White horizontal lines across the bottom of Macbook display

Shortly after I turned on my Macbook last night, the bottom of the screen started to flicker and solid white lines appeared across the bottom of my screen. They go up roughly a couple inches from the bottom, and fade towards the right of the display.
When I restart my computer, They reappear as macosx is loading.
When I mouse over these white lines, the cursor is unaffected, yet they dont appear when I screenshot.
I've gone back through all the discussions but couldnt find any solutions =S
Ideas?

I think you may find hope with this article:
http://docs.info.apple.com/article.html?artnum=303319
The effect is rare but not unknown. Unless it's a hardware issue, you might be able to use this fix.

Similar Messages

  • When doing the app exposé gesture, is it normal to see a thin white horizontal line at the bottom of the screen after minimizing a window?

    I noticed that when I open two windoes (say Safari and Trash can) and minimize both windows so they go on the dock, when I do the swip down gesture with 3 fingers (App Expose´) there is a thin white horizontal line at the bottom of the screen. Does it happen to every macbook pro out there?  Is this normal?  Hope it's not a display screen problem...

    You would have to have multiple pages of the app minimized.
    This is what it looks like with Safari with 1 page open and 4 minimized.

  • I have a horizontal line across the bottom of my screen how do I remove it?

    Re: Macbook Air mid 2011, I have a horizontal line across the bottom of my screen, it appeared when I was updating my iPhone, How can I remove this line from my display?

    It may be a GPU or display issue. In both cases, make a backup of your Mac and take it to an Apple Store or reseller to get it repaired.
    To check whether it is a GPU or display issue, try taking a screenshot by pressing Command, Shift and 3 keys. The screenshot will appear in the Desktop, so open it and check if the line appears in the screenshot too. If so, it is a GPU issue; if not, it is a display issue.

  • Horizontal line across the monitor. It happened yesterday.

    I have a HP ENVY 23-c1 10xt AiO (Lavaca3-SB)PCUS and there is a horizontal line across the monitor.  It happened yesterday.

    Hello again javajohn23,
    I would like you to try the following steps:
    Step 1. Turn off the computer, and then remove the power cord
    Step 2. With the power cord disconnected, press and hold the power button for five seconds
    Step 3. Reconnect the power cord, and then turn on the computer
    If the above steps do not resolve it try the next set up steps:
    Step 1. Restart your computer
    Step 2. Repeatedly press the F10 key about once every second for five seconds after turning the computer on
    Step 3. Wait five seconds
    Step 4. Press the F5 key. This restores the default settings of the BIOS
    Step 5. Press the Enter key. This accepts the changes
    Step 6. Press the F10 key. This opens the Save and Exit window
    Step 7. Press the Enter key. This saves the changes, exits the BIOS, and then the computer restarts
    Step 8. Restart the computer.
    Another thing I can think to try is review the HP Support document: Changing Display Settings, Background Image, Icons, and Screen Saver (Windows 7) to see if you can identify anything out of place.
    We can also try to reload the Intel Graphics Driver for your computer as it will wipe out the settings when the new driver  is reinstalled.
    Please re-post with the results of these steps. Thank you for posting on the HP Forums. Have a great day!
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

  • Why do i have a grey thick horizontal line on the bottom of my screen imac

    hello
         I been having a problem with my iMac 21.5 inch mid 2011 since this monday January 7,2014. Theres a grey and some times black thick horizontal line at the bottom of the screen, I cant see my programs at the bottom of the screen. First its black then turns into grey and it starts flickering and then it stops flickering and it wont go unless I turn off my mac or put it to sleep, and then like an hour it comes back again. please could you help me Thank you.

    Hello Armando
    Check out the article below for troubleshooting your issue with the display. There are a few things that can be done, like changing the resolution of the display and also to reset the NVRAM to see if that resolves that for you.
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/ht1573
    Regards,
    -Norm G.

  • HT201177 I have a horizontal line in the bottom 1/3 of my screen display that I can't get rid of

    I can't seem to get rid of this black horizontal line in the bottom 1/3 of my display its there in all applications and there appears to be a shadow bar behind it? any help would be appreciated

    What model iMac? This forum covers three different variants made before 2006. They have different display technologies.
    Doing "About this Mac" from your Apple menu and posting the info found there for your processor type is a good start. If that shows you have an Intel processor, those iMacs are different enough to have a separate forum here:
    iMac (Intel)

  • Pictures taken with my 1D Mark IV show a blue horizontal line at the bottom from ISO 400 onwards.

    Pictures taken with my 1D Mark IV show a blue horizontal line at the bottom from ISO 400 onwards. So far nobody has been able tot tell me the cause of this problem. The body is still quite new (15000 pics taken).

    I agree that it looks like a column of photosites is not working.  But... I'm curious as to why this would only happen at ISO 400 or above. 
    The sensor is covered with photosites -- they are monochrome.   On top of the photosites is the "bayer mask".  The mask is a checkboard pattern of red, green, and blue "lenses" which makes the photosite beneath only sensitive to that particular color.  They are group in clusters of 4 photosites in a 2x2 matrix.  Two of the four squares (in opposing corners) are green.  One corner is red.  One corner is blue.  If you were to lose a column which happens to be along the red/green column (as opposed to the green/blue) then you'd lose red sensitive and half the green sensitivity in that column.  The result would be that this column is flanked by two "working" columns which are full of green/blue photosites... hence the teal blue look.
    I do not know if this will work for you, but oddly... you can actually sometimes "clear" stuck pixels (but usually this is an indvidiual stuck pixel... not a whole column of them) by putting the camera into manual sensor cleaning mode (and you may have to do this 2 or three times).  While the normal point of the self-cleaning mode is to flip up the reflex mirror and open the shutter so that you can inspect and clean the sensor (really the front-most filter because you can't actually touch the real sensor), it also neutralizes the charge on the sensor (or so I've read).  This charging and discharging of the sensor a few times can often get "stuck" pixels to start working again.  BUT AGAIN... I've only ever seen this used on individual stuck pixels... never a whole row.
    Tim Campbell
    5D II, 5D III, 60Da

  • I have a horizontal line across the middle of the ipod screen and the ipod and itunes won't sync.  What is the line and is it connected to the no sync.

    I have a horizontal line across the middle of the ipod screen and itunes and the ipod won't sync.  What is the horizontal line and is it connected to the no sync.

    Hey Dean Marvin,
    Thanks for the question. These two symptoms are probablyh related. To troubleshoot, let's try resetting your iPod:
    How to reset iPod
    http://support.apple.com/kb/HT1320
    Thanks,
    Matt M.

  • My T400 has a flickering horizontal line at the bottom of the screen.

    A horizontal, flickering band has appeared along the bottom edge of the screen. When it settles down, there is just a thin line across the taskbar icons. Kindly assist to remove it.

    Hi Mtshali,
    Here is some info regarding your issue:
    http://answers.yahoo.com/question/index?qid=20110725163248AAEzk8r
    How long have you had this issue?
    Are you still under warranty?
    Be AWESOME Everyday!
    Donate KUDOS and Click "Accepted Solution"
    Did someone help you today?
    Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"
    This will help the rest of the Community with similar issues identify the verified solution and benefit from it.

  • What would cause a slim horizontal line across the screen of my iMac?

    There is a slim line across the Center if the screen. It is horizontal. It does not appear every time I boot up, but it is causing concern.

    Welcome to Apple Support Communities
    It would mean that your display or GPU are starting to fail, most likely the GPU, as the line is not permanent. Does the line move during the time your iMac is turned on or change if you start up in safe mode (holding the Shift key while your Mac is starting)?
    A good test you can do is to make a screenshot of the screen when your iMac is showing the line. To make the screenshot, press Command, Shift and 3 keys, and the screenshot will appear in the desktop. Double-click it and see if the line appears. If it appears, it's the GPU. If not, it's the display

  • My Classic developes two thin horizontal lines across the top third of the screen.

    After a day using my classic in the car, I plugged it into its speaked dock and niticed two thin horizontal lines all the way across the top third of the screen.
    Does anyone know how to get rid of them pleaase. Thx

    You can try Resetting the iPod, won't work, if LCD screen is damaged or the display chip surface mounts has gone wobbly, which mean going in for servicing.
    Otherwise.
    Press Menu and Center button for 10 secs till the Apple logo comes on, then release the buttons.

  • Well, in two weeks I have gone through 2 mini's.   The first had a 1 inch wide shaded zone top to bottom.  Apple replaced it .  Now, the replacement has started with white flickering lines at the bottom. anyone else exper. probs?

    The Ipad mini replacement (the first had a 1 inch shaded band running down it - and Apple replaced it.  Now my new one has a flickering set of lines at the bottom of the screen.  I reset adn reloaded, powered it down and up and still there.  Seems likely to be a hardware issue - just wondering if anyone else has experienced this.   Nothing unusual - havre Mac Airbook, two other older ipads and iphone and all are fine - no issues charging or such.

    You must be at the end of the bell shaped curve for device problems.  There's always someone who experiences this, and unfortuantely you are the rare user to be annointed by the gods of bad luck.
    I read many Apple forums, and your story is indeed rare.  Just like the person who wins the lotto, there are those who play all their lives and never win anything, not even $1.00.  I'm sure you get the picture.  I had a similar experience many decades ago, only with a car (or cars).  Not fun and not funny.

  • Blue line at the bottom of my display

    My MacBook locked up (I couldn't eject a DVD nor could I turn the machine off) so I had to remove the battery to turn the machine off. When I turned the machine back on (1) the MacBook's display remained dark and (2) my Cinema Display had somehow changed its display resolution to 800x600. I fixed the Cinema Display's resolution easily enough and got the MacBook's display running by changing its resolution to 1280x768 (60 Hz). I don't know what the original MacBook display resolution was, but 1280x768 appears to be it. The problem is that now there is a half-inch wide light blue line running across the bottom of the display.
    What should I be doing to get rid of that line?
    Any help is appreciated.
    Don

    The computer appears to have worked out the problem itself. After hitting "Close" and then restarting (as opposed to selecting "Restart"), the display menu came up with "Cinema Display" and "LCD Display" windows set at 1280x800. Everything's back to normal. The puzzling part of this was that prior to shutting off the machine, the display menus were "Cinema Display" and "Display" (not "LCD Display"). I don't know where the "Display" window came from, but now it's gone and things work fine.
    Thanks,
    Don

  • Horizontal lines across the screen of my Vision:M, need he

    I have had my player since Janauaryexcuse me, February and have not had a single issue until today. I turned it on, and there are thin, horizontal, white lines running across the screen. They seem to be most intense over the text at the top left hand corner and if there is any text or picture in the main portion of the screen. I have no idea what has caused and what, if anything, I can do to fix this. I haven't dropped it, had it near any magnetic or other electronic devices, left it in excessi've heat or cold or... anything. I've been babying this thing and now the screen is barely readable when on. Anyone know what's up with this Will I have to return this for repairs Message Edited by appetencexx on 09-26-200709:02 PM

    I bought one on December 24th 2006, didnt drop it or abuse it, after 4 months the same thing happened, I was out of luck because the 3 month labour warranty was up.
    I was told by creative to mail it to their office at my own expense blah blah blah. A quick google search informs me it is a common problem and creative pretends it's your fault the unit has become useless, people also had horrible experiences with creative tech support, so after spending upwards of $400 already to purchase the Vision M 60GB, I decided I wasted enough money and time with this company and I now use the unit as a fancy 60GB portable hard drive.

  • Flickering horizontal lines across the screen

    My Toshiba LCD TV has a thin black line going across the screen. TV is just a year old and is not under warranty. I've seen some comments that the LCD panel needs replacing. Is this my only option? Any other thoughts? Thanks.

    Our Toshiba Regza  Cinemax TV has been acting up, it has shadowing, sometimes horizontal and vertical lines. They are worst on the left side of screen.  Anyone know what part may need to be replaced.  This has been doing this for quite a while, it comes and goes.  Paid almost $3,000 for this piece of crap it should have lasted more than five years.

Maybe you are looking for

  • Time Machine fails to backup home space.

    Summary: I've been having problems with Time Machine since I enabled it. For some reason it refuses to backup any file in my account (/Users/ritchiem/). I have spoken with the an Apple 'Genius' and they were dumb founded. So I ask here in the hope th

  • Why do the colors in images embedded in word (TIFF/JPEG) export off-color from Acrobat?

    I chose this forum as opposed to the printing and pre-press forum because I have a very limited existing knowledge of color space and profile matching and I didn't want to be (1) shunned and (2) overwhelmed by the level of technical detail. When I at

  • Address book not launching -

    How can I re-install address book as it will not launch since trying to install and uninstall Plaxo? I have gone to /library/application support/and there is no address book subdirectory or files. Please give this untechnical guy some help on how to

  • Resubmit in B2B

    Hello All, I added follwoing configuration in my tip.properties, but the resubmit doesn't happened as I expected. And I have not received any emails once resubmit failed. #Resubmit oracle.tip.adapter.b2b.data.ReSubmit.HostmailId = [email protected] o

  • Extract *.tar.gz file, error tar: 0511-164 There is a media read or write b

    when try to: $gzip -dc /dbdump/patch/oraInventory_BK.tar.gz | tar xf /tmp/t tar: 0511-164 There is a media read or write block size error. how to unzip/ extract tar sucussfully? AIX box thanks