Why am I unable to access an internet based services unless connected to WiFi

My iPhone connects fine to WiFi when at home,but when not at home, 3G will not allow me to access Facebook, Twitter, Safari, etc - just keeps saying loading, loading....

What service provider do you use? Have you ensured that 3G is on? Have you tried reseting your network connections? (settings-general-reset-reset network settings)
As an FYI it is a known issue that Verizon has been having data outages across the US.

Similar Messages

Unable to access the Internet over 3G Network, Wi-Fi fine.

Hi there,
I'm unable to access the internet on the iPhone 3G over the 3G network. Wi-Fi is fine, no problems there, but every time I try to bring up a website in Safari over 3G I get the message "Safari can't open the page because it is not connected to the Internet".
I have Enable 3G 'ON' under Settings > General > Network, and I have full strength on the signal meter in the top left of the Home screen. I'm in a city (Melbourne, Australia) on the Optus network, so the network itself shouldn't be the issue.
I've tried resetting the Network Settings under Settings > Reset > Reset Network Settings, but it didn't change anything. Any other ideas?
Cheers.

Well, there you go, fixed! Called Optus Customer Service and they were actually helpful! Apparently there were "some components in their back-end that needed to be installed manually." The man wasn't sure why they weren't there, "glitches, blah, blah..." but at least they're there now and I have 3G access.

UNABLE TO ACCESS THE INTERNET FROM LOCAL PROVIDER ON A SITE-TO-SITE VPN CONNECTION

Dear All,
I have a site-to-site connection from point A to point B. From point B i am unable to access the internet from local internet provider.
I am trying to ping from 192.168.20.1 the dns 8.8.8.8 but i receive the message "destination net unreachable".
When i run "show ip nat translation" i receive nothing.
The vpn connection is working properly, i can ping the other side 192.168.10/24
Below is the configuration of the cisco router on point B.
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.21.254
ip dhcp pool voice
network 192.168.21.0 255.255.255.0
default-router 192.168.21.254
option 150 ip 192.168.5.10
ip cef
ip domain name neocleous.ru
ip inspect name IOS_FIREWALL tcp
ip inspect name IOS_FIREWALL udp
ip inspect name IOS_FIREWALL icmp
ip inspect name IOS_FIREWALL h323
ip inspect name IOS_FIREWALL http
ip inspect name IOS_FIREWALL https
ip inspect name IOS_FIREWALL skinny
ip inspect name IOS_FIREWALL sip
no ipv6 cef
multilink bundle-name authenticated
vty-async
isdn switch-type primary-net5
redundancy
crypto isakmp policy 5
hash md5
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
lifetime 28800
crypto isakmp policy 50
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key Pb85heuvMde9Wdac5Qohha7lziIf142u address [ip address]
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 10
crypto ipsec transform-set TRANSET esp-aes esp-sha-hmac
crypto ipsec transform-set TRANSET2 esp-des esp-md5-hmac
crypto ipsec df-bit clear
crypto map CryptoMAP1 ipsec-isakmp
set peer [ip address]
set transform-set TRANSET
match address CryptoACL
interface FastEthernet0/0
description Primary Provider
ip address [PUBLIC IP MAIN PROVIDER] 255.255.255.252
ip access-group outside_acl in
ip mtu 1390
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
crypto map CryptoCY
crypto ipsec df-bit clear
interface FastEthernet0/1
description TO LAN
no ip address
load-interval 30
speed 100
full-duplex
interface FastEthernet0/1.1
description DATA VLAN
encapsulation dot1Q 20
ip address 192.168.20.254 255.255.255.0
ip access-group inside_acl in
ip nat inside
ip inspect IOS_FIREWALL in
ip virtual-reassembly in
ip tcp adjust-mss 1379
interface FastEthernet0/1.2
description VOICE VLAN
encapsulation dot1Q 21
ip address 192.168.21.254 255.255.255.0
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface FastEthernet0/3/0
no ip address
ip access-group outside_acl in
ip nat outside
ip virtual-reassembly in
shutdown
duplex auto
speed auto
crypto map CryptoCY
ip local pool VPNPool 192.168.23.2 192.168.23.10
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source list nat_list interface FastEthernet0/3/0 overload
ip route 0.0.0.0 0.0.0.0 [default gateway ip]
ip access-list standard VTY
permit 192.168.20.0 0.0.0.255
ip access-list extended CryptoACL
permit ip 192.168.20.0 0.0.0.255 192.168.3.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.5.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.6.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.12.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.2.0 0.0.0.255
permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
permit ip host 192.168.22.1 192.168.5.0 0.0.0.255
permit ip host 192.168.20.1 192.168.5.0 0.0.0.255
permit ip host 192.168.22.1 192.168.6.0 0.0.0.255
ip access-list extended DFBIT_acl
permit tcp any any
ip access-list extended inside_acl
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.35
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.39
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.23
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.18
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.55
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.144
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.146
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.141
permit ip host 192.168.20.253 host 192.168.3.21
permit ip host 192.168.20.254 host 192.168.3.21
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.10
permit ip 192.168.20.0 0.0.0.255 host 192.168.20.254
ip access-list extended nat_list
deny ip host 192.168.20.254 192.168.10.0 0.0.0.255
deny ip host 192.168.20.254 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.10.0 0.0.0.255
deny ip host 192.168.20.2 192.168.3.0 0.0.0.255
deny ip host 192.168.20.2 192.168.10.0 0.0.0.255
permit ip host 192.168.20.1 any
permit ip host 192.168.20.2 any
permit ip host 192.168.20.254 any
ip access-list extended outside_acl
permit gre any host [ip address]
permit esp any host [ip address]
deny ip any any
ip sla 2
icmp-echo 192.168.10.254 source-interface FastEthernet0/1.1
frequency 180
timeout 500
ip sla schedule 2 life forever start-time now
logging 192.168.3.21
route-map DFBIT_routemap permit 10
match ip address DFBIT_acl
set ip df 0
route-map ISP2 permit 10
match ip address nat_list
match interface FastEthernet0/3/0
route-map nonat permit 10
match ip address nonat_acl
route-map ISP1 permit 10
match ip address nat_list
match interface FastEthernet0/0

You cannot access internet, because all traffic is tunneled for VPN !!!!
Please see cisco tech documentation and bypass traffic for internet.
eg. if lan traffic is going from site a to site b then through vpn
else
lan traffic to internet (any) should be out thorugh the vpn .

After updating Firefox yesterday I have been unable to access the internet. I have tried the Norton 360 fix several times, but it still doesn't work. How can I get Firefox working again?

After updating Firefox yesterday I have been unable to access the internet. I have tried the Norton 360 fix several times, but it still doesn't work.

After updating Firefox yesterday I have been unable to access the internet. I have tried the Norton 360 fix several times, but it still doesn't work.

Users unable to access the internet sites

Hi Everyone,
We have users who are able to get the IP address but unable to access any internet sites.
I check the trap logs on the WLC
RADIUS server 192.168.50.1:1812 failed to respond to request (ID 16) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.50.1:1812 activated on WLAN 1
RADIUS server 192.168.60.1:1812 deactivated on WLAN 1
RADIUS server 192.168.60.1:1812 failed to respond to request (ID 200) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.60.1:1812 activated on WLAN 1
RADIUS server 192.168.50.1:1812 deactivated on WLAN 1
RADIUS server 192.168.50.1:1812 failed to respond to request (ID 15) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.50.1:1812 activated on WLAN 1
RADIUS server 192.168.50.1:1812 failed to respond to request (ID 16) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.50.1:1812 activated on WLAN 1
RADIUS server 192.168.60.1:1812 deactivated on WLAN 1
RADIUS server 192.168.60.1:1812 failed to respond to request (ID 200) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.60.1:1812 activated on WLAN 1
RADIUS server 192.168.50.1:1812 deactivated on WLAN 1
RADIUS server 192.168.50.1:1812 failed to respond to request (ID 15) for client 88:53:2e:99:24:b5 / user 'unknown'
RADIUS server 192.168.50.1:1812 activated on WLAN 1
Need to know how can i troubleshoot this further?
Regards
Mahesh

I would do the troubleshooting in following sequence.
1. Put a wired PC on to the vlan allocated for WLAN1
2. Check whether wired PC gets an IP & can browse internet
3. If that works, then we know no issue of DHCP & not issue with L3/NAT routing to access internet
4. If step2, does not work then your issue is not within wireless, you have to change the focus of your troubleshoot.
5. If step2 works, then test a wireless client with OPEN Authentication (No ACS involvment).If this does not work,then it means wireless client does not get proper IP connectivity. Check dynamic interface configuration for this WLAN & make sure gateway addresses correctly configured. Also VLANs are trunk across to WLC from switch.
6. If step5 works, then try your client with ACS & see the client get successfully authenticated. If not it may be WLC to ACS issue. Troubleshoot that in that case.
Do some troubleshooting like this & let us know the outcome. I am sure you will abe to find out the issue easily in this way.
HTH
Rasika

TS1398 When my iphone connects to wifi, everything else in my house will not connect to the internet. They all show 3 to 4 bars on connection strength, but unable to access the internet. The second I turn off the wifi on my iphone, everything runs perfec

When my iphone connects to wifi, everything else in my house will not connect to the internet. They all show 3 to 4 bars on connection strength, but unable to access the internet. The second I turn off the wifi on my iphone, everything in my house runs fine. What is going on?

Had a similar problem a number of years ago with a laptop my daughter had. The probelm turned out to be the router. What kind of router do you have? Have you checked for firmware updates, or at least tried re-booting it?

HT4623 ios 6 unable to access 3g internet?

I recently updated to ios 6 (iphone 4s). Since the update I have not been able to access the internet (Telstra 3G) unless I have a wireless connection What can I do to fix this?

Can you dial *228, option 1 to reprogram your phone to the Verizon network?
The other thing I wonder is if the phone was activated properly in Itunes.

I don't have a DSL or cable modem to access the Internet ... just a mobile WiFi (there is no cable available at our house). How do I connect my Time Capsule to the Internet via the mobile WiFi?

I don't have a DSL or cable modem to access the Internet ... just a mobile WiFi (there is no cable available at our house and the mobile WiFi is our only option). How do I connect my Time Capsule to the Internet via the mobile WiFi?

LOL!!
I am in Australia and the ISP... I think both the main ones would fit your description to a T.. big T in particular.
Your router is really unsuitable.. if it is only wireless and no ethernet.. just buy an ethernet one.
Do a search on ebay.. 3g router.
But you can get the TC to join a wireless network.
It is a non-standard setup that Apple will not support.. the option is hidden.
If you are on Lion download the 5.6 utility. Go to the wireless set up page and hold down the option key whilst selecting wireless mode.. a new option, join will appear. You can then put in the ssid and passkey of the 3g router.
But please note the end result of this setup..
very slow speed. The TC is now a second wireless hop from your clients.. this will halve the speed.
In this mode the ethernet are deactived.. for reasons only Apple know, they decided you should not use ethernet when doing this.

How can I access the internet on my ipad mini while wifi signal is strong, how can I access the internet on my ipad mini while wifi signal is strong

how can I access the internet on my ipad mini while wifi signal is strong,

Your question isn't clear enough. If it's a strong signal, you're good to go.

I can't get the Siri dictation tool to work when I access the Internet via Wi-Fi at work. It will work if I access the Internet with a cellular connection. What can I do to get it to work on the Wi-Fi?

I can't get the Siri dictation tool to work when I access the Internet via Wi-Fi at work. It will work if I access the Internet with a cellular connection. What can I do to get it to work on the Wi-Fi?

Thanks for your note. My tech dept could not come up with any explanation for the dictation tool not working. We have about 1,000 employees in our office - I think I will send an all employee message to see if anyone else has the issue.

HT6010 I have tried to update my iOS 7.3.0 and I keep getting a msg saying bit connected to the Internet and I am connected by WiFi plus my phone has Internet connected also, I have repeatedly clicked on retry, still get message bit connected to Internet

I have tried to update my iOS 7.3.0 and I keep getting a msg saying bit connected to the Internet and I am connected by WiFi plus my phone has Internet connected also, I have repeatedly clicked on retry, still get message bit connected to Internet

Try this support document http://support.apple.com/kb/TS3694 and look at this section.
Unable to contact the iOS software update server gs.apple.com
Error 1004, 1013, 1638, 3194: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors:
Install the latest version of iTunes.
Check security software. Ensure that communication to gs.apple.com is allowed. Follow this article for assistance with security software. iTunes for Windows: Troubleshooting security software issues.
Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. Follow iTunes: Advanced iTunes Store troubleshooting to edit the hosts file or revert to a default hosts file. See section "Blocked by configuration: (Mac OS X/Windows) > Rebuild network information".
Try to restore from another known-good computer and network.
If the errors persist on another computer, the device may need service.

Why am I unable to access my new Post Office Account they state that you will not allow and I will have to use Internet Explorer why?

I have just opened a new account with the Post Office but I am unable to access this on the net. Telephoned Customer Services but say that I will not be able to access through Firefox and will have to use Internet Explorer. Going back to Internet Explorer is not something I want to do because I like Firefox, please explain why Firefox is blocking access if this is true. I have clicked 'allow' but it made no difference and the only message coming up is "timed-out" when I have been much less than 5 mins putting security details. Please advise. Paula

I doubt if Firefox is blocking access. More than likely, that website is made to use ActiveX, or other proprietary Microsoft code, that only Internet Explorer can handle.
If you post the address of that "Post Office" website, maybe one of us support helpers can figure out the exact reason for that.

Apple ID does not have permission to access iTunes Connect. Why am I unable to access iTunes Connect?

I recently signed up as an Apple Developer, but I'm still unable to access iTunes Connect. Why is this?

How recently?
Are you outside the US?
Which browser are you using?

Connected to Wi-Fi network, but unable to access the Internet ipad 2

Hello,
i baught a new ipad 2 32 gb , 3g.... 4.3.5os
i am having an annoying issue regarding the internet connection..
where i am living i cannot connect a router so my laptop has a cable connected to it to access internet ... i had to create an ad-hoc ( to make my laptop work as a router)
( windows 7 btw)
now my iphone connect fine and i can browse internet, but when it comes to my ipad it only connects to the wi-fi but when i open the safari , a message pops up saying no internet connection eventhough as i said it's connected to WIFI with full signal !!
this is really frustrating and i've read many many blogs about this issue but none of them solved my problem and this was my last option is to send u guys askin for help...
p.s: i tried to click on renew lease but nothing is changed
ip adress : 169.254.90.xxx
subnet mask:255.255.0.0
router : blank
dns:blank

Try using an explict DNS server, such as
208.67.222.222 (OpenDNS server)
8.8.8.8 (Google DNS server)
System Preferences -> Network -> Advanced -> DNS -> [+]
The first entry you add (at the top of the list) will be the primary DNS server.

I have just purchased Photoshop Elements 13. Why am I unable to access the program?

I have just purchased Photoshop Elements 13. I think it was installed. The title shows in my 'Downloads File'. I have tried double clicking on 'install' in the downloads file. All I get is a page of data that doesn't seem to do anything. When I purchased Photoshop Elements 12 there was no problem. The apps appeared on my monitor and I went to work. What appears on my monitor for Photoshop 13 is a file picure. When I click on it I go to the Downloads File. Can anyone help me?

I am unable to access the Photoshop Elements 13 program.

Why am I unable to access an internet based services unless connected to WiFi

Similar Messages

Maybe you are looking for