While loop inside a event structure

Dear
I have no much concepts on event structure.
Let's assume there is a dialog box with Okay and Cancel button.
I put the event structure for Okay and Cancel button.
In Okay event, there is a while loop for detecting some data continuously.
In this case, I want to use Cancel button to stop the while loop during the detection.
How can I do to receive signal from the Cancel button?
Thank you in advance.

I'm not sure that the event structure should be used to handle that situation : while the OK event is executing, either the Front panel is locked and new occuring event will be stored until the OK event is completed (so the Cancel button action will not be detected !) or the Front panel is unlocked (see below *) and the Cancel button action will stop the loop, but the Cancel button event case will not be executed, since the event has already been processed in the OK case !
You should probably use a single button to run/stop the loop, as shown in the attachment
* While editing the event case, unmark the "Lock front panel for this event complete" at the bottom. But of course, the code in the cancel case will not run, since the event occuredMessage Edité par chilly charly le 03-31-2007 05:27 PM
Chilly Charly (aka CC)
E-List Master - Kudos glutton - Press the yellow button on the left...
Attachments:
Event button.vi ‏11 KB

Similar Messages

Event controll: How to stop a running while loop inside a event structure

Hello,
I have some problems with controlling a while loop inside a event structure (see attached VI).
I habe 3 buttons ("Start Measurement, Stop Measurement, Quit Program"). When a measurement is running, it should be possible to stop the measurement by clicking on "Stop Measurement", but this does not work.
Has anyone an idea?
Thanks a lot and best regards,
Michael
Message Edited by MichaGue_01 on 04-23-2010 04:37 AM
Solved!
Go to Solution.
Attachments:
Event_Controll.vi ‏27 KB

Hello,
Try not to use while loops inside a Event structure.
My approach is using two While loops (one will have only the Event structure).
I had to use to Flag buttons that make it a bit more complicated but i am sure somebody will come up with a better idea, or you might want to have a think about it yourself.
Have a look on the modified version on the attachment.
Once you are happy how it works then you can Hide the 2 flag buttons from the Front Pannel by going to Block diagram right-click the indicators and choose option "Hide Indicators/Controls"
I did it in LV 8.6 so i hope you can open it on your PC if not i can downgrade it.
If you have any problem let us know.
Regards
Dimitrios
Test Systems Computing Engineer
Cummins Turbo-Technologies
Attachments:
Event_Controll[1]_modified.vi ‏18 KB

How to exit from the DO-while loop in the event structure

Hi all
I am just a beginner for Labview
I want to build a loop in the event structure, but when I enter in the loop, it seems the system is dead, and I can't exit the loop.
here I attached a simple sample.
In the sample. when I press the start_calculation button , the calculation start, but the system is dead, and I can't exit calculation loop.
actually, i just want switch the different operation by changing the event action.
anybody has a good idea about it??
thanks so lot
Attachments:
event_problem.vi ‏17 KB

Your problem is that you are trapped inside an event case. It is not a good idea to run extended code inside event cases, else the event structure cannot service other events.
Why don't you use the outer loop for everything? Now things don't step on each others toes. What good is an event structure if it cannot react at all times???
Message Edited by altenbach on 07-25-2008 12:26 AM
LabVIEW Champion . Do more with less code and in less time .
Attachments:
event_problemMOD.vi ‏17 KB

Exit a while loop inside an event case

Hi All, I have a multi-page program. One of it is used to read some analog signal via a USB block continuously.
What I want is when clicking this page, this while loop is activated. Then we can monitor the data. When we click other pages or "Stop" button, this while loop will be terminated. And we can use the other pages to do something else.
Right now I got difficuties in stop the while loop. I do not want to stop the running of the whole program, just want to jump out of this while loop then do other operation.
Could anyone give me some advise how to do it? Thank you very much!

Hi RavensFan, thank you for your reply.Actually this is not my real code because the original one is very very compliacted.
In real code, the tab control you see in inside the bigger while loop, that loop makes the whole program work.
And as what I pointed, the purpose is when I click this tab (if we do not want it to trigger, we can place another "START" button to trigger), an internal while loop inside begins to run. This while loop keeps showing the real time analog signal.
And if I do not want to use this "real time monitoring" function, I want to click somewhere (or doing anything else that can work) to jump out of this internal while loop and keep on using some other functions of the program.
Could you advise about that? Thank you very much!

Simple example - Break FOR loop inside an event structure based on Front panel event change.

I am running a for loop inside a state machine architecture that contains a FOR loop. How can I break this For loop based on Event change in front panel ??
Abhilash S Nair
Research Assistant @ Photonic Devices and Systems lab
[ LabView professional Development System - Version 11.0 - 32-bit ]
LabView Gear:
1. NI PXI-7951R & NI 5761
2. The Imaging Source USB 3.0 monochrome camera with trigger : DMK 23UM021
OPERATING SYSTEM - [ MS windows 7 Home Premium 64-bit SP-1 ]
CPU - [Intel Core i7-2600 CPU @ 3.40Ghz ]
MEMORY - [ 16.0 GB RAM ]
GPU - [ NVIDIA GeForce GT 530 ]
Attachments:
Case inside Event 3.vi ‏19 KB
Case inside Event.ctl ‏6 KB
Case inside Event 2.ctl ‏6 KB

Okay. Accpeting that the design is not favorable and not advantageous when my program expands. I have begin to follow producer/consumer programming architecture.
Please find the attached program which is a simple producer consumer with event structure. I wonder how could I stop looping around the producer and consumer loops over and over again. I am pretty sure that this ENQUEUE ELEMENT loops back to the consumer loop and starts from begining.
I hope my first program in PC architecture with State machine and Event structure is correct.
Abhilash S Nair
Research Assistant @ Photonic Devices and Systems lab
[ LabView professional Development System - Version 11.0 - 32-bit ]
LabView Gear:
1. NI PXI-7951R & NI 5761
2. The Imaging Source USB 3.0 monochrome camera with trigger : DMK 23UM021
OPERATING SYSTEM - [ MS windows 7 Home Premium 64-bit SP-1 ]
CPU - [Intel Core i7-2600 CPU @ 3.40Ghz ]
MEMORY - [ 16.0 GB RAM ]
GPU - [ NVIDIA GeForce GT 530 ]
Attachments:
Case inside Event 3.3-ProducerConsumer Event.vi ‏25 KB
Case inside Event.ctl ‏6 KB

Stop execution of a loop in an event structure

I tried searching the forums to avoid posting a duplicate, but most I could not open most of the vi's as they were higher version.
I put in a dummy while loop in an event structire i intend to use. Once I start executing the while loop, I am not able to stop it using a control for some reason from the fornt panel control.
I am not able to change the vale of the Stop control at all. I tried creating a seperate event for STOP, and I still could not stop the program when the While loop was executing.
I imagine I am missing something really small. I would appreciate your feedback on this.
Thanks,
Nevil
Solved!
Go to Solution.
Attachments:
FrontPanel.vi ‏34 KB

Right click on the event structure and choose "Edit Events" for the case that is giving you trouble.
Be sure the checkbox to lock the front panel is unchecked.
I suspect yours is checked, so your front panel is locked out until the event completes, thus you can never stop your loop.

While loop inside a timed loop

Hi everybody!
   I'm using:
       - LV 7.1 + RealTime;
       - compactFieldpoint;
   I've noticed a strange behaviour, when I put a while loop inside a timed loop. Let's fix timed loop with these settings:
       - 1 KHz clock
       - 1 ms period (yes, I know it's short....)
       - offset 0 ms
       - Phase 0
       - Discard missed period (ON) and MAintain original Phase (ON);
       - Timeout: -1.
   If inside this loo, I put a traditional while loop, waiting (say) for an event to occur, and if this event does not arrive, my cFP-2020 hangs! I mean, it becomes unreachable for the debugger, and, more, if I run a ping to it's address, after some cycles it becomes unreachable also from ping!
   Clearly, this code statement lock the fieldPoint, because if I remove the inner while loop all works.
I know that with 1 ms period, timed loop always finishes late, but I set to discard missed period and timeout to -1.
   It seems to me that sometimes Timed Loop add heavi overhead to programs, I'm turning to all while loop based tasks, even if my application has to be real-time!
   Advices welcomed! Have a nice day!
graziano
Solved!
Go to Solution.

I think the issue here is that putting your while loop inside a Timed Loop increases the priority for that task. Timed Loops can have dynamic priorities set over eachother, but they all run between Above Normal and Time Critical priority. My guess is that the debugger and built-in TCP functions run at Above Normal priority or less. This means your cFP isn't hanging, it's doing what it thinks is best. It's trying to finish this task before handling any lower-priority tasks.
The suggestion to put a Wait function in your loop is an OK one. Keep in mind that you can actually set your wait time to zero instead of one and get the same positive benefit of handling other tasks. I would also suggest that you might look into waiting for this event in a lower priority (non-Timed) loop, and then transmit the appropriate data to your Timed Loop using an RT-FIFO or something. That might give you better handling. Just a thought....
Jarrod S.
National Instruments

Can't we use while loop inside a fn

i am using a while loop inside a fn
it is showing error
the code is
while (a=1) loop
some condition
end loop;
the error is
PLS-00103: Encountered the symbol "WHILE" when expecting one of
the following:
* & = - + < / > at in is mod not rem then <an exponent (**)>
<> or != or ~= >= <= <> and or like between overlaps || year
DAY_
The symbol "*" was substituted for "WHILE" to continue.
PLS-00103: Encountered the symbol "LOOP" when expecting one of
the following:
. ( * % & = - + < / > at in is mod not rem then
<an exponent (**)> <> or != or ~= >= <= <> and or like
between ||
what is the error

It looks like the OP misskeyed the assignment operator and got compilations errors, and from that assumed that you can't use WHILE loops in functions on a Tuesday.
Message was edited by:
William Robertson
I was thinking of his is it possible to increment a value in a function, though I suspect the problem is similar.

How should I set up my VI so that I can use the linear fit coefficient data analysis program, when my values are coming from while loops within a sequence structure?

I'm attempting to create a calibration program, using the printer port, and a Vernier Serial Box by modifying a calibration program designed for the serial box.
There are six calibration points, and to collect them, I have it controlled by while loops so that the numbers are taken when a button is pushed, and this is inside a sequence structure so that I can get the six different points. I feed these numbers into two different arrays (for x and y values) and then try to use the linear coefficient analysis on these points, but the values for the slope and intercepts it returns are not correc
t.
If I cut out the array and coefficient analysis, and feed the same numbers in directly without the while loop and sequence structures, it produces the proper values... I don't know why the numbers it is producing are different, and I'd really like to know.
Thanks,
Karinne.

I would use a data manager sub-vi that would be called by each from of the sequence structure that produced a data point. The data manager sub-vi could auto append new items or could place items in a specific entry of an array. Later on when you want to calculate the linear fit, call the sub-vi to return the array of values.
Stu

Ending a while loop inside a while loop

How do I make a while loop run as long as the while loop that contains it is running? I tried wiring both conditional terminals to a stop button in the outer loop, but that doesnt seem to work? Is there another way?
Thanks.

Hi Jasonalan,
I am not sure what you are trying to implement, but it is true that the loops are not terminating because of data dependency. The stop button in the outer loop will not be read until the inner loop terminates.
If you wish to terminate the two nested loops using a single stop button, you should read the stop button inside the inner loop and wire it to the conditional terminals in both the inner and outer loop. Again, there is no point in doing this unless you have some other logic along with the stop button to stop the loops. If only the stop button is being used to stop both the inner and outer loops, the outer loop will only execute once. In that case, you can just use a sequence structure followed by a single while loop.

Calling a VI in a subpanel with parameters inside an event structure and using an abort button

Hi all,
I have a control panel with a tab control and two tabs have a sub panel in them. At runtime I load the VIs I want in to the sub panels. In the control panel event structure I want to start each of the VIs and monitor the execution state so I can abort the VI while it is running. One method I use can run the VI and the abort event will work (see example). The second method I use does not and this is what I want to do! I have many inputs to the VI I want to pass so placing the VI in the event blocks everything else and it has to wait until the VI has completed, so I cannot monitor the execution state.
I have attached an example of what I want to do.
Any help appreciated.
Martin
Solved!
Go to Solution.
Attachments:
SubPanel.lvlib ‏2 KB

Hello,
You can do this with queues.
The main vi and subpanel vi's should be based on the producer/consumer (events) and you handle the front panel events accordingly in the respective vi's.
Name the queues in obtain queue , for example the Main being MainQ, subpanels SubPanel1Q, SubPanel2Q. When you start the application, initialise the main vi and also run both of the subpanels (just to make sure that the queues are first obtained by themselves). Then you can use obtain queues to do inter vi communication.
For example if you need to send data from main to subpanel1, use obtain queue and use the name SubPanel1Q, pass the required data & command and voila. Subpanel1 vi will receive your message. You can do this anyway you want. Hope this helps.
Beginner? Try LabVIEW Basics
Sharing bits of code? Try Snippets or LAVA Code Capture Tool
Have you tried Quick Drop?, Visit QD Community.

Stopping a while loop inside a while loop

Hello,
I have a while loop which is inside a while loop which houses my enetire application, When stopping the inner while loop portions of my outer loop stop working, How do I setup the inner while stop that it will not interfeer with the outer while loop?
Thanks,
Gil,

It sounds like he is using a simple archetecture. But switching to a different archetecture may not be necessary. Simply because it doesn't work, doesn't mean scrap the whole thing and start over. He's got a bug and needs to fix it. Is it the best archetecture to use, absolutely not, but simple or general archetectures can be effective based on the application.
Post your VI so we can take a look and give you some pointers and suggestions for improvement.
Reese, (former CLAD, future CLD)
Some people call me the Space Cowboy!
Some call me the gangster of love.
Some people call me MoReese!
...I'm right here baby, right here, right here, right here at home

'While Loop' inside a 'Repeater' executes only once

Hi,
I am using a 'While Loop' action inside a 'Repeater'. The while loop executes only for Repeater.CurrentItem = 1 and not for the subsequent items. Any clue?
Regards,
V M.

And the 'While_Loop.Break' = "false". Thaks for the tip.
Regards,
V M.

My First while loop inside PL/SQL block not working , please help

Hi ,
I am new to PL/sql and struck at PL SQL blocks , please help to solve this .
declare
v_A number constant :=10 ;
j number constant := 3 ;
BEGIN
WHILE j < v_A
LOOP
DBMS_OUTPUT.PUT_LINE('Hai');
END LOOP;
END;
please help as how to resolve this .
Thanks in advance .

btw it's a useful habit to use indentation to highlight the block structure. Also it's worth deciding what your convention will be for keywords (I use uppercase, lowercase is also fine as far as I'm concerned but I've set up my editor to uppercase them) and variables, database object names etc (I use lowercase), e.g:
DECLARE
   v_a CONSTANT PLS_INTEGER := 10;
   j   CONSTANT PLS_INTEGER := 3;
   i PLS_INTEGER := j;
BEGIN
   WHILE i <= v_a LOOP
      DBMS_OUTPUT.PUT_LINE(i);
      i := i +1;
   END LOOP;
END;or perhapsdeclare
   v_a constant pls_integer := 10;
   j   constant pls_integer := 3;
   i pls_integer := j;
begin
   while i <= v_a loop
      dbms_output.put_line(i);
      i := i +1;
   end loop;
end;When I see "declare" and "BEGIN" in the same block of code I worry about the standard of code I'm going to see...

Quit from while loop inside a vi that run a while loop

Hello,
this is just an example
i have a led that blink inside a subvi and i what to stop it form the ui of the user (MainHelp.vi)
but because the subvihelp.vi dont know the stop button it will not stop when i klick on the stop button
How i can work it out with out using global Var
thanks for your replay.
Attachments:
MainHelp.vi ‏9 KB
SubVIHelp.vi ‏9 KB

Hi
Here is one method to stop a blinking VI in a SubVI. I tried not to change your version of how the blinking works. Since the subVI is running continuously this example calls the VI using static reference and using the control names. You could also use a queue to pass values to the subVI controls.
Your original VI has a lot of stuff that made no sense, so I cleaned them all out or up, so to speak.
Good Luck.
Mark Ramsdale
Attachments:
MainHelp.vi ‏12 KB
SubVIHelp.vi ‏9 KB

While loop inside a event structure

Similar Messages

Maybe you are looking for