Why do I get an error 10612 when trying to readback from a line on an output port of a PCi-6527?

I am configuring the port (Port 3) as all outputs (even though it is not software configurable, I wanted to get a Task ID for it the first time that I use it). I can set the bit OK using a Port Write, but then when I follow that with a Port Read, I get the 10612 error. The manual says you can readback from the port, and the data that I'm getting seems correct, yet I still get that error. Is this normal, or is there a better way to implement this. I'm just getting started on my first project, and these simple things are frustrating.
Thanks.

The 10612 error code that you are receiving is not actually an error but a warning. The NI-DAQ Function Reference Manual for DIG_In_Prt states that if you call this function on an output port that has readback capability, +10612 will be returned along with the state of the output port. Apparently, this information was not included in the LabVIEW On-line Help. Generally, you can ignore this warning.
Regards,
Erin

Similar Messages

  • Why am I getting an error message when trying to use a template?

    Why am I getting an error message when trying to use a Pages template?

    You are getting an error message because there is an error.
    Knowing wht version of Pages you are using, what template you are attempting to open, and what error message Pages is sending you might help determine why you are getting that specific rror message. Without those, the first sentence above i pretty much all that can be said with any assurance.
    Regards,
    Barry

  • Why do I get "generic error" message when trying to upload a self-created, 1hr .wmv file?

    I went through the forums and made sure that any blocks or copywrites weren't triggered by the file, it's clean and can be opened using a media player and other video editing software like windows MovieMaker. I keep getting "The importer reported a generic error" message and have no idea how to proceed. Can someone please help?

    Re: Why do I get "generic error" message when trying to upload a self-created, 1hr .wmv  file?
    This ARTICLE starts with a checklist on setting up a computer to run PrE best, then goes into a series of links for tuning up one's computer and OS, and then links on troubleshooting.
    There is also a link on posting all necessary info, to help others help you.
    Without knowing much more about your system, it is impossible to say much beyond that WMV's are tough assests to work with, requiring a lot of CPU horsepower.
    Good luck,
    Hunt

  • Why do i get an error 8003 when trying to download apps for my IPAD?

    why do i get an error 8003 when trying to download apps for my IPAD?

    There's some advice on that one in the "Error -50," "-5000," "8003," "8008," or "-42023" section of the Specific Conditions and Alert Messages: (Mac OS X / Windows) section of the following document:
    iTunes: Advanced iTunes Store troubleshooting

  • HT5701 why do I get 3072 error code when trying to download 6.0.4

    why do i get 3072 error code when trying ot download 6.0.4

    Some details, please?
    Based on the version number, you seeking to upgrade Safari?
    What OS X version?
    How are you upgraded or downloading the software?   (Directly downloaded, or via Software Update?)
    Have you tried quitting all applications, and then performing the Software Update?   (Discussion per this thread — but that thread is for iTunes, and I'm guessing you're looking at Safari here?)  If that doesn't work, I'd keep everything quit, reboot, and try again.

  • Getting an error message when trying to export from the Lightroom 5.7.1

    hi
    i'm getting an error message when trying to export the images from the Lightroom, all the images are on the external drive
    i'm using windows 7 with 4gb of ram core i5
    "AN INTERNAL ERROR HAS OCCURRED WIN32 API ERROR2 ("THE SYSTEM CANNOT FIND THE FILE SPECIFIED.")WHEN CALLING SHELLEXECUTEXW FROM AGWORKSPACE.SHELLEXECUTE"

    i found the answer my myself
    post processing was blank that was causing it  to happen

  • Why do I get an error message when trying to Extrude and Bevel my image?

    I am making a logo for a friend and he wants something similar to the Stark House symbol. (The Direwolf) but as a dragon instead. I used the pen tool to make the shape, and now I want to fill it in and make it more 3D. I can't fill it in properly and my image gets an error message when I try to Extrude and Bevel. Why is this?

    error message,
    Is the path/shape closed?
    Selecting it and Ctrl/Cmd+J should close it if not, then you may try again.
    You may also have a look in the Document Infor palette with Objects ticked in the flyout and the path selected.

  • Why am I getting an error message when trying to replace existing music on itunes

    How do I stop the error message from showing up when I try to replace existing music on my iTunes?

    You are getting an error message because there is an error.
    Knowing wht version of Pages you are using, what template you are attempting to open, and what error message Pages is sending you might help determine why you are getting that specific rror message. Without those, the first sentence above i pretty much all that can be said with any assurance.
    Regards,
    Barry

  • Why am I getting an error message when trying to download iOS 6.0.1?

    Given that iOS 6 and 6.0.1 have been out for a good few days now, why am I still getting an error message?  Is it simply a case of keep trying??

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Why am I getting an error message when trying to burn my CD collection to iTunes.

    The message "Error occurred while converting the file (song title). The required disk cannot be found".
    Only two particular CDs were affected with this error message while all the rest were ok. I'm burning them via an Apple USB SuperDrive onto my MacBook Air. The CDs in question are Flight of the Conchords and Goldie Lookin Chain (if that makes one iota of difference). Does anyone have any suggestions?

    You are getting an error message because there is an error.
    Knowing wht version of Pages you are using, what template you are attempting to open, and what error message Pages is sending you might help determine why you are getting that specific rror message. Without those, the first sentence above i pretty much all that can be said with any assurance.
    Regards,
    Barry

  • Why do I get an Error Message when trying to "External link" an SWC?

    hi.
    when I use the "external link" option in the SCW linckage
    dialog box, the running SWF produces an alert box saying :
    "VerifyError: Error #1014: Class mx.core::Application could
    not be found.
    at flash.display::MovieClip/gotoAndStop()
    at
    mx.managers::SystemManager/::preloader_initProgressHandler()
    at
    flash.events::EventDispatcher/flash.events:EventDispatcher::dispatchEventFunction()
    at flash.events::EventDispatcher/dispatchEvent()
    at mx.preloaders::Preloader/::timerHandler()
    at flash.utils::Timer/flash.utils:Timer::_timerDispatch()
    at flash.utils::Timer/flash.utils:Timer::tick()
    I did what the documentation said, still I get that error...
    ..quoting the "Using flex builder 2" doc:
    "To set the SWC file as an external library file:
    With a project selected in the Navigator view, select Project
    > Properties > Flex Build Path.
    Select the Library tab, and then select and expand the SWC
    file entry to display the SWC options.
    Double-click the Link Type option. The Library Path Items
    Options dialog box appears.
    Select the External option, and click OK. "
    Anty suggestions?
    thanks,
    Guy.

    error message,
    Is the path/shape closed?
    Selecting it and Ctrl/Cmd+J should close it if not, then you may try again.
    You may also have a look in the Document Infor palette with Objects ticked in the flyout and the path selected.

  • Why do I get an Error 7 when trying to install iTunes 12?

    iTunes 11 worked great; however, when I try to install iTunes 12, I get an error message that states that Apple Mobile has not started correctly.

    Hi Linda,
    If you are having an issue with installing iTunes on your Windows computer, I would suggest that you troubleshoot using the steps in this article - 
    If you can't install or update iTunes for Windows - Apple Support
    Thanks for using Apple Support Communities.
    Sincerely,
    Brett L 

  • Why do I get an error message when trying to open PE 8.0 projects with PE9.0?

    I am trying to open a project in PE 9.0 that I made with PE 8.0. Each time, and with different projects, I get this error message:
    "Projects created with Adobe Premiere Pro and Adobe Premiere Elements are not compatible. Please use apropriate application to open this project."
    I have never used Adobe Premiere Pro nor is in installed on my computer! I updated my PE 8.0 with the patch that came out last year.
    My Operating System is Windows XP Pro, Service Pack  3, system specs are SATA 2 RAID 1 with dual 1 TB hard drives. 4 GB RAM. I have an Intel Core2  processor Q6600 (2.4 Ghz, 1066 FSB) with Quad Core technology and 8 MB cache, 4  GB DDR2 SDRAM at 800 MHz.
    My hard drive has been defragmented and have 779 GB or 83 percent free space.

    Can you create a test Project in PrE 9 and does that work. If so, close that Project and then Open it again in PrE 9.
    It could be as simple as your PrE 8 Projects just not Opening in PrE 9. There is often forward compatibility, but not always. It is usually best to finish Projects in the version, in which they were started.
    Good luck,
    Hunt

  • Why am I getting this error message when trying email a PDF?Server Connection Error. Please verify that port 143 is available for connection on your machine or contact your administrator.

    My Inspector for my house sent me his report via PDF that I had to access from an online link. I downloaded it but cannot forward it in an email to my insurance company who is requiring a copy. I get this error report every time:
    Server Connection Error. Please verify that port 143 is available for connection on your machine or contact your administrator.
    I have no idea what this means. Can someone help? I really don't want to have to print and scan this beast but I've been messing with this for 2 days now and am out of ideas.
    Thanks!

    I'm having the same issue.  Did you resolve it?

  • Why do I get an error message when trying to publish animate deployment package?

    I continually get the following error message every time I try to publish an animate deployment package.  I have no idea what Poster3.png is.  There is no image in my file with that name.  I have tried saving my composition under a new name and it doesn't resolve the issue.  I have no idea how to fix this.

    You may get this error if you had done the following:
    - create a comp and save it
    - publish to OEM
    - delete the poster in file system
    - publish again
    Workaround:
    Go to the composition click on stage and generate a poster image from the properties panel.
    Now publish again.
    Let me know if this works.
    -Sujai

Maybe you are looking for

  • At selection screen output not responding

    Hi ppl, I've 4 selection options in my screen. however I just need user to insert only 1 of the 4 for searching. Therefore i included 4 radio buttons. when user select <i>rbf</i>, <i>sfileno</i> will activer and other 3 will be grayed out, when user

  • Error when building documentation

    This issue was sent to me via e-mail by a colleague: Question iReport Development No.1 - Report Build error by Eclipse -Issue: When we build using build-release, a build error is being thrown. -Situation: Concerning this error, we think that "externa

  • Open form in a stacked canvas

    Hello all, I have a content canvas which has a stacked canvas on it. the content canvas i want to use as background and there will be buttons to navigate through different forms and have those forms called on the stacked canvas. Can u please tell me

  • In realtime when  and all " ALERTS"  will be created?

    All Experts         I am XI learner and can any one explain me in realtime scenario         when and we will creats Alerts ?         (How will notify by mail /sms/......the alert ?)         i.e :  Even for simple secnario's also is it required?      

  • Google Chrome messes with my DNS on Yosemite

    So I've spent ages today trying to figure this out. I have a nicely upgraded version of Yosemite. All was working well but I couldn't figure out how to make safari full screen without the toolbar (like a kiosk/presentation mode). It was suggested I u