Why do I get a boot drive not found error only when laptop lid has been closed?
I've got a HP Mini 210 P/Number: VX818EA with Windows 7 Starter.
It works fine when turning on after shutdown, but when I've put it to sleep by closing the lid it won't 'wake up', and I get a blank screen. On restarting the computer I get a 'boot drive not found' error, (3F0) which can be resolved by following the steps on this page: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443463&tmp_task=solveCategory&lc=en&dlc=en&cc...
I've run disk check etc as suggested on that link, no errors are found, but nothing seems to resolve the problem more than temporarily. Seems odd that this only happens if I close the lid (sleep mode with the lid up is fine, doesn't crash the computer).
Can anyone advise?
Thanks
Hello,
Very strange, can you go to BIOS and reset the setting " By Default " ?. How did you check the disk ?
This is an unusual probleme Hp Mini 210 . And notice me after your reset the bios settings.
Similar Messages
-
Captivate 8: Why am I getting a HTTP 404 Not Found error when I try to preview a responsive project?
Captivate 8: Why am I getting a HTTP 404 Not Found error when I try to preview a responsive project?
Out of curiosity, some here have recommended renaming an EXE file behind the scenes to eliminate that firewall message when starting up. Are you one of those folks that tried this? My thought is that if so, perhaps this is a result?
Cheers... Rick -
The programme uninstalled was F-Secure internet security, and fslapi.dll (I think) was one of the library files. No when I start Firefox browser, it gives me that error. Evidently some part of Firefox is still thinking the dll file should be there.
How do I stop the error message occurring?SadisticIron wrote:
i just baught my first iphone and it is a jalbroken
Buzz! Thank you for playing!
Discussing jailbroken devices is forbidden here by the Terms of Service.
You can not get help here. -
Hard disk error "boot drive not found...."
After screwing around to see how hard it would be to upgrade my hard disk, I started getting the ol' boot device not found error.
So, I went online on another machine and found that I could boot into a menu of boot devices by holding down the OPTION key. It presents me with options to boot from DVD, external drives, network, or lo and behold my MacHD. If I select my MacHD, after a minute it will boot as usual and present me with the
logon screen. I could just let it go and continue to do this, or what can I do to put it back the way it was so I can boot without holding down a key?
My intention is to upgrade to a 2TB drive as I see it's easy enough for me to do myself.Try SMC and PRAM resets:
http://support.apple.com/kb/HT3964
http://support.apple.com/kb/HT3964
Ciao. -
Computer turns itself off and says boot drive not found, what do i do?
computer turns itself off and says boot drive not found, what do i do?
Hi,
Please use instructions from the following link to check and fix:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443463&cc=ad&dlc=en&lc=en&jumpid=reg_r1002_in...
Good luck.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. -
Boot Device Not Found Error Message
I've had my laptop since May 2011. HP Pavilion dv6
Quad-Core AMD Phenom II 2.2 GHz
DDR3 SDRAM 8 GB
500 GB Serial ATA 7200 rpm hard drive.Originally Windows 7 64-bit upgraded to Windows 10 64-bit One morning I turned on my laptop and I received the following error. The laptop lives on my desk, hasn't undergone any major changes, and I haven't moved or dropped it. I've run every diagnostic test from the F2 menu. The hard drive and memory both passed, the system tune up passed, and I've restored the BIOS to the default settings with no changes. If I hold the power button and restart the laptop usually on the 2nd or 3rd attempt the system will start normally with no issues and continue on as if nothing is wrong. This is a helpful work around but it doesn't solve the problem which is a bit of an annoyance and leaves me worried that eventually it might refuse to start at all. Thinking that a system restore might help I ran a recovery and brought it to an "out of the box" state. After that failed I decided to go ahead and upgrade from Windows 7 to Windows 10. I performed a clean install keeping none of my programs or personal files. Despite a successful Windows 10 install I still receive the same error every time I restart. The short version:When I turn on my laptop I encounter a Boot Device Not Found Error Message.My hard drive passes diagnostic tests.My laptop will start eventually if I continue to power cycle it.@pkharel ,
Hello and thank you for posting on the HP support forums. So that I can better help you here with this hard drive issue . Can you explain what diagnostic you ran on the hard drive.
Did you run the diagnostics from the BIOS?
HP Notebook PCs - System Diagnostics (F2)
HP PC Hardware Diagnostics
If you have attempted the diagnostics from the BIOS and are not finding the Hard drive. See if you can find the hard drive in another computer. If you can not find it using another computer replace the drive. If you can and it is not located on your notebook then you have a possible issue with the motherboard.
First thing I would do is try and restore your BIOS first.
Restoring the BIOS
After attempting this and you still can not find the Hard drive and you can see it in another system please contact HP phone support for repair options.
Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
If the hard drive is not detected in another system then replace hard drive.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP -
File Not Found error (-43) when trying to record
Never had this problem in the past, and haven't used Logic in a few months, but every time i attempt to record, i get that message: File Not Found, Result code error -43
I am using the MBox 2 Pro as my record in, and Logic 6.4.3
Thanks for the help...Hi,
I have a 'file not found' problem with Logic Express. A while back I transferred all my Logic files to DVD to make room on the hard drive. It took 4 discs, saved alphabetically by song title. Now, I nearly always get the 'file-not'found' error message when I try to work on something. Sometimes when I click 'search' it finds the file, sometimes it doesn't. I'm confident that I didn't delete the files.
Wondering if 'search' would find the files if I transferred all the files from DVD to a single folder on an external drive. I don't use the 'search manually' option, because I'm not really sure what I'm looking for, or where to look. In the other room, perhaps? 'Computer challenged' is me. Any suggestions?
DS -
[Athlon64] Serial ATA Drive Not found Error on bootup ATI Radeon RS480M2-IL
MSI "RS480M2-IL" ATI Radeon XPRESS 200 Chipset Motherboard For AMD Socket 939
I have just built an Athlon 64 system using the motherboard stated above. When I boot the system up, I get an error message stating that the system can not boot up from the CD 95% of the time. I then use Ctrl-Alt-Del and the system boots up just fine. I have the BIOS set to search the hard disk first for boot up before looking at the CDROM and I still get this error. I believe it can not find the hard drive due to timing or what???
We did load the MS XP 64 bit operating system at first, but we found that there were ot enough drivers available. We then did a quick format and loaded the the MS XP Pro operating system after that. Everything works fine except for this error message we get 95% of the time on bootup. We are using a serial ATA 80 GB Western Digital Hard drive and a Lite-On dual layer DVD burner(IDE).
Power supply is a Macron
+5v=30A
+12v=15A
-5v=.5A
-12v=.8A
+3.3v=14A
+5vSB=3AHi,
until I was using BIOS 3.2, the system works very fine. After upgrading to BIOS 3.3, my system usually did not boot after cold restart (button) but then after warm restart (ctrl-alt-del) always started. It was not usable because I use scheduled starting of PC to record TV programs. Every cold restart SATA boot drive boot was not found but after warm restart everything OK. So I reflashed back bios 3.2 and the system works perfectly again.
Any one similar experience?
p.s. With 3.2 BIOS I am very satisfied with this motherboard and its stability. But not sure about future upgrading BIOS :-( -
I am trying to install itunes on my computer (Windows Vista). After initial instillation I got an error 42404 A required itunes componenet is not installed; please repair or re-intall itunes and error 50, cannot access itunes store at this time. Please try later. I have done that multiple times; uninstalled all components, reinstalled all components, repaired all components, restarted my computer. I have changed firewall settings to allow acess to all of the apple components. I have made sure the required ports are open. All of the components are showing on the installed programs section of my control panel.
I am now getting an error message that says that Apple Support Application is not found error 2 (windows 5). It is listed in the installed programs and I have repaired it.
I am out of options. And help would be appreciated.'The installer has insufficient privileges to modify this file C:\Program Files (x86)\Common Files\Apple\Apple Application Support\Web kit.resources\inspector\Images\Spinner Inactive Selected.gif.'
That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards? -
SAP Design Studio ODBC Driver Not Found error while creating HANA connection.
Hi,
While creating SAP HANA ODBC connection in Design Studio via Tools > Preference > Application Design > Backend Connection. I am getting error ODBC Driver Not Found. Error screen shot is attached.
My Design Studio version is 1.3 win 32 bit
My OS Win 7 64 bit
I have installed both HANA client 32 bit and 64 bit.
I have tried creating DSN ODBC connection via "C:\Windows\SysWOW64\odbcad32.exe" and via Control Panel > Administrative tools > Data Sources(ODBC). But it does not detect it either.
I am not sure what needs to change to let Design Studio know which HANA client driver to use.
Please help!.Hi Rohit,
This seems to be a known bug with Design Studio. Please see the SAP Note below on this.
1774480 - Fix launching of ODBC Data Source Administrator
Regards,
Abhijit -
Boot drive not found (folder with blinking ?, etc)
Ok, I'll give some background. I may be misquoting some of the error messages, but I'll try to be as close as possible...
This is on a Early 2011 15" MBP running 10.9.1. Harddrive has been replaced with an SSD.
I was running low on space so I deleted a bunch of stuff - all form my home folder. Noticed that the free space wasn't there and I figured, hey, Filevault, so I rebooted to give it a chance. No problem,rebooted and there was a lot more disk space. For some reason I then decided it'd be a good idea to run Disk Utility and do a Verify on the disk. That's when the problems started.
Verify told me I should run a repair, so I did. Repair told me it can't repair the disk right now, but that I should reboot, hold down CMD+R and use the Disk Utility from THERE to do the repair.
So I did. Rebooted, CMD+R, Recovery, Disk Utility, Repair.
The Repair in there told me "Live File System Repair is not supported" or something to that effect.
So I figured I'd reboot and google that.
Only after that, I get the flashing question-mark folder.
So I figure it just forgot where the startup disk is. I power off and power back on while holding Option.
And the only option it gives me is "Internet Recovery".
I tried a whole bunch of times. Nothing. Eventually I went into Internet Recovery, ran THAT Disk Utility. That sees my drive just fine. I can double-click and enter the password tolet it access it, and I was even able to run the repair then! (it found a couple of very minor things). I ran repair permissions, too, just for good measure.
When I quit recovery it told me I might want ot choose a startup disk. Perfect! And the only one offered is my drive (even has it custom icon). I choose that and recovery tells me it's "About to boot 10.9.1 from Mr. Harddrive".
...and then I get the flashing questionmark again, and Option-boot does not show that drive. Oh, I tried resetting the PROM at some point, too.
Right now I've got that machine booted from an external drive which happens to have OS X on it. I can fully access the system drive, all the data is intact, no problems at all. But I'd still like to, you know, be able to boot from it.
Anyone have any ideas?Here you go; the drive that I can't get too boot is /dev/disk3 (Mr SSD) but it looks like it's showing up as /dev/disk0 too?... I have no other 256GB drives in the system. I'm not sure why it's showing up like that and with slightly different sizes (maybe filevault?)
jethro1138@wyvern:/Users/jethro1138% diskutil list
/dev/disk0
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *256.1 GB disk0
1: EFI 209.7 MB disk0s1
2: Apple_CoreStorage 255.2 GB disk0s2
3: Apple_Boot Boot OS X 650.0 MB disk0s3
/dev/disk1
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *1.0 TB disk1
1: EFI 209.7 MB disk1s1
2: Apple_HFS Terry 999.2 GB disk1s2
3: Apple_Boot Recovery HD 784.2 MB disk1s3
/dev/disk2
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *500.1 GB disk2
1: EFI 209.7 MB disk2s1
2: Apple_HFS iMovies 499.8 GB disk2s2
/dev/disk3
#: TYPE NAME SIZE IDENTIFIER
0: Apple_HFS Mr SSD *254.9 GB disk3
jethro1138@wyvern:/Users/jethro1138% diskutil cs list
CoreStorage logical volume groups (1 found)
|
+-- Logical Volume Group 827A34E0-BE5D-4678-9B5A-B3DAAEA6985E
=========================================================
Name: Mr SSD
Status: Online
Size: 255200755712 B (255.2 GB)
Free Space: 16777216 B (16.8 MB)
|
+-< Physical Volume EFB59769-CF0A-4EC5-800A-22D7F2CB88C0
| ----------------------------------------------------
| Index: 0
| Disk: disk0s2
| Status: Online
| Size: 255200755712 B (255.2 GB)
|
+-> Logical Volume Family 6C64D757-9450-4FFF-A0E3-B46BFBCA367B
Encryption Status: Unlocked
Encryption Type: AES-XTS
Conversion Status: Complete
Conversion Direction: -none-
Has Encrypted Extents: Yes
Fully Secure: Yes
Passphrase Required: Yes
|
+-> Logical Volume 02280DA6-34C2-4205-A4C6-28D2B8669060
Disk: disk3
Status: Online
Size (Total): 254865207296 B (254.9 GB)
Size (Converted): -none-
Revertible: Yes (unlock and decryption required)
LV Name: Mr SSD
Volume Name: Mr SSD
Content Hint: Apple_HFS
jethro1138@wyvern:/Users/jethro1138% mount
/dev/disk1s2 on / (hfs, local, journaled)
devfs on /dev (devfs, local, nobrowse)
map -hosts on /net (autofs, nosuid, automounted, nobrowse)
map auto_home on /home (autofs, automounted, nobrowse)
localhost:/tQ3kz_0exBlmC1ciTfhsr0 on /Volumes/MobileBackups (mtmfs, nosuid, read-only, nobrowse)
/dev/disk2s2 on /Volumes/iMovies (hfs, local, nodev, nosuid, journaled, noowners)
/dev/disk3 on /Volumes/Mr SSD (hfs, local, journaled) -
Trying to pair IPAD2 with Windows 7 - Driver Not Found error
Hi, I have the Ipad2 & Iphone4 and am trying to pair them with my windows 7 pc.32 bit I get an error message that the bluetooth periphal driver is not installed nor can it be found. I have wifi but not 3G on Ipad2. I have 3G on Iphone 4 and my laptop can use the iphone4 3G to connect to internet if my comcast goes down. I do have the capability to use my 3G service of my Iphone to tether to my Ipad2. I do not understand why I am getting this bluetooth error nor can I find a way to resolve.
After searching through this forrow i found this
http://support.microsoft.com/kb/946414
After running the Fix-It, i had no problem installing iTunes -
Getting the Adapter Class Not Found Error in the Java Manipulator
Hi,
I wrote a custom java manipulator for the baseline update and created a jar file for the class. This works fine in the Windows machine. All I have to do is while specifying the CLASSPATH, I entered the ./ib/newManipulator.jar; ./lib/additional_dependency.jar. When I tried to deploy the same code in the Unix environment, it fails saying the Adapter Class not found. The only difference from windows and Unix environment is that in the windows machine, in order to run the base line update, I go to the directory my_project->control->baseline_update.bat but in case of Unix environment I have a separate location where I have a shell script called run-baseline-update.sh located at /apps/bin which invokes the baseline.sh in the directory my_project/control/baseline.sh. I even tried to put the full path of the jar files e.g. /my_project/lib/newManipulator.jar; /my_project/lib/additional_dependency.jar in the class path but still the same issue. Any suggestions?Unix classpath needs ":" as the path separator, not ";". Changing that will make this work.
For reference, later versions of the deployment template make this configurable, so you'd see (in environment.properties):
# PATH_SEP_VARNAME: for platform-independence
PATH_SEP_VARNAME=;
# Forge needs record store libraries as well as Spring to load record store adapter configuration files
FORGE_CLASSPATH=./config/lib/java/spring-delegate-adapter-1.0.1.jar${PATH_SEP_VARNAME}./config/lib/java/spring.jar${PATH_SEP_VARNAME}./config/lib/java/eacToolkit.jar${PATH_SEP_VARNAME}./config/script${PATH_SEP_VARNAME}.
You can then add the following to your <forge /> definition in AppConfig.xml:
<arg>--javaClasspath</arg>
<arg>${FORGE_CLASSPATH}</arg>
Hope this helps.
Michael -
File not found error generated when i try to fill a file
Hi,
I try to fill a file with data come from SQL SERVER table. I got the following error:
7000 : null : java.sql.SQLException: File \\bonnie\FraisMission/FraisMission.txt was not found
java.sql.SQLException: File \\bonnie\FraisMission/FraisMission.txt was not found
at com.sunopsis.jdbc.driver.file.u.a(u.java)
at com.sunopsis.jdbc.driver.file.d.h.c.a(c.java)
at com.sunopsis.jdbc.driver.file.g.a(g.java)
at com.sunopsis.jdbc.driver.file.g.a(g.java)
at com.sunopsis.jdbc.driver.file.w.executeBatch(w.java)
at com.sunopsis.sql.SnpsQuery.executeBatch(SnpsQuery.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.execCollOrders(SnpSessTaskSql.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTaskTrt(SnpSessTaskSql.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSqlI.treatTaskTrt(SnpSessTaskSqlI.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java)
at com.sunopsis.dwg.cmd.DwgCommandSession.treatCommand(DwgCommandSession.java)
at com.sunopsis.dwg.cmd.DwgCommandBase.execute(DwgCommandBase.java)
at com.sunopsis.dwg.cmd.e.i(e.java)
at com.sunopsis.dwg.cmd.g.y(g.java)
at com.sunopsis.dwg.cmd.e.run(e.java)
at java.lang.Thread.run(Unknown Source)
Yet The file i try to fill exists. I use IKM SQL To File Append.
Somebody can help me please?
Thanksin the ressource name box of your file model, when you push the search button ("...") do you see the file ?
Cause the problem can occur when you write directly the path without selectionning the file with the assistant.
Try this.
I think too that that you can't see the data by right clicking and selectionning View Data ?
Let me know the avancement... -
Internet Explorer returns "Page not found error" with new laptop set up
I have a recently acquired Dell Latitude D600 with TrueMobile 1300 Wireless adapter running XP Pro Service Pack 2 and a BEFW11S4 Version 3 Wireless router. I can get the router and laptop to communicate to the point of retrieving an IP address and show that there is Excellent Signal. How ever when I launch IE i get the Page Not Found screen. Once or twice i've been able to connect to the Google Home Page, but it seems random.
I have used the ping command in a DOS window to ping yahoo.com and google.com. Most of the time I get a 50% or less successful ping. I have directly connected the laptop to the router and it works without problem and I have another computer running Home XP via a WPC11 adapter that I have been using for many years.
Anyone have any experience with this symptom or problem?hi , here is what u do , hardwire the PC to the router first....access the router using http://192.168.1.1 "admin" is the default passowrd.....go to the wireless section and ensure u have selected channel 11....save settings....then go to the advanced wireless settings and reduce the RTS and fragmentation threshold by 40 each....save settings....
Maybe you are looking for
-
I see many discussion about transferring between two different computers but not one with just one computer. My husband and I use one Macbook, have two iTunes accounts and want to share some recently imported music.
-
Firefox is already running but is not responding... I get this error ten times a day or more!
I love Firefox and don't want to use a different browser, but the error "Firefox is already running but is not responding" is driving me crazy. The reason I get this error is because I frequently use http shortcuts from my desktop or click links from
-
Class Not Found Error in JDeveloper with Applet
HI Gentlemen, I have to set up an applet for my project using JDeveloper. I created an ADF application with Model and View projects, where the Model project has a very simple Applet and a HTML page to call it. The whole thing is located in ..\mywork\
-
JDeveloper 10g JSP, Struts and ADF application. I am developing a search form that has a number of criteria fields one of which is a selectlist. The code that is generated when I drop the data control as a single select list onto the jsp page is as f
-
When I write in Freehand mode, How do I erase a portion of what I have written? I cannot find how to turn my stylus into an eraser.