White screen, apple logo and spinning wheel on startup

I Have a MacBook Pro mid-2012 and suddenly it froze, so I tried shutting it down, but when I turned it on there was this grey screen at first with the apple logo and a spinning wheel. After a few times I shut it down and turned it on, the screen turned white, but the apple logo and the spinning wheel remained. I tried Safe Boot, reseting the NVRAM/PRAM and Internet Recovery. None of them worked. On internet recovery, the bar is stuck at the beginning and after an hour there is an error that says apple.com/support -5010f. Why is there an error on Internet Recovery and what can I do to fix my MacBook?

I hope you have a backup (preferably a bootable one).
Here’s a reference, read this first: Gray, Blue or White screen at boot, w/spinner/progress bar
You don’t mention booting to your recovery partition, you can try that.
There is also single user mode: (restart, hold down ⌘S until you see a black screen with white text) and repair your hard drive. Here's a reference with directions: Repair Your Hard Disk in Single User Mode | Everything Macintosh
If you have a bootable backup (like a clone that you made with Carbon Copy Cloner) you could try to boot from that and then use it to either
repair your usual boot drive
erase your usual boot drive and restore from the backup
If you have a bootable installer (like a thumb drive that you made with Diskmaker X (DiskMaker X (formerly Lion DiskMaker) then you could boot from that and see if you can repair your HD or erase and reinstall.
If you have a third party utility like Techtool Pro (Techtool Pro 7) that is on another partition of your drive or on a separate disk you could try to boot from that and see if you can repair your HD.
If none of that works then maybe your HD has a mechanical failure and needs to be replaced.

Similar Messages

Imac won't start beyond white screen apple logo and circle

Imac won't start beyond white screen, Apple logo and spinning circle

Follow the steps at > Mac OS X: Gray screen appears during startup

Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?

Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?
Unfortunately do not know the operating system since I never updated anything and I can't get in to it.
Thanks for your assistance.

If you want to preserve the data on the boot drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.

I cannot start my mac book. Apple logo and spinning wheel on gray screen. Tried pressing shift key on start up nothing happen. Tried shift command V screen is still stuck

I cannot start my mac book. Apple logo and spinning wheel on gray screen. Tried pressing shift key on start up nothing happen. Tried shift+command+V screen is still stuck

Reinstall OS X without erasing the drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
=======================================
Reinstall - Mavericks, Lion/Mountain Lion
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall Mountain Lion or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is
three times faster than wireless.

HT204347 Hi my serial number on bottom of my mac is W8*******66E when l try to try the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not

Hi my serial number on bottom of my mac is W8******66E when l try to turn the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not worked?
<Edited by Host>

What other solutions have you tried?
This may help you:
https://discussions.apple.com/docs/DOC-3353
Ciao.

Mac pro running OS 10.5.8 won't boot. Apple logo and spinning wheel shows then Apple logo turns into Forbidden signage while spinning wheel continue. It happenened right after I installed a firmware. Had to restart.Please help. What can I do?

Mac pro running OS 10.5.8 won't boot. Apple logo and spinning wheel shows then Apple logo turns into Forbidden signage while spinning wheel continue. It happenened right after I installed a firmware. Had to restart.Please help. What can I do?

Work through the suggestions in this article:
Mac OS X: Gray screen appears during startup

Please help me! MacBook Pro stuck on apple logo and spinning wheel

Hi I'm really desperate and need help! My MacBook just stopped loading and would stay on the gray screen with the apple logo and spinning wheel.
I have tried safe mode and it would load a little and stop and then the loading bar would be blank and it would stay like that forever!!
I also have tried doing the single user mode and when I type the fsck - fy it will do a couple more lines then it will say error like a hundred times :(
I did verbose mode and it would just give me stuff that I have no idea what it saying I left on verbose mode for like 5 hours and it would just give me lines of stuff I have no idea what it's saying!
I downloaded lion through apple store so I don't have the disk I only have my snow leopard disk
Please please someone tell me a solution it's my moms laptop and I don't want to get in trouble!

Reboot in recovery mode an possibly repair over the internet.
Command-R to the rescue.
Just hold down Command-R during startup and OS X Recovery springs into action. It lets you choose from common utilities: You can run Disk Utility to check or repair your hard drive, erase your hard drive and reinstall a fresh copy of OS X, or restore your Mac from a Time Machine backup. You can even use Safari to get help from Apple Support online. And if OS X Recovery encounters problems, it will automatically connect to Apple over the Internet.
http://support.apple.com/kb/HT4718

Start Up Issue-Gray Screen, Apple Logo And Cognition Wheel-Blue screen before start up at times but no longer starting up beyond gray screen and cognition wheel

Power button pressed.
Start up light okay
Chimes okay
Gray screen, apple logo and cognition wheel spinning and the loading bar underneath loading 1/10th of the way.
Loading bar doesnt load fully and then disappears.
Gray screen remains with apple logo and cognition wheel only.
No start up to desktop. Before start up to desk top which is not happening any more a blue screen appeared before the desktop appeared. When start up complete the ' Finder' had no responded and did not work' Multi coloured loading pointer continually turned. ' Network' could not be loaded in 'System Prefrences'.
Ive tried reading and following propts...Results NVRAM/PRAM - Logic board battery replacement. How much will this cost?
Hardware test - No problem found
Safe Boot - ' volume Machintosh HD could not be repaired.'
' Run time corruption detected on Machintosh HD device'
What do you suggest aside from taking it to a apple store?
Thanks Stephen

Lion or Snow Leopard? If Lion, boot into your Recovery partition (hold down the Command and R keys whilst booting) and use Disk Utility to verify and, if needed, repair the boot volume.
If Snow Leopard, use the installation disc and use Disk Utility in the same manner.
Clinton

Apple logo and spinning wheel after hard drive replacement and restore

Hi, need some help!
I replaced my hard drive at the weekend in a mid 2010 MacBook Pro with a Samsung/Seagate 1TB 2.5 inch 5400RPM SATA II Hard Disk Drive. The install of the hardware went fine, and the computer recognised it no problem. I went through the process of formatting which again went ok, then I moved on to the restore of the old image from my time machine.
After the 4 hours or so it said restore successful and a restart was required - after the restart I am presented with the apple logo and spinning wheel and can make no progress beyond this point.
I have tried 3 restores now - all of which were 'successful' and have the same issue. I have checked the disk using the repair tool and there are no recoded issues so I'm at a loss.
Can anyone help!!
Thanks in advance

Hey andrew1878,
Thanks for the question. I understand that you are experiencing issues with your MacBook not loading up past the Apple Logo and spinning gear. The following resource may provide a solution:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/TS2570
Thanks,
Matt M.

I did an auto software update on my iMac, which included a restart. When the machine restarted it's stuck with an Apple logo and spinning wheel. I've tried all of the key strokes that are supposed to work, but nothing has. Any suggestions? Thanks!

I did an auto software update on my iMac, which included a restart. When the machine restarted it's stuck with an Apple logo and spinning wheel. I've tried all of the key strokes that are supposed to work, but nothing has. Any suggestions?

Gray screen could be any number of things, bad third party at boot kext file, a bad Apple one, a bad install/upgrade of OS X, drive corruption etc.
Run through this list of fixes
Step by Step to fix your Mac

Macbook Pro Stuck at Apple Logo and Spinning Wheel

I Have ML. Just did the most recent update. There seemed to be a bundled group of updates. Once all was updated, my computer froze. I shutdown and restarted and it was stuck on the Apple Logo and spinning wheel. I have tried everything. Safe Mode, Command R, Command/Alt/R/P....it does nothing. Any advice out there?

Reinstalling Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

IMac is stuck on apple logo and spinning wheel

My wife did a software update and them it asked for a restart, she click restart but the computer got stuck in apple logo and spinning wheel. Won't go past that now. Just keeps spinning! Help for I know not what to do!!!! Please any idea?

An invalid node is an error DU cannot repair. If you don't mind spending $100 for Disk Warrior, then I suggest you buy it because it can fix the error. Otherwise, do as the warning says. Backup your files. You will then have to erase the drive and reinstall. The procedure is:
Install or Reinstall Lion/Mountain Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
      left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
        the Security button and set the Zero Data option to one-pass. Click on
      the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion/Mountain Lion and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.

Gray screen, apple logo and spinning gear hang at start up

after a lengthy round of "bejeweled", i let my imac fall into screen saver mode. when i tried to log back in, i tapped the mouse and the imac flashed as it does when actuated outside a dialogue without clicking the okay button, and immediately returned to screen saver. i then manually shut down and restarted to the gray screen, apple logo and spinning gear hang. i then inserted the leopard install dvd, manually shut down and restarted pressing the option key and selected the install disc. it booted as usual. i selected the language preferred, used the utility drop down menu and selected DU, then selected the hard drive and verify permissions to reveal a pop up "Error: The underlying task reported failure on exit. Permissions verification complete." i immediately selected repair disc, and breathed a sigh of relief with the notification "appears to be ok". then utilities/start up disc/macintosh hd/restart. still get the hang. i have repeated this process several times, also resetting the PRAM as well to the infinite hang. as a matter of fact, the gear has been spinning the entire time creating this post. needless to say, i am truly at a loss. SOS!!!!!!! Please!!!!! SEND LAWYERS, GUNS AND MONEY!!!!

i have perused some of the threads posted per this topic and decided to attempt an "archive and install." i also have a 620gig acomdata external drive with close to a carbon copy of my internal. a few short minutes into the install, the imac reveals a pop up stating it cannot install some files on the hard drive, contact the software manufacturer or restart and try to install again. the internal drive is a 160gig with only about 60gigs of room, so i tried to archive and install to the acomdata instead as it has 180 gig of free space. i get the exact same dialogue once again. restart and a third attempt only archive and install will not highlight, only first time and/or erase and install. further, start up disc shows only the install disc and network as choices. so i attempt first time install on both drives and get the same pop up message again. DU recognizes both drives although verify/repair permissions does not highlight, but not start up disc.
i'm trying not to become frantic, but my patience is threadbare. i am in desperate need of sound advice as to what i need to do.
thanks again in advance,
bradley

My macbook wont reboot apple logo and spinning wheel thats it.

I watched youtube videos and tried command r and now it keeps popping up you need to restart your computer. Everytime I restart it, it pops back up! HELP!!

Apple logo and spinning wheel is different than the need to restart your computer message.
See this Apple note on the spinning wheel at boot. If you are running OS X 10.7 or later, then rebooting with the command and r keys will get you into recovery mode, where you can use Disk Utility to repair the hard drive.
FYI, the need to restart your computer message in multiple languages is called a kernel panic, which is usually, but not always, caused by a hardware issue. If you have OS X 10.7 or later, you should be able to run the Apple hardware test. Prior to that, you need the disks that came with the system to run it. If you can run it, run the extended test when prompted, which can take over an hour to run.

MacBook pro 15" 2008 freezes at apple logo and spinning wheel

Have a MacBook pro early 2008 have installed lion but recently started to have problems. Started to freeze a lot so I would restart and most of the time it would work untill it froze again , now it's got worst every time I restart my Mac it won't go past apple logo and spinning wheel just freezes have been trying and trying but same thing freezes. Tried to start in save mode but no still freezes
Please has anyone got any suggestions thanks

The startup disk may need repairing.
Use Lion Recovery
Not enough free space on the startup disk can cause the system to freeze.
Right or control click the MacintoshHD icon. Click Get Info. In the Get Info window you will see Capacity and Available. Make sure there's a minimum of 15% free disk space.

White screen, apple logo and spinning wheel on startup

Similar Messages

Maybe you are looking for