Why does my ipod only show an apple and wont start up

Why does my Ipod only show an apple and wont do anything else>  And holding down the two buttons has done nothing!

Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

Similar Messages

  • Why does my iTunes only show iTunes U and podcast options

    Why does my iTunes only show iTunes U and podcast options at the bottom. I just want to be able to watch movies on my iPad :(
    Plus when I go to the videos app and tap go to iTunes Store I get a blue message that says "cannot connect to iTunes Store".
    Help please, very frustrated as I'm not at all tech savvy

    Check what you can buy in your country:
    http://support.apple.com/kb/ts3599

  • Why does Startup Manager only show Recovery HD and not my other drives like Macintosh HD and my USB drive?

    I'm not really sure what happened to my Mac but when I start it, it only shows Recovery HD and nothing else.  I tried re-installing Mountain Lion through my Apple ID but it states that I have not purchased it and will not let me proceed.  I have bought a usb drive that has Mountain Lion, since I cannot purchase it in the apple store, on it to install it from there but I cannot boot into my USB because it only shows "Recovery HD" in Startup Manager.  I would really appreciate some input from you all, thank you for your time in advance. 

    Either your drive is failing or has been corrupted. Please try the following. You cannot do the following unless you have purchased Lion or later. From your post that's not clear. Without knowing your exact model I cannot tell you what to do.
    Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
    Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu.
    Reinstall Lion, Mountain Lion, or Mavericks
    OS X Mavericks- Reinstall OS X
    OS X Mountain Lion- Reinstall OS X
    OS X Lion- Reinstall Mac OS X
        Note: You will need an active Internet connection. I suggest using Ethernet
                    if possible because it is three times faster than wireless.
    If your computer is a 2010 or earlier model, then you should be able to do the following:
    Reinstall OS X without erasing the drive
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.

  • TS1382 My ipod classic shows a x and wont start, can reboot but cant do anything elts

    hit the Menu and middle butten and reset it, but nothing else works.
    tried to hit play/pause and middle after apple logo, but that didnt work

    this happend to me with my old ipod
    just let it sit near a window where or anywhere the sun will heat it so the water evaporates then try it
    if not just take it to apple

  • Why does my ipod touch show up in iTunes then disappear?

    Why does my ipod touch show up in iTunes then disappear?  The computer seems to recognize it as a camera device, rather than a mass storage device.  Does this have anything to do with the problem?  When plugged in, a window pops up asking which photo program you'd like to use, and if you cancel, that's it.  Even if you try to open a photo program, and download your photos off of the ipod, it still won't show up in itunes.

    Have you had a chance to look at these troubleshooting pages? They may be of some help:
    iPod shows up in Windows but not in iTunes
    iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date

  • HT2731 why does my ipod keep saying your apple id has been disabled when i try to get a free app?

    Why does my ipod keep saying 'your apple ID has been disabled when i try to get a free app???

    If you rest it on your computer's iTunes then try logging out of your account on the iPod by tapping on your id in Settings > Store and then log back in and see if it then works.

  • Why is my ipod keep showing the charger and itune thing

    why is my ipod keep showing the charger and the itune thing

    Do you man the iTunes icon and USB cable icon?
    Or is the charging indicator show here:
    http://support.apple.com/kb/HT1435

  • HT4623 My Ipad turns on but it only shows the apple it wont open de window

    My Ipad turns on but it wont shoe the window it only shows the apple and stays there

    Peluso123-
    One thing you can try is to reset (reboot) your iPad.  Hold both the Home and Sleep buttons for several seconds until the Apple logo appears.  If the logo is already there, keep holding for at least 20 seconds.  Ignore the "Slide to power off" arrow if it appears.  If you are successful, the iPad will restart after a couple of minutes.  Resetting this way will not hurt anything, and sometimes clears up mysterious problems.
    If that does not work or help, see if this article helps:  <iOS:  Unable to Update or Restore>.
    Fred

  • Why does my ipod turn off by itself and then turn back on after up grading to ios 7

    why does my ipod turn off by itself and then back on after upgrading to ios 7

    Try the standard fixes:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup. See:                                 
    iOS: How to back up                                                                
    - Restore to factory settings/new iOS device.             
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar                                      

  • Why my ipodmy ipod displays do not disconnect and wont sync but can be restored?

    why my ipodmy ipod displays do not disconnect and wont sync but can be restored?

    If it is a problem than I have it too. Mine does the
    same as long as I don't stop the device via the
    little green arrow icon (USB manager) down by the
    clock.
    I never really need to use the Ipod when it is hooked
    into the PC because everything is done through
    iTunes. I just thought it said "do not disconnect"
    because it was associated with both iTunes and the PC
    as a hard disk.
    If I stop the device or "eject" the iPod, it goes
    from do not disconnect to the normal menu tree.
    So when you take the USB cable out of the iPod, it goes back to normal?
    If that's what you mean, mine does that too.
    It's just that I read that if you remove the USB cable from your iPod while it says 'do not disconnect', it can wipe all your music....

  • Ipod only showing the apple logo and will not do anything else. 1st GEN

    my ipod will only show the apple logo when plugged in to my computer i have a dell running xp but i have tried other computers and it will not do anything but show this symbol. my computer does not recognise that it is plugged in. ive tried the apple support fix-it but it does not do anything period. the buttons do not work when plugged in or not. the only thing it does is light up when plugged in. my other ipod works perfectly no problems so this leads me to believe that its not the computers i have used. just think the ipod has had it

    Mine did the same thing last week after trying to update it via wi-fi. I then spent 11 hours Sunday updating my itunes on the laptop then restoring my ipod. Now all it does is beep as if it is just plugged in and flash the white apple logo. It beeps constantly. My computer at first didn't recognize it, then it did but said I needed to unlock it,(since I can't get the home screen up, I can't.) and now it doesn't recognize it at all. I've tried both computers.

  • My ipod only shows the apple logo, and won't connect to my computer. what do i do?

    My ipod touch only shows the apple logo, and i can't connect it to my computer. when i connect it, it doesn't show up in my itunes, or even in my computer. I was updating an app last night, and it wouldnt work, and it shut off.

    If it is still charging using the adapter, let it charge for 10min, then connect in recovery mode, explained here:
    iOS: Unable to update or restore

  • TS1441 why does my ipod keep showing the itunes thing after I restored it three time what should I do please help!

    I need help why does my ipod keep saying connect to itunes,I have already restored it 7 times what to do now.HELP ME!

    If the restores were successful, that is completed all steps without errors then:
    Restore loop (being prompted to restore again after a restore successfully completes)
    Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .

  • Please help me!My Ipod only show the Apple Logo :(

    Yesterday,when i use my Ipod,i was reset it,but when the logo Apple show again,it can not go to the Menu so i was plug it to AC Adapter and put it into Disk Mode but when i plug it to my PC ,the Ipod was show the Apple Logo(not in disk mode)So what i need do to restore my IPOD????Please help me!:(

    have you tried this
    http://docs.info.apple.com/article.html?artnum=61584

  • Update the iPad 2 with new iOS uppgrade, but after the screen only show the apple and nothing else. has been the case since yesterday. have turned off the iPad and turned it on again many times, but still only apple shown. What should I do?

    UPdate the iPad wjith new iOS upgrade that where shown under settings on the iPad, but after I did the upgrade the screen has only shown the apple and I can't get back. This has been the case since yesterday. Have turned off t.he iPad many times, but every timebwkhen Ibturn it on again the screen onöy show the apple icon and nothing else happends. What should I do? Anyone having the same problem and how can this be solved?

    Did you try to connect in recovery mode, explained in this article?
    iOS: Unable to update or restore

Maybe you are looking for

  • Report to show all superiors of an employee

    Dear Group members, My client wants a report to show all the hierarchial superiors of an employee. For eg- his  superior,his next superior and so on to to the chief officer. Is there any report for this scenario

  • Safari crashes upon open on Mac OS X lion 10.7.4. Here is the problem report, please Help!!! Thank you!

    Process:     Safari [793] Path:        /Applications/Safari.app/Contents/MacOS/Safari Identifier:  com.apple.Safari Version:     5.1.6 (7534.56.5) Build Info:  WebBrowser-7534056005000000~6 Code Type:   X86-64 (Native) Parent Process:  launchd [304]

  • How to import videos from iPhone 4 to PC?

    I'm trying to get a video that I recorded and edited with my iPhone 4 and iMovie, on my PC so I can share it with others. It won't email because the file size is too big (but the video is only 1:20...) and I uploaded it to YouTube but they removed th

  • ColumnChart - display number of items per time interval

    I have a collection of objects. Each object has a "time" property of type Date. I need to display a ColumnChart which shows one column representing the number of objects in a time interval. For example if I had 5 objects: 2 have a "time" of 3:00:00 1

  • Writeback issue

    Hi, i'm implementing writeback functionality. I have a table with an update button. Clicking on i update table with modification made by users on records. My table contains also a flag column. If user insert YES, it means that modifications are accep