Why does my Ipod display a syncing message then eject itself without syncing?

I tried reseting my Ipod and reinstalling Itunes, neither of these fixed the problem

Do you have the enable disk use option ticked from under the iPod's Summary tab?  If not, go ahead and do so now as it should prevent your iPod from ejecting itself.
If you can't the iPod to remain iTunes long enough to enable this option, try manually forcing the iPod into Disk Mode first using the instructions in this Apple support document.
Putting iPod into Disk Mode
B-rock

Similar Messages

  • TS1373 my  5th generation ipod acts like it is going to sync and then "ejects" itself before even 1 song can be synced. It then doesnt recognize that it has been ejected and keeps the"do not disconnect" icon on the screen even after unplugging. What do I

    my  5th generation ipod acts like it is going to sync and then "ejects" itself before even 1 song can be synced. It then doesnt recognize that it has been ejected and keeps the"do not disconnect" icon on the screen even after unplugging. What do I do?  it also makes a lot of noise while connected to the computer.

    Is the camera damaged? Could be a hardware problem.
    Try:
    Close the Camera app in the multitasking bar, then try again.
    Restart/Reset/Restore your iPod. In that order.

  • Why does my iPod clock keep changing and then I can't access anything without connecting charger

    Recently my iPod keeps changing time. It's seems to be losing time. When this happens I can't access anything without connecting lead and turning it off briefly.

    Could the battery be dying?
    Have yu tried the standard fixes:
    - Reset:
    Reset iPod touch:  Press and hold the On/Off Sleep/Wake button and the Home
    button at the same time for at least ten seconds, until the Apple logo appears.
    - Restore the iPod from backup via iTunes
    - Restore the iPod to factory defaults/new iPod.

  • Why my ipodmy ipod displays do not disconnect and wont sync but can be restored?

    why my ipodmy ipod displays do not disconnect and wont sync but can be restored?

    If it is a problem than I have it too. Mine does the
    same as long as I don't stop the device via the
    little green arrow icon (USB manager) down by the
    clock.
    I never really need to use the Ipod when it is hooked
    into the PC because everything is done through
    iTunes. I just thought it said "do not disconnect"
    because it was associated with both iTunes and the PC
    as a hard disk.
    If I stop the device or "eject" the iPod, it goes
    from do not disconnect to the normal menu tree.
    So when you take the USB cable out of the iPod, it goes back to normal?
    If that's what you mean, mine does that too.
    It's just that I read that if you remove the USB cable from your iPod while it says 'do not disconnect', it can wipe all your music....

  • Why does my ipod cannot sync 20 GB of memory if it is 32 GB ipod?

    why does my ipod cannot sync 20 GB of memory if it is 32 GB ipod?

    The message is saying that it needs 5 GB more GB that what is available on the iPod.
    How many GB are free before you sync?

  • Why does my ipod turn off whe I try to access messages

    Why does my ipod turn off when I try to access my messages

    See my response to you other post. Posting twice only hinders

  • Why does my iPod Shuffle stop working after a few songs?

    I had my iPod Shuffle for about a month now and it's already causing me trouble.
    I would play a couple of songs, but when I go to change it, it stops working. I turn it off and on again only to have it take me back to where I started off at (e.g. Let's say I have 100 songs, I start at 50 and I get to 55 before it shuts off. When I turn it back on, it starts at 50 all over again). This process would happen over and over again with seemingly no end.
    So my question is, why does my iPod Shuffle stop working after a few songs and how can I fix it?
    I already tried using the iTunes troubleshooting guide, but nothing worked.
    Details -
    4th Generation
    I only use it at the gym or when I'm running
    I've only used the Apple products that came with it so far
           (e.g. charger, headphones, etc.)
    881 MB are still left
    Music stops randomly, no common number or pattern

    I had the same problem, I purchased a new ipod shuffle, followed the instructions but it would stop after a few songs and I would have to shut it off, wait and turn it back on and it would go back to the same song and then once again, after a few songs it would shut off. I returned the ipod and got another one, same thing happened. This is how I resolved the issue.
    1. open itunes, make sure its up to date, then connect your shuffle to your pc
    2.on the left of the itunes window, select your ipod, then at the top select music then check the sync box and select "selected playlists"
    3.then go back and click on your ipod on the left, a message will appear just select apply
    all of your music should be emptied from your ipod.
    4.delete all of your playlists on the left, this will not delete anything from your library. Delete the "purchased" playlist under itunes store on the left as well, once again this will not delete anything from your library
    5.There should be an arrow just in front of your ipod, click on this arrow and you should see your music file for the ipod appear, this should be the only file that you see, everything else should be deleted.
    6. go to your music library and check only the songs that you want to load into your ipod. Double click on each song to make sure that they all play.
    If you find a song that does not play you should be asked to authorize it, don't waste your time that did not solve the issue for me, instead cancel to authorize the song and then delete the song and move it to recycle bin. Once the song is deleted a cloud should appear, click on the cloud and download the song again, when done, make sure the song plays and that it is checked.
    7.After you have made sure that all of the songs play and are checked, click on your ipod once more, located to the left, check the box  "sync only checked songs" then from the top select music. In the music window select "sync music' and then select "entire music Library"
    8. Go back to the left and click on the arrow in front of your ipod, you should see the music file, click on the music file and you should see all of your music being loaded to your ipod.
    9. When all of the music is done loading, eject your ipod by clicking on the arrow located after the battery symbol where your ipod appears on the left
    10. Turn on your ipod and scroll through your songs to make sure that the problem is resolved.
    Not sure if all of this was necessary but it worked for me.

  • Why does my computer display a spring coloured wheel that stops me from doing anything

    Why does my computer display a spinning coloured wheel that stops me from doing anything, the only way to get rid is to switch off and reload...

    These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad and start typing the name.
    Step 1
    For this step, the title of the Console window should be All Messages. If it isn't, select
              SYSTEM LOG QUERIES ▹ All Messages
    from the log list on the left. If you don't see that list, select
              View ▹ Show Log List
    from the menu bar at the top of the screen.
    In the top right corner of the Console window, there's a search box labeled Filter. Initially the words "String Matching" are shown in that box. Enter "BOOT_TIME" (without the quotes.)
    Each message in the log begins with the date and time when it was entered. Select the BOOT_TIME log message that corresponds to the last boot time when you had the problem. Now clear the search box to reveal all messages. Select the ones logged before the boot, during the time something abnormal was happening. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
    For example, if the system was unresponsive or was failing to shut down for three minutes before you forced a restart, post the messages timestamped within three minutes before the boot time, not after. Please include the BOOT_TIME message at the end of the log extract—not at the beginning.
    If there are long runs of repeated messages, please post only one example of each. Don’t post many repetitions of the same message.
    When posting a log extract, be selective. A few dozen lines are almost always more than enough.
    Some private information, such as your name, may appear in the log. Anonymize before posting.
    Please don't indiscriminately dump thousands of lines from the log into this discussion.
    Please don't post screenshots of log messages—post the text.
    Step 2
    In the Console window, select
              DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
    (not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
              View ▹ Show Log List
    from the menu bar.
    There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A crash report has a name that begins with the name of the crashed process and ends in ".crash". A panic report has a name that begins with "Kernel" and ends in ".panic". A shutdown stall report has a name that ends in ".shutdownstall". Select the most recent of each, if any. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot. It's possible that none of these reports exists.
    I know the report is long, maybe several hundred lines. Please post all of it anyway.
    If you don't see any reports listed, but you know there was a crash or panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
    In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
    Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

  • Why does the iPod duplicate songs when updating my playlists?

    Why does the iPod duplicate songs when updating my playlists? Also, you cannot use the "show duplicate songs" feature on the iPod - I suppose that is because it is not supposed to duplicate songs on the iPod. But, if that is the case - why does it do it?

    Try resetting your iPod, press and hold the power and the home buttons together approximately 15 seconds until the Apple logo appears. If that does not work try going into Settings>General>Reset>Reset All Settings. If that does not work try connecting to you iTunes library via the cable and un-sync the library from your iPod then sync the library.  For the next 2 options backup your iPod first, then do a Restore iPod from backup, if that doesn't work... As a last resort Restore your iPod as New. I too had the red circle and square after updating to 7.0.4 the last resort fixed mine, others have reported doing all the above, all have had reports of fixing the problem and not fixing it. Give it a try, hopefully one of these works, Good luck.

  • Why does my Ipod not synchronize all playlists? Some get synchronized, others don't. Yet there is enough space available.

    Why does my Ipod not synchronize all playlists? Some get synchronized, others don't. Yet there is enough available space.

    The S.I. prefix Giga is used to mean both 1000x1000x1000 and 1024x1024x1024. Computer software typically uses the second version, but using the first number makes the same number of bytes appear bigger when expressed as Gb, so is favoured by hard drive manufactures.
    80Gb10 = 74.3Gb2
    It's a bit like specifying a quantity in gallons without saying whether they are US or Imperial gallons - everybody gets the same volume but one number will be bigger than the other. I could offer you a tank with 10 Imperial gallons of fuel in it - but if I tell you it's 12 US gallons it sounds like you're getting more for your money.
    Once the total size of your library exceeds the capacity of your device all you need to do is create some size limited playlists to determine what goes on the device. Don't sync all movies, sync one or two that you plan to watch soon. Likewise with TV Shows. Limit podcasts to unplayed episodes and finally create a music subset. What worked for me for some time was a smart playlist called Steve's Tunes defined as Playlist is Music and Playlist is not Exclude where Exclude was regular playlist that I would manually add to until Steve's Tunes was small enough to fit. These days I run an iPhone and have a number of smart playlists with ? Gb of most played, ? Gb of highly rated, ? Gb of recently added, ? Gb of essentials, ? Gb of unplayed etc. Each time I sync I get slightly updated selection without having to put any extra effort in.
    tt2

  • HT1320 why does my iPod classic freeze up when i plug it in to my computer

    why does my iPod classic freeze up when i plug it in to my computer

    It's not a "fix," actually.  If that is a 4th gen iPod connected using USB, you need to do what it says and plug it in to the white square power adapter that originally came with those models.  Later Apple power adapters should work; third-party adapters may or may not work.  It has something to do with voltage.  The USB connection to computer does not provide the required voltage (although it's obviously fine for normal syncing and charging).
    If that iPod is connected to a FireWire port, it apparently provides the required voltage, because that step does not come up during the Restore.  That model was a transition between iPod connecting to FireWire and connecting to USB.  Earlier models required FireWire.  Later models only used USB.
    If you don't have an adapter, and there is an Apple Store nearby, I guess you could take it to the store's Genius Bar.  I'm sure they have a power adapter there, to complete the Restore.  (Just don't let them re-do the Restore on a Mac, if you use a Windows PC. Different storage formatting.)

  • Why does my ipod touch keep freezing

    why does my ipod touch keep freezing

    Maybe:
    https://discussions.apple.com/message/23482925#23482925
    make sure you read through all of the relies since the last one seems to apply in your case.

  • Why does my IPod shuffle stop after a few hours playing on shuffle when it should go for days?

    Why does my IPod stop playing after a few hours on shuffle when it should play for days?

    A few possibilities...  (Each numbered item is a separate thing to check or try.)
    (1) What does the shuffle's light do when you connect it to USB?
    (2) If the docking cable plug is not fully inserted, it may not have a good connection for charging.  Make sure the docking cable plug is fully inserted into the shuffle's headphones jack, as shown in this document
    iPod shuffle (4th generation): Not seen in iTunes
    (3) If there are other USB devices connected to your computer at the same time, try disconnecting other devices (including USB hub) so that the shuffle is the only device connected to a direct USB port, to see if that makes a difference (you can leave standard USB keyboard/mouse connected if used).
    (4) If you have a USB power adapter (such as from an iPhone, iPad, or other device), that plugs into the wall outlet, as a test, connect the shuffle's docking cable to the adapter and connect the shuffle.  Does it change from a power adapter?
    (5) Some newer Windows PCs (if you use Windows and not a Mac) may have a "feature" that shuts off full power to the USB port when a connected storage device is no longer mounted by the system.  An iPod is a storage device, and after syncing, iTunes unmounts the iPod's disk (if you are using automatic syncing).  If Windows shuts off full power to the USB port, the battery cannot charge.  To see if this is the problem, does the iPod appear in iTunes when it is connected, even though the battery is not charging?  If it does, select the iPod in iTunes so that you see its Summary screen.  There is an option (checkbox) there for Enable disk use.  If it's not already checked, check that box and Apply.  Enabling disk use keeps the iPod's disk mounted continuously, so Windows will keep the USB port at full power (and the battery will charge).  If the iPod now charges, there may be a way to disable this "energy saver" feature in Control Panels, so that you can turn OFF Enable disk use.  NOTE:  When Enable disk use is turned ON, you need to Eject the iPod in iTunes before physically disconnecting it.

  • The first row behind the words,Why does not be displayed?

    The first row behind the words,Why does not be displayed?
    The first line of why will automatically fill?
    The File(IDcs6) [Link to know attack page removed by moderator]
    Message was edited by: Peter Spier

    Filedown has a nasty reputation in English-speaking countries - plenty of antivirus/antimalware apps block everything there by default, which is what Peter has done. It doesn't mean that your link is malicious, only that it's hosted somewhere that has been used to host malware in the past.
    I'm pretty sure, Peter, that there aren't any nonbreaking spaces there, because I'd wager that there aren't any spaces there at all. It's justified text, and the reasons why it will or will not break are sometimes obscure when using composers that aren't the J composer. Chinese text is usually entirely free of spaces, except in certain circumstances, usually involving European language inserted into Chinese text. Sometimes, for reasons I don't understand, InDesign will simply treat Chinese as if it were English, and only break at spots permissible in Euro languages. That's not the case here - it obviously breaks between two Chinese glyphs, so something else is up here.
    Which version of InDesign are you using? Are you keying the text directly into InDesign, or are you placing, or copying/pasting?
    If you're using an English version of InDesign, I would suggest trying to save your Chinese text as raw text or RTF and File -> Place that. If you choose RTF, try to mark it with Chinese language in your RTF editor (Word?) if possible.
    Is No Break applied anywhere in your text? You can check in the Story editor (Control/Command Y) to see what styles and formatting are applied.

  • Why does lightroom not display photos ?

    Hello,
    all of a sudden lightroom tells me "no photo selected " when I try to open a folder.All the folders are visible but the photos cannot be displayed.I am using lightroom 4.1
    The last editing was done less then 12 hours ago without any problems.
    Your help would be much appreciated.
    Thank you very much,
    1journey

    Thank you so much for your reply.I solved the problem after fretting over it for some time. A filter was not turned off and once I turned it off all was well. Live and learn.
    Thank you kindly ,
    nihonbashi
    Date: Sun, 10 Nov 2013 08:54:35 -0800
    From: [email protected]
    To: [email protected]
    Subject: why does lightroom not display photos ?
        Re: why does lightroom not display photos ?
        created by F. McLion in Photoshop Lightroom - View the full discussion
    Does it show an image count on the folders in the folder panel?
    What does show if you select a folder in library?
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5830261#5830261
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5830261#5830261
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5830261#5830261. In the Actions box on the right, click the Stop Email Notifications link.
               Start a new discussion in Photoshop Lightroom at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

Maybe you are looking for