Who DOESN'T Have serious issues with K8T Neo-FIS2R

Kind of a stupid question since this is a support forum but im sure some of you are out there...

Quote
Originally posted by zerox_no1
Quote
Originally posted by scottg26
Quote
Originally posted by zerox_no1
Im not having any problems. Im happy becasue im running athlon64 3200+ @ 2.2Ghz using stock cooling with a cpu temp of 42'C idle without problems.
how do you do this???
and no, i don't doubt MSI, i've had 3 MSI boards, this will be my 4th
I use corecenter its as easy as that. :D
you mean dynamic overclocking?
who does use dynamic overclocking?
and is corecentre just like fuzzy logic?

Similar Messages

Booting "issues" with K8T Neo-FIS2R

Well hello everyone. First of all I want to say that my English isn't completely error-free and my problem might seem awkward because of my ways of expression.
I also want to say that i've read alot of threads and searched the forum for my problem.
For a couple of days ago I got all my parts for building my 64bit-system and I build her up. To my suprise it booted, with almost no errors. Although I could install Windows XP and use it completely, everytime I boot it (under the booting sequence) it says "Bios is not installed", although I can enter bios simply (like everyone else) just pushing the DEL-button.
But this isn't the only problem. When I enter PC Health Status it says that the cpu is running at whooping 62-65 degrees. When i have my hand around the cpu-cooler it doesn't even feel warm so I think it has something to do with my BIOS-version that i am running now (Yes, I've read that in much more threads)
Also I have problems using the Cool'n'Quiet technology. I have it supported in the BIOS and activated it although it will not work (maybe it has something to do with the bios?) With this i mean that i will not go underclocked (It's allways 2.2 GHz)
My final problem is that it sometimes takes the system 2 minutes to boot sometimes, it happend after i flashed the bios to 1.7 from 1.0
Under these circumstances I've used 1.0 AND 1.7 BIOS-versions.
I've never overclocked the computer either.
What could be wrong?
I'm using 3200+ 2.2GHz Athlon 64 cpu.
K8T Neo-FIS2R
Radeon 9800pro
Seagate 7200.7 200GB drive.
380W Antec PSU.

Quote
Originally posted by $post[username]
I've tested notebook, minial power savings and battery. C'n'q still doesn't seem to work. Yes i've enabled it in bios. I downloaded the AMD Athlon™ 64 Processor Driver for Windows XP, Version (zip) 1.1.0.14 -
Yesterday my CnQ began to work fine. I've done the same as you:
1- Enable CnQ Bios option
2- Install the AMD athlon64 driver for XP
3- Set "minimal power savings" at windows xp energy options
I have installed the CoreCenter 1.6.8.0 (is the last version) utility, and I've set enable the CnQ in this application. You'll can see that the CPU velocity change "on demmand" and the CPU fan too.
Of course, I've the last VIA 4in1 drivers, 1.7 Bios ver. etc
My temp & MHz values are:
~40ºC ~ 800 MHz idle
~50ºC ~ 2000 MHz playing or that kind of stuff
Note that the PC case is open, because the PC is under my table and there is no good ventilation.

Help! XP install problems with K8T Neo-FIS2R

The other day I put together a new system for a friend. I got the system to POST properly, the diagnostic lights on the D bracket are fine, and I can edit the BIOS, and the BIOS sees all the drives properly.
However, installing XP Pro has been impossible. I set the system to boot first to the CD, then to the hard drive (from the BIOS). After booting to the CD, I never see the message I am used to seeing ("Press any key to boot from CD...) when booting from the XP Pro install disk. The system thinks about things for a long time with a blank screen, then later it finally begins to do the install. Things appear normal at this point as in any other time I have installed XP Pro. I reformat the hard drive to start clean and then the XP install files are copied over. I get the standard message that the system will reboot and this is where things get flaky. The system reboots, but I never get the message once again on whether or not to boot from the CD. So after a while the system tries to install XP once again (it would repeat this process forever....trust me). I've popped the CD out right after the system reboots so it will try to go to the hard drive. I just get some kind of boot failure message and to insert the bootable media or whatever. I've even gone into the BIOS right after the reboot to switch the BIOS loading to try and load the hard drive first. This still doesn't give me the desired results.
This is by far the weirdest thing I've ever experienced when doing an install. I've installed XP Pro on at least 15-20 desktops/laptops of different configs and never ran into this before.
The BIOS settings are stock. I didn't see anything in there that was really needed tweaking or that hadn't "set itself". I haven't messed with the SATA or RAID stuff since it's not really necessary in this situation.
Here are the system specs:
--Antec 430 True Power PSU
--K8T Neo-FIS2R mobo
--AMD 3000+ 64 bit CPU
--40GB Maxtor HD (master on IDE1)
--Lite-On DVD-ROM drive (slave on IDE1)
--80GB Western Digital (8MB buffer) (master on IDE2)
--Sony DRU510A DVD-RW (slave on IDE2)
--(2) Kingmax 184 Pin 512MB DDR PC-3200 Model# MPXC22D-38
--ATI 9800 Pro
--3.5 Floppy
All the components except the mobo, CPU, and memory are from another AMD system that was running fine. No problems with any of the HD's or the optical drives. All new components were purchased from newegg.
I thought that maybe I had a problem with the jumpering of the drives so I messed with those in about every possible combination. I took IDE2 completely out of the system and just tried to get it running with the 40GB Maxtor and the Lite-On drive. I tried about every master/slave/cable select combination but nothing was working. In certain combinations the BIOS recognized everything as I intended. I've pulled everything off that doesn't need to be connected. Keyboard, monitor, and internal components are the only things connected.
I don't consider myself to be a guru at this business, but I can get through most things with enough trial and error. This really has me stumped.
Any help is certainly appreciated.
Thanks,
Heath

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Download the drivers from MSI again, and when you copy the contents of the XP folder to floppy ADD the file txtsetup.oem from the directory above that folder. Worked for me..!
Ian

6600GT not working with K8T neo-FIS2R

I recently returned a K8T NEO-FIS2R MB for repair. The problem was that the PS/2 and USB ports were broken. However the MB has been returned and the PS/2 and USB ports work fine. I posted about this several months ago.
Now the AGP port seems to be broken (not the actual slot). I have tried a 6800 Ultra and a 6600 GT (AGP version) GFX card in this slot. Both cards fail at the driver installation point. I have tried driver versions 66.93, 67.02 and 67.03. I also tried 3 versions of the via drivers 451, 453 and 455. Even tried XP with SP1 and SP2. The PC will sometimes BSOD, reset, won't boot into windows. The drivers sometimes install then other times they won't, etc. The problems only seem to be with the drivers for the GFX cards.
The 6600 GT works as I have tried it in another MB without any problems.
I know the memory works fine as I used memtest86+ for a couple of hours on the default settings without any errors and it works in another PC.
The spec of the PC is:
XP pro
K8T NEO-FIS2R MB
512MB corsair XMS at 2.5-3-7-3
XFX 6600GT
40gig HDD
FDD
Plextor CD writer
DVD Rom
PSU is a Q-tec 550W
I know Q-tec PSUs are not up to much from what I have read elsewhere in this forum, but I have had it running in a similar system with the 6800 Ultra installed without any trouble (even with the above MB before it went faulty). I have also tried a 400W PSU, that came with the case. The Voltages on the 12V line are between 12.00 and 12.03 when using the Q-tec PSU.
Has any body else had these problems with the 6600GT in the mentioned MB.
Also, how can I check the serial number on the MB with the label on the box, as this MB that was returned to me looks to “clean” to be the one I sent away for repair.
Thanks for any help

Hey, I'm glad to see a post on the new Gforce 6600GT AGP card. I just recently put together a brand new system (see my sig for specs). System runs great. The only thing I wanted to do was replace the video card, and after a great deal of anxiety I decided the Geforce 6600GT AGP was the best bang for the buck.
Well I got home, installed the card and never get passed the bios screen. (shows your processor, memory, memory siz), the screen u hit DEL to go into the bios.
The system doens't lock up, NUM LOCK can still be turned on and off, and CAPS can be turned of and on... but thats it. Just sits on that screen. I can't go into the bios either.
what settings do I need to do prior to isntalling this card to get it to work.
Let me know if you all need anymore details to help me out.
oh, I did reset my frequency to 10x200 (which is what I think the 3000+ is supposed to be at).

High frequency sound with K8T Neo-FIS2R

Hello!
I have the MSI k8t neo-fis2r mainboard with bios v 1.6 and sometimes it makes a horrible high frequency sound and I cant figure out why.
My system are:
amd 64 3000 cpu and
Corsair Value S PC3200 DDR-DIMM 512MB Unbuffered, Non-parity, 64Megx64, CL2.5
My other components does not cause the sound (that I have found out by testing).
I wonder if the ram causes the sound? Can you please help me. The sound is so bad that I cant use my computer. It only appers during heavy system load, and not in windows. It has nothing to do with my video card (because I have tried with several different cards). My bios settings are default values + cool and quit enabled. I have the core center installed so the progam controls the cpu fan.
I really hope someone can help me.

The sound does not come from the speaker and I dont think it comes fom the cpu fan either. I think it comes from the motherboard, ram or the cpu. When I dont use my mouse it is quit but when I clik it makes this sound. Can it be that I have to set all values in bios for ram etc. manually instead of automatic?
When it comes to other electrical sources I have a TV standing 0.5 meter from the computer. Could thins cause the problem? I did not have the problem with my old motherboard which was a MSI K7T Turbo2.
The sound usually appers when I am benchamarking my system. For example 3dmark 2004. Because of this I thougt there was a problem wiht my vga card but after a changed to a new one...the situation was just the same.

Is there anyone who doesn't have any problem with Z3 ?

I'm thinking to buy this phone, so I want to know is there anyone who has no problems with it, because in this and other forums, I find a lot of discouraged people who have a wide variety of problems.
Thanks a lot

uliwooly wrote:
Think about it, this is a Support forum. users who have issues come looking for help, it doesn't mean that the majority have issues.
I understand what you're saying, but this is my dilemma:
I currently have sony Xperia Z1 compact which is full of small problems.
-back panel rattle when I touch it near camera lens
-a big gap between the panels and the frame
-camera freeze and need to restart the phone very often
-calendar widget does not eject notification and birthdays...
I was looking for a solution to these problems on the forum for the Z1 compact, but so far I have not solved a single.
Such problems I have never had on my samsung phones. Still, I'm determined to buy a Z3 because of the design and premium materials, but if I compare it with My Z1 Compact, I'm a little scared.

Dear All, Since Yesterday I have serious issues with my IPad 3rd Generation; with Safari and ITunes.

Dear All,
If You could help me out pls!
Since Yesterday when I've opened Safari I could normaly get a google, and search for any site I want!
But as soon as I try to open any of searched pages it gives me a message:
" Cannot open the page because it couldnt connect with the server"
At first I could open some pages at least, but now cannot open any anymore!
I checked everything with WI-FI is OK as my mail is working normaly, but still
also have problme if trying to connect to ITunes it cant do connection!
Also cant check the software update?!
I try all resets somebody propose, reseting all settings, reseting networks, switching on and off,
chnaging DNS number but nothing helps?!
Dont know what ot try else!
Thanks a Lot

I did try that, right away, but no change!
I think there's no problem with wi-fi, but only with my device.
How come safari can open google page and i can browse and search for any pages,
and he will search and give me the list, but only when I want to open any of this pages
want work?! I dont understand this!

No POST, no beep with K8T Neo FIS2R

After buying all of the necessary parts, I assembled them, and was ready to boot up and install XP. The first time turned the power on, the floppy cable was in backwards and the system shut down. So I fixed the cable, and the system booted again. I got into the BIOS, and the system shut down again. Looking at the D-Bracket and Power LED, I thought that this was the CPU or power supply. At the time I was using a generic 425W PSU with only 12a on the 12V rail. After installing a new PSU and Processor, the problem still persists. I am getting rather frustrated with this and any help would be much appreciated. My sig describes exactly what I have hooked up right now. All four D-Bracket LEDs are Red and the Power LED is flashing every 2 seconds.

Hi
If your cutting out. with the power led flashing, thats the power protection mode, reset remove power cable for 5 secs and replace. However, it only really triggers when the CPU is overheated, or shorting.
Check you have not a bent CPU pin, then just a little paste and make sure its tight fitting to Heatsink
Other known causes, an extra pillar fitted to backplate shorting mobo, bent drive connector pins, USB devices, check that 4 pin square and 20 pin Mobo connectors are in fully and that no pins are discoloured. Short from spare molex, or fingers on backplate touching inside back connectors. CMOS jumper on wrong pins. Faulty PSU. Faulty Disk Drive or 4 pin floppy connector on wrong pins, Ram in wrong way round (has been done), dirt or debris on mobo, or in AGP slot or RAM dimms
Good luck
jocko

[MSI K8T Neo-FIS2R] 2xCMX512-3200 DDR400 memories (corsair)

I have this motherboard:MSI K8T Neo-FIS2R (MS-6702) and currently i'm using a Kingston memory and the computer runs fine. But i've buyed TWINX1024-3200 (2xCMX512-3200 DDR400) but when I put only this memories the computer after some time or when booting restart suddenly...
Could it be about the bios version, my actual version is v1.0 and I'm using AMI BIOS.
i've runned memtest+ and i get this: http://korpro.org/numb/PICT1348.JPG

I am in almost the exact same situation.
MSI Neo-FIS2R
AMD XP 2800+
2 sticks of DDR400 Corsair XMS memory (CMX512-3200C2) 512mb each (total 1gig)
Any combination of memory together does not allow the motherboard to boot. I get no beeping or warning sounds. Everything powers up but the display remains blank.
Things I have tried in many different combinations:
TRCD = 5, 4, 3, auto
DDR Voltage = Auto, 2.7, 2.65
DDR 200, DDR 300, DDR 333, Auto
Memory in bank 1+2, 1+3, 2+3
Along with those bios setting combinations, I have tried using several bios versions:
v2.2
v2.0
v1.9
v1.8
v1.4 <--- (Stuck with this bios for the moment, since the ami flashing utility HANGS when attempting to erase the boot block in step 2 of flashing procedure for any newer bios.)
As a consequence of several days of trying unsuccessfully to get both sticks of memory to work, I have given up hope on this motherboard.
Why is it so difficult to get two sticks of memory working properly on this motherboard?
Has anyone got another trick or technique or setting I can try that may work?
Alternatives:
Scrap the MSI motherboard -- never buy another piece of MSI crap again.
Buy a single stick of 1gig memory.
Buy a new motherboard from another manufacturer known to work properly -- at the very least not have these memory configuration issues.
Worst motherboard experience I have ever had, unfortunately.

MSI K8T Neo FIS2R- Corsair Twinx XMS4000

Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?

Quote
Originally posted by karinio
Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?
Hi dude i had identical problem, bought i extra stick 512 400 ddr and the system wont start. Make sure your motheoard support the made of ram. In my case Asus did not support corsaire. Also it could be the slots which are damage.
bye

How do you get your iPhone to stop connecting to face time while on a voice call? And it also does this when I'm on the phone with someone who doesn't have an iPhone. I look down at my phone while on a call and it says connecting to face time

How do you get your iPhone to stop connecting to face time while on a voice call? And it also does this when I'm on the phone with someone who doesn't have an iPhone. I look down at my phone while on a call and it says connecting to face time

How are you dialing these calls?

HT4993 How do you get your iPhone to stop connecting to face time while on a voice call? And it also does this when I'm on the phone with someone who doesn't have an iPhone. I look down at my phone while on a call and it says connecting to face time

How do you get your iPhone to stop connecting to face time while on a voice call? And it also does this when I'm on the phone with someone who doesn't have an iPhone. I look down at my phone while on a call and it says connecting to face time

How are you dialing these calls?

Boot and OS install issues with K8T Neo2 F

Can anybody shed light on my difficulties?
Assembled a new computer yesterday. First power-on produced nothing except 3 (2,3,4) red leds on d-bracket. After reading several postings, tried the following:
Swapped around memory modules;
Did repeated JBAT1 data clears (NB if you happen to get a board with the V1.0 user guide, note that the JBAT1 diagram appears upside down - pin one is closest to the SATA slots (page 2 - 24). The MSI downloadable user guide (V1.2) has that error corrected (page 2-25)
The only memory config that doesn’t produce three red leds is with one 512 stick installed in channel 3 (green).
Can now get to the point where Windows XP boots to the point where install is about to start, and then advises me that it can’t find a hard disk!
Have dis/reconnected the sata cable (using different cables) and checked the bios setup but can find nothing strange except that setup refers to the hard disk as BBS 0 (RAID) ST3120827AS - the reference to “RAID” worries me.

Paul, there have been people here that have had to strip their system down to the bare minimum hardware to get windows to complete the install, so try that. I had trouble completing my windows install as long as I was trying to install the RAID drivers at F6. So I ignored the prompt at F6 and windows installed fine. Then I installed my RAID drivers afterward.
These things are extremely sensitive when it comes to memory. I had the same problem you are having. Mine was cured by a BIOS upgrade to ver. 3.3. The simplest way to do it is to use "Live Watch". It will locate BIOS ver 3.3 for you, and download it to a floppy along with the flash program, and make it bootable all in one easy step. Then all you have to do is boot from the floppy you just made, and follow the instructions. Very simple.
I've read all these stickies and posts now going way back, and IMHO anyone who wants to use RAM thats not on the list should do so at their own risk. Interestingly enough, the recommended list from MSI is not the same as the list from AMD. And the memory manufacturers have their own lists of RAM that they say will work with this board. I'm using 2x 512 sticks of GEIL from the MSI recommended list.
Check out these links to see what I mean. By the way, if you haven't noticed, most of the older posts about memory problems are with respect to the K8T Neo FIS2R which is a socket 754 single channel board, so although they are similar, they're not the same. My point is just because his K8TNeo FIS2R works fine with brand "X" RAM doesn't mean your K8T NEO2 FIR will.
http://www.msi.com.tw/html/products/mainboard/testreport_pdf/6702E/memory.pdf
http://www.crucial.com/store/listparts.asp?Mfr%2BProductline=MSI+%28Micro+Star%29%2B+Motherboards&mfr=MSI+%28Micro+Star%29&cat=RAM&model=MS-6702E+%28K8T+Neo2-FIR%29&submit=Go
http://www.mushkin.com/epages/mushkin.storefront/EN/product/991140
http://www.amd.com/us-en/assets/content_type/DownloadableAssets/Athlon_64_Unbuffered_DIMM_AVL.pdf
http://www2.amd.com/us-en/Processors/TechnicalResources/1,,30_182_869_9460%5e9461,00.html?1094454813
Good luck!

I am having some serious issues with firefox, i can't print anything because it is stuck on fax and I can't use any of the drop down menus on any site

I am having some serious issues with firefox to the point of choosing another search engine. I can't print anything because it is stuck on fax and won't let me change it to my printer when i do try to select my printer it jumps right back to fax. The drop down menus do not work on any of the sites I go to. For example when purchasing clothes and you have to choose a size from a drop down menu I can't do it when I click on the drop down menu it doesn't work at all. I don't have a virus I ran my virus protector and no viruses are present. I don't have any suspicious issues going on with my computer so there has to be something in Firefox that is causing my issues. I tried internet explorer and I don't have any issues there. I hope you can help me because I love Firefox and would really like to continue to use it.

Lots of issues there, main one getting fcpx going again, try deleting the preferences using the utility deveoped by these guys.
http://www.digitalrebellion.com
Try deleting your render files and re-rendering the project.
Start with these and let us know how you go.
Tony

HELP: SERIOUS ISSUES WITH BILLING

I have had serious issues with BT since joining their service. Without getting into the issues we had with the BT homehub and other things at the start of the contract with them here is what's been happening.
When we joined BT we explained that we wanted a monthly direct debit. Sounds simple enough but apparently not.
I have phoned over 6 times in the last year to change this. It has still not happened. Several times we were told that on the system it said monthly for it to be then taken out quarterly. In July while we were away this happened again. Only as we assumed that as they had informed us it would definitely be on monthly direct debit that it was the money for the whole of the quarter was not there. So when they took the money for a quarterly bill again. We were charged. It has set back other bills as the money had been eaten up by charges for this. As you can imagine we were quite annoyed. This was not our fault and we felt that BT were not capable of holding our account details without taking money they we repeatedly requested not to. I admit we should have kept a closer eye on our bills account but you don't think that a company will repeatedly do this to you.
After phone calls it emerged that they would not say more than a 'sorry' about this.
The saga then continued. I cancelled the quarterly direct debit at the back and have asked BT to send me monthly paper bills. Then last month our phone and internet was cut off.
We rang up and suggested that due to the mix up could they add the money we owed to our monthly bills and we'd pay this off on top of the monthly bill. Despite that the reason we owe this at all is not through any fault of our own but through theirs. The money would have been available had they taken it as repeatedly requested.
We were on the phone for 1hr and 10 mins ( 21st September) to three different people. No, they said must be paid in 10 day. My partner only managed to get money off this in about an hour - the point being we were happy to pay the whole amount over a year and were not allowed. We asked to speak to a manager after 1hr and 10 and were put back to the start of the queue. 16 minutes later the man we spoke to said a manager named Samantha would call us back. No-one did.
On the 22nd of september a rather annoyed me called back and repeatedly requested a manager - sadi would be put though. After 17 minutes the phone went dead.
Called later on same thing phone went dead after requesting a manager at 10 minutes.
Later on called for 28 minutes and told the call centre the issue £20 deducted from amount but said it had to be paid in ten days and a bill would be sent. Was told that the internet would be reconnected that day.
23rd September was hung up on after thre minutes on requesting why the internet had not been connected.
Phoned later. The man that I spoke to said that no action had been put through to reconnect the internet. He would do it and it would be through by 5pm.
My partner phoned at 8pm when the internet still had not been reconnected. It was done the next day.
Today BT phoned to ask if I had the bill ( Not sent) and tell me that the line will be disconnected by the end of the day. i explained that we were in the middle of complaints procedures with them. She looked on the system and said that there were no notes on the account. I asked for a manager and then asked for this managers superior. She put me through to someone that when questioned was not her superior and half way through my explanation of this....you guessed it..... the line went dead.
I am so annoyed that we've been fine with bill paying and as of their mistake we're now in debt to them and feel like we can't sort it out as there is not anyone who will listen or help. Has anyone had similar probelms or does anyone have a number for their English call centre?
Jess

hi Jess,
I am really sorry that you have had so much trouble trying to get this sorted out. I'll get this straightened out.
Could you drop me in an email please to the address in my profile with your BT account and telephone number along with a link back to this thread.
Cheers
Craig
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)”
td-p/30">Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Who DOESN'T Have serious issues with K8T Neo-FIS2R

Similar Messages

Maybe you are looking for