White Macbook gives Flashing Question Mark on Startup

Hi,
I'm in need of some advice & help in what to do with an old White Macbook (06/07 vintage).
I gave this to my mother a few years ago to bring her into the internet age while I conveniently bought a Macbook Pro
A few days ago it stopped working and on startup gave the flashing question mark symbol.
I read through various forums and discussions and have performed the following:
Held the option key down during startup - Resulted in being able to see the mouse pointer but no icons
Inserted the original startup disc (OSX 10.4.8) while holding down C on startup - I decided to go ahead and reinstall the original OSX and upgrade it after everything was back to working. However at the step where you 'Select destination' there is nothing to select. Its as though there is no hard drive on the macbookI selected Disk Utilities at that point and tried to verify the drive (as I could select it at this point) but an error message appeared and said that the volume needed repair. I then tried the repair Disk option but the process stopped almost immediately with the following error:
1 non HFS volume checked
1 volume could not be repaired because of an error
I have held down the D key during startup to get a diagnostic of hardware but this has not worked.
I would like some help with diagnosing what may be wrong to see if its economically viable to repair and get another year or 2 which would be ideal.
Am happy to open up the backside to investigate further if need be.
All help appreciated,
Thanks

I have replaced the hard drive and tried to reinstall OSX but it still does not work. I still cannot select the hard drive in which to install OSX. I tried system utilities but it does not recognize the drive and says there is an I/O error.
I am going to source a HD ribbon cable as a last ditch effort. If its not either then it will be the logic board and that is not economically viable

Similar Messages

Macbook Displays Flashing Question Mark on Startup After Leopard Upgrade

Hello, I have a first Generation Macbook that I tried to Upgrade to Leopard. I put in the install disk and everything went smoothly until I checked on it an hour later and it said "Install Failed" without specifying a reason and it asked me to restart. So, I restarted with the disk in and then the installer claimed it couldn't locate my hard drive. I popped out the disk and now all I have is a flashing Question mark on my screen. I know there is a help article related to this, but I was wondering if there is something different due to this being a result of an attempted Leopard Upgrade, also I was wondering If I do put in the OSX Tiger Disk that came with my Macbook and re-install it will it erase everything I had on the computer?
Thank You Any help is Appreciated!!!!!!!

The Tiger install discs will need to erase your hard drive to allow for Tiger to be installed.

Imac G5 won't start white screen and flashing question mark

tried every key combo recomended - erased HD using target mode/firewire with laptop - but won't boot up from install disc...

The white screen with flashing question mark means that it cannot find a bootable volume.
The iMac G5 will not boot from just any install disk. Ideally, use the grey restore disks which came with the computer. If you've lost these, you can order them direct from Apple. Alternatively, a Mac OS X 10.5 retail install DVD will work provided the iMac G5 has also 1GB RAM (minimum requirement for 10.5).
Sometimes, if the internal drive is faulty, it can take a long time for the computer to recognise other disks. I would suggest holding down the option key on the keyboard (labled alt on some keyboards) and turning the computer on, keep holding alt until you get to the early boot menu, insert your DVD/CD, and click the circle arrow to refresh, wait a bit and the DVD/CD will show up and you can click on it to select it and boot from it by pressing the straight arrow.
After a little while it will get to the install menu, select your language, then on the next screen go through the menus to find "Disk Utility" (it's in different places on different versions of Mac OS X).
You will want to check that the internal hard drive is detected, and that it doesn't have a SMART error (it might be red, or say that the disk is failing). If you get that far, then (assuming you have erased the disk previously, as this will step really will erase the drive and take all your data with it) partition the drive, making sure that under 'Options' you select Apple Partition Map (this will be the default on earlier versions of Mac OS X, but might not be if you've erase the disk from an intel Mac like a MacBook).
Once, you done all that, and there haven't been any issues, you should be able to quit Disk Utility, and carry on with the sytem install as usual, and a 30mins to 2 hours and reboot later you should be booting from the internal drive again.

White screen with flashing question mark

AAll I get is white screen with flashing question mark. I've inserted OS disc but it won't run. Can anyone help plz?

A flashing question mark or globe appears when you start your Mac

A flashing question mark on startup

My Mini is displaying a flashing question mark after startup. How do I fix it?

The flashing question mark indicates that your Mini cannot find a valid startup disk. Restart with the Install disk in place and hold down the C key and the Mini will start up from the CD. Repair the Mini's hard disk using Disk Utility on the Install CD (Look under the Apple menu). If this does not work, you may need to obtain a startup CD with a third-party recovery utility such as Disk Warrior to attempt to rebuild the Mini hard disk directory.
Here's a link to an Apple document to help you:
http://docs.info.apple.com/article.html?artnum=58042
Bob N.
Mac Mini 1.5 GHz; iBook 900 mHz; iPod 20 GB Mac OS X (10.4.5)

Why won't my MacBook Pro start up? White screen and flashing question mark.

Hi,
I've had my MacBook Pro for almost 2 years now and I installed OS X 10.8 about 4 months ago.
Today I turned the MacBook Pro on and a white screen with a flashing question mark appeared. I tried then getting the startup manager up: turning on the laptop and immediately holding in alt (option). But nothing appeared for about 25 seconds until a rotating Earth labelled 'Internet recovery' appeared that gave me options to join wireless connections. However, my internet wasn't in the options and when I tried typing in the information required to join my internet the laptop would just load and never find it.
I then tried putting in my Mac OS X install DVD (10.6.7) and help in C until the apple logo appeared on the screen and the little rotating loading circle appeared. That then disappeared and a cicle with a cross through it appeared (similar to a no entry sign). Then after about 30 seconds a blue screen followed by a grey screen appeared until eventually the disc ran properly. I then went into Disk Utility but there was no option called Macintosh HD, only the discs content. It wouldn't let me first aid, erase or repair anything.
I'm totally stumped and have 4 exams at university within the next 2 weeks. I'd really appreciate it if anyone could help me out here?
Thanks,
Best wishes,
Connor

The support article linked below is somewhat outdated. Where it refers to starting up from an installation disc, you should instead start up in Recovery by holding down the key combination command-R at the chime. Release the keys when you see a gray screen with a spinning dial.
If you don't have a current backup of all the data on the startup volume, and you want to preserve that data, then you must try to back up before you do anything else. Ask for instructions if you need them.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to reinstall OS X from Recovery, if necessary. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
A flashing question mark appears when you start your Mac

Hey, My macbook is giving me a flashing question mark on startup. When I hold down the command key to get to system preferences it asks me for a firmware password, that I did not set! Any ideas on how to bipass this?

Hey, My mac book is giving me a flashing question mark on start up. When I hold down the command key to get to system preferences in order to help it find the system software it asks me for a firmware password, that I did not set! I also do not have the start up DVD/disk anymore. Any ideas on how to bypass this?

Contact Apple or an authorized Apple service provider.
(116347)

File with flashing question mark on startup?

So my MacBook Air just recently started this, with the white screen and grey box with a flashing question mark in it upon starting it up. Safe Boot did nothing, the question mark file continued to appear.
Holding down the Alt button seems to be the only thing that has yeilded any other response. When I hold the Alt button down on startup, it asks me to connect to a wireless internet (which I have). After connecting, it goes into Internet Recovery, where it shows a rotating globe and loads up, usually taking a couple of minutes.
Then I get the white page with the apple logo, and a loading circle.
After that, I get the grey page with Mac OS X Utilities.
From here, I have no idea what to do. My computer was only recently returned to me after a login error, where all my files has been removed and deleted, so it was at Factory settings. Since then, I haven't had enough things on my compter to use Time Machine Backup or anything like that. so I have no backup sources for it to restore from.
I have been able to get onto the internet, but only in a small box on top of the grey background.
I tried to reinstall Mac OS X Lion from here, but when I agree to the terms and conditions, it gives me no disk to install it too, so therefore I cannot continue ahead with the installation.
As for Disk Utility, when I click on the left hand side Mac OS X Base System, there is nothing under First Aid that is highlighted for me to click (show details is also checked)
Nothing under Erase is highlighted for me to click on either.
In the Restore selection, The source (Mac OS X Base System) has Image highlighted beside it. I can click onto that, but from there I have no clue what to do.
This about the sum of all the options my computer is giving me at the moment.
I have no speakers or cords that hook up to my computer (seeing how its a MacBook Air)
As far as I am aware, I have no disks or CDs or external drives that have any programme to help me restore it. I also am not entirely certain what my current systems were, with how up to date everything was, before this happened, but I assume they were all the latest seeing how it was only just fixed a month ago.
If there are any suggestions, your help would be great.
If my files can be saved, that is awesome. But if they have to be cleared, I am not at all phazed by doing that either.

If Disk Utility left panel shows only "Mac OS X Base System", it would seem that it is not detecting your main drive at all.
I would take the system into an Apple Store for diagnosis.

Random flashing question mark on startup

Every once in a while when my mac mini cold boots, I get the flashing question mark. Turning the mac off, and booting it back up again usually fixes the problem. I ran verify disk permission and verify disk; both came back ok. S.M.A.R.T status was always "verified". I have also booted into single user mode and ran FSCK. No problem there either.
I didn't have this problem until I upgraded to 10.6.3. Just wanted to find out if anyone else is having the same issue and if there is a way to figure out what is causing the problem.

On the face of it, this sounds like a temperature-dependent problem: when the hard drive is cold, it either isn't spinning up on the first try, or the calibration is slightly off and the Mac doesn't recognize the drive as being bootable.
When it is slightly warmer (second try) it spins up, or the calibration is now within limits and therefore it boots and now can pass all the DiskUtility tests.
If it were me, I'd make sure that I had this drive fully backed up onto another external drive -- just in case.
(In terms of it perhaps being a spin-up issue, I'll note that I have 640Gig 2.5" external that doesn't always mount when I turn it on. Generally the second time is a charm. I attribute it to the drive not spinning up.)
Just in case the issue is something else, I'd suggest going to Apple Menu > System Preference > Startup Disk and explicitly setting the drive to be your startup drive.
It might also be interesting to hold down the Option key at startup and explicitly choose the drive. Do this for a few days and see if the problem continues to occur. Holding down the Option key should give the drive a bit more time to spin up.

Flashing question mark on startup, plzz plzz help

Hello,
I know there are many post on this topic, but not getting exactly for this machine.
was normal yesterday, today when i turend on, i see flashing question mark with grey folder.
i really need help with this, how can i sort this out? what will be the problem?
i tried holding command key on the restart, it ends with below image...... what is this??
please let me know, i have very important files, i'm worried. your any reply would be appreciated. thanks

The blinking question mark indicates that the firmware could not find a valid Operating System on your machine.
Your harddrive may have failed. Your filesystem may have bcome corrupted.
You may want to seek professional help here. You need to decide how important you data is to you. Be sure to specify that you want your data back.
In addition to the fix your mac places, there are professional firms the will attempt to recover data from a failed harddrive. Recovery does not come cheap.
diy...
I suspect disk corruptions.
verify & repair your startup drive
To verify & repair you file system on the startup drive, you will need to run disk utility from you installation DVD.
This article will tell you how to get to disk utility. Once in a disk utility, you can go and attempt to recover the disk.
http://support.apple.com/kb/TS1417
To repair your startup drive, you will need to run disk utility from your startup DVD.
Mac OS X 10.4: About the utilities available on the Mac OS X 10.4 Install DVD
http://support.apple.com/kb/HT2055
How to run disk utility from your startup DVD.
Insert your startup DVD into your reader. Power down your machine. Hold down to the c key. Power on your machine. This will bootup your startup DVD.
This will bring you to a panel asking you for your language. Pick your language.
You you come to the Install Mac OS panel. Do not install.
Click on Utilities menu item. This will give you a pulldown list of utilities.
Click on the disk utility.
You are now in disk utility. Pick your disk. Click on repair it should be on the lower right of the panel.
Once the repair completes successfully, you should update your permissions.

IMac DV SE 400 chimes, gives flashing question mark. Hard drive bad?

My G3 iMac DV SE 400 will not start up. This is what happens:
1. Startup chime
2. Hard drive starts to spin
3. Hard drive "clicks" once
4. Flashing question mark on screen
I tried resetting the PRAM and disconnecting everything like it says in the manual. I have booted up from CD and used Disk Utility (OS X) and Disk First Aid (OS 9) to find out if the computer "sees" the hard drive. No luck with either one - the drive does not mount. I have also tried System Profiler and the computer does not recognize the presence of any hard drive there either.
Is the hard drive really "dead?" Can it be resurrected - at least to the point where I can retrieve my files, pictures, etc.? I'm confident that the drive is receiving power because it actually starts to spin up (see #2 above). Am I overlooking something easy here? Could it be as simple as replacing the battery? I haven't tried that because the hard drive does "attempt" to start up.
Failing all else, is it possible to retrieve the data using my other Mac even though the hard drive will not boot?
Any help would be appreciated. Thanks.

Well if it spins up you might be able to salvage your data with Data Rescue II (free demo) or Disk Warrior. You could also try Target mode but if disk utility didn't see it then that's probably not going to be any better.
If those two don't see it then your only option is data retrieval via a pro company but that will be very expensive.
Richard

Macbook pro flashing question mark folder, won't recognize hard drive

My 2010 macbook pro froze and after restarting I was greeted with a flashing question mark folder. I then restarted again and held down "option" key and went into Mac OS X utilities then into disk utilities. In disk utilities, my only drive options are "superdrive" "disk0" and a subfolder of "disk0" labeled "Mac OS x Base system". My hard drive is no where to be seen. I also tried to install a new hard drive but the same thing happened, the computer could not recognize that there was a hard drive present. What can I do to fix this??

Hi bigdubee,
The exact same thing happened to my 2010 MacBook Pro today. Restarting with the "option" key held down, I get only 2 of the 3 options you listed in disk utilities ("disk0" and a subfolder of "disk0" labeled "Mac OS x Base system".
Did you take your Macbook Pro to the Apple store? And were they able to fix it?

Macbook air flashing question mark

any solutions for flashing question mark on start up?

There are four general causes of this issue:
1. The computer's PRAM no longer contains a valid startup disk setting when there aren't any problems with the disk itself. This can be checked for by pressing the Option key and seeing if the drive appears.
2. The internal drive's directory structure has become damaged. This requires usage of an alternate bootable system to perform the repair.
3. Critical system files have been deleted. This requires usage of an alternate bootable system to reinstall them.
4. The internal drive has died or become unplugged. This is the most likely case if the computer took a sharp impact or there are unusual sounds coming from its location.
(90832)

Flashing question mark on startup Mac Pro 1,1

hi everybody, I have an issue with my Mac Pro 1,1. I bought this computer last week.
Occasionally, at the start up, the screen show a flashing question mark inside a folder. I know this is a HD problem.
Since it doesn't show the question mark every time, I don't know if I resolved my issue following the instruction provided by Apple (resetting PRAM).
Both times that I saw it is when I have unplugged and plugged the power cable of my Mac pro. Now is all ok, but I'm afraid...it is maybe a power supply problem? Or a logic board problem?
Sorry for my english!

The hatter wrote:
When you reset PRAM you 'cause' the flashing "?"
No, I've seen the flashing "?" only when I have unplugged the power cable. (Two times.)
System Preferences : control panel : Startup Disk - set the boot drive
Ok, I've done it yet.
Now the Mac starts up normally.
I only fear that the problem is the logic board or power supply.
Can I exclude this possibility?
I'm ready for a failure of the drive.
Thank you very much!

Flashing question mark on startup, no Macintosh HD on disk utility

I had to do a hard shutdown on my 2011 MacBook Pro, and when I went to restart it I got the gray screen with the flashing question mark folder deal. I restarted it and went through Internet recovery, but under disk utility there is no option for Macintosh HD, only disk0 and Mac OS X Base System.
Any fix to this?

Possibly:
Clean Install of Snow Leopard
     1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
         with your computer. Insert the disc into the optical drive and restart the computer.
         After the chime press and hold down the "C" key. Release the key when you see
         a small spinning gear appear below the dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, click on Options button
         and select GUID, click on OK, then set the format type to MacOS Extended
         (Journaled, if supported), then click on the Apply button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. After you finish Setup Assistant will complete the installation after which
         you will be running a fresh install of OS X. You can now begin the update process
         by opening Software Update and installing all recommended updates to bring your
         installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

White Macbook gives Flashing Question Mark on Startup

Similar Messages

Maybe you are looking for