White screen and constant beeping

I have a 2011 macbook pro.  This morning when I powered it on all I get is a white screen and constant beeping sound.  The beeping goes away after about 2 minutes.  Then there is a folder with a flashing ?.  Is this something I can take care of at home or do I need to take it in to an apple store?

I noted that nowhere in that article is beeping mentioned.
Instead of seeing the Finder or the login window after startup, your computer may stop responding and the display may only show a persistent gray screen (you may also see an Apple logo, spinning gear, spinning globe, prohibitory sign, or a folder with a flashing question mark on it). Note: The below steps may not apply if a blue screen appears during start up.

Similar Messages

  • Intel Imac stuck at white screen and 3 beeps sound continously....

    Intel Imac stuck at white screen and 3 beeps sound continously when power on. Pls help......

    Well Barry, as for the Ram, all this while are install by apple technician since very day i bought iMac on july 2008. Just wondering What's actually went wrong..
    Very first day I bought iMac, few days later, system cant even on. AppleCare Centre exchanged a new set of iMac.
    two weeks later, i notice several dead pixels appearing on screen, call to log a case with them, later on, they changed a new panel.
    After several months pass, been using happily with iMac... but since now, this problem occurs. So fastrating... My third time encounters problem with iMac. sign
    Any suggestion? If not, I guess i have to bring this bulky iMac to applecare centre again. sign

  • System stuck on white screen and beeping sounds

    Power button turns screen from black to white and computer starts making intermittent beeping sounds. Tried SMU reset, hard reset, disconnecting cables but the problem stays the same. Any other suggestions.

    I had a similar problem on my 24" iMac purchased Dec 07. It was OK from a cold boot, but would go to the white screen and 3 beeps on any reboot. If I held down the Option key I could select the only disk and it would boot OK. I tried detaching all external disks - no change, ran HW diagnostics, - showed no problems. Ran disk verify/repair from CD, no errors. System info showed no problems with POST or the DIMMs.
    I first re-seated both 1Gb DIMMs - no change.
    Swapped the DIMMs into opposite slots - no change.
    I removed one, fixed the problem.
    I put in the suspect one by itself - problem returned.
    This is original RAM that came with the system, trying to get the suspect DIMM replaced now, but system is OK for the moment on 1GB.

  • IPod has a white screen... beeps twice when I reset.

    Well, that was before I restored it.
    Now it's stuck on a gray screen and still won't respond. I called an iPod rep and they said it might be a pixel error? Dunno.
    Any suggestions on how to fix this or what I should do? Thanks in advance

    I have almost the exact same problem. The only difference is that whenever i plug my ipod in to charge(doesn't matter where, same thing happens with every charger), i get a white screen and two beeps. I tried reseting and i tried restoring but none of that worked. The computer says that the ipod is corrupt and sometimes when i plug the ipod into itunes it doesn't show up and the computer doesn't register the the fact that ipod is connected. Even though the ipod is charged, i can't even get to turn on. Im thinking about replacing it but i'm not sure. Please somebody i need help with my ipod!!!

  • TS1367 Hallo,I have an IMAC 21.5. which does not start.When i press the power button i hear only beep with an interval of 4-5 seconds.Some times when i take off the RAMS and put them again then get a white screen and shows that i have to insert a bootable

    Hallo ,I have an IMAC 21.5. which does not start.When i press the power button i hear only beep with an interval of 4-5 seconds.Some times when i take off the RAMS and put them again then get a white screen and shows that i have to insert a bootable device.Then i bought OSX mountainlion on line and wrote it on a DVD and tried with a USB key board to start the DVD.But does not work.Please help me to get this imac work.
    Thankyou in advance  for your help.
    Terrence

    Hey terremo,
    Thanks for the question. From the information you provided, it sounds like the iMac is successfully turning on, however video is not displayed. These symptoms can usually be isolated further by the troubleshooting steps in this article:
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/HT1573
    Thanks,
    Matt M.

  • My MacBook Pro 13 won't start has white screen and beeps

    I used my MacBook pro lastnight and worked fine. Tried to turn it on this morning and it won't start. Does sound like it is going to then before login screen shows ur goes to a solid white screen and beeps every 7 seconds. Need help school is about to start again.

    Check this out.
    I think you have bad RAM, so either you've recently put in new RAM, knocked some RAM loose from the socket (really hard to do), or the RAM went bad (maybe).
    You might need to see a real tech.
    Upon further review, I think your MBP has a serious problem.  You need to take it to an Apple Store for repair.  If you bought it within the last 12 months, you will be able to get warranty service, as long as you're not at fault. 

  • My ipod nano has a white screen and beeps twice, Can i fix it?

    I left my ipod in my pants and they went througth th washer and dryer, I put them in white rice for two days and it still has the white screen and beeps twice, Can i fix it?

    Hello Emmuhhlieee,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/ts3474
    Display shows a white screen
    Try putting the iPod into disk mode:
    Reset the device (press the Sleep and Volume Down buttons simultaneously until the display turns black—about eight seconds).
    When the display turns black, hold down the Volume Down and Volume Up buttons simultaneously until the device enters Disk mode.
    While the device is in disk mode, sync it to iTunes and try to restore.
    Best of luck,
    Mario

  • Ipod nano: white screen and beeping twice

    I have an ipod nano 4th or 5th generation. When I try to turn it on, it displays a white screen and beeps twice. I have tried the basic things: toggling the lock switch, holding down select and menu buttons simultaneously, doing that and then holding down the play and select simultaneously. Even restored it. Updated all of my itunes software. Still broken. What next?

    Hi
    It seems to be ok now... I had to go out and it ran out of battery, when I switched it back on it  appears to be fine.
    If it happens again (hoping that it doesn't!) and i do the reset.. will that remove all the music that's on there?
    Sorry for the ignorance
    Thank you for the answer

  • Constant white screen and inability to reset ipod nano

    Hi all,
    I just purchase my ipod nano from singapore and I realise that my ipod nano hangs often with a white screen and even after resetting. Can you pls advise me on how to avoid this problem?
    And I am now in Paris studying, does the warranty covers worldwide??
    Thank you.
    Regards(:

    Give the usual troubleshooting steps a try:
    http://www.apple.com/support/ipod/five_rs/nano5gen/
    If that does not work, let us know.
    i

  • How do I resolve an unresponsive white screen with a beeping sound in a pattern of three?

    How do I resolve an unresponsive white screen with a beeping sound in a pattern of 3?

    What iMac model and what Mac OSX version (iOS cannot run on Mac computers).

  • My iphone 5 screen has been cracked. Black Screen. Constant beeping.

    My iphone 5 screen has been cracked for a few weeks but worked fine. Yesterday the screen went black but Siri still worked. When I plugged it in to charge, it started beeping as if i were constantly unplugging it then plugging it back in. At first the screen would light up even though it was black but now the screen wont light up at all. I ordered a new screen to replace it but now I am thinking that it is more than the screen. I plugged it in to my computer and it doesn't recognize it at all. Use the same cord to plug it back in to the wall and it starts beeping again. Could the screen cause all of this or is it a bigger problem? Please help!

    Agree with the comments of FelipeV the crux of the matter is that mpeterson329 abused his phone.
    Also agree with the below comment:
    Peter GillespieSep 1, 2014 9:18 AM Re: My iphone 5 screen has been cracked. Black Screen. Constant beeping.
    in response to mpeterson329
    Have you dismantled the iPhone in any way yet ?
    <Edited By Host>

  • Hp pavilion g4 1104dx display white screen and caps lock blink twice

    Hi i recently used my hp laptop screen to test another laptop acer aspire 5517. After the test i reconnected back the cable only to power it on a white screen appeared with caps lock blink twice. I thought the problem might be screen shot so i decided to connect to external monitor but still no signal on external monitor even after pressing fn+f4. What might be the problem thanks.

    Hi there , Thank you for visiting the HP Support Forums and Welcome! This is a great site to get answers and ask questions. I understand you are having an issue with your Notebook. You had stated that you receive a White Screen and the Caps Lock are blinking twice. Please be very careful when it comes to blink patterns as sometimes there can be a pause between the blinking.   Before you start troubleshooting, please note remove any and all USB devices. Disconnect all non-essential devices, as these could cause some issues. Here is the first document I found called Performing a Hard Reset or Forced Reset. If that does not work, please follow Computer Does Not Start (Windows 8). The last document I have for you that may help is called Computer does not start and the LEDs blink or the computer beeps. Please follow these provided troubleshooting steps, re-post and let me know how everything went. Thank you! Have a great day!

  • Intel OS X 10.7 iMac has white screen and three-alarm sound, won't start up

    Intel OS X 10.7 iMac has white screen and three-alarm sound, won't start up

    The 3 beeps during start-up are telling you that the RAM is bad.
    If you can access the RAM modules, you may try taking them out and putting them back in, perhaps it's only bad contacts.
    If that doesn't help, you'll need new RAM module(s).

  • Help! When I select "Phone" it tries to open and gives me a white screen and closes. I cannot view my missed calls or voicemails.

    If anyone knows anything about this...
    When I select "Phone" on my home screen the iPhone attempts to open it, brings up a white screen and then will shut back down. I have 8 missed calls or voicemails yesterday and I couldn't check any of them. Does this happen to anyone else?
    Also, when I receive a call and I answer it does not give me the ability to end call or any of my options (sources, keypad,etc.) during the call.
    Basically, I can't do anything with my contacts, favorites, missed calls or voicemails.
    Can someone please help?

    I have tried that multiple times. I have also made sure that I have the latest updates. Would haveing 27,000+ contacts have anything to do with it?
    Sometimes it works and sometimes it doesn't

  • This is my first mac, it is a macbook pro. i restarted it but when it started back up i saw a white screen and then it prompted me to insert the reboot disk. anyone else have this problem?

    I recently bought a Macbook Pro, this is my first Mac. I restarted it, but when it started back there was a plain white screen and then it prompted me to insert the reboot disk. Has anyone else had this problem and is there a way to do this manually like with PC's?

    The new Mac's came with OS X Lion 10.7 and there are no boot disks.
    Since it's so new, take it back to the Apple Store and let them deal with it.
    If not you can hold Command and r (as in rotten) keys down and boot the computer.
    You'll be presented with a several options, including one to reinstall OS X Lion provided you have a Apple ID, which means you have to use Safari in there to set one up. To do that you need to set up a email account with Google or Yahoo. Once you get the ID, then you can download Lion and reinstall it.
    It's so stupid not having a copy of the OS on hand to perform your own repairs.
    Of course Apple will be happy to sell you a $69 Lion USB stick.
    Like I said, take it back to the store, and try to get your money back, that will force them to think about just giving you a replacement machine that works.
    Lion doesn't work really but it can be acceptable until the patches get released.

Maybe you are looking for

  • Can you get your money back from returning an apple product?

    Mind on my $Money$..

  • Plant field in MIGO in ECC 6.0

    Hi, When I goods receipt a purchase order in MIGO in SAP ECC 6.0 for a particular plant(e.g. 0010) and later on in the day I then goods receipt another another PO for a different plant (e.g. 0600) how come the Plant field still contains the 0010 plan

  • Initialization without data transfer

    Hi bw experts, when i am loading data to ods 0fiap_o06.actually i loadded selection wise data in same infopackage for full update .after that when i try load initialization without data transfer iam getting this error 1.Full updates already available

  • Trying to update LR, get a prompt for serial number

    I'm already a CC subscriber and when I updated LR to 5.3, I get a "serial number or try it" prompt. Did I go about the update the wrong way? I should just get all updates automatically, right?

  • Subject: QM : Unit of Mesure of Field Cant find in any table

    Dear All sap Gurus, I have one inspection lot , for that inspection lot no of characteristics & specification & result are maintained . the t-code is QE13 in that t-code i am maintained this things . in that t-code in specification column FC maintan