Why doesnt the 3850 switch suport the 2702 AP?

Hi
I just found out the hard way the 3850 switch doesn't support the 2702AP. Does anyone know why cisco's latest switch doesn't support an up to date AP?
Anyone from cisco care to answer when it might if at all?
Regards

Hi,
Ryan is right, IOS-XE 3.6 added following AP support
Support is added to the following APs in this release:
AP2700I, AP2700E
AP1532I, AP1532E
Note The Cisco Aironet 1530 Series APs are supported operating only in Local mode; these APs in mesh mode are not supported.
AP702W, AP702I
If you are running this version of software & still cannot register your AP, then attache the AP console output to see what's the reason for failure.
HTH
Rasika
****Pls rate all useful responses ****

Similar Messages

HT4085 Why isn't "hold" an option for the side switch on the iPad?

Why isn't "hold" an option for the side switch on the iPad?
I'd like to be able to let my 3 year old watch videos on the iPad, but young kids want to touch the screen. I need a method to disable the touch screen. Seems simple, why isn't this an option?
Is there a way to write an app that allows the side switch to act as a "hold" switch?
Mark

mark915 wrote:
Why isn't "hold" an option for the side switch on the iPad?
I'd like to be able to let my 3 year old watch videos on the iPad, but young kids want to touch the screen. I need a method to disable the touch screen. Seems simple, why isn't this an option?
Is there a way to write an app that allows the side switch to act as a "hold" switch?
Mark
The obvious solution is to put the iPad screen out of his reach. Now that's innovative!

Help! I've just updated my iPhone 5 to iOS 6.1.2 and I can't find the LTE switch only the 3G one.

Help! I've just updated my iPhone 5 to iOS 6.1.2 and I can't find the LTE switch only the 3G one.
Settings > General > Cellular *I know that the LTE switch should replace the 3G one 'cause my mom has it
I updated it from iOS 6.0.2 I think so I skipped 6.1. Is this a possible reason (tho I doubt it)?
is there any way to fix this?
thank you in advance!

Are you using an LTE enabled SIM? What carrier are you using?

The ring switch and the volume botton do not work what is theproblem ?

The ring switch and the volume bottons do not work, what is the reason?

When you say they don't work, what are you trying to do? When you say the ring switch, I'm assuming you are referring to the mute switch that turns the ringer off/on? What troubleshooting have you tried?
The standard troubleshooting procedures for the iPhone are:
Power off/on
Reset
Restore, first from backup, then as a new phone.
IF that doesn't help, then you make an appointment at the nearest Apple Genius Bar and have them see if there is a hardware issue.

HT5622 iPad 3 and my sound has stopped from speakers, but can get from headphones. It's not the side switch and the volume is max in all areas. Anyone got any ideas, what problem is and how to fix it thanks

Hi,
My iPad has just stopped working with sound from the speakers, it works fine with the headphones in. The soft mute button is not made and the volume is at max.
Any ideas what problem is and how to sort. Thanks

System sounds can be muted from the software switch in the task bar as well as from the side switch depending on how you have it set up. This my boilerplate resonse for sound issues.
1. If you have no sound at all, even in the Music App, try rebooting the iPad.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
2. If you lost sounds for keyboard clicks, games or other apps, email notifications and other notifications, system sounds may have been muted.
System sounds can be muted and controlled two different ways. The screen lock rotation can be controlled in the same manner as well.
Settings>General>Use Side Switch to: Mute System sounds. If this option is selected, the switch on the side of the iPad above the volume rocker will mute system sounds.
If you choose Lock Screen Rotation, then the switch locks the screen. If the screen is locked, you will see a lock icon in the upper right corner next to the battery indicator gauge.
If you have the side switch set to lock screen rotation then the system sound control is in the task bar. Double tap the home button and in the task bar at the bottom, swipe all the way to the right. The speaker icon is all the way to the left. Tap on it and system sounds will return.
If you have the side switch set to mute system sounds, then the screen lock rotation can be accessed via the task bar in the same manner as described above.
This support article from Apple explains how the side switch works.
http://support.apple.com/kb/HT4085
3. If you still have no sound at all - except when using headphones ....try cleaning the dock connector opening of the iPad with a soft brush and just a little bit of rubbing alcohol.

Where is the wireless switch on the sony vaio 14e?

Where is the wireless switch on the sony vaio 14e? Wifi is connected. Signal strength good. Wlan enabled. No reason to not open but when try resetting connection only possible problem which appears is wireless switch is off, but I can not find a switch, buttonor icon anywhere. Please help!
Also before I could post I had to "choose a board" but the only one appearing is xperia tablet so that's not too helpful!

Hi karen260181,
Please provide us the exact model name of your unit so we can check the specs and provide accurate solutions. You can use this link as a guide to determine the model name of your unit. Thanks!

Just bought iPad gen3 the silence switch on the side doesn't work, it shows the symbol on screen but doesn't silence the iPad?????

Just bought iPad gen3 the silence switch on the side doesn't work, it shows the symbol on screen but doesn't silence the iPad?????

The Side Switch is to mute your ringers, and most of the application's sound. To totally mute the sound, you must use the rocker to mute it.

Why does Mission Control switch to the Desktop 1 without me issuing a command?

This happens to me constantly. I'll be working and not even touching the keyboard and Mission Control, without me doing ANYTHING switches me to Desktop 1. Can anyone tell me how to fix this?

I'm having the same issue. The only thing I can think is that there is something stealing focus back to the main screen. This didn't happen for me prior to upgrading to Mavericks.

Why doesnt X-Fi have on-the-fly AC3 encodi

I dont understand why Creative didnt add on-the-fly AC3 encoding on the X-Fi - considering the cost of the card, and 5million transistors? Surely it could at least be done in Software (drivers) with a bit of help from the CPU?
HDA X-Mystique 7. Gold is only a $80 sound card and has a C-Media 8768 8channel chip that encodes all audio (stereo, games, DVD's, etc..) in the PC to Dolby Digital 7. and outputs it as SPDIF - no analog inputs, no confusing DigitalDIN connectors. Just one optical connector
http://www.nvnews.net/reviews/x-mystique/
And considering all creative cards have major PCI Latency problems on various PC's (my SBLi've cuts out when passthroughing AC3 via Digital TV Tuner software, yet my onboard realtek AC97 chip works perfectly - changed the PCI latencies with no luck), I think I'm totally losing faith in Creatives workmanship Message Edited by Anarchi on 0-24-2005 0:50 PM

Partly because Creative have their heads up their rear ends when it comes to using a digital connection. They're more concerned with analog and do very little with the digital out which Dolby Digital Li've uses. I'm sure most are aware that only the advantage of using the digital out on a sound card and having speakers capable of decoding dd and dts is for movie watching.
Other activities will be limited to stereo which is fine for me I don't need my other speakers around me outputting the same thing. I will however be purchasing a set of speakers without a decoder next time probably Klipschs because I have horrible problems playing dvds in Windows XP MCE 05 with the digital out on(Logitech Z-680 decoding the dd or dts stream).
I didn't have the problems before with my SB Audigy 2 zs, but after responding to my email I sent Creative thinks it's MCE which is hogwash. FYI my problems are out of sync audio/video and glitchy audio when playing dvds I have to sometimes rewind or use the skip chapter button to correct the audio.

Everytime I click on a link or shortcut it opens a new tab, why doesnt it open it on the tab im on?????? it does it for everything!

Every time I press on a shortcut or a link it used to open them on the tab that I was on, but now it always opens a new tab for everything and it is making me mad.

Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
*Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
*Do NOT click the Reset button on the Safe Mode start window
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

Where is the wireless switch on the W500?

Hi
My wife just bought a Lenovo Thinkpad W 500 and she cannot access the internet via wireless capability. Is therte a wireless switch on the Thinkpad W500?
Thanks for your assistance
Garf
Solved!
Go to Solution.

Make sure it is on in the BIOS. Under "config", turn the radio on. Under "Security-I/O Port Access", make sure it is enabled.

Can't find the power switch on the Zen V P

I can't find the power switch on my 2GB Zen V Plus. The manual says it's right below the lock switch but I don't see anything below it. Am I totally missing something?Thanks

Hi Cat,?A complaint I have about the Zen V plus is the small size of the buttons. They are a bit too close together and too small. It's a little difficult to do things like push the middle toggle?back and forth or?push it down without hitting the other buttons or toggling too much. My ipod is a lot easier to navigate. Phil

If I delete a message using delete key, AND the "Find in this message" box is open, should the focus switch to the search box, or remain in the message list?

If the "Find in this message" search box has been left open, but I have selected a message in the message pane, if I use the delete key to delete the current message, the focus moves to the "Find" box. It took me a while to figure out why the focus did not remain in the message list so I could delete the next message. I can regain the desired behavior by closing the search box, but it would be nice to not need to. This is on a Windows 7 OS. I should check to see how it behaves on a Linux box.

Hi,
for the Points
Sometime I think I would like it if I could delete an iMessage completely.
Other times when reading them on my iPhone I wish to leave them until I can answer them with something that is on my Mac.
It seems that as a device or a Mac that is off line can "catch up" on iMessages sent within a few hours would suggest that the iMessages are held on the server for a period.
It would be handy for different levels of "deletion".
7:19 PM Monday; February 11, 2013
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.2)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images."  No, Seriously

When I click on the Firefox icon, I get the TWCCentral page. However, the page is misaligned, i.e. all the pictures switch to the left leaving a white blank sp

pictures switch to the left leaving a white blank area on the left of the page. I contacted Time Warner and they told me you are the one to correct this problem...I hope you can...please let me know when
this situation is resolved...Thank you. [email protected]

I assume this page worked normally in Firefox 22?
Firefox 23 introduced a new security feature. If this is an HTTPS page, insecure content may be blocked. Look for a shield icon on the address bar to the left of the URL. This article has more details about this feature: [[How does content that isn't secure affect my safety?]]
If it's not a secure page or there's no shield, here is a more general suggestion.
When you have a problem with one particular site, a good "first thing to try" is clearing your Firefox cache and deleting your saved cookies for the site.
(1) Bypass Firefox's Cache
Use Ctrl+Shift+r to reload the page fresh from the server.
Alternately, you also can clear Firefox's cache completely using:
orange Firefox button (or Tools menu) > Options > Advanced
On the Network mini-tab > Cached Web Content : "Clear Now"
If you have a large hard drive, this might take a few minutes.
(2) Remove the site's cookies (save any pending work first). While viewing a page on the site, try either:
* right-click and choose View Page Info > Security > "View Cookies"
* Alt+t (open the classic Tools menu) > Page Info > Security > "View Cookies"
In the dialog that opens, you can remove the site's cookies individually.
Then try reloading the page. Does that help?

One of the four switches of the stack crashed

Hi,
I have a question, can You help me?
Symptoms: The switch hangs - after a hard reboot and after two hours switch No. 2 flew out from the stack. After the reboot, everything returned to normal and now when a few days passed switch works without problems.
Devices: WS-C3750X-24T-S
Best regards,
Marcin.

12.2(55)SE1??? You're stack is running this?
I'd agree with Paolo. Upgrade the IOS to 12.2(55)SE4 or 15.0(1)SE2.

Why doesnt the 3850 switch suport the 2702 AP?

Similar Messages

Maybe you are looking for