Why doesn't my pc connect to apple ipad via USB cable
Connected my ipad to my pc via USB cable. Pc does not. Connect with it. under Computer device does not appear. My other external devices are ok though it recognises them ok I e external hard drive
What can I co to find out fault. It worked once before when I copied photos across from ipad to pc ok
If the iPad does not show up in My Computer when you first connect it (and also open the Windows "what do you want to do with this drive" box) then unplug the USB cable, wait 10 secs, then plug it back in.
If you don't hear the Windows "ker-plunk" sound then the drivers are not loading and you need to uninstall and re-install iTunes. The drivers that allow your computer to see the iPad are NOT built into Windows, they come with iTunes. Uninstall iTunes, go to the website and download and install the latest version.
Similar Messages
-
i have att u verse modem and it wi fi was not working. So i got net gear wi fi and connected to att modem . i connected my apple TV via Ethernet cable to att uverse modem . i did not want slow down my wi fi speed. My Apple phone is on Netgear wifi .Now airplay is not working .
Make sure that the Att Modem goes to the netgear router via ethernet cable. Then connect your Apple Tv with a ethernet cable to the back of the net gear router. Airplay wants it to both be connected to the same device, usually.
-
Morning, is it possible to connect your apple Ipad via bluetooth with a blackberry phone?
Morning, is it possible to connect your apple Ipad via bluetooth with a blackberry phone?
Lastly can you download from a wwindows computer to your Apple Ipad?No.
You can use iTunes on a PC to sync content to an iPad. -
I am trying to update firmware on my canon printer MG5320 to be able to use the airprint feature but in doesn't recognize the printer being plugged in via USB cable. I have tried restarting the macbook, turning on and off the printer, repairing permissions, deleting and redownloading the update what else can I do? The prinyrt works fine otherwise...
If there are no drivers for Yosemite you might be in trouble.. HP will tend not to support printers once they are EOL.
Getting it running over wireless rather than USB might be worthwhile.
Can’t connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
Has the printer been working and now failed after update.. what update caused the failure if that is the problem?? -
My brand new Xperia Z2 won't connect to the PC via USB cable.
My PC is running XP 64bit OS, my old Xperia U connects fine through the same USB cable and my Xperia Z2 recognizes flash drives connected to it via the supplied adaptor cable... Any ideas guys? does the phone perhaps not like my old version of windows?
Hi Jake, thanks for the response.I gave your suggestions a go and found that restarting the PC with the phone already connected via USB caused the phone to briefly flash up "connected to computer" in the notifications bar.This occured immediately on start-up of the PC, during motherboard Bios, and dissapeared as soon as windows began to boot up. Upon windows starting, no mention of the phone is found anywhere under "my computer", device manager or in the task bar... More on the issue...the very first time i connected the phone to the PC, the computer was already running. The phone immediately asked me if i wanted to install PC Companion 2.1. Following the installation, the connection just went and hasn't come back since. I have noticed that PC Companion will not start on my PC. I've tried re-installing it several times from Sony website but when i try to run it I just get an hourglass for 5-10 seconds, then nothing. checking back through the system requirements for Pc Companion I've noticed that it asks for every OS except mine (XP 64bit)... could this be the problem with the software not running and perhaps the phone not being recognised?
-
My ipad is not charging while connected to any device via usb cable
my ipad is not charging while connected to any device via usb cable
If you mean that you've connected it to a computer's USB port then a lot of computers don't provide enough power to their USB ports to charge the iPad at a sufficient rate - it may still be charging slowly, and should be a bit quicker if the iPad's screen is off (if you leave it for a while and then disconnect it from your computer you may find that it's battery percentage has gone up). The wall charger is usually the most efficient way to charge the iPad.
-
Why doesn't my iPhone connect to tv? Keeps saying "this accessory is not supported by this iphone"
Why doesn't my iPhone connect to tv? Keeps saying "this accessory is not supported by this iphone"
I assume you are running ios 8.x. It's a bug.
Wait for a fix from apple. ... OR ... You could buy a new Apple brand connector. The latest connectors will work, even the older apple brand connectors do not work. OR try re-booting your ipad. OR wait until the video starts then attach the connector.
more info here:
Re: 30 pin to VGA adapter won't work since iOS 8
unable to use HDMI adapter after iOS 8.0 upgrade -
how do I connect my new (purchased last week) macbook air to my samsung smart tv? I purchased the adapter at the apple store and connected to the TV via HDMI cable. The TV says "no signal. I do not see TV as an option in the display tab of system preferences. what else do I need to do?
First, make sure your TV is tuned to display the correct input signal. Most TVs have several inputs (multiple HDMIs, cable connections, RCA etc) so double-check that you're using the correct one - HDMI1, HDMI2 or whatever is written next to the port.
I assume that you have a mini-Displayport to HDMI adaptor? If you open displays preferences, first tick the box that says "show display preferences in menu bar" then locate the menu and click Detect Displays. See if that helps.
Matt -
My apple tv3, serial no. C07JWBZ9DRHN is not powering on. Connected with Computer, with micro USB cable with power on, it is not shown in Devices. How to rectify
You have to remove all cables before connecting to your computer with micro usb. Power is only connected when using a 3rd gen device and done after the initial connection.
http://support.apple.com/kb/HT4367?viewlocale=en_US&locale=en_US -
Why doesn't my imbedded video play on iPad?
Why doesn't my imbedded video play on iPad?
Is it running flash? Because the iPad 2 does not run flash. Or it could be a bug in the embeded video. Run the debugger and see if that helps. Good luck :-)
-
My Ipod classic 160gb is dead,It only responds when I plug it in to cpu via usb cable then the screen blinks.When I try to reset it the Apple logo appears but the apple logo blinks on and off to as long as i hold the buttons down,when i realease the reset buttons it just blinks back and fourth to the blank gray screen,it worked fine yesterday night this morning its tanked.is this unit completely dead or can something be done at home?
Thank you for your help
IceI wrote this long time ago, have a read and see whether it can be soloved
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/itunes/download/
For old and other versions of iPod updater for window you can get here
http://www.ipodwizard.net/showthread.php?t=7369
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iTunes 7 and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921�
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ or ifixit at your own risk
http://www.ipodresq.com/index.php
http://www.ifixit.com/
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
Exclamation point and folder and nothing else
Spank your iPod
http://www.youtube.com/watch?v=3ljPhrFUaOY
http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevant_history/2004/11/meeting_the_sad.html#comment -10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
Cant put it into disk mode
http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
I think my iPod just died its final death
http://discussions.apple.com/thread.jspa?messageID=3813051
Apple logo & monochrome battery stay
http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
My iPod ism’t resetting and isn’t being read by my computer
http://discussions.apple.com/thread.jspa?messageID=4489387#4489387
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote -
IPod touch frozen on screen showing apple symbol and usb cable.
Pod touch frozen on screen showing apple symbol and usb cable. Happened during a update attempt.
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
Finally, if the Restore doesn't work, let the battery drain completely. Then recharge for at least an hour and Restore again. -
Macbook Pro suddenly will not connect to the internet via ethernet cable.
I know this is a long shot... but I figured I would give it a try.
My macbook pro suddenly does not connect to the internet via ethernet cable. Please bear with me, as I am not very tech-savvy - I will try my best to describe the symptoms!
I connect to the internet via ethernet (we don't have wifi). It was working before I went to work, and when I came home I suddenly couldn't get anything to work (I know everyone says this, but I truly didn't mess with anything). Internet browsers just think for awhile and then turn up the 'You are not connected to the internet' error.
I went into my network preferences and curiously, the 'Ethernet' shows a green dot and says 'connected'. However it says 'Authentication server is not responding' underneath the last part that says '802.1X: WPA: eduroam' (I think that is my user profile).
When I go into my 'security' settings I can see that my firewall is off, so that shouldn't be causing any problems.
I've tried restarting the router and computer itself many times. Diagnostics just gets to a certain point and reports back 'Network Diagnostics cannot fix the current networking problems.' I've also tried switching to a different ethernet cable, and I tried both cables out on a PC laptop and it connected without issue. Additionally, I brought my macbook along to a friend's house and it connected to his wifi just fine, so the problem appears to just be with ethernet connections.
I know it's hard to troubleshoot this kind of thing without being there and having a look at the computer yourself, but any tips wouild be greatly appreciated.As I mentioned above, I am not very tech savvy so I have no idea why a wireless protocol would be showing up there, I'm just listing everything I see in hopes that someone might know something I can try. This is why I am asking for help here - I'm not sure what has happened that has made me unable to connect, especially since it seemingly occured while nobody was using the computer.
I guess I should clarify that I'm not a total hillbilly- normally my firewall is set to 'on', but I set it to 'off' to try and troubleshoot the issues here as I was told that sometimes it can interfere with the computer's ability to connect to the internet. If this is not the case and firewall does not affect anything, I will turn it back on while I try to fix this.
I have tried the method you mentioned above a few times - I actually contacted my ISP earlier this week and they recommended resetting the router like that. They didn't mention any known network issues. -
Dear Community,
how can I connect SCSI tape recorder via USB to iMac ?
Is there any adapter/converter on the market now ?
Cheers, MarekThanks Jan.
Actually the reason to use Quantum SCSI tape recorder is to back-up big amount of data (propriety movies footage) both on PC (what is quite easy, using SCSII host adapter with VHDCI 68 connector) and iMac what seems to be not easy. All my search by Google leads to that conclussion, they finished production of SCSI-to-USB or FireWire because somebody stopped to produce chips to covert protocols. So even buying noe second-hand adapter, no guaranty it's still working with Lion (nobody is developing drivers anymore). Strange is, nobody or just a few are using SCSII (Ultra 320) devices (while the transfer is not bad, 320 MBps what is 2560 Mbps, so the only limitation is tape recording (some 80 MBps) not an interface. Using compression mode I can (and I do) record 1,6 TB of footage data. However quite slow, is safe and cheap, comparing with any HD storage solution. USB 2 is much more limited.
I'm using Time Capsule for buck-up. But even 3 TB one day will be full of data, then old back-ups will be eaten by new once, what is not good idea for archives. I'm using another 2TB NAS HD (2x2TB RAID 1), but this is also going to be full soon.
Of course, you are right, the option is another machine (OSX,Win,Linux or Solaris) equipped with SCSII controller. But this requires another machine, just for back-up time to time, and in practice iMac folders must be shared with that small auxiliary machine because amount of data practically excluding even temporary data collection on auxiliary machine. And it must be transfer by wire, not WIFI, my only network. Tape recording is in my case really good, professional solution, isn't it?
Anyway, if somebody has similar requirements as me, and found the solution for SCSI, please let me know. So far, follow Jan's idea, I'm thinking about some embeded mini PC, fanless, equipped with slot for SCSI, with SOME smart system on-board, to deal with iMac for type recording. The option is previous Apple model, but to be honest, I became Mac/OSX user 4 years ago. I fell in love with Mac, but my knowledge about previous models is based on Google....
My desk becomes full of boxes. Do you know how big Quantum TC-L42BX is ? Is very big. And now another box.....another keyboard....another screen... And one small adapter could solve the problem. Eh....
Best regards,
Marek -
I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?
Not without a player..
The AE is a dumb file server.. the hard disk you plug in is an even dumber hard disk.
There are no smarts in this setup.. not even DLNA. So the TV would have to be an extremely smart one to read raw files on a network drive.. none do that I know of.
A solution is WD live TV.. it can read files from just about any file source on network and play them to the TV.
Nothing apple makes will do that.. ATV is a streamer not a media player. Everything in the Apple world is tied up with itunes. So you must have a computer running itunes to use it.
You can download a more generic player for ipad, and put that as part of the network.. but you still need ATV to display the video.
Maybe you are looking for
-
Deleting music album
-
Convert date/time to Unix epoch
I have thousands of date time stamps I would like to convert to Unix epoch ten-digit strings. That is, take some thing like: Dec 9, 2005 10:24 AM and convert to 1234567890 (only in the correct unix epoch time) What formula can I use? I've found that
-
MacBook/Macbook Pro and Final Cut Studio
I am about to buy a Mac, but im not sure if I should get the MacBook or MacBook Pro? Which is better suited for Final Cut Studio? Is there a specific version of the MacBook/MacBook Pro that would be best? Thanks so much!
-
Specifying dot gain curves for custom CMYK profile
I am trying to create a custom CMYK profile that would mimic the FOGRA39 (coated) ICC profile but would provide more control. When creating a custom ICC profile, I'm trying to specify the dot gain curves manually by entering the Tonal Value Increase
-
Hi, I have implemented the badi REBD_PROPERTY tp ZREBD_PROPERTY. I need to implemented the method CHECK_ALL method IF_EX_REBD_PROPERTY~CHECK_ALL. endmethod. How can i import the data please? Thanks for your help and your reply. Spawnrad