Why can't one of my Airport express stations extend my wireless network?

Background:
I have an Airport Extreme cabled to my Comcast router.
I have three Airport Express units scattered around my house.
All have worked fine for many months and all are running version 7.6.4.
Problem:
Recently, one of the Airport Express stations had a yellow, flashing LED and a status of "Extended Network - This Airport base station was unable to extend the wireless network..."
Using Airport Utility, this station displays a connection quality status of "good."
This unit also has the exact same settings as my other two Airport Express units.
Using Airport Utility I instructed the unit to "Ignore" the status, and the LED turned green. But the status of "Extended Network" continues to display.
I've tried a hard reboot of the unit, but nothing changed.
Any suggestions as to how to correct this status?

Thanks for the suggestion, but apparently the culprit was my Airport Extreme.
I swapped the locations of two of my Airport Expresses and the problem replicated. Both had the "Extended Network" status and both showed a red number 1, indicating that a firmware upgrade was available (but no update button appeared). I returned the two Expresses to their original locations. Same situation after they booted.
Then I performed a hard reset of my Airport Extreme. After the reset, all three Airport Expresses now have no special status messages in Airport Utility and all have a connection of "good" or "excellent." Plus, no red number 1's appear (which should only appear if a firmware update was available).
So, problem solved.

Similar Messages

Using Airport Express to extend my wireless network

I recently purchased a Time Capsule but found that I could not see the wireless signal from my bedroom. To solve this I purchased an Airport Express to extend the range. I plugged the AE into an outlet in my bed room and set it up to join my existing network. Everything looked fine from the point of view of the Airport Utility. Unfortunately my iPod Touch still can not see my wireless network from my bedroom. I new iPad can see it but the signal is very weak, even when I hold it right next to the AE. Is there a setting I missed?

Rick, welcome to the discussion area!
I plugged the AE into an outlet in my bed room and set it up to join my existing network.
You need to configure the AirPort Express to "Extend a wireless network". The AX does not provide any additional wireless coverage when it is set to "join".
First, you need to check a setting on your Time Capsule as follows:
AirPort Utility > Manual Setup > Wireless tab (below the icons)
Make sure there is a check mark next to "Allow this network to be extended"
Update to save any changes
On the AirPort Express move it close to the Time Capsule for configuration:
AirPort Utility > Manual Setup > Wireless tab
Wireless Mode = Extend a wireless network" (Hold down the option key on your Mac if you do not see this choice appear when you click the selection box).
Wireless Network Name = Same name as your Time Capsule Network
Check mark next to "Allow wireless clients"
Security = Same setting as your Time Capsule
Password = Same password as your Time Capsule
Confirm Password
Update to save settings
The AirPort Express can only "extend" what it "receives". Most users position it too far away from the main router and consequently, the Express extends a weak signal. Try a location that is about 1/2 to 2/3 the distance between the Time Capsule and the area that needs move coverage. Then experiment a bit to find the best signal.
Post back on your results.

Can I use my airport express to extend a wireless network with a non-apple router?

I have been trying to extend my wireless network in my house. Right now I have a dsl modem/router provided by Century Link and an older AirPort express (not sure how old but it uses AirPort utility v5.6). I want to be able to share my printer and use AirTunes. Currently I have the AirPort plugged into the router and setup to create a new wireless network. I would like to combine them so I don't have to switch between to print and play music. I am not really sure where to start or if it even possible. Any info would be great!

If you keep the Express connected using Ethernet and configure the Express to "Create a wireless network" using exactly the same wireless network name, exact same wireless security and same wireless password as the Century Link network.....everything will behave as one "big" network, and you will have additional wireless coverage near the Express.
If you do not need extra wireless coverage, you can turn off the wireless on the Express.
The Express must be in Bridge Mode.
Most users know the name of their wireless network and password, so the really tricky part of doing this is that you must know exactly what type of wireless security settings the Century Link router is using....and then match up the same settings on the AirPort Express.
If the settings do not match up exactly, then you wind up with two separate networks that will each require their own log on.
If you can check the setting for wireless security on the Century Link router and provide that information to us, we can tell you how to set things up the way that you would like.

How do I use airport express to extend my wireless network?

How vcan I extend the range of my wireless network using Airport Express?

It appears that you may have "join a wireless network" and "extend a wireless network" mixed up a bit.
The Express can "join" virtually any wireless network produced by any manufacturer's router if it is provided with the correct settings:
name of the wireless network
the correct wireless security settings
and correct password.
"Join" is normally used for AirTunes or to connect a USB printer to the Express for remote printing.
But, the Express does not provide any additional wirless coverage when it "joins" another wireless network.
Apple's "Extend a wireless network" feature, which was introduced about 5 years ago, allows the Express to connect to another Apple "n" wireless router and then "repeat" or "extend" the wireless signal....providing more wireless coverage in the area where the Express is located.
This is a proprietary setting. Apple says it will not work with devices from other manufacturers. To our knowledge, this is correct.
Prior to 2007, Apple used a setting called WDS to allow the Express to be configured to provide more wireless coverage. Attempts were made by a number of manufacturers to standardize the WDS settings, but things were never finalized.
The result is that Apple's older "b/g" routers were sometimes compatible with WDS settings from another manufacturer. There were a handful of products....5 or 6, as I recall....that were said to work. Some did, some didn't. Linksys had a couple of models, Netgear had one, SMC another, etc. Extremely limited.
Since WDS was never adopted as an industry standard, manufacturers developed their own WDS settings. Compatibility was extemely limited and unreliable. That continues to this day with WDS.
Bottom line....It is always best to stick with the same manufacturer throughout your network as far as routing is concerned.
If you have an newer "n" Apple router like an AirPort Extreme, the Express can extend the wireless as can along Extreme. If your Extreme is dual band, and you want to extend both bands, then you need another Extreme.
Another responder suggested to someone that they could connect the AirPort Express to a router via Ethernet. What exactly would that achieve?
That is a completely different subject since this discussion is about extending a wireless network using wireless only.

HT4259 Trying to set up airport express to extend my wireless network. Primary base station is a time capsule. Even when I plug in the airport express to mac it cannot find it.

Trying to set up airport express to extend my Wi-Fi network. Primary base station is a time capsule. Tried searching for airport express using Wi-Fi status, no luck. Even tried plugging airport express into iMac, still no luck. Airport express showing solid amber light. Thanks for any help.

Airport express showing solid amber light
Unfortunately, this can mean one of two things:
1) The Express is locked up and will need a Factory Default Reset procedure to try to return the device back to its original default settings so that it can be reconfigured again.
2) The Express is defective. If you cannot get the Express back to a slow, blinking amber light after a Factory Default Reset, the Express will need to be replaced.
Try the Factory Default Reset a few times and report back on your progress.
Resetting an AirPort Base Station or Time Capsule FAQ

Can I use an additional airport express to extend my wifi network

Hi,
I have an airport express running my wifi network but I have black areas in farthest away areas. If I buy a further express would that extend my network ? If so what would I need to do !
Tnx

Hi Matt
Thanks for reply - my speed is already poor - what would be a better solution ?
Tnx again

Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?

Can I run a cat5 cable to a 4 port hub from a cisco router then connect one of the hub's output ports to an airport express to 'extend' my wireless range?
Flow would be
Cable modem---->cisco e2000 wifi router (This is broadcasting wifi but not strong enough)---->4 port hub ---->airport express (to extend the wifi in another part of house)
thanks!

Yes, you can do this as you stated. In essence you will want to configure both routers for roaming network. Please check out the following Apple Support article that describes this type of network. Although this article uses two or more AirPorts, it can be done with just about any manufacturer's router.

I did set up my Airport Express to extend my existing network. It did ok but I can't see the name assigned to the Airport Express name in my available networks. Is that normal?

I did set up my Airport Express to extend my existing network. It did ok but I can't see the name assigned to the Airport Express name in my available networks. Is that normal?

If the AirPort Express is extending your network it is using the same wireless network name as your "main" router.
Your main router and the Express act like one "big" network now.
Your computer will connect to either the main router or the Express automatically....depending on where it sees the best signal.

How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly

I want to extend my wifi off my Time Capsule with an Airport Experess in a part of my house that has no data cable ran to it. How do I do this?
Thanks

No more meseges.
في ٢٦/٠٨/٢٠١٤، الساعة ٢١:٤٥، كتب Apple Support Communities Updates <[email protected]>:
New discussion activity
Bob Timmons has posted in the AirPort community.
How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly
Assuming that you have the model A1264 or A1392 version of the Express, it must be located where it can receive a strong wireless signal from the Time Capsule to be able to extend it correctly.
A good general location would be a point that is about half way between the Time Capsule and other area that needs more wireless coverage.
You will use AirPort Utility on your computer to configure the Express. An iPhone or iPad could be used as well.
We can provide more help....if you need it....but we'll need to know what version of AirPort Utility that you are using on your computer....or whether you want to use an iPhone or iPad to setup the Express.
https://discussions.apple.com/servlet/JiveServlet/downloadImage/2-26506753-46613 2/AboutAirPortUtility.png
To post a reply, go to the discussion in Apple Support Communities.
You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile.
TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
All Rights Reserved | Privacy Policy | Terms of Use | Apple Support

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

Why Can't I use BT when I am using the wireless Network?????

Why Can't I use BT when I am using the wireless Network?????
I am using airport extreme.....

In an inline renderer, the compiler knows which document will be the “outerDocument” so it sets up special code to assign that value. I think you can use parentDocument or owner.document

Just installed a new time capsule and i want to use my airport express to extend my wireless range....time capsule working with existing devices at this time...but i am not able to get airport utility to recognize the airport express.....????

just installed a new time capsule and i want to use my airport express to extend my wireless range....time capsule working with existing devices at this time...but i am not able to get airport utility to recognize the airport express.....????

Temporarily connecting your AirPort Express to one of the Time Capsule's Etherent LAN <-> ports...as LaPastenagure suggests....is always a good way to setup and configure other network devices.
If you want to configure the Express using wireless, remember that the Express broadcasts a default wireless signal with a name like Apple Network xxxxxx. You must log on to this network first....no password is required....then open AirPort Utility to "see" the AirPort Express.

Tried to use my two airport express to extend my wifi network on a windows pc but no success

Tried to use my two airport express to extend my wifi network on a windows pc but no success

My two airport express base stations are 802.11n and i am triying to use them extend my wireless network which is using a D link wirless router as supplied my my ISP connected to TalkTalk network.
Unless the D-Link wireless router has Ethernet ports for each of the 802.11n AirPort Express Base Stations (AXn) to connect to, they will NOT be able to extend the wireless range of the D-Link.
Instead, when directly connected and reconfigured for a roaming network, these base stations CAN extend the range.
Please check out this Apple Support article on how to use AirPorts to extend a wireless network.
The key is to have both AXns configured as follows:
As a bridge.
Each having a unique Base Station Name.
Both using the same Network Name (or SSID), wireless security type and password as the D-Link.
Each AXn to use a channel at least 3-5 channels apart both from each other and that of the D-Link.

Why can't I use old Airport Express this week after power outage?

After purchasing a new Airport Express station, my older one was also able to work (the older is Model A1084). It connected "under" the tree of the new Express in the new Airport Utility (under OS 10.10.1 Yosemite). I could see the same hierarchy on my iMac and iPhone with the Airport Utility. More importantly, I could stream music to speakers connected to the older Express Station.
But after a power outage last night, I had to turn off all devices. The Wi-fi network is up and running EXCEPT for the older Airport Express. When I try to connect it I get the message "The Airport Express named (Name) cannot be set up by this software. Go to apple.com/support/airport for more informat
1. Is is possible to get the older version of the Utility software installed so I can set up this older device?
2. If it worked two days ago, why would it stop with the power outage?
Thank you!

1. Is is possible to get the older version of the Utility software installed so I can set up this older device?
Unfortunately no, at least not on the newer OS X versions. Basically since OS X Lion, Apple stopped supporting the older 802.11g AirPort base stations. You would to use either a pre-Lion Mac or a Windows-based PC to administer these older base stations.
2. If it worked two days ago, why would it stop with the power outage?
Not sure how you were able to administer the Express using v6.x of the AirPort Utility before. It shouldn't have been possible.

Why does Airport Express slow down my wireless network??

Hello, guys! Here I am again, seeking for help...
Ok, so here's the situation: my internet service provides me with 10Mbps. My cable modem is hooked up to a 4-month old Airport Extreme in my home office, two walls away from the living room, where I'm typing from now. Internet's wireless speed in this living room has always been about 10Mbps, barely any loss when switching my signal from cable to wireless.
I then decided to buy an Airport Express in order to extend my wireless network, since I want to work in a room far from this living room and with Airport Extreme alone I got no internet signal there.
Ok, so I installed the Express right at the living room (I can say it's pretty much at the middle of the house) and now I got full internet sign at the far room, great!
HOWEVER, my wireles speed has been cut by half!! At this very same living room where the signal was 10Mbps before I installed the Aiport Express, it's now - at the very best!- 5Mbps!! Needless to say that it's even slower at the far room it was intendend to extend the signal to, but that was kind of expected.
*But why does it cut in half my internet speed at the living room if Airpot Extreme IS delivering 10Mbps at that point of the house??* Am I not setting it up properly, how can I solve this??
Thank you so much for any help you can give me!
Cheers,
Renata
Message was edited by: rgobrasil

After some more analysis, I discovered that this tends to happen everytime a Time Capsule backup is performed.....

Why can't one of my Airport express stations extend my wireless network?

Similar Messages

Maybe you are looking for