For Internal Drives

I'm transferring Files from old G4 to a new G5 and it's taking forever. The sata drives seem to work slower. When I transfer the same way(Firewire)on my G4 it's much faster. Someone said to get a PCI sata card and hook up my internals to that instead of the factory connection. That it's faster that way. I'm going to have to burn to dvd and transfer that way, but it seems to defeat the purpose. Any suggestions are appreciated.
G5 Dual Core 2.0 with 2.5 GB and 2 250 Drives

Come to think of it, the last time I needed to transfer some media from my G4 to G5, the quickest and easiest way (mind you they are in separate rooms), was to pop out the G4 drive and use one of these cheap IDE USB adapters. Since the G5 is USB2, the process was pretty quick.
My guess about the G5 in target mode is there must be some kind of overhead, but the SATA is FAR and away faster than the FW connection between them, so a SATA card won't help.
Shane Ross and I are currently using "popsicle stick" internal RAIDs in our G5s. See this thread:
http://discussions.apple.com/click.jspa?searchID=-1&messageID=2162848
Patrick

Which E-SATA card for new Mac Pro??

I have the new Mac Pro 8-core 2.26GHz (Nehalem) and need to connect my two Western Digital drives via their E-SATA ports for video editing.
I bought a Sonnet Tempo card, having being led to believe this was one of the better cards, but sadly when I installed it, it didn't work. Careful reading of the small print on the Sonnet website informed me it wasn't actually compatible with the new MacPro.
Could someone recommend a E-SATA card (2 ports) for use with my system. I'm struggling to find one.
Cheers
Keith.

I have the new Mac Pro 8-core 2.26GHz (Nehalem) and need to connect my two Western Digital drives via their E-SATA ports for video editing.
Hi,
Unfortunately, the WD MyBook is not ideal for video editing. The enclosures use a bridge board that splits the connection between USB/FireWire/eSATA. This type of connection usually slows eSATA performance and is not compatible with all eSATA controllers. As a result, starting with the WD MyBook puts eSATA users at a disadvantage.
I agree with hatter that you would be better off with the Sonnet Tempo E4P and the FirmTek SeriTek/5PM. You could still use the WD MyBook as a backup device.
http://www.amug.org/amug-web/html/amug/reviews/articles/sonnet/mac-pro/
http://www.amug.org/amug-web/html/amug/reviews/articles/firmtek/5pm/
http://firmtek.stores.yahoo.net/sata5pm.html
FirmTek sells a 2-port card with the SeriTek/5PM, but as it is Silicon Image SiI3132 based, performance will be limited to approx. 135MB/sec. with a single cable. If a dual bay direct connect enclosure like the SeriTek/2EN2 is used the RAID 0 performance will be approximately 150MB/sec. when the volume is empty.
Moving up to the Sonnet Tempo E4P can provide 210MB/sec. write and 250MB/sec. read performance with the SeriTek/5PM and a multi-drive RAID 0 configuration.
Most users interested in video editing are looking for high performance. However, if you don't need a high performance RAID, a 2-port card like the SeriTek/2SE2-E will do the job.
http://www.amug.org/amug-web/html/amug/reviews/articles/firmtek/2se2e/
Have fun!

PCIe SATA Cards for RAID for video: Seritek 2ME4-E vs Sonnet Tempo E4P

Hey Folks,
I'm just about to purchase bigger, faster RAID system for my video editing needs. I've already purchased 1TB Barracudas for the drives and I have decided on the Burly dual PM for the enclosure. http://www.burlystorage.com/ccp0-catshow/burlydualpm.html
The questions is which card? I've had a seritek 2 port card and also their expresscard for years without a problem. But some tests I've seen indicate that the Sonnet is a bit faster. Then again, I know that some people had problems with the firmware at least as recently as last spring.
What do people say? Hatter and Japamac, I'm hoping to hear from you.

FirmTek:
If you would like the ability to support port multiplier enclosures and 3rd party SMART applications, the FirmTek SeriTek/e6G would be my choice for a low cost 2-port 6G controller with these features. This card features hot swap and is also able to hot plug Oxford 936/946 based enclosures without the need for a restart. Installation is easy.
I use the SeriTek/e6G in the 2009 Mac Pro with Mac OS X 10.6.5. The PCIe 2.0 slots in the 2009 model provide optimized performance. >
http://www.firmtek.com/seritek/seritek-e6g/
You want a 4x or above card usually, one that has more bandwidth and performance, than those low end 1x 2-port cards that can't drive enough MB/sec to make using multiple drives / multiple enclosures.
Well, seeing you went with Seagate, not my cup of tea, I would have said WD Black Caviar 2TB drives instead.
Sonnet 4-port E4P is what I have used but it or its drivers may be an issue, totally unsure.
PM today is limited by today's drives. When it came out drives were slow by comparison, a mere 75MB/sec while today one drive can shovel 90-125MB/sec or half of what a PM can handle. You only get in real world about 250MB/sec maybe (overhead takes away from that 300MB/sec per port). That means while 6Gb is great, PM enclosures like FirmTek5PM need a new faster PM chip. Again, no idea where that is or when we will see it.
Maybe you should ask about SAS and be looking at even higher end RAID controllers from Areca perhaps.

What is the best e-Sata PCI RAID card for Mavericks.

What is the best e-Sata PCI RAID card for Mavericks. Bought a new MAC PRO with Mavericks and the older PCI 1095,3124 that I used on older MAC Pro does not work. The MAC sees it, but the drivers never show up as being installed. If I could find drivers that work or a recommended PCI card it would be appreciated.
Thanks

PM made sense - 6 yrs ago when disk drives were much slower. Today it is a bottleneck.
SAS makes more sense. Outside of SSD, no disk drive maxes out by itself one PM interface (an SSD will) but it also means just two drives are enough to do so. So check out why to avoid PM:
www.macperformanceguide.com

Suggestions for: external SATA array with a PCIe SATA card??

Seems like this would be a good idea but have no idea what hardware to be considering.
external SATA array with a PCIe SATA card
Thanks
John

Seems like this would be a good idea but have no idea
what hardware to be considering.
external SATA array with a PCIe SATA card
Thanks
John
I purchased and internal raid kit, Rocket Raid 2320 card and Maxupgrades kit. This guy will help you get your equipment running with over the phone with personal customer service. He has external configs also.
http://www.maxupgrades.com/istore/index.cfm?fuseaction=category.display&category _id=313&CFID=3649947&CFTOKEN=58951206
Good Luck
Z1&V1user

I'm looking for a PCI UMTS card for Portege M700

First of all Hi everybody, as above mentioned in the title is about the Portege M700, I'm looking for a PCI UMTS card for this model have here a 8775 Sierra lying around, but this is unfortunately not recognized in Win7, I can times someone may say what card for this laptop is, or even something where I could get so ...???
Thanks apologize in advance

Hi
You need a 3G broadband module?
As far as I know some of the M700 Portege series have been equipped with the 3G module I think its from Novatel but Im not quit sure
However, if you need an part for the Toshiba notebook which would be compatible for sure, then the best place for buying such part is your ASP.
The guys could check what parts are compatible and could order it from Toshiba if this would be really necessary
Greets

[nForce] PCI SATA Card...Will it work?

I'm planning on installing a PCI Sata card to run 2 WD 80Gb drives...My question is, will I run into any problems when trying to install Xp??? I know that the card came with a CD, but will windows recognize the card and load the drivers automatically? Thanks in advance and sorry if this a noob question!

if you look on the CD that comes with the card, there maybe some drivers that you have to copy to a floppy disk, for windows xp
as you startup windows setup, it prompts "Press F6 to install third-party SCSI/RAID controller" (or something like that). then insert this floppy when prompted
maybe if you tell us what SATA card you have / intend to buy, someone can offer better advice...

SATA Card for G4 DA

I've got a PowerMac G4 533 DA and I'd like to put a large hard drive in it for storage. I'd like to know if you have to get a specifically labeled Mac compatible PCI SATA card or will others work (like for PCs). The Sonnet ones are just so expensive compared to essentially the same hardware for PCs. I do not need it to be bootable, this would only be for expanded storage over the tiny IDE drives already in use.
I am running Leopard on it after creating a custom Leopard disk to avoid the clock speed limitation (incase Leopard supports a wider variety of cards than Tiger).

You'd have to weigh up all the factors but you could also just get a large ATA/PATA drive and then get a software solution for the drive size limitations.
SpeedTools ATA Hi-Cap Support Driver: Allows the use of extended capacity ATA drives (drives greater than 128 Gigabytes in size) on older (Pre Mirrored Door) G4 and G3 Macintoshes running MacOS X versions 10.2 and later. http://www.speedtools2.com/ATA6.html
[Overdrive|http://mac.profusehost.net/overdrive/index.html] - free utility to use >128GB drives in old computers. Read warnings about beta releases in general.

Anybody using MOTU PCI 424e card for 2408 with new MacPro Cylinder?

I upgraded my older Mac PRO tower which accepted multiple PCI 424e cards for the new Mac Pro cylinder. I purchased from Magma their Express card cage with Thunderbold output in anticipation. Computer arrived and I removed the card and inserted into the card cage, directed audio to the card but no go. iTunes, for example freezes when the card is selected. My MOTU Digital Performer also does not allow Analog in or out with the card.
I have contacted MOTU, they do not have a solution. Magma, the card cage manufacturer has not come back with a solution. Apple suggested visiting these forums for possible ideas.
My studio is dead in the water until I solve this OR I need to go back to the slower old MacPro.
Thanks in advance.

Did you install the FCS suite onto the new computer by using the original disks?
You should. Don't forget to run all updates, repair permissions and restart.
Or did you migrate the applications from the older Mac? You should not do this.
http://discussions.apple.com/thread.jspa?threadID=2113535

Boot MEGA 180 from PCI Sata card

My onboard IDE controller has given up the ghost so I have purchased a PCI sata card to use a spare sata disk, the problem is I can't see any way to get the 180 to boot from the PCI card. Anyone any ideas?

Yep - I disabled the PATA ports.
No - the card has no bios - I guess this is the problem.

SATA Card for G5 Dual 1.8Ghz

I'm looking for an internal SATA card for my PowerMac G5 Dual 1.8Ghz. I've got a couple hard drives laying around that I wanted to RAID together with my Time Machine Backup drive. Instead of spending hours looking on Google, I figured I'd poll the masses.
Newegg.com has a ton but I want to make sure I get one that is compatible with my hardware.
Thanks in advance!

The only sure thing is the Firmtek Seritek cards.
They are also the only ones that support boot to the connected drives.
Native OS X support is also an important point.
Firmtek also provides excellent tech support
After that, Highpoint has compatibles, and non compatibles.
They don't support boot, and, but can perform well enough.
If you take the path less taken, and get a card that uses generic Silicon Images drivers, then OS X support, and successful use, is highly variable (to say the least).

Are there PCI thunderbolt cards for mac pro 3.1?

are there PCI thunderbolt cards for mac pro 3.1?

DCWinton wrote:
Rick
It's that last sentence I'm curious about. "However a MacPro already has much more capability already built in than Thunderbolt can add."
I'm thinking of getting a Mac Pro, but see that it doesn't seem to have Thunderbolt. I'm not sure if I care. The reason for the Mac Pro is that I'm topping out my 8gb RAM 27" iMac capacity with the volume of work going through it, and my tech tells me I'm pushing it too hard. I use it to run a small law office, but usually have about 15 apps open, with lots going on in the network in the background.
Is there any reason to wait until Apple puts Thunderbolt into the Mac Pro?
Thunderbolt will not increase the performance capability of the MacPro. It will add a bus that can be convenient, especially later on when Thunderbolt devices become more common, more mature and better supported - oh, and with more common will come less costly. From a pure performance standpoint the existing PCIe slots are much more capable and cheaper to implement. You would be giving up nothing with a current MacPro.
My opinion. Thunderbolt is really a great move forward in the long run - needed something to replace Firewire and this is it. But there is no reason to wait on Thunderbolt on MacPro - it is redundant.
Rick

PCI-Express Card for SSD that boots Mac OSX?

I'm thinking about upgrading my 2008 Mac Pro with an SSD boot drive, but I want to get the maximum speed out of the SSD. Since many of the SSDs have a SATA III interface capable of 6Gb/s, I'd also like to get an internal controller that will allow me to boot into Mac OSX. Which card do you reccommend?
Also, is there anyway to place the SSD in the lower optical drive bay of the Mac Pro? If so, what will I need to do that?
Thanks!

The only way to get greater than effective speed on the sata2 connection is to raid the ssd's. Otherwise you are stuck with sata2 speeds.
Here's a thread on sata3 pci cards in these disccussions:
PCIe card to enable bootable SATA3 SSD on early 2008 mac pro?
If you want to do some research in other places there are many hits on this topic when you google "sata3 pci card for mac pro".
Also, I just recently became aware of a new pci card that OWC announced which they call Accelsior™. It's not cheap, even for a 120GB drive.
OWC 120GB Mercury Accelsior™
Here's MacPerformanceGuilds' review of it.
Basically it's a ssd on a pci card thus limited to the pci speed and not the sata speed. Looks cool.

Ok, so now I need a new eSATA PCI Express Card for my Mac Pro

I have a Seagate eSata External Drive which comes with an eSATA PCI card.
The http://www.cwol.com/serial-ata/esata-pci-express-1-ext-1-int.htm site recommends this card: eSATA PCI Express Card - 1 eSATA II and 1 Internal SATA II Port, but it doesn't specify whether it works on a Mac Pro - any suggestions?
Mac Pro Quad Core 2.66 Mac OS X (10.4.6)

Hi
I think the Radeon 9800 is certainly the most powerful graphics card you could buy for your G4 and would do everything you need.
Just be aware there are at least 3 different Mac versions though.
There's a G5 version, the Radeon 9800 Pro Mac Special Edition, which is 8X AGP and has 256MB VRAM.
There's an older Radeon 9800 Pro Mac Edition, which is 2X/4X AGP and has 128MB VRAM.
Finally there's a newer Radeon 9800 Pro Mac Edition, which is 2X/4X AGP and has 256MB VRAM.
So long as you get one of the 2X/4X AGP versions, either with 128MB or 256MB VRAM, it should work fine.
It's perhaps also worthwhile mentioning they do require a separate internal power connection, although this can be taken from a hard drive molex power connector. Also they have a cooling fan which can be noisy.
I hope this helps.

Which PCI SATA card for B&W G3?

Similar Messages

Maybe you are looking for