Which ports do I open so QT Broadcast is seen from outside a local network?

I need some help with proper port settings using QT Broadcaster Version 1.5 (113) from mac to mac (running X.4.5 on all systems). I am able to send a Live QT Broadcast to my local network no problem but the broadcast is not seen from outside of my own local Network.
I’m assuming I must first address port settings on my cable modem and / or a Belkin gateway 4 port router.
The Broadcast works fine on all 4 of my macs connected via ethernet to a Belkin 4 port router which in turn is connected to a Toshiba PCX2500 cable modem.
I’m guessing the Toshiba modem is the problem and not the Belkin router. I say this because when I remove the router completely my Broadcast is still not seen by anyone from the outside. This leads me to believe that the cable modem may be the culprit. But then again I’m at a loss to know which ports to open up so others on the internet can also view my broadcast. Please note I do not wish to broadcast to more than one person at a time. Hence no need for QTSS or DSS.
To the best of my knowledge QT Broadcaster in itself should suffice from one mac to another w/o the need for a server. Is this correct? If not, I do have Darwin loaded to another separate mac system in the event I must first use it to reflect this braodcast.
Any help would be sincerely appreciated & please pardon my second post on the same subject / QT Broadcaster which I have slighly reworded in hope of getting some help.
SDMacuser

ok .... i just pinged www.gamesspy.com and i set it at 30 instead of the default 10 and here are my results:
Ping has started ...
PING www.gamespy.com (216.35.19.179): 56 data bytes
64 bytes from 216.35.19.179: icmp_seq=0 ttl=241 time=34.822 ms
64 bytes from 216.35.19.179: icmp_seq=1 ttl=241 time=41.560 ms
64 bytes from 216.35.19.179: icmp_seq=2 ttl=241 time=35.346 ms
64 bytes from 216.35.19.179: icmp_seq=3 ttl=241 time=29.110 ms
64 bytes from 216.35.19.179: icmp_seq=4 ttl=241 time=32.620 ms
64 bytes from 216.35.19.179: icmp_seq=5 ttl=241 time=30.933 ms
64 bytes from 216.35.19.179: icmp_seq=6 ttl=241 time=28.824 ms
64 bytes from 216.35.19.179: icmp_seq=7 ttl=241 time=28.016 ms
64 bytes from 216.35.19.179: icmp_seq=8 ttl=241 time=28.968 ms
64 bytes from 216.35.19.179: icmp_seq=9 ttl=241 time=36.142 ms
64 bytes from 216.35.19.179: icmp_seq=10 ttl=241 time=26.944 ms
64 bytes from 216.35.19.179: icmp_seq=11 ttl=241 time=28.078 ms
64 bytes from 216.35.19.179: icmp_seq=12 ttl=241 time=27.286 ms
64 bytes from 216.35.19.179: icmp_seq=13 ttl=241 time=25.052 ms
64 bytes from 216.35.19.179: icmp_seq=14 ttl=241 time=25.918 ms
64 bytes from 216.35.19.179: icmp_seq=15 ttl=241 time=32.702 ms
64 bytes from 216.35.19.179: icmp_seq=16 ttl=241 time=37.229 ms
64 bytes from 216.35.19.179: icmp_seq=17 ttl=241 time=35.537 ms
64 bytes from 216.35.19.179: icmp_seq=18 ttl=241 time=29.943 ms
64 bytes from 216.35.19.179: icmp_seq=19 ttl=241 time=31.380 ms
64 bytes from 216.35.19.179: icmp_seq=20 ttl=241 time=26.326 ms
64 bytes from 216.35.19.179: icmp_seq=21 ttl=241 time=25.403 ms
64 bytes from 216.35.19.179: icmp_seq=22 ttl=241 time=26.719 ms
64 bytes from 216.35.19.179: icmp_seq=23 ttl=241 time=29.488 ms
64 bytes from 216.35.19.179: icmp_seq=24 ttl=241 time=29.223 ms
64 bytes from 216.35.19.179: icmp_seq=25 ttl=241 time=35.644 ms
64 bytes from 216.35.19.179: icmp_seq=26 ttl=241 time=33.442 ms
64 bytes from 216.35.19.179: icmp_seq=27 ttl=241 time=29.424 ms
64 bytes from 216.35.19.179: icmp_seq=28 ttl=241 time=30.499 ms
64 bytes from 216.35.19.179: icmp_seq=29 ttl=241 time=25.632 ms
--- www.gamespy.com ping statistics ---
30 packets transmitted, 30 packets received, 0% packet loss
round-trip min/avg/max/stddev = 25.052/30.607/41.560/4.043 ms

Similar Messages

Oracle R12 which port to be open

Hi,
I will install Oracle R12 , But Security team asking what are the port need to be open for Implementation Purpose.
Regds
Murali

Refer to the database/application context files, all used ports are listed there.

How to be sure port 10443 is open on vintage airport extreme ( ufo shape, not square)

My Denon 2112 AV reciever is having intermittent internet connect issues. Denon says to be sure port 10443 in my router is open. How do I check this and see if it is open on my vintage (ufo/dome shape) airport extreme?

To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <skip this setting as you will be custom configuring which ports you need opened for the TiVo>
o Public UDP Port(s): <enter the appropriate UDP port values>
o Public TCP Port(s): <enter the appropriate TCP port values>
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
o Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
o Click "Continue"

On which interface should i open ports?

Hi!
Got a case from a customer. They want me to open some ports so that one client can use some applications.
The problem is, I am not sure on which interface i should open the ports. The customer have about 10 interfaces on the ASA. It's a client on the inside network and it should be able to talk to internet through the ports, and anyone on the internet should be able to reach the client on the same ports.
The client uses a static IP.
Sent from Cisco Technical Support iPad App

Hi,
You need to map the flow of traffic for your customer. That way you can plan the changes without breaking anything.
It could be as simple as creating ACL's for the inside and outside interfaces + nat or something more complex.

Which ports need to be open for messages and facetime to work properly?

I noticed that Messages no longer works since upgrading to Yosemite on my work network. But it did when i was in Mavericks. Did they change something in Messages in the upgrade that would cause it to no longer work? ports?
I'm behind my work firewall, which ports need to be open for messages to work properly?

Just make sure your 9001 port is open.
Hope this works..
Hamid

Which port is open for connection ?

how could I know which port is open for connection ?
In the java, I use JDBC to connect to Oracle,
connection = DriverManager.getConnection("jdbc:oracle:thin:@localhost:1521:sid", "scott","tiger");Do we have a command to show open port ?
Thanks.

What is your Oracle version, and do you use dedicated connections or "shared servers"? From your port number invoked (1521), I'll guess you use dedicated connections. In that case, the listener (located at 1521) will "spawn" a dedicated process for your session, and tell this process to start on another port (usually falling on a certain range, depending on your OS). An easy way to see this would probably to turn listener tracing on. Here's what I found in the log file after I started a new (dedicated) session on my 10.2 DB:
"22-OCT-2006 21:31:16 * (CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=ora102)(CLIENT_REGISTRATION=ora102)(CID=(PROGRAM=C:\oracle92\bin\sqlplusw.exe)(HOST=DANIELROYLAPTOP)(USER=Daniel))(CLIENT_REGISTRATION=ora102)) * (ADDRESS=(PROTOCOL=tcp)(HOST=192.168.1.100)(PORT=3198)) * establish * ora102 * 0"
HTH
Daniel

Which port need open for Imoprt WS in to the TREE ??

ZfD6.5SP2.
WS----firewall-------NW_SERVER
Which ports ned open on the firewall for import Ws in to the TREE ??
Serg

Serg,
>Which ports ned open on the firewall for import Ws in to the TREE ??
8039
Jared Jennings
Data Technique, Inc.
Novell Support Forums Sysop
http://wiki.novell.com

Which ports to open on FW for Voip

Hello,
Can anyone tell me which ports (TCP and UPD) to open on the firewall when you have ip phones and ip communicator behind it?
This just to squeeze down the range a bit.
Thanks for your help.
Kurt

Kurt,
Take a look at the following link.
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/sec_vir/udp_tcp/index.htm
Hope this helps. If so, please rate the post.
Brandon

Which ports to open in PIX for outgoing Cisco VPN client connections ?

I have Cisco vpn clients behind the PIX and i want them to connect to a vpn 3005 which i behind another PIX . Can anybody tell me which ports i have to open on both the PIX firewalls ?

It depends on how you have deployed your VPN Remote Access users.
By default, if you enable IPSec-Over-TCP or IPSec-over-UDP, then port 10000 is used for both, these methods are Cisco Proprietary and can be changed.
If you use NAT-T (NAT Traversal), the Standards-based implementation, then it uses UDP-4500).
either way, the operation of the VPN depends on:
1) Whether these service have been enable on the VPN Concentrator
2) Enabling the relevant transport settings on the VPN Client connection Properties.
Regarding the PIX infront of the VPNC3005, you will need to allow these above ports inbound to your VPNC3005 Public interface.
Locally, it depends if you filter outbound connections through your PIX. If you don't, then the PIX will allow the connection for the VPN Client attempting to access the remote VPNC3005

Which ports to open on winxp when filesharing?

When I tries to connect a winxp shared folder from a mac it does not work if the firewall on xp is on, when I turn it off everythings works ok. Which ports do I need to open?
/Ulf

What I would suggest is that you install Little Snitch on your mac. Little Snitch is an application aware firewall that controls your outgoing connections.
By default little snitch allows out any network connections on your local network, so if you remove that rule it will alert you when you try and connect to your windows sharepoint, it will also tell you which port it is trying to connect to.
You may then see the complete ports you need to open your windows firewall.
The other thing you could do is give your computers static ip addresses on your network then setup a firewall rule on your windows box to allow all connections from your mac's ip address.

Which ports need to be opened?

I am about to install the SAP Web Application Server Java 6.40 SR1 on Solaris in a highly secure emvironment.
I need to open all the necessary ports in the firewall in advance of the installation. Which ports do I need (as a minumum) to run the portal with KM, Collaboration and trex?
And where do I configure the settings for the P4 protocol? How do I make it run on SSL?

You can pick and choose:
SAP Ports
Scheme               - Example (05) - Port Description
32 + <SYSNO>         -         3205 - ABAP Dispatcher
33 + <SYSNO>         -         3305 - ABAP Gateway
36 + <SYSNO>         -         3605 - ABAP Message
47 + <SYSNO>         -         4705 - ABAP Dispatcher Security
48 + <SYSNO>         -         4805 - ABAP Gateway Security
8 + <SYSNO> + 0     -         8050 - ABAP ITS HTTP
8 + <SYSNO> + 1     -         8051 - ABAP ITS HTTPS
81 + <SYSNO>         -         8105 - ABAP ITS Message Server
5 + <SYSNO> + 00    -        50500 - Java Dispatcher HTTP
5 + <SYSNO> + 01    -        50501 - Java Dispatcher HTTPS
5 + <SYSNO> + 02    -        50502 - Java IIOP
5 + <SYSNO> + 03    -        50503 - Java IIOP Initial Context
5 + <SYSNO> + 04    -        50504 - Java Visual Admin P4
5 + <SYSNO> + 05    -        50505 - Java Visual Admin P4 over HTTP
5 + <SYSNO> + 06    -        50506 - Java Visual Admin P4 over SSL
5 + <SYSNO> + 08    -        50508 - Java Telnet
5 + <SYSNO> + 10    -        50510 - Java JMS
5 + <SYSNO> + 18    -        50518 - Java SDM
5 + <SYSNO> + 20    -        50504 - Java Server Join
5 + <SYSNO> + 21    -        50504 - Java Sever Debug
5 + <SYSNO> + X + 5 -        50525 - Java Server Cluster Element (X=1-9)

Netconnection.connect(), which port to open

Hi all,
I have a swf running within a web browser and publishing audio stream to the server. If the client's computer has a firewall, should it be configured for outgoing netconnection.connect() request?
Thanks in advance
-s

Generally firewalls at clients end do not block outgoing connections but its not that they cannot be configured to do so. You can check if client's machine firewall blocks any outgoing connections and what all connections and on which port. If you find its blocking rtmp connections or blocking port 1935 and 80, you might want to open them.

I want to be able to totally block the FaceTime functionality in my home network. I would like to do this at the router level. Does anyone know the hostname or IP address that the FaceTime application uses? Or which port it connects to?

I want to be able to totally block the FaceTime functionality in my home network so my 4 kids aren't using the Facetime feature- It was easy for Skype just had to enter the work Skype on my Router Security list- and it denies access. I would like to do this at the router level for FaceTime? Only site I find in init.ess.apple.com - is this the startup site for Facetime? Does anyone know a site I can block, hostname or IP address that the FaceTime application uses? Or which port it connects to?

I would presume so, but it might be worth your while to experiment and play around with different combinations to see if you can block FaceTime while keeping Game Center open. Good luck!

FTPEx: 425 Possible PASV port theft, cannot open data connection..

Hi All,
I am getting the below the error while comminicating to FTP server.
Delivery of the message to the application using connection File_http://sap.com/xi/XI/System failed, due to: com.sap.aii.af.ra.ms.api.RecoverableException: Possible PASV port theft, cannot open data connection.: com.sap.aii.adapter.file.ftp.FTPEx: 425 Possible PASV port theft, cannot open data connection..
This error is random. Some times service is working is fine and some times its failed to process.
Can any one suggest me the peramnent solution for this.
Thanks & regards,
Kartikeya

Hi
The reason for the error is
The ip address (+port) is not same for both these operations
    - Control connection
    - Data Connection
Changing active/passive mode settings might help (as a common solution).
Problem can occur due to below settings,
   - FTP server/ Firewall on its side (affects Passive Mode)
   - FTP client/ Firewall on its side (affects Active Mode)
After Initial Control connection is made, the below happens for Data connection
When Active, the CLIENT opens a dynamic port for DC on which it would be listening, for the server to bind its source port
When Passive, the SERVER opens a dynamic port for DC on which it would be listening for the client to bind its source port
when the firewall on Server side does not have these ports open, you get the above error.
The error could be because of other reasons also, but I suspect that the dynamic port is out range of the ports opened at your FTP server firewall.
So now I think you are one step forward to fix the issue
Regards
Vishnu

Our IT Director will not allow the appropriate TCP and UDP ports to be opened on the district WAN

I have about 30 Apple TV Units and our IT Director will not allow the appropriate TCP and UDP ports to be opened on the district WAN. When our teachers try to log on to Apple TV to broadcast lessons, websites, etc., they are booted off the network after about 20 minutes.
Any ideas for how I might solve this without having to hard-wire the Apple TV Units?

Honestly, you do not.
Either the IT director will cave and allow the appropriate ports or it doesn't work.
Hard wiring the ATVs will not rectify the problem.

Which ports do I open so QT Broadcast is seen from outside a local network?

Similar Messages

Maybe you are looking for