Why EIGRP metric didn't change after add delay?

Here is the lay out:
--R2--
E1---R1---E2/ \E3
--R3--
I have added delay for R2's E2 interface, but when I check the EIGRP topology from R1 for E3, the metric didn't change and they are still the same for R2 and R3.
Do I miss anything?

You've discovered that ascii diargams don't work on the forum. :-)
Remember that EIGRP always takes its metric from the inbound interface. In this case, R2 and R3 take their "connected metric" to E3, and advertise it to R1. R1 takes its delay from E2, and adds it to the delay R2 and R3 advertised. R2's metrics on E2 have no bearing or impact on R1's metric for E3.
R2's metric on E2 will have an impact on R2's cost to reach E1, however.... Always consider the direction the update is going, and then add cost on the inbound side of one of the hops if you want to traffic engineer, rather than the outbound side.
Russ.W

Similar Messages

PO- Why PO still allow to change after Delivery Completed has ticked.

Dear All,
I'm doing functional testing for MM, but i realised that the PO still allow to change after delivery completed has ticked.
Can i know if there is a way to restrict any change after any good receiving or delivery completed?
Thank you very much,
Regards,
Chee Wee

Hi,
Here we have same problem that after tick GR completed system allow to take further receipt though PO is not open.
we communicate with SAP and there is no function available to close the po for receipt until you reduce PO qty for GRN Qty or loca / delete line item.
We had write user exit to check tick in PO for GRN allow or not and that give error message.
You can do same for GRN.
Regards,
Chetan Mistry

Blank Rows in Table on Range Change After Add

I have a table and to add rows to it, you click on an add button, enter the information and then click save. After clicking save you return to the first page of the table. If you click on the Next option and change the table range, the table only shows the first record (in that new range) but the rest of the lines are all blank with no data. So for example, if my range is 5 and I have 8 records, after hitting the next button I see the 6th record and then 2 more rows but they are blank. How do I refresh the data after the range change to show the rest of the records properly? (Note, this appears to only happen after adding new records).

Since there is a sequence try this url, this will do the job:
see section "4.12.5 Assigning the Primary Key Value Using an Oracle Sequence"
http://download.oracle.com/docs/cd/E17904_01/web.1111/b31974/bcentities.htm#insertedID12

Product release Didn't Change After Applying Service Packs

I have applied Service Pack 2,3,4 Crystal XI. My product Version 11.0.0.1883 stayed the same even after applying t service packs. Would anyone have any ideas why it still shows the old release, nd thanks for helping with my issue.
Jim Dyer

Hi Jim,
Make sure you are the local PC admin and that DEP is disabled. I've seen this happen also and there were no warnings or errors, it just didn't update.
Try re-installing the patches from a local drive and be sure to turn DEP off. Search Forums for more info on how to.
Also, what OS are you installing on?
Thank you
Don

Why do adjustment brush parameters change after drawing?

Adjustment brush includes few "programm preset effects". When I start to use "Eris inhance", its parameters are set to 66. After drawing part of my picture, it automatucally decrease to 40. I do need every time to increase it again to 66 manually. I do not know why those parameters change and how to repair it (previously it was always set at the 66 level, even after drawing).
I use Lr 4.1 on Mac.
Actually parameters change just after I realease my mouse.

Adjustment brush includes few "programm preset effects". When I start to use "Eris inhance", its parameters are set to 66. After drawing part of my picture, it automatucally decrease to 40. I do need every time to increase it again to 66 manually. I do not know why those parameters change and how to repair it (previously it was always set at the 66 level, even after drawing).
I use Lr 4.1 on Mac.
Actually parameters change just after I realease my mouse.

Why the missing parts list changed after Pro.order released

I open a pro.order before released ,then I do the availability check get a missing parts list, this list including less parts than the missing parts after pro.order released ,why does it caused?which configuration caused?
Thanks,
Helai

Hi Lai,
You can do Material Availability check at the two stage of Production / Process Orders.
- First is to control (Check Missing Part) at the time of Order Creation.
T.code is OPJK - Select order type and Business Transaction -1 at the time of Order Creation
- Second is to control(Check Missing Part) at the of Order Relase.
T.code is OPJK - Select order type and Business Transaction - 2 at the time of Order release.
So it may possible that you have assign different checking group or checks to the above both stages , that's why you got different result regarding missing parts during above both stages.
Regards,
Dhaval

Why does LR4 show brightness changes after external processing in CS4?

I am an experienced user of Lightroom and get excellent results. But an anomaly is puzzling me. I capture images in DNG format and download to a PC Windows 7 using a calibrated Eizo graphics monitor. Before exporting and delivering a processed image I ensure that there is no unacceptable clipping showing on the histogram. I export 16 bit files which are only converted to 8 bits immediately prior to delivery. Recently I have adopted the procedure of importing a copy of the final delivery image back into LR4.3 for better library management. (There are often keyword changes or other refinements in the delivered image) Occasionally I notice that some pictures are noticeably brighter than the existing LR processed masters which formed the basis of the above operation. So I did some tests.
I selected an image with wide tonal range, adjusted it in Develop module to meet my 'no unacceptable clipping' rule and exported it as described above into CS4. My working colour space is Adobe RGB 1998 and Color Management is set to 'RGB Preserve Embedded Profiles'. In CS4 I only changed the mode from 16 to 8 bits and then saved the file using a modified name. That was the only processing done in CS4. Both files (8 bit and 16 bit) were then re-imported back into LR4 and the histograms compared with the original modified master file. In both cases they showed highlight clipping indicating that the image is brighter than when starting the final processing in CS4. In most cases the extra brightness is not a big problem; but in some instances it is quite unaccepable and I could not use that version without further processing in LR4. Mode change does not seem to be the culprit.
Can anyone help me to understand what I might be doing wrong to bring about these unwanted involuntary changes to normally processed files? Thank you.

What colorspace do you have configured in LR for your TIF Edit-In export to PS? Since PS is out-of-date with respect to LR, presumably you are using the Edit with LR Adjustments option not the Open Anyway option.
What happens if you don’t change to 8-bits in PS?
What happens if you merely export the TIF from LR and re-import it? With variations being: if the Export bit depth is 8 bits vs 16 bits and if the Export colorspace is ProPhotoRGB vs AdobeRGB?
Do you somehow have lens-profile corrections set as the default for TIF Imports or any non-zero Toning being applied on Import? The LR defaults for TIFs can be set independently from the defaults for raws.
What happens if you use ProPhotoRGB in your Edit-In export settings and as your working space in PS?
What happens to the histogram if you soft-proof to Adobe RGB in LR?
Is your monitor calibrated with a hardware calibrator? If so is the profile ICC V2 or ICC V4?

Why does the font rendering change after I publish to the web?

I created an animation in Edge Animate with four slides, using Open-Sans as the font. The font rendering looks good in Edge Animate and looks good in the local html version as well, but when I publish it to the website, the font formatting is not acceptable.
Here is the local HTML version:
Here is how it appears on the website:
Is there a way to control this better?
Thanks.

Hopefully someone else will be brave enough to respond to this, but in the meantime, the best solution I have found so far is to post the animation files to a separate directory on the server. Then pull that page in using an iframe. This way the animation is not influenced by the parent page's styling.

Why my cursor didn't change in Dreamweaver?

abbr:hover {
cursor: url(/images/aero_arrow_xl.cur), pointer;
The cursor aero_arrow_xl.cur is taken or copied from the cursor directory under the Windows folder.
The aero_arrow_xl.cur is not shown, instead the pointer is only shown.
And the same situation is in other cases, for example:
abbr:hover {
cursor: url(images/awesome.cur), url(images/awesome_cursor.png), pointer;
awesome.cur is not shown, nor awesome_cursor.png is not shown, instead the ponter is always shown.

Verify that your links are correct.
Your first example shows a site root relative link (with the leading /). Unless you have a local server set up, it won't function correctly when previewing in a browser.
Your second link example in bold looks correct but without being privvy to your folder structure and whether you are using the css in an external file. It's very hard to say.
Could you post a link to a page where it's not working.
Also, cursor images seem to be a bit "stickier" than a normal image in the browser cache. Make sure you clear your cache to preview them.
Finally, which browsers are you checking this in, some of the older ones have no support for custom cursor images.

Why does my session ID change actionResponse.sendRedirect()?

Any ideas why my session ID would change after executing actionResponse.sendRedirect(<insert absolute url to a page in the same application>)?
50% of the time my session id persists after sendRedirect(). The other 50% of the time the session id changes. This happens without making any changes to the application.
Any ideas are welcomed.

actionResponse.sendRedirect() supports 1)absolute URL and 2)full URI. try with full URI.
Apart from these,why do you need to do the redirection ? If requires that,you can do it very well using taskflow.
Regards,
Hoque

Change or add new domain and realm

Hi,
I'd like to change the default domain 'example.com'.
I have tried to change the values of DomainsAndRealms in the SipServletContainer of system MBean browser.
But this didn't change or add the value of Table ocmsuser.REALM, and the SIP UA got the message of 401 Unauthroized.
Could U help me?
Joshep.

pubCenter do not allow creating multiple ad-units with same name and the error you mentioned usually shown if given ad-unit name is duplicate, that is if there is an ad-unit with same name. Try to create ad-unit with a different unique name.

I just installed itunes 11.1.5.5. Now the format in Itunes is changed. when I am trying to add music to my iphone, there is no longer an add button under the Iphone device. Why did they have to change this? Can anyone help, Im tryiong to add music.

How do you add musci to the Iphone? I just installed itunes 11.1.5.5. Now the format in Itunes is changed. when I am trying to add music to my iphone, there is no longer an add button under the Iphone device. Why did they have to change this? Can anyone help, Im tryiong to add music.

Correct. When you purchase devices, they would have stated the OS they needed to work, on the box. This can be overlooked, but it is very important to check when purchasing.
You current OS, is so old, that they technology build into the new devices, is not something your OS understands. It didn't exist when your OS was created, and therefore you need to upgrade the OS to work with the newer technology of these devices.
10.6 software is not downloadable. You must purchase a DVD disc. You can order it from the on-line apple store
- http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard.

Can't figure out why colors don't totally change when you select type with curser? It looks like it has by looking at it, but when you highlight the area after the old color is still there. It happens with objects to. Driving me NUTZ. Help!

Can't figure out why colors don't totally change when you select type with curser? It looks like it has by looking at it, but when you highlight the area after the old color is still there. It happens with objects to. Driving me NUTZ. Help!

Select the text, and open the Appearance palette (Come on guys, text highlight is irrelevant, it happens to objects too says the OP), and see what's listed there. For a simple text object, there should only be a line item "Type", followed by "Characters", and when double-clicked the Characters line item expands to tell you the stroke and fill color. For a basic object, there should be a fill and/or stroke.
What happens sometimes, is that you end up adding extra strokes/fills to objects or text, and the appearance palette is where that will be noted. Especially when you are dealing with groups, and/or picking up a color with the eyedropper, you may inadvertently be adding a fill or stroke on top of something. You can drag those unwanted thingies from the Appearance palette into its own little trash can.

Why does the Iphone4 freeze up after downloading the IOS7.6 patch showing an ITUNE icon? The phone will not change screens for 4 hours.

Why does the Iphone4 freeze up after downloading the IOS7.6 patch showing an ITUNE icon? The phone will not change screens for 4 hours.
I Turn it off/on and nothing changes.

Hello bigboza,
Thank you for using Apple Support Communities.
For more information, take a look at:
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
If the device remains unresponsive or does not turn on (or power on), reset your device.
If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
Let it charge for at least twenty minutes, then see if it starts normally.
If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
If the screen displays a red battery icon, continue charging the device until the battery is fully charged. Learn more about charging iPhone and iPod touch, or iPad.
If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
Connect the device to your computer and open iTunes.
If the device appears in iTunes, select and click Restore on the Summary pane. Learn more aboutrestoring iOS software.
Have a nice day,
Mario

Add a context change after a set of values in a context

Dear experts,
My requirement is as follows:
Scenario: Idoc to Idoc. I need to check if there are line items > 5- I need to do a split. The split is happening properly via my mapping but I have a problem at the header record level on the target- I do not get the values populated correctly. I need to add a context change after 5 values in the queue.
eg:
Say there are 2 Idocs at the source with following unique IDs: called Journal ID:
My source:
Idoc 1: Journal ID 123
Line Itme 1
Line Item 2
Idoc 2: Journal ID 124
Line item 1
Line item 2
Line item 3
Line item 4
Line item 5
Line item 6
Line item 7
So I need to get total of three Idocs in my target:
Idoc 1: Journal Entry 123
Line Item 1
Line Item 2
Idoc2: Journal Entry 124
Line item 1
Line item 2
Line item 3
Line item 4
Line item 5
Idoc3: Journal entry 124
Line item 6(new 1)
Line item 7(new 2)
The split in the target Idoc is working perfectly. But inside the header record the journal ID field(taken from Item record level) is not populating correctly. I am getting this output:
Idoc 1: Journal Entry 123
Header Record-->JournalID Field value= '123'
Line Item 1
Line Item 2
Idoc2: Journal Entry 124
Header Record-->JournalID Field value= '124'
Line item 1
Line item 2
Line item 3
Line item 4
Line item 5
Idoc3: Journal entry 124
Header Record-->JournalID Field value= Null
Line item 6(new 1)
Line item 7(new 2)
So please suggest a UDF/standard function to populate the right values inside header record--->Journal ID field.Something like the below...
public void calculate(String[] var1, ResultList result, Container container) throws StreamTransformationException{
for ( int i = 0; i < var1.length; i++ )
if( var1[i].length() > 5) //here var1 I am passing the Journal ID
result.addContextChange();
Apparently this doesnt work.

The first Idoc has two line items and the second idoc has 7 line items. As the split is per 5 line item- the target has 3 Idocs.
Now the problem is that the header value in the target: REF_DOC_NO has to be created as per the number of line items and doesnt come from header record directly.

Why EIGRP metric didn't change after add delay?

Similar Messages

Maybe you are looking for