Why does my airport utility always ask me to connect an ethernet cable when I would like to use the extended network option?

Please locate the model number on the side of the AirPort Express. Hard to see.....gray lettering on a white background....so you may likely need a magnifying glass and good lighting to see it.
The model number starts with a "A" followed by four numbers. If you see A1084 or A1088, unfortunately AirPort Utility 6.x in Mavericks OS X (10.9.4) does not support these older models. However, you can still administer these models if you have a Mac.....or can borrow one for a few minutes....using Leopard (10.5.x) or Snow Leopard (10.6.x), or a PC with AirPort Utility installed on the device.

Similar Messages

I want to re-use my old airport express base station but airport utility doesn't recognise it anymore (it dates from 2005) i would like to use it to connect to my speakers only

I have an old airport express base station from 2005
I would like to have a network on it so i can put it upstairs in a room and connect my speakers to it so i can send my music (from itunes) over the airport to my speakers.
I reset it and now i want to configure but the Airport utility doesn't recognise it anymore.
Can i update the firmware? has it become useless because too old or what can i do?
I work on macbook pro with macOSX 10.9.4
Can someone give me some tips please
thanks
J

Please locate the model number on the side of the AirPort Express. Hard to see.....gray lettering on a white background....so you may likely need a magnifying glass and good lighting to see it.
The model number starts with a "A" followed by four numbers. If you see A1084 or A1088, unfortunately AirPort Utility 6.x in Mavericks OS X (10.9.4) does not support these older models. However, you can still administer these models if you have a Mac.....or can borrow one for a few minutes....using Leopard (10.5.x) or Snow Leopard (10.6.x), or a PC with AirPort Utility installed on the device.

I have an airport extreme 2013. Why does my airport utility sometimes display IP addresses and other times the names of the devices? I want it to always display the device names.

I have an airport extreme 2013. Why does my airport utility sometimes display IP addresses and other times the names of the devices? I want it to always display the device names.

The utility has had less and less useful information .. it might be time to simply find a different utility.
Fing network scanner. iphone and ipad.
https://itunes.apple.com/au/app/fing-network-scanner/id430921107?mt=8
This is very popular.. I do not know of what works well on Mac OS because i have installed 5.6 utility which of course has far more info than the later toy version. Plus using an Asus router which has excellent listing of all the clients.
Sometimes beating yourself up to make apple routers do what you want is easier solved with lateral thinking.

Why does creative cloud is still asking serial number after i purchase and it wouldn't let me use it anymore because my trial is over need help NOW PLZ

why does creative cloud is still asking serial number after i purchase and it wouldn't let me use it anymore because my trial is over need help NOW PLZ

Hi There,
Kindly try the following steps:
Sign out and sign in to Creative Cloud app: Sign out, Sign in | Creative Cloud Desktop app
Sign in, activation, or connection errors | CS5.5 and later
Thanks.
Atul Saini

HT2693 Why does my Ipad keep telling me that my security code is incorrect when i am trying to update the billing information?

Why does my Ipad keep telling me that my security code is incorrect when i am trying to update the billing information?

It might be because the billing address you provided doesn't exactly match your bank records. It has to match your statement exactly. See http://support.apple.com/kb/TS1646.

I would like to use the VoiceOver utility application to only speak the words i type in TextEdit-to speak nothing else. can it be configured to do this? thanks.

i would like to use the VoiceOver utility application to only speak the words i type in TextEdit-to speak nothing else. can it be configured to do this? i would like to use it as a substitute for my voice. thanks.

Please locate the model number on the side of the AirPort Express. Hard to see.....gray lettering on a white background....so you may likely need a magnifying glass and good lighting to see it.
The model number starts with a "A" followed by four numbers. If you see A1084 or A1088, unfortunately AirPort Utility 6.x in Mavericks OS X (10.9.4) does not support these older models. However, you can still administer these models if you have a Mac.....or can borrow one for a few minutes....using Leopard (10.5.x) or Snow Leopard (10.6.x), or a PC with AirPort Utility installed on the device.

How do I turn off the alt scroll zoom? When I'm in Adobe photoshop and illustrator using the pen tool, alt is utilized for another short cut. I would like to use the alt command for the pen tool instead of zooming into the screen.

How do I turn off the alt scroll zoom?
When I'm in Adobe photoshop and illustrator using the pen tool, alt is utilized for another short cut. I would like to use the alt command for the pen tool instead of zooming into the screen.

I tend to select things from left to right and every time I am moving in a downward right diagonal motion during lasso selection I am missing a clear view and I am tending to have a more sloppy selection. All this does is slow me down since I need to go back and hit those areas again. The big arrowhead just get's in the way. The original lasso tool with the thin line and small active point at it's lower left was far better for me.
I don't like turning the cursors to precise because I like to see the active tool icon where my cursor is and as the icon changes as I hold modifier keys down. If I am forced to get comfortable with using pricise cursors I guess I will, but man, I've never had to do this in my 15 years of photoshop use...
I would absolutely LOVE to find a way to get the old lasso icon -- without the arrowhead above it.
Is there any chance this option could be inlcuded in cursor preferences? I'd give much thanks, Adobe.

Acouple of days ago I kept losing connectivity with the internet.By resetting either my modem or Airport Extreme I could regain it for 10-30 min. when I would have to repeat the resetting.Since with Apple

A couple of days ago I kept losing connectivity with the internet.By resetting either my modem or Airport Extreme I could regain it for 10-30 min. when I would have to repeat the resetting.Since,with Apple & Apple store support & many hours of contact with them the problem keeps recurring

Edge has very clear restrictions, one being that you must have 6 months of clean payment history which you don't. Either wait until April 14, or good luck at Sprint.
I am unsure how it can be determined the payment mix up was the fault of CS, but regardless, the mix up was done. There can be any number of reasons why a payment could be missed without any fault on your part, however you are still the responsible party for the account and must live with the repercussions.

HT4259 Why does my Airport utility not have either an option to manually configure, or a box "to extend the network?"

I have Mac with Lion, with an AIrport Extreme wi-fi network. I am trying to configure a Airport (model A1264) to extend the network. I read the Apple article on how to configure an extended network. Unfortunately my Airport Utility seems to have none of the functionality mentioned in the article. The article states to choose manual configuration of the base station. I can find no such option in my Airport Utility. Secondly, it the article states to check "create a wireless network," which I can find, but then says to check box to "allow this network to be extended." No such option appears anywhere in my Airport Utility. Lastly, my Mac is not even recognizing the existence of the Airport Express. It does not even appear as a wireless device, nor does it appear in Airport Utility as an "Other Airport Base Stations. It does however continue to flash amber. Does anyone know what might be the problem?
Thanks,
bmarr

I read the Apple article on how to configure an extended network. Unfortunately my Airport Utility seems to have none of the functionality mentioned in the article.
The article was written a few years ago and Lion 10.7.4 was not around at the time.
I suggest that you download and install the full featured version of AirPort Utility 5.6 for Mac OS X Lion . I think you will find that it will track with the article (if it is the one that I think it is) very nicely.
You can keep both AirPort Utility 5.6 and AirPort Utility 6.0 on your Mac.

Why does Time Machine not work over wifi but only via ethernet cable ?

Hi everyone,
It's been some time I have this problem now.
The first time I backed up my mac within Time Capsule with time machine, I chose to use the ethernet cable because the gigabit connection is much faster than the wifi for the first back up, but now, any time I want to update this back up, I need to connect the cable, cause "Time Machine can not connect to the Drive I picked" over wifi.
This is so annoying. Does anyone have a similar issue ?
Any solution ?
When I got this "error" I can use Utility Airport and get full access to the drive, even in finder. The only thing that doesn't work is TimeMachine connecting to the drive, even if it is detected by TimeMachine itself.
Thanks.
Riccardo

Typical Yosemite.
I suggest a full reconfigure of the TC.
Follow this list..
No files are deleted on the TC doing this although you might have to repoint your laptop to the backup.
Note.. even if TM does connect it will say it is going to do a new backup.. it is only when it starts that it discovers the backup exists and increments it.
Start from a factory reset. No files are lost on the hard disk doing this.
Factory reset universal
Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
Setup the TC again.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg TCgen5 for basestation and and TCwifi wireless name.
If the issue is wireless use TC24ghz and TC5ghz with fixed channels as this also seems to help stop the nonsense. But this can be tried in the second round. ie plan on a first and second round of changes to fix this.. hopefully.. I will point out other steps that can be round2.
2. Use all passwords that also comply with 1. but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. If the TC is main router you can skip this point. This is only an issue when the TC is bridged.
Ensure the TC always takes the same IP address.. you will need to do this on the main router using dhcp reservation.. or a bit more complex setup using static IP in the TC. But this is important.. having IP drift all over the place when Yosemite cannot remember its own name for 5 min after a reboot makes for poor networking.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric.. but this change will mess up your TM backup.. so be prepared to do a new full backup. Sorry.. keep this one for second round if you want to avoid a new backup.
5. Mount the TC disk in the computer manually.
In Finder, Go, Connect to server from the top menu,
Type in SMB://192.168.0.254 (or whatever the TC ip is which you have now made static. As a router by default it is 10.0.1.1 and I encourage people to stick with that unless you know what you are doing).
You can use name.. SMB://TCgen5.local where you replace TCgen5 with your TC name.. local is the default domain of the TC and doesn't change.
However names are not so easy as IP address.. nor as reliable. At least not in Yosemite they aren't. The domain can also be an issue if you are not plugged or wireless directly to the TC.
6. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only. Do the same for ethernet if you use it.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
You might need to do some more work on the computer itself. eg Reset the PRAM.. has helped some people. Clean install of the OS is also helpful if you upgrade installed.
Tell us how you go.
Someone posted a solution.. See this thread.
Macbook can't find Time Capsule anymore
Start from the bottom and work up.. I have a list of good network practice changes but I have avoided Yosemites bug heaven.
Yosemite has serious DNS bug in the networking application.. here is the lets say more arcane method of fixing it by doing a network transplant from mavericks.
http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

HT2497 Why does my Airport Utility keep saying "Double NAT"error?

I had to add a new cable modem to my home network.
I keep getting a "Double NAT" error and my modem keeps the yellow light blinking.
What do I do?

It's almost a miracle that it was working at all.
Each wall will absorb on average, about 15-20% of the signal so after 4 walls...and a ceiling....which is typically 2-3 time thicker than a wall....there isn't going to much signal left to extend.
Try locating the Express no more than half the distance between the Time Capsule and the general area upstairs that needs more wireless coverage. Minimize obstructions in the signal path as much as possible.
If that does not help, we'll have to do some SNR measurements to see if what you are trying to do is even feasible.

Just set up my TC after not using it for a year. I've moved in that time, so naturally my IP address has changed. My question is, why does my airport utility still showing the old IP address?

And does this mean that my internet is still coming from the AT&T router, or from my TC?

Is the IP address 10.0.1.1?

Why does my iphone 5 always tell me to connect to iTunes and not turn on

On Monday my iPhone started to turn itself off so i plugged it in to the computer to update it. When I plugged it in iTunes told me to restore my phone so I did, now whenever I try and turn my phone on it wont go past the connect to itunes pictures and it says theres an unknown error or its unable to restore

Hi there davidson.,
You may find the troubleshooting steps in the article below helpful.
iOS: Unable to update or restore
http://support.apple.com/kb/ht1808
-Griff W.

Why does my airport express keep cutting out?

Why does my airport express keep cutting out?

I have a 1st gen Airport Express and use it to stream music from my PC, iPhone 4, iPad and iPod Touch. My Airport Express is connected to a Teac UD-H01 DAC via an optical cable which is connected to an amp and speakers. I had no problems at all with this set up until I upgraded the Airport Express firmware to 7.6.3. The sound then started to drop out frequently. To cut a long story short after various testing, the problem had to be the Airport Express. I called Apple support but they were not much help and couldn't fix the problem and said they would speak to engineering and phone back. While I was waiting I decided to have another go to find the problem and opened the airport utility and saw that there was an option to downgrade the firmware. At this point I realised that the problems started about the same time that I upgraded the firmware to 7.6.3 but didn't think at the time that Apple would release a firmware that didn't work. Anyway I downgraded to 7.6.1 and hey presto, everything worked again. A couple of days ago I noticed that firmware 7.6.4 was available and thought I'd give it a go, not good - same problem as 7.6.3. I've downgraded to 7.6.1 again and all is well. Hope this helps.

Why does my Airport Express say "self assigned IP address"? No IP address for the ethernet, and it is not connecting to my cable router any longer...

Why does my Airport Express say "self assigned IP address"? No IP address for the ethernet, and it is not connecting to my cable router any longer...

Some cable providers.....like mine, a well known company......seem to take anywhere from a few moments to sometimes up to 30 minutes to allow their equipment back at the cable company to fully reset and issue a new fresh connection.
So, it would not hurt to leave things powered down for 15-20 minutes or more when you perform the reset that John Galt suggests.

Why does my airport utility always ask me to connect an ethernet cable when I would like to use the extended network option?

Similar Messages

Maybe you are looking for