White tint issue

Hi all, Yesterday I was using the phone before going to sleep and I have noticed a white tint on the screen. Didnt do anything about it but this morning I have made the screen test and when the screen is black its totally noticable. I am just wondering if anyone else has this issue and what I should do. I have brought this phone 20 days ago on the 6th. Thanks,Kamil

@kamil1308 Did you remove or damage the screen protector that came with the Z3+? My Z3+ came with a screen protector out of the box.

Similar Messages

White screen issue on Compag

My Compaq is currently displaying only a white screen. The laptop boots up fine and displays fine on an external monitor.
I have taken it apart and reseated the connectors on both the screen and the motherboard with no effect. So I am sure it's not a loose connection.
Before I go and splash out on a new replacement screen, is this an issue that is usually seen when the screen itself is at fault. Could it be the cable? or the connection on the motherboard itself. Is there a way to be certain?
I don't want to buy a new screen and find it's not at fault.
Many thanks!

Hello, @Skyfox
Welcome to the HP Forums.
I see that you have a white screen issue with the notebook. I will try to assist you.
With the steps you've taken and the fact it works correctly with an external, leaves only the display screen as the possible cause. That being said, there is no 100% way to know that it is not a cable causing the issue.
Typical steps for this issue:
Restart notebook
Hard reset notebook
Test with external monitor
Reconnect LCD cables and check all other display cables
Have notebook serviced.
You're at the point of service. This really limits the options, and a display replacement may not correct the issue.
I hope this adds any insight to the choice you need to make next.
Thank you for posting on the HP Forums.
I worked on behalf of HP.

Yellow Tint issue

I know this isn't the first thread on the yellow tint issue, but I've had some strange experiences that need to be addressed.
http://lh5.ggpht.com/TLglqt0-RdM/SVlOWBinyjI/AAAAAAAAArM/ZjMXtH60po/s640/P10306192.JPG
See, when I first started using this iPhone (bought it from a friend) it seemed fine. Then moments upon boot, I started noticing this feint flickering, each time it flickered (as it still does) the screen would be "brighter" but not by the normal brightness settings... and it had a yellow tint to it compared side-by-side of my normal other iPhone.
So I explored more, and since they have both already been opened before, I reopened them and tested a theory. If this iPhone has a yellow screen, maybe the screen needs replacing. I take them both apart, swap the screens, and voila!...... still Yellow?! Hmm, so the screens not the problem...
Now I'm even more puzzled, because I'll just be staring at the flickering, so faintly but distinguishable. And if I catch the right moment for a split second it flashes totally normal, then back... its so brief, but does this mean theres software fix potential in this?
I know nothing about what to do next. Apple, the Community, someone point me in the right direction. Obviously the reason I seek help is because these iPhones have been opened before, but only to switch screens and never deeper. Does this honestly count as a warrant breach or can this be considered justifiable to replace a cracked screen on your own?
Thanks for your help!

You are absolutely right there is a difference and I have not read the small print. I'd put money on it tho. That said you may be lucky in that they'll help you even if you have defaced it.
You should find what you need [here|http://manuals.info.apple.com/enUS/iPhone_3G_Important_Product_InformationGuide.pdf].
Here's a snippet from it;
*Repairing or Modifying iPhone*
*Never attempt to repair or modify iPhone yourself. Disassembling iPhone,*
*including the removal of external screws, may cause damage that is not covered*
*under the warranty. iPhone does not contain any user-serviceable parts, except*
*for the SIM card and SIM tray. Service should only be provided by an authorized*
*service provider.*
Message was edited by: gumsie

Ongoing White Balance issue

In a video I just shot there is a slight shift in exposure in the image - just when my subject moves a couple times. It is shot with a white background and she is wearing black. I think this is a white balance issue. Which filters or fixes are best for this? I have tried a few filters and they mostly do it but you can still see the couple times my subject moves and the light/exposure changes. I realize that I need to film it better, but can it be fixed. Thanks for any insights.

Search for "flicker fixer premiere pro". I don't use any of them so you will have to see what works best for you.
You can use the Fast Color corrector in PP to change exposure. You will have to make key frames. If you're not sure how to use key frames and how to use the Fast Color corrector it's time to open the manual.

Video Green Tint Issue?

I discovered a green tinted screen after waking my HP Mini from sleep mode. The only way I was able to resolve this was by restarting.
I have 4GB of memory, but my SSD is running out of space. It's down to 1.3MB. I'm just wondering if that could have been the reason for the green tint issue.

Hello @MaxInMusicCity,
I have read your post on how your desktop computer is displaying a green tint, and I would be happy to assist you!
To further diagnose this issue, I recommend following the steps in this document on How to Turn off Hardware Acceleration. I also suggest updating your Java and Adobe Flash Player software.
If the issue perssits, please follow the steps below to restore the power management settings for your computer:
Step 1. Click the Start button
Step 2. In the search box, type "Command Prompt"
Step 3. Right-click Command Prompt
Step 4. Click Run as administrator
Step 5. At the command prompt, type powercfg /restoredefaultschemes and press Enter
reference: http://superuser.com/questions/669571/windows-8-1-64-bit-power-schemes-gone
If the green tint still appears after waking up your computer from sleep mode, I recommend following this document on Troubleshooting Sleep and Hibernate Issues (Windows 8). This should help to wake your computer from sleep mode without displaying a green screen.
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Creative Zen X-fi (with lan) white screen issues

?Hello everyone, So I've been having my zen x-fi for a few months and it has been working excellently...until yesterday when it suddently (after what might have been a lightly hit, I had it in my front pocket and bumped in lightly into some object)...well suddently the screen went white but kind of still something black there (see photo below) <a rel="nofollow" target="_blank" href="http://img40.imageshack.us/img40/666/dscf2249redigerad.jpg"]http://img40.imageshack.us/img40/666/dscf2249redigerad.jpg[/url] I have been looking into troubleshooting about this particular issue, but what is suggested there under the white screen-issue is to reset and update firmware, something I did already first thing after it happened. The thing is that other than the screen being a quaking mess, it seems to otherwise be in working condition, because when I turn it on and push the play button music will still play as before. it's just the screen that is the problem. Any ideas? Best wishes, Babba

Hello there, thank you for your welcome. That is sad info about my music player though, I liked it so much while it was still working. unfortunately im not within the warrant period so I will have to invest in a new one. thank you for your help though. I will look into which creative player is the best one within my price range

Iphone4 white antenna issues

I bought iphone4 white, antenna issues are still there and i was advised to buy case. Is it very common problem

http://support.apple.com/kb/HT4389
Already been there/done that before coming here.
The issue, if the iphone4 is held in the palm, the reception drops to nothing.
Out of palm, back to 4 lines 3G. In palm, nothing. Out of palm, 3G.
And so on and so on...
Assuming the antenna is the metal strip along the edge,
holding the phone is affecting the antenna/reception.
As far as apple express lane support...
Had them call me (land line), apple express rep took phone info, took my tele # in case we were disconnected, put me on hold to look up some guidance, 5 minutes later while on hold connection lost
followed by a busy signal.
Hung-up, waited for a callback (i.e. in case we were disconnected), nothing...
No callback. No return call. And they had my #.
So I'll wait and try monday when possibly better informed techs are on call (hopefully).
Or wait for more customers of this new "white" iphone4 to discover the issue,
and take the rant national, as was the case with the black iphone4.
Or maybe I'll just take advantage of AT&T's 30-day return policy and switch to the samsung android.
We will see...

U330 Bios v.68? Anyone still have this available? Still having white bar issues.

Requesting u330 bios update v.68 beta.
Had put away the u330 into storage last year thinking it was unfixable due to a broken LCD. Learned through reading through the massive discussion, http://forums.lenovo.com/t5/Windows-7-Discussion/U330-Windows-7-Drivers-Problem-amp-Solutions/td-p/1... , it was fixable bios/driver issue concerning the graphics cards. The link for the v68 bios update no longer exists on the thread.
What I did: Per instructions, Flashed with v.67 (latest from Lenovo website). Then fresh install of Windows 64 and updated everything through Windows.
This fixed the power issue and most of the white bar issue. There are a few lines that pop up sometimes and the bar sometimes flashes on and off depending on the graphics use. For example, when I wash something on youtube or hulu.
New issue: Doesn't detect the discrete ATI card. Only the integrated Intel card is shown on device driver and the bios doesn't allow me to enable vtx/discrete card or whatever. ATI is nowhere to be detected. Tried installing ati and the new amd catalyst drivers and neither can detect the driver either.
Reading through the thread indicated that the bios 68 beta would solve my the switching issue and the remaining white bar issues. So I gotta ask. Does anyone have it available????

I can't imagine that it is really a hardware problem... It only happens for me when there is some kind of moving graphics on the screen and it isn't at the front of the windows or switching between windows. And it all kind of depends on whether I'm running programs with moving graphics or am at websites with graphics/video. For example, if I go to the Hulu homepage (which has a changing banner) and then simultaneously open the start menu or a folder in windows, the flashing white bar appears. In this case, the moving graphics is now "behind" the start menu or the window. But if I then click on the maximized homepage again, the flashing white bar disappears. Interestingly, this seems to happen only when I use Google Chrome as my browser. I can also make it reliably happen by just going to the desktop. Pressing on the bottom of the screen doesn't help me at all.
Given that this problem started for many people around the same time, which, to me, suggests that maybe there was a update to the graphics card or windows update that led to some kind of funky incompatibility.
Do other people have "symptoms" that are as specific as mine? Maybe we have multiple problems here ...

Firmware 1.1 White Noise Issue

I upgraded to 1.1 from 1.03 and do not have the white noise issue at all. Have 2,000 songs and bunch of videos and about 100 pics. Had 0 problems, iTunes and iPod update all went 100% smooth.
Saw some bad reports, just wanted to let those thinking of upgrading that the problems mentioned do not occur 100% of the time.
I also have no unusual noises and never have had the battery draining problem.
160Gb Classic

It is totally random, there is no pattern to it. It was the day after I updated to 1.1 before the hissing started on my player. It hasn't happened so far today but it may happen later on tonight. I had no issue with the update and all my music, photos and videos remained intact but the hiss and thumping noise you get when you remove the earphones is a real bummer and a total let-down with this new firmware. Check to see if you get the loud noise when you remove your earphones; if you are you may very well get the hissing. It's certainly happening to the majority.
PAUL
Message was edited by: vocrobot

Flash builder white screen issue

Hi All,
I have create one normal project.There is no issue but after run that project i got one issue that is White screen Issue.......i have updated flash player but cant fint that problem ....any one Tel me the reason.
Thanks
Prabu.a

After further investigation, we found out that we were defining a few of our namespace by referencing directly the packages of our custom component instead of creating a clean namespace as recommended by the flex documentation. Using the package definition works just fine when it is local but our component were located in a swc library.
We were doing this :
xmlns:foo="com.mCompany.controls.foo*"
instead of generating an xml manifest and basing our namespace on it
xmlns:foo="http://com.myCompany.controls/foo"
We think that flash builder was slowing down because each and every time we were loading up an mxml it had to rescan the said package.

White balance issues after ProKit Update 5.1

After the new ProKit 5.1 update I get a new reprocess block. When I reprocess the image the white balance gets messed up. The Tint sliders go to 50. The white balance presets are all off too. Is anyone else having issue?

This is frustrating me too. Some things I've discovered:
Reprocessing photos tagged with the 1.0 to 1.1 which required reprocessing caused most of the issues. The auto-converted photos would go from 5200K temp, -1 tint or similar to having a wierd tint. However, using a tint around 90 (off the range the tint slider can be adjusted to. Similarly, using the dropper to select a whitepoint results in these out of range tints. However, the tint looked OK, it's just out of the range you can slide it to.
I tried the deletion of the Raw decode plist and that didn't fix things.
Also of note, I have a selection of images with each of my camera's whitepoint settings (a Canon 30d as it happens). If I reprocess each, select the whitepoint brick to enable it and press reset, I get back the whitepoint which was interpretted from the RAW (and hence the cameras whitepoint setting). These also leap from say ~5200K daylight -1 tint (if I recall correctly) to having offscale tints. This suggests there's a new range at play for RAW 3?
Incredibly frustrating. If anyone has any reasonable fixes, I'd love to hear about them, or preferably could we have an update from Apple which resolves the issue.
I understand that reprocessing can cause small shifts, but my photos which have not been heavily adjusted look totally wrong when reprocessed. For now I will not be reprocessing anything until there's a fix.
Also of note, it looks like way back I locked my default raw processor to 1.0 or 1.1. That may have caused issues. I have since reset the camera defaults to the reset RAW processing defaults for 3. I'll try importing some stuff from camera tonight and see what it does.

White Balance Issues

Hello,
I have noticed this for a couple of weeks now. The display on my 2012 MacBook Pro (non-retina) will switch white balance for a second and then flip back to the normal colors. When it does this you can notice a distinct blue-ish tint to the colors on the screen. The first few times it occurred it lasted for only a second and then would be normal. But today it has occurred twice now; the first lasted for a few minutes and the second hasn't switched back. The current OS of my macbook is Yosemite.
I tried going into the display options under system preferences but all the options still have the blue-ish tint to them. Any one else have this problem? I spilled coffee on my mac last week but this was a thing before that happened. I'm really hoping that it's not a sign of the screen dying.
Thanks for any help.
Travis

This is frustrating me too. Some things I've discovered:
Reprocessing photos tagged with the 1.0 to 1.1 which required reprocessing caused most of the issues. The auto-converted photos would go from 5200K temp, -1 tint or similar to having a wierd tint. However, using a tint around 90 (off the range the tint slider can be adjusted to. Similarly, using the dropper to select a whitepoint results in these out of range tints. However, the tint looked OK, it's just out of the range you can slide it to.
I tried the deletion of the Raw decode plist and that didn't fix things.
Also of note, I have a selection of images with each of my camera's whitepoint settings (a Canon 30d as it happens). If I reprocess each, select the whitepoint brick to enable it and press reset, I get back the whitepoint which was interpretted from the RAW (and hence the cameras whitepoint setting). These also leap from say ~5200K daylight -1 tint (if I recall correctly) to having offscale tints. This suggests there's a new range at play for RAW 3?
Incredibly frustrating. If anyone has any reasonable fixes, I'd love to hear about them, or preferably could we have an update from Apple which resolves the issue.
I understand that reprocessing can cause small shifts, but my photos which have not been heavily adjusted look totally wrong when reprocessed. For now I will not be reprocessing anything until there's a fix.
Also of note, it looks like way back I locked my default raw processor to 1.0 or 1.1. That may have caused issues. I have since reset the camera defaults to the reset RAW processing defaults for 3. I'll try importing some stuff from camera tonight and see what it does.

2006 White Macbook Issues?

I have a late 2006 white macbook with a 2.0 ghz core 2 duo (Lion), and I also have a mid 2006 white macbook with a 1.83ghz core duo processor (Snow Leopard). I recently bought a 3rd party battery for the late 06 version. The battery had good reviews but once I installed it into the macbook the battery indicator icon said "service battery" and battery life went rapidly downwards. Out of curiosity I put the defective battery in the 1.83ghz macbook and everything appeared fine. I got 4.5-5 hrs of battery life with no "service battery" message. What could be causing that?
Also The 2.0ghz one has been having heat issues since I bought it (~1.5 months ago). Not overheating issues, just very loud fans and a very warm case. I don't do very intensive things on either laptop either. Just a single tab of web browsing. The 1.83ghz Macbook runs whisper quiet and is considerably cooler on the outer case. I cleaned both of dust recently and I re-applied thermal paste on both also. Could the 2 issues be correlated somehow? How can i fix them?
Thanks,
camtechguy98

Well first try what Mike suggests:
"Try resetting the SMC Intel-based Macs: Resetting the System Management Controller (SMC)"
If that doesn't work refer to my post about cleaning the fans above your post. Any decent service tech will be able to do that.
Apple store for sure.
This article addresses most of the issues I've seen:
http://apple.stackexchange.com/questions/120177/macbook-fans-are-running-high-ev en-under-normal-load
"get the fan serviced before I decide to ditch it."
Oh no! Please don't ditch it. I repair Macs and donate them. If it comes to that email me first.

Mac Mini Server Boot Camp Windows 8.1 White Screen Issue

Hello Apple Peeps!
I have a Mac Mini Server 2012 which I have had for around 6 months. I use it quite a lot mainly for Music Production on the OS X side and Graphic Design on the Windows side.
I recently decided to factory restore it as I wanted to spring clean it and reorganise the way some of my apps were installed. The way I had it set up was it was running OS X on one SSD and Windows 8.1 (installed using Boot Camp) on the other SSD. The way I went about the factory restore was I first used disk utility to erase/format the Windows SSD to Mac OS Extended (Journaled) and then went about the factory restore of OS X onto the other SSD as normal (following instructions from the Apple website).
The issue I am having now is that my newly installed Windows 8.1 (used solely on a single SSD) is hanging on a white screen for quite a long time before the Windows splash screen shows up, where before when I would boot or restart into Windows there was no white screen and it would go straight into the Windows splash screen and load to the desktop very quickly.
So my question is...
Why do I get this prolonged white screen before the Windows 8.1 splash screen appears? How can I get rid of it? It was certainly not present on my previous installation. Can anyone advise me what the computer is doing during this time so that I can do some further research into a solution.
What I have tried already....
1) PRAM & SMC reset.
2) Setting the startup disk to Boot Camp in both OS X and Windows 8.1.
3) Reinstalling Windows 8.1 through Boot Camp.
MAC MINI SERVER (LATE 2012), 2.6GHZ QUAD CORE I7, 16GB RAM, 2 x 256GB SSD, OS X 10.10.2, Windows 8.1 (Retail), Boot Camp Assistant (5.1.3), Covered By AppleCare.
I would really appreciate some help with this ;-)

I have right clicked on each SSD in Device Manager and selected the option 'Properties' from the drop down menu, which brings me to this window...
I'm not sure where I can find Device Attributes, I have clicked on each of the tabs in the window above, as far as I can see none of them mention AHCI enabled or anything similar. Thanks for all of your responses by the way...much appreciated!

Print Booklet with White Lines Issue

I have searched low and high on this forum and the internet for a solution, with no luck so far. I'm hoping that you InDesign gurus can help!
Whenever I use the 'Print Booklet' feature to generate a booklet from my InDesign CS5 brochure, the output has thin white lines in various areas that should NOT be there. The lines mostly show up in areas where I am using transparent PNG files, but there are no effects on the layers for these images.
This is an odd problem because:
In the original source while viewing it there are no lines
I can print to high resolution PDF using the standard print features and everything is 100% perfect, no lines
I can export each page as a high resolution JPG and everything is 100% perfect, no lines
The lines ONLY appear when I use the "Print Booklet" function. I have tried many things that have not worked:
Changing virtually every setting in Print Booklet to something else, lines are still there
Printing to a PDF directly from 'print booklet' with many different settings, lines still there
Printing to a PS file from 'print booklet', lines still there
Printing to an XPS file from 'print booklet', lines still there
I've put up an example showing you two different outputs. The one on the left is a regular JPG export, the one on the right is the Print Booklet export. Click on the images to see a larger example:
http://www.seenbest-web-design.com/techclub/?p=1282
I've seen other people post about this problem elsewhere going as far back as CS3, but have never found a cause or a way to fix this. Some people have said 'it's just a rendering issue in Adobe Reader, and the lines will not actually appear when you have it printed'. However, when I go to print from my PDF file to my printer the lines are there in the output. They are also there when I print to a XPS document and view the image on the screen.
Any ideas?

It's a transparency flattening artifact called Stitiching and basically, becasue youare printing to PDF you're up the creek. It only happens when transparency is flattened, but printing to PDF is a distiller function, and distiller doesn't support live transparency.
The best way around this, I think, would probably be to use an imposition script to impose a copy of the file, then export spreads from that using Acrobat 5 or higher compatibility, or, if you need to do this a lot, look into a PDF imposing plugin -- Quite Imposing gets good reviews here.
If you want to go withteh script, may favorite is Dave Saunders BuildBooklet javascript (http://pdsassoc.com/downloads/Buildbooklet.zip) but it has some limitations, no creep, 2-up saddle stitich only, and no objects crossing a spine. Slightly more sophisticated is his MakeBooklet script (Dave's CS3 Booklet Script) but it is still a lot less versatile than an impostion plugin.

White tint issue

Similar Messages

Maybe you are looking for