Why do I get a low wifi strength on IPad 3?

Guys,
I have recently bought an IPad 3 and get shocking signal strength on Wifi, using IPhone and PC on same router with no problem.   I have even installed a second router to increase signal range and the IPad locks up when connected to the second router, iPhone and laptop switch seamlessly between the 2!
Any ideas, very tempted to take the IPad back but bought it overseas so not that simple!
Jointly

Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Similar Messages

  • How to increase wifi strength for iPad Air

    How can I increase wifi strength to iPad from public wifi

    Not all will apple to public wifi.
    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at
    http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are drooping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Fix WiFi Issue for iOS 7
    http://ipadnerds.com/fix-wifi-issue-ios-7/
    iOS 6 Wifi Problems/Fixes
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    iPad: Issues connecting to Wi-Fi networks
    http://support.apple.com/kb/ts3304
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.hmL
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Signal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    10 Ways to Boost Your Wireless Signal
    http://www.pcmag.com/article2/0,2817,2372811,00.asp
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
    You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Why can't iPod connect to wifi network when iPad and Macbook can?

    Why can't my iPod connect to wifi network when iPad and Macbook both can? Connected in the past, but not for the past week.

    - Reset the iPOd. Nothing will be lost.
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears
    - Power off andthen back on the router
    - Power off and then back on the router.
    - Reset network settings>Settings>General>Reset>Reset Network Settings
    iOS: Troubleshooting Wi-Fi networks and connections

  • Idea Tab S5000 low wifi strength compared to other devices

    I'm quite happy with my new S5000 but the device looses wifi connection in many areas of my house where other devices have good signal strength. I updated all firmware and tagged wifi/battery optimization off.
    However compared to S4 mini and 5 year old Galaxy S1 the signal strength of the Lenovo device (measured by Wifi analyser) is 15 to 20db less than with these Android devices. What do I do wrong?
    link to pic
    Link to pic
    Mod edit:  Converted oversize pic to link per forum rule:  50k size limit on pic.

    Same problem here, it's really patchy on 4.2. Furthermore, my and a friend's S5000s actually keep turning the wifi of on its own seemingly randomly. Very annoying.

  • Why do I get such low bandwidth using buffered encoder reads?

    I have a PXI system with 10 6115 A/D boards and a 6608 timing board. I can do a simultaneous buffered AI at 5 MHz across all 40 channels of the 6115's.
    However, I can only do a single buffered encoder read at about 100 kHz.
    Why such a huge difference in bandwidth?

    I think the difference in bandwidth here is really due to size of the FIFO's present on each device. The 6115 has either a 16 or 32 Mega-Sample FIFO for analog input. If one of the 6115's isn't granted usage of the bus for a "large" amount of time, it can absorb this by backlogging the data into its FIFO until it is granted the bus, at which time the DMA controller will move the data to host memory before the FIFO overflows. The same is not true of the counters on the 6608. Each counter on the 6608 has an effective FIFO size of 2 Samples. This means at high sampling rates, the 6608 cannot withstand "large" amounts of time without being granted usage of the bus. How fast you can go before the counter FIFO overflows is going to be system dependent, but 200 KHz is in line with results I have observed. If you need to go faster, you can use two counter measurement methods, but you will sacrifice accuracy for speed. For example, by dividing down your input signal by 4, you will be able to go 4 times as fast, but your accuracy will also decrease by a factor of 4. You'll have to weigh the requirements of your application to determine if this type of trade off is acceptable.

  • Hi, why am i getting someone elses email on my ipad

    hi, i am receiving someone elses email in my yahoo account. can anyone help me to change this so i dont receive this other persons email thanks

    Is it real email or spam?
    Robert

  • Very low signal strength when using DLINK 2640t with mac mini

    i have a mac mini and i have been using it fine with a 2wire wireless modem. However i have just switched to a Dlink 2640t (54Mbps (802.11g) Wireless ADSL 2/2+ Router with Built-in Modem, 4-port 10/100Mbps Switch) and have been getting very low signal strengths on my mac mini, resulting in me not being able to surf the internet. The modem+ router is located in the next room. Does anyone know whether its the problem with the modem router or mac mini's airport wireless problems with the router itself. It worked perfectly fine with my previous 2wire wireless modem
    please help!

    Did you reset the router after you updated router's firmware? Its always recommended to perform a reset after firmware upgrade on the router.
    Please refer to the link http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=eaa3127db5f4402584c959a7251e754c_4008.xml&pid=80&r...
    For wireless range and signal issues, try changing the channel on the router to either 1,6,9 or 11.
    Please refer to this link on changing wireless channel and SSID (network name)
    http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=a0fb6c64337e47eb9e3e1027f364e70c_154.xml&pid=80&re...

  • Why can't I log into WiFI?

    Why can't I log into WiFi with my Ipad Air all of a sudden?
    WiFi is turned on.
    Under settings ... it shows the network Im trying to log into ... and in the column   to the right where it lists the various networks, it shows the network i want and a little wheel thingie spinning beside it ... but it just keeps spinning ... so it looks like my Ipad had found the network ok, but wont log in.
    Any thoughts?
    Under HTTP proxy ... ive got it set to auto ... is this correct?
    Everything worked fine until today so maybe Ive altered some setting without realizing it.

    Try this:
    1. Turn router off for 30 seconds and on again
    2. Settings>General>Reset>Reset Network Settings
    3. Reset iPad; hold the Sleep and Home button down until you see the Apple Logo

  • HT1694 Why am a getting duplicate emails to my hotmail account?

    Why am I getting duplicate hotmail messages on my iPad?

    Do you see duplicates if you setup mail on your computer? This will help isolate the problem a bit, to find out if it's just with the iPad.
    And, what server settings are you using for your hotmail account? Don't include the username/password or email address.

  • Why is it when I use WiFi I get better Youtube video quality than on 3G?

    Topic. And does WiFi use up more juice than 3G then?

    If you are connected to WiFi, no data will be transmitted over the 3G antenna. Leaving it on will consume a very small amount of additional power relative to turning it off (where it will default to the EDGE network). But, it's minimal additional drain. If you do get a call, 3G can be better (voice and data are carried on the same network), since 3G performs better at low signal strength because it uses signals from multiple towers simultaneously.
    Personally, I leave 3G on all the time, and have no issues with battery life (I do recharge nightly).

  • When using Lightroom Book module for Blurb book making, why do I keep getting a low image quality message if it's supposedly accessing my large raw files in my library?

    When using Lightroom Book module for Blurb book making, why do I keep getting a low image quality message if it's supposedly accessing my large raw files in my library?

    I think I've solved my problem with a Google Search. I came across a free slide show generator
    (contributions requested) that shows much higher quality slide shows than either iPhoto or Aperture 3.
    You click on a folder of jpegs and it almost immediately generates thumbnails and within a few seconds
    I can be viewing a full screen, tack sharp, slideshow of all of the files in the folder. Much sharper than
    I'm used to seeing.
    I think I'll keep the Aperture 3 and use if for the purpose it's intended for in the future. I'll also redo the
    image preview files to the small size it started with and then I'll copy all of the files I'm interested in from
    iPhoto into a separate folder on another disk. I'll use Aperture to catalog and to perform image manipulations
    on but I won't try to use it as an iPhoto replacement. I don't think I'll be using iPhoto much as an image
    viewer in the future either after I finish moving my favorite pictures to the Phoenix Slides folder.
    The name of the free program is Phoenix Slides. It's free to download and try, free to keep (though I
    think you'd want to pay the small amount requested) and fast. My pictures have never looked so good
    before.
    http://blyt.net/phxslides/
    Message was edited by: Jimbo2001

  • When I want to get on my wifi I tap my wifi in settings but it just loads and says unable to connect. It wont let me sign in. All my family's apple products are working. Why is this happening?

    When I want to get on my wifi I tap my wifi in settings but it just loads and says unable to connect. It wont let me sign in. All my family's apple products are working. Why is this happening?

    Try the following to rule out a software problem:                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • Why do i get a window in the lower right corner of the screen that says "high memory usage"

    why do I get a window in the lower right corner of the screen that says "high memory usage" on my compaq presario using windows xp home edition?

    Hi,
    No just turn the monitor off, not the product off. Which version of NIS are you using ? Please see the following screen:
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • I have cs4 master and I want to get creative cloud which it says you can get for lower price if you have cs3 or higher but it says i can't why?

    I have cs4 master and I want to get creative cloud which it says you can get for lower price if you have cs3 or higher but it says i can't why?

    Hi Quinn7,
    Was the one which you were upgrading from a Educational version? If so, that might be related. I'd recommend reaching out to our support for assistance. I think there is a link for chat or phone on the bottom of the plans page: Creative Cloud pricing and membership plans | Adobe Creative Cloud
    - Dave

  • Why IPhone is getting hot when downloading via wifi and how to turn off itunes 11.1 launch automatically when plugged in Iphone to the PC

    Why IPhone is getting hot when downloading via wifi and how to turn off itunes 11.1 launch automatically when plugged in Iphone to the PC

    My brother with the iPhone 4 suffers from that too.
    My iphone 5 doesnt however.
    But to Stop Launch when your apple device is connected, 1. connect your iPhoneto your computer, 2.Go to the Summary Page, 3. uncheck the box "Open iTunes when this iPhone is connected" and then your good for that device.

Maybe you are looking for