White light sources (and their quality)

(continued from another thread)
White LEDs are currently not a great way to illuminate your prints because they are not near full spectrum light sources.  Most "white" LEDs are currently blue or violet LEDs with a green or yellow phosphor added to look neutral - but they have very little light in other areas (especially red).  Some high end white LEDs are getting closer to full spectrum - but those are only recently available, and are not yet widespread.
Cheap fluorescent lamps tend to have a few "spikes" of light and have some wavelenths almost entirely missing.  "Full Spectrum" Fluorescent lights are getting better, and cheaper - but are still not comparable in quality to tungsten or daylight.
Spectra measured with X-Rite ColorMunki and Argyll CMS spotread utility. Multiple readings averaged, normalized and plotted in Microsoft Excel.
[ updated Dec 16, 2012 to add white LED4, a recent Cree flashlight LED ]
[ updated May 27, 2013 to add samples from 2 LED lightbulbs ]

(1)
http://www.fho-emden.de/~hoffmann/prooflight18092003.pdf
(2)
http://www.fho-emden.de/~hoffmann/fluorescent02062006.pdf
Some additional information (2006):
(1) shows spectra for proofing light by Just (fluorescent) and Solux (tungsten)
and related topics.
(2) shows spectra for commercial fluorescent tubes.
Illuminance E (lux, lx) and luminance L (candela/m², cd/m²) can be related only under
certain assumptions (isotropic diffuser). The one gets (Hunt, Measuring Colour):
L / (cd / m²) = (1/pi) E / lx
or simplified 
L = E / 3
Monitor           L = 100 cd/m² (luminance)
Office desktop E = 500 lx      (illuminance)
Proofing light  E = 2000 lx  (according to some standard for critical inspection)
We can see immediately, applying the rule of thumb, that paper prints cannot
be viewed side by side with monitors with good results:
2000/3 = 666 (print)  <---->  100 (monitor)
The ambient light at the working place in my environment is about 50 lx !
Proofing light is available in a neighbour room.
Best regards --Gernot Hoffmann

Similar Messages

  • When I come from outside and press the home button to turn my iPod on, there is white, light blue and red lines but it is transparent enough that I can see my background, time, etc. It hasn't been water damaged, so that cant be the problem.

    When I come from outside and press the home button to turn my iPod on, there is white, light blue and red lines but it is transparent enough that I can see my background, time, etc. It hasn't been water damaged, so that can't be the problem. I was thinking maybe it is just because of the cold but, I don't like having my iPod doing that whenever I come back from the cold. However, I was in class too and this problem happened but it was inside! So I am very worried, I have dropped my ipod a few times but it hasn't fallen that hard to effect it.

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up                                                                
    - Restore to factory settings/new iOS device.             
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar                                      

  • ZBAPI to display Supply source/vendor/material and their descriptions...

    Hi Frnds,
    I need to write 3 ZBAPIs to list (1)all supply source and their text (2)all vendors and their text,(3)materials and their text
    by calling some std Fm in the source code.
    IF you know any STD BAPI/ RFC FM/ FM to get those datails, please  provide me...
    Note: I shd get all existing vendors with their texts. i.e., what we get when we press F4 like that.
    Regards,
    Kiran.

    Hi Frnds,
    I need to write 3 ZBAPIs to list (1)all supply source and their text (2)all vendors and their text,(3)materials and their text
    by calling some std Fm in the source code.
    IF you know any STD BAPI/ RFC FM/ FM to get those datails, please  provide me...
    Note: I shd get all existing vendors with their texts. i.e., what we get when we press F4 like that.
    Regards,
    Kiran.

  • Macbook black screen, white light, no chime and more problems

    When I completely shut down my Macbook (regular starting 2009) and turn it back on I see the white light only and black screen. Nothing works! this has happened two times and I pressed the power button for 10 seconds to do a PMC reset and it actually turned on and past this week I've been pressing SHIFT+PWR button to turn on my Macbook.
    Also, when my macbook wakes up from sleep it takes a while to get back up and sometimes the sound dosen't work although I see the devices in the Audio MIDI.
    Does this mean my logic board is going bad or is it a NVRAM problem? I tried resetting the NVRAM but it didn't work!

    Have you tried running the Apple hardware test?  Run the extended test, which can take over an hour.

  • White light plz help

    I have a 500mhz indigo imac when i press the power button it blinks a white light once and doesn't turn on i opened it up thinking maybe the button was stuck making it stay in sleep mode but it's not plz help me thanks.

    No chime can be a symptom of a flat logic board battery.
    Perhaps the RAM is bad, but that's unlikely if the machine worked before. Try reseating RAM or removing everything but the stock RAM.
    If it's not that, then go here and download the appropriate manual for your iMac, and follow the troubleshotting steps:
    http://www.whoopis.com/computer_repair/
    Opening the Mac can potentially expose you to up to 26kV of voltage. Make sure you know what you are doing before attempting DIY repair on an iMac or any CRT.

  • NI DAQ CARD FORSCANNING PV MODULES WITH 10mA lIGHT SOURCE

    WHICH TYPE OF NI DAQ USB CARD FOR SCANNING PV MODULES WITH 10mA lIGHT SOURCE AND WHICH SENSORS CAN BE USED?
    THANKS!
    Solved!
    Go to Solution.

    ellisemuhire,
    How many analog voltage input channels will you need to read?  What is the range of the signal you will be reading?  How frequently will you need to sample the input signal?  How many bits of resolution do you require?  We have USB options that can read analog voltage with 12, 14, and 16 bits of resolution.  
    Here is a link to our USB Multifunction DAQ cards.  I can make a suggestion for you if you have these details.  
    Regards,
    Jared R.
    Precision DC Product Support Engineer
    National Instruments

  • HT1600 I have Apple TV version 7.4.2 and we pressed on the remote the select button and the menu button at the same time to update our software.  The box shows white light, we can get the screen to select netflix but nothing will move and the box will not

    I have Apple TV version 7.4.2.  We read in a blog that in order to reset our Apple TV we should press the menu button and the select big button at the same time which we did.  Now when we attempt to turn on the apple tv box it with the remote we get a white light and sometimes we can get the menu screen but the remote will not let us move now will it allow us to turn the apple tv on or off.  If we just leave it alone, the white light eventually goes away.  I did unplug the apple tv and we removed the batteries and reinstalled them from the remote and that did not make any difference.  Please advise. 

    If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
    Connect the micro USB cable to the Apple TV and to your computer.
    Reconnect the power cable (only for Apple TV 3)
    Open iTunes.
    Select your Apple TV in the Devices list, and then click Restore.

  • White flare/stripe on photos from direct light source

    I have a problem very similar to this https://talk.sonymobile.com/t5/Xperia-Z3-Z3-Dual/White-stripe-on-photos/td-p/909906 but i am not using flash. White stripe only shows when light is coming direct to camera from a light source like fluorecent lamp and from a particular angle.
    Stripe shows in both portrait and landscape mode and always at same place. I am attaching 2 photos 1 taken in landscape and other in portrait.
    I have a protecting cover but it is not covering the camera lens.
    I think other z3 devices do not have this issue as i have searched a lot but i only found 1 other person facing this issue and i have shared the link above. 
    Can i know why this stripe shows on photos? Is it a known issue? Should i claim warranty?
    landscape
    Portrait

    Few other things to check/try
    settings > apps > all > camera > clear data > restart your phone 
    also you could repair your phone with PCC which I doubt it will make any difference 
    PC Companion (PCC)
    Bridge (for Mac)
    Alternatives on How to backup Xperias
    http://talk.sonymobile.com/thread/36355
    if nothing work contact your local Xperia Care
    http://support.sonymobile.com/global-en/contactUs/
    "I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

  • My ATV is not displaying on my TV.  My network is working, my software is up to date, ATV turns on and the white light does not flash.  I have recycled all my equipment and it is still not responding.  All the settings are correct as well.  I am puzzled.

    My ATV is suddenly not displaying on my TV.  My network and Internet connections are all working, my software is up to date, the ATV white light is on steadily, all my settings are correct and I have power cycled all my equipment.  Is there something more I can do, or is it possible my ATV needs repair?

    it might
    for my appletv to display on my tv I have to choose the hdmi port i have connected to as input source
    I do that using my tv remote
    how depend on the tv
    before taking it back you should also test with another hdmi port and another tv (friend of family) to verify that it is indeed broken

  • HT1551 just updated my apple TV and whit light is flashing continuously and nothing is on the screen anymore.

    Can anyone help with this please?
    Just updated the Apple TV and the white light is now flashing quickly and nothing is on the screen.  Can't access it with the remote from the Ipad.

    Same problem here.  Long time Apple fan, own lots of their products... Greatly disappointed.
    Bought a brand new Apple TV, worked fine for 3 days but then the picture went blank (possibly after an auto update?) and I observed a quickly flashing white light on the Apple TV.  Manual indicates this means it is "having problems" (no kidding) and recommends restoring the software via a micro-USB cable (cable not provided).
    Acquired a cable and attempted this fix but after following the procedure the Apple TV never showed up in iTunes, so I'm unable to perform the restore.  Returning the device today, not sure if we want to get another or just give up and save the $100.

  • HT3180 Uploaded new software update and all I have is a little black box with an incessant flashing white light. I have pushed menu + downarrow on the remote, unplugged for 10 seconds and stiill no change when I plug it in again ! !

    Uploaded new software update and all I have is a little black box with an incessant flashing white light. I have pushed menu + downarrow on the remote, unplugged for 10 seconds and stiill no change when I plug it in again ! !

    Welcome to the Apple Community.
    If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
    Connect the micro USB cable to the Apple TV and to your computer.
    Reconnect the power cable (only for Apple TV 3)
    Open iTunes.
    Select your Apple TV in the Devices list, and then click Restore.
    (You may already have a micro USB cable if you have a camera or other digital device)

  • HT1320 Help! My ipod classic is frozen. Even when I attach it to a power source and try to reset it (as per the instructions above), the apple logo never appears. The only thing that happens is that the screen turns alternately light and dark. Thanks!

    Help! My ipod classic is frozen. Even when I attach it to a power source and try to reset it (as per the instructions above), the apple logo never appears. The only thing that happens is that the screen turns alternately light and dark. Thanks!

    If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
    http://docs.info.apple.com/article.html?artnum=60983
    If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
    Make sure you do all the following “TRYs”
    A. Try to wait 30 minutes while iPod is charging.
    B. Try another FireWire or USB through Dock Connector cable.
    C. Try another FireWire or USB port on your computer .
    D. Try to disconnect all devices from your computer's FireWire and USB ports.
    E. Try to download and install the latest version of iPod software and iTunes
    http://www.apple.com/itunes/download/
    For old and other versions of iPod updater for window you can get here
    http://www.ipodwizard.net/showthread.php?t=7369
    F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
    http://www.apple.com/support/ipod/five_rs/
    G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
    http://docs.info.apple.com/article.html?artnum=93651
    If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
    Intermediate Level
    A. Try to connect your iPod with another computer with the iPod updater pre-installed.
    B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
    For Mac computer
    1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
    2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
    3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
    4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
    5. Eject your iPod and do a Reset
    6. Open the iTunes 7 and click “Restore”
    For Window computer
    Go to folder “My Computer”
    Hope you can see your iPod there and right click on the iPod
    Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
    Now select “Format”
    Eject your iPod and do a Reset
    Open the iTunes 7 and click “Restore”
    In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
    http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
    C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
    Tips
    a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
    b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
    c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
    http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
    Advance Level
    A. Diagnostic mode solution
    If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
    You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
    Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
    iPod 1G to 3G: "Menu" and "Play/Pause"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
    The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
    iPod 1G to 3G: "REW", "FFW" and "Select"
    iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
    You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
    Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
    B. Format your iPod with a start disk
    I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
    If none of these steps address the issue, your iPod may need to be repaired.
    Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
    Or visit your local Apple Retail Store http://www.apple.com/retail/
    In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ or ifixit at your own risk
    http://www.ipodresq.com/index.php
    http://www.ifixit.com/
    Just in case that you are at the following situation
    Your iPod warranty is expired
    You don’t want to pay any service charges
    You are prepared to buy a new one
    You can’t accept the re-sell value of your broken iPod
    Rather than leave your iPod as paper-weight or throw it away.
    You can try the following, but again, only do it as your last resort and at your own risk.
    Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
    Last Resort Level
    1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
    In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
    http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
    2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
    http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
    Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
    2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
    Exclamation point and folder and nothing else
    Spank your iPod
    http://www.youtube.com/watch?v=3ljPhrFUaOY
    http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
    Exclamation point and folder and nothing else
    http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
    What should I do with my iPod? Send it or keep it?
    http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
    Strange error on iPod (probably death)
    http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
    Sad Face on iPod for no apparent reason
    http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
    Meeting the Sad iPod icon
    http://askpang.typepad.com/relevant_history/2004/11/meeting_the_sad.html#comment -10519524
    Sad faced iPod, but my computer won’t recognize it?
    http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
    iPod Photo: unhappy icon + warranty question
    http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
    4th Gen iPod Users - are we all having the same problem?
    http://discussions.apple.com/message.jspa?messageID=2235623#2235623
    Low Battery, and clicking sounds
    http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
    Sad faced iPod, but my computer won’t recognize it
    http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
    Sad iPod solution
    http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
    Re: try to restore ipod and it says "can't mount ipod"
    http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
    iPod making clicking noise and is frozen
    http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
    Cant put it into disk mode
    http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
    I think my iPod just died its final death
    http://discussions.apple.com/thread.jspa?messageID=3813051
    Apple logo & monochrome battery stay
    http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
    My iPod ism’t resetting and isn’t being read by my computer
    http://discussions.apple.com/thread.jspa?messageID=4489387#4489387
    I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
    Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
    Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote

  • I have a powermac dual g5 2.0 that wont start up.When I plug it in I get the click from the power supply. When I hit the start button, the white led on the front panel lights up and stays lit. No whir sound from the hard drive or the fan. No lights on the

    I have a powermac dual g5 2.0 that wont start up.When I plug it in I get the click from the power supply. When I hit the start button, the white led on the front panel lights up and stays lit. No whir sound from the hard drive or the fan. No lights on the motherboard

    The click usually indicates a big problem, but...
    How to reset the SMU/PMU on a Power Mac G5 (Late 2004) or Power Mac G5 (Late 2005) ...
    http://support.apple.com/kb/HT1436
    Earlier G3, G4, G5 models...
    http://support.apple.com/kb/HT1939
    Might be time to replace the PRAM Battery, 4 years is close to their lifespan, far less if ever without AC power, & can cause strange startup problems...
    See which one your G5 has...
    http://eshop.macsales.com/item/Newer%20Technology/CR2032/ 
    http://eshop.macsales.com/item/Newer%20Technology/BAA36VPRAM/ 

  • Unit crashes and white light flashes very fast and tv screen goes blank

    Apple TV crashes after a half hour of viewing and white light continues to flash very fast and tv screen goes blank

    Welcome to the Apple Community.
    If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
    Connect the micro USB cable to the Apple TV and to your computer.
    Reconnect the power cable (only for Apple TV 3)
    Open iTunes.
    Select your Apple TV in the Devices list, and then click Restore.
    (You may already have a micro USB cable if you have a camera or other digital device)

  • HT4356 How can I print a greyscale/fast document from my iPad wireless printer. It will print in color and high quality but want black and white

    How can I print a greyscale/black and white document from my iPad wireless printer???
    IT will print in COLOR and high quality print but would like to conserve ink (Esp. Coloured )
    is there a way to reconfigure settings either on my iPad or the printer ??? Cannot find a setting
    when u select print on the ipad it dos not allow you to change your settings before you print

    There is no setting for this. You can request it here:
    http://www.apple.com/feedback/

Maybe you are looking for

  • How to build a plug-in for FCP

    I want to build an export plug-in for FCP. It is a little similar to Automatic duck export plug-in. I want to export sequence in my own format. The version of Final Cut Pro is 6.0. I downloaded FxPlug SDK, but it is only about video effect, not what

  • Dealing with weird versioning

    Hi, I'm making a PKGBUILD for EiffelStudio, a IDE for the Eiffel language. Everything works fine so far, however the versioning scheme and package URL are kind of weird. For example, the current version of the tarball is called "Eiffel66_gpl_82484-li

  • Files to large

    I searched through daisy disc and found out that most of my HD films are around 8-9-10 GB each. On the description on Itunes they are ment to be around the 4GB mark. Can i make these smaller or can i delete part of the file. I have had a look in the

  • Settement of cost of one GL (Cost element) to one single reciever GL

    Dear All, We have business requirement that we want  to settle cost of one specific GL (CELEM) to one specific GL only. So, I have tried to map the same in Allocation structure the same relevant cost element in sender and another one in Settlement co

  • My calendar preferences will not open.

    When I am in Calendar i can not get Preferences to open no mater how many times I select it under Calendar. What is wrong and how do I fix it.