White Led 3 Blink and mac doesn't start

I have a new macbook pro whit leopard.
when I turn it on, it doesn't boot.
I can only see a grey screen and Apple start sound.
The white led on the open button blinks 3 times.
I need turn it of and on for 3 or 4 times before it can boot!
It does this whit power cable, and battery.
what can I do?
Message was edited by: ElBartolomeo

I have removed and reinstalled the ram, but it wasn't this.
I have reset RAM (appleoption+rp), but it wasn't it.
I try to do the hardware test (disc 1 + D at the startup) buy it is not capable to complete it. It isn't capable to complete memory test (the first step)
Another problem of this mac is that the monitor shut down after few minutes of using (near ten minutes). Light monitor is ON, but i see all black...
I have tasted that between monitor and keyboard, the chassy is very hot. It Burn!!!
I think that is arrived the time of bringing it to the assistance.

Similar Messages

  • Often my iphone4  just got off and it doesn't start for 2/3 day what is the problem and how can i fix it?often my iphone4  just got off and it doesn't start for 2/3 day what is the problem and how can i fix it?

    often my iphone4  just got off and it doesn't start for 2/3 day what is the problem and how can i fix it?

    The Basic Troubleshooting Steps are:
    Restart... Reset... Restore from Backup...  Restore as New...
    Restart / Reset
    http://support.apple.com/kb/ht1430
    Backing up, Updating and Restoring
    http://support.apple.com/kb/HT1414
    If you try all these Steps and you still have issues... Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
    Be sure to make an appointment first...

  • Satellite A100 - Windows and BIOS doesn't start after BIOS update

    Hello, I have updatet BIOS of my notebook sattelite A100.
    After updating I cannot start my notebook and BIOS doesn't start.

    Hey guys... I tried to update my girlfriend's BIOS on a A100 just now (the windows installer) and the procedure stoped in the middle because windows crashed while doing. Now the laptop won't start at all (obviously). I have a black screen when turning it on. No boot sounds or anything. I've already removed the AC power source and battery in case that works. I guess removing the BIOS battery won't help either since the flashing was wrong... In case that doesn't work, is there any chance i could find a BIOS from ebay or somewhere else?
    Thx in advance, Jimmy..
    PS. My gf is going to shoot my brains out :P

  • Mac Mini LED blinks and shuts down at startup, takes 2-3 tries to boot...

    I have a Mac Mini PPC 1.42GHz. When i boot it up after non-use (cold), the LED blinks once per second and it boots all the way into MacOS and shuts down several seconds later. It will usually do the same thing the second time around. On third boot its usually fine. Not thinking its related, I have reinstalled MacOS anyways. No good...
    Thanks,
    Rich

    Welcome to Apple Discussions!
    The flashing LED is usually indicative of a power-on self test failure, normally leading to the system failing to boot at all. Once per second would indicate the system fails to recognize available RAM.
    The fact this happens when the system is cold (with an implication that it doesn't happen when the system is warm) might indicate the RAM module is no longer firmly inserted, or that the contact face on the pins has oxidized slightly. In this situation, I'd begin by opening the system and removing and then reseating the RAM - in the G4 minis this is relatively easy since there is only one RAM slot, and it is exposed with just the top of the casing removed.

  • Toshiba 40 BV 700 G - Doesn't turn on! White LED blinking!

    hi, my toshiba tv cannot be turned on! When I plug it in and turn it on on the main switch on the back, the white led in the front just keeps blinking!! Please help!

    That doesn't appear to be a US model, and this support site is only for Toshiba US. Try checking on the Toshiba website for your region. You can select your region at the Toshiba : Worldwide Top Page.
    - Peter

  • I put a windows xp cd in my mac book pro and rebooted the mac,mac doesn't start up any more and the cd doesn't come out,what can I do now?

    I put a windows xp cd in my macbook pro and rebooted the mac,mac doesn't come up any more and the cd doesn't come out,what can I do now?

    Hossein,
    As Guido said, you can  use BootCamp to partition the drive. If you want to install, or reinstall Windows. You would launch BootCamp and it will actually guide you through the installation, you will only need to decide how large a partition you want. I would use BootCamp, I would not use disk utility. When you have installed Windows and you want to boot into windows, when you start your MBP hold down the option key, this will give you trha option of booting Mac OSX or Windows.
    Joseph

  • I Mac doesn't start up after OS Leopard reinstallation

    Hello,
    I had Kernel issue and had to reinstall OS Leopard.
    After successful reinstallation, I restarted my I Mac, however, it doesn't start up completely and keeps loading for the last 6 hours.
    Please could you advise what is the issue and how to handle it?
    Thanks, Igor

    First of all, do you have a working back-up of all your files?
    Do you have any devices connected other than keyboard/mouse/trackpad? If so, try starting with them disconnected.
    If that didn't work, and I know you've tried some of these things already, I think I would have one last go with:
    Resetting the SMC & PRAM:
    SMC Reset
    Shut down the computer.
    Unplug the computer's power cord and disconnect attached devices.
    Wait fifteen seconds.
    Attach the computer's power cord.
    Wait five seconds, then press the power button to turn on the computer.
    Reset PRAM
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P and R.
    You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.
    Another go at a Safe Boot:
    http://support.apple.com/kb/ht1455
    And if that fails re-install the OS using the Recovery HD. Good luck.

  • I have updated itunes but now it gives an error r6034 (runtime error) and itunes doesn`t start

    I have updated itunes but now it doesn`t start. I have removed all apple components and reinstalled itunes, but gives the same error: r6034 Runtime error.
    Now i cannot use itunes. Anybody can help me?
    Thanks in advance.

    Hello iTunes_Bad_Update,
    The following article provides information and troubleshooting steps that can help get iTunes back up and running.
    iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
    http://support.apple.com/kb/TS1717
    Cheers,
    Allen

  • Apple TV flashing white led flashing and on TV shows to connect to iTunes

    My Apple TV is flashing white Led and on tv it is showing to connect the AppleTv to iTunes.

    Apple TV (2nd and 3rd generation): Restoring your Apple TV

  • BlackBerry Curve 8330 won't boot, LED blinks and hourglass spins

    I bought this pink BlackBerry Curve 8330 in December of 2008. It has worked perfectly since and I've never gotten it wet. It's been dropped 4-5 times, but never from more than 3 feet.
    This afternoon, in the middle of writing a text, it suddenly powered off and the red LED light came on like it does when it is turning back on. It went off, the screen stayed black, then a few seconds later the screen turned on with an hourglass spinning for about five seconds, then the light turns off and everything goes black again for a few seconds, then the LED light comes on again and the cycle is repeated. It did this five times before I had to put it away as we drove home. When I got home, it had finally booted the whole way, but the battery was so low the radio was off, so I plugged it into the USB charger on my desktop computer.
    When I came back later, the phone had stopped charging and was on a black screen with the LED light on, just like earlier. It went through this cycle a few times.
    I pulled the battery and put it back in, same thing happened. Black screen, white screen with hourglass, black screen.
    I plugged it back into the USB charger and as I type this, the little psycho has booted completely and it shows that it is charging.
    Device info
    Your carrier: Telus Mobility
    Model info and OS version: v4.5.0.186 (Platform 3.4.0.59)
    Apps and free space
    File free before and after a battery remove/replace.: 28042909 bytes / same
    Did a battery pull fix your issue? No
    Apps installed and their version if possible.: Too many to type out right now, but the latest ones to be updated were SocialScope Lite v0.9.6.20, BlackBerry Messenger 5.0.2.12 (both updated automatically)
    BT device model/version (you will have to look at the BT device): No bluetooth (hope that's what BT stands for)
    How can I fix this so it doesn't keep happening? Thanks so much in advance.

    Hi and Welcome to the Community!
    Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain connected to a known-good wall charger (not PC USB):
    With the battery inside, connect your BB to the wall charger
    Leave it alone for 2 hours, no matter what the LED or the display does
    Remove the battery
    Wait 15 minutes
    Insert the battery
    Wait another 2 hours, no matter what the LED or the display does
    This has been known to "kick start" some BBs.
    It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
    Obtain a known good and already fully charged additional battery...use it in your BB and see what happens
    Obtain access to a known good and identical BB...use your battery in it and see what happens
    The results of this will indicate if it's your BB or your battery that has the problem.
    Good luck and let us know!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Nokia C3-01 - white screen blinking and won't turn...

    Yesterday evening I wanted to make a call and took the phone but the display was just blinking with the screen completely white and didn't respond to any keys (actually I couldn't turn it off, so I had to remove the battery). After placing the battery back after some time nothing changed, it still blinked. I tried to remove it for the whole night but no success again. Everything is still the same. This happened to me about a month ago for a couple of times and after few days it started to act normally. What's the problem with my phone? Can anybody help me and tell me what to do?
    Thank you in advance

    it happened to me too. 2-3 weeks after i bought my new c3-01 screen gone white and never returned. I went to a nokia service store and after 2 weeks i got it back with a software update ''they told me'' . After a couple of days again tha same problem! back to nokia store and again 2-3 weeks of patience they replaced my c3-01 with another one. They said that the problem was on the electronic board (i dont know if im saying this right)! I have the replaced phone for about 2 weeks. No problems yet its very early anyway...

  • Iomega StorCenter ix2 white LED blinking after fw update

    Hi,
    today I tried to update the firmware of my ix2, don't know if it is the ix2 dl as the case looks like this http://shop.lenovo.com/de/de/servers/network-stora​ge/lenovoemc/ix2/ but with StorCenter instead of ix2-dl written on the front. As Version 3.3.2.24208 was installed, I manually uploaded ix2-ng-3.3.2.29823.tgz as a first update step to be able to update to 4.0.6.19294  in the next step as recommended in the FAQ. 
    see https://lenovo-eu-en.custhelp.com/app/answers/deta​il/a_id/31178
    But after successfully deploying the new firmware and the automatically reboot, the device sticks to a glowing blue HDD LED and a blinking white power LED. I read about the chance to boot from an USB flash drive but I can't find the image to prepare the USB flash drive.
    Can you please provide me with this image or tell me what I can do to access my device again?
    Thanks.

    You can put the serial number in the box under "Find Your Product" to see if it is in warranty still. If you still have the original purchase receipt, you can contact technical support and they will update the warranty if it is still within the warranty period. Unfortunately, only technical support can provide the link for the imager as you have to sign a non-disclosure agreement.
    Have questions and need answers?
    Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
    LenovoEMC Support & Downloads
    LenovoEMC North America Support Contact Page

  • My printer has a ornge led blinking and does not allow me to print any document. how can I fix it?

    My printer is showing an error and the orange led is blinking ans dos not allow to print any document

    Hello HP-1400. I understand your printer is an error state, which is preventing you from printing. I will do my best to assist you! Please provide the following information so I can perform troubleshooting:
    The printer model number. For assistance in locating this information, please reference this HP document: http://h10010.www1.hp.com/ewfrf/wc/document?cc=us&​lc=en&dlc=en&docname=bpy21016
    Your operating system. If you require assistance locating this information, please reference this website: http://windows.microsoft.com/en-CA/windows/which-o​perating-system
    Please respond as soon as possible. I'm only here to help!
    Mario
    I worked on behalf of HP.

  • Mini mac doesn't start up

    today my mini won't start, did the book restarts. still nothing! just got start up tone and folder with ?....disk eject not ejecting need help????

    Hi Cyrk_mac,
    Welcome to Apple Discussions
    You may need to reinstall your system software from the install discs. You should look at Knowledge Base Document #106214 on Troubleshooting Startup Issues.
    Jon
    Mac Mini 1.42Ghz, iPod (All), Airport (Graphite & Express), G4 1.33Ghz iBook, G4 iMac 1Ghz, G3 500Mhz, iBook iMac 233Mhz, eMate, Power Mac 5400 LC, PowerBook 540c, Macintosh 128K, Apple //e, Apple //, and some more...  Mac OS X (10.4.5) Moto Razr, iLife '06, SmartDisk 160Gb, Apple BT Mouse, Sight..

  • How to speed up applications and Mac OS X start?

    hello there, I find my applications start too slow on my Macbook pro Core Duo despite a T7400 Intel processor, 2,16 Ghz .Is Mac OS X for Intel Core Duo really optimized and his applications too? How can I speed up the performance of applications? I'm newbie. I 'd like to have advice, reports and suggestions. Thanks

    Application and OS start times are not uniform. Due to heavy use of caching, start times are initially long, but get shorter as time goes on. For example, if you install OS X or a system update that changes the system, the next restart may be very long or may involve a double restart. The next time you restart will be faster, and subsequent startups will be faster still. This is because OS X will progressively build up a startup cache of the items that start up, so they don't have to be loaded from nothing each time. OS X startup times should get shorter until you modify the system again due to an update or installing a new kernel extension.
    Applications are similar. Photoshop, for example, takes a long time to start the first time after a system restart. If you exit Photoshop and then start it again, the second time starts up faster. Again, OS X is caching the application data in RAM, but that gets thrown out if you restart. If you restart your computer, Photoshop startup time is back to the longer first-time duration.
    My Mac laptop is much older than yours, but it starts up in 35 seconds and applications can start in a few seconds if I've already started them once during the current session. I, and many other Mac users, avoid restarting the machine unnecessarily. Because OS X is based on Unix server software, it is designed for long times between restarts.
    I will typically restart or shut down my Mac every week or two. This gives you two advantages we have been talking about: You never wait through the startup time because you are only waking it from sleep, and it means the caches for the current session can stay in use and not get thrown out on restart, so application startup times stay short.
    Try using your Mac by simply sleeping it when you don't want it on, instead of shutting it down, and see if that makes any difference. If it does not, there is a possibility that you don't have enough RAM for the types of applications you use.

Maybe you are looking for