Why is SSD so slow on Satellite A300 PSAG8E

Guys hi,
Please help me on the following question. I would like an admin to help me plz, or a very experienced user, if this is possible.
2 weeks ago I bought an Satellite A300 PSAG8E. A couple of months ago before the purchase of this laptop, I had also bought an SSD OCZ 64 GB v2 core series drive. I tried several times to install the SSD on the laptop, but the response during windows installation and after during the use, the response of the drive is very, very slow. It is even slower than it is with its original 250 GB disk. I benchmarked the SSD with SISOFT SANDRA and confirmed my impression.
The SSD was rated 5400 rpm, strangely the same speed as the original 250 GB HD that comes with the machine.
I used different windows CD's (one with SP3, and one older version with SP2, both original windows) but nothing changed. I then installed my SSD on my desktop machine and the installation and use in windows environment, is blazingly fast. I put it back on the laptop and again it is very, very slow.
What is going on? Do you have any suggestions? Is there any bug with using SSD's on my model?
Is there any firmware upgrade?
I suspect this has something to do with Laptop's transfer rate. Can you help me please?
What can I do?
Kind Regards,
Dionisis Falireas

Dear Niko_1
thank you for your time, let me answer plz.
1) The SSD was rated by Sandra benchmarkng. I believe that what Sandra means is that according to its read and write measurements, the SDD is as fast as an 5400 drive. Which is not the case, because when i install it on my desktop is very very fast.
2) Imagine that while i had the ssd installed, i tried to copy 600mb (megabytes). The time it took was 16 minutes! Something is wrong.
3) Regarding what you said, about sata drivers. Which raid compatible driver should i install? I have browsed for days the internet, and i didnt see any forum saying that i should install raid drivers for the ssd. Probably you have a point, but shouldn't this be a common problem and everywhere on the internet, if this was teh case for an SSD to work?
4) Another point you may have is about the sata driver. You say that sp3 does not include sata drivers. Where can i find these sata drivers, to test it? because my original hard drive for toshiba, is SATA and as far as i know, winodws do recognize sata drivers. Can you clarify plz?

Similar Messages

  • Satellite A300 (PSAG8E) - Hardware problems after installing win7 ultimate

    Hello and good day,
    I've installed win7 ultimate a few days ago and windows managed to recognize most of my hardware accept my build in mic and camera and another component I am not sure about what it is (Windows update automatically downloaded the sound and graphics driver for me).
    My questions are - where can find the remaining drivers and where can I get the preinstalled Toshiba tools and software? (The driver site in the Toshiba support page does not include those drivers and software)
    Thank you very much
    Roi Ben Simon

    Hi
    I have Satellite A300 (PSAG8E) too and installed Win7 Home premium and everything works perfect.
    At first I must say that I don't know where you have searched drivers and Toshiba tools and utilities because all stuff is downloadable on Toshiba support & download page under http://eu.computers.toshiba-europe.com
    It is logic that mic will not work if you didn't installed proper driver. Install drivers alone and not using Microsoft update. What you need are real and tested drivers and not some free drivers from internet.
    Go to Toshiba download page and install all stuff following this installations order:
    -Win7
    -chipset driver
    -storage manager
    -display driver
    -sound driver
    -modem driver
    -supervisor utility
    -infrared
    -patches
    -configfree
    -VAP
    -toshiba hardware setup
    -HDMI control
    -WLAN driver
    Everything works well but missing some drivers
    Added Vista stuff:
    -Toshiba assist - work properly
    -Card reader - installed properly
    -Webcam driver for A500 - tested with Skype - work properly.
    -Synaptics driver

  • Satellite A300-PSAG8E - HDD indicator is blinking even when i do nothing

    these are my problems
    1. My HDD indicator is blinking even when i do nothing ( blinks every half second or so)
    2. When I go somewhere my display turns off and when I move my mouse display turns on but nothing is happening. Everything is standing still (sometimes 20 seconds, sometimes 2 or 3 minutes ) and than he is ready to work.
    Upgraded BIOS to version 2.20
    OS: Windows 7 Ultimate
    Laptop: Toshiba Satellite A300-PSAG8E
    Anyone know the solutions?
    Need help please! Thank you

    > 1. My HDD indicator is blinking even when i do nothing ( blinks every half second or so)
    Even if you dont touch the notebook, the HDD is running and different applications access the data. The applications and processes which are running in the background would cause this blinking. Note; this is not a problem!
    > 2. When I go somewhere my display turns off and when I move my mouse display turns on but nothing is happening. Everything is standing still (sometimes 20 seconds, sometimes 2 or 3 minutes ) and than he is ready to work.
    Disable the stand by modem and disable the settings which disable the screen while notebook is not in use. This can be done in Windows 7 power management.

  • Satellite A300 PSAG8E does not charge

    I have a Toshiba Satalite A300 PSAG8E which does not charge.
    I was handed it a few days ago by someone claiming that it doesn't work or turn on -- vague details.
    Upon receipt it turned on, asked whether to start windows normally or not, then booted absolutely fine, it powered from the mains charger, no problem.
    I left it on for a while doing various tasks.
    I came to it a few days later to find it had turned itself off.
    I powered up again, at which point it asked whether to start windows normally or not. I started normally and it came on fine.
    Since then I have been unable to power it from the mains.
    Why won't it charge now?

    Thanks for your responses so far. Much appreciated. Not to be rude guys, but I thought I was clear enough. However, I can understand the confusion as the situation is unusual.
    The problem is simple:
    When the laptop is plugged into the mains, the battery does not charge. The laptop does not power on. The situation is this: It only does this sometimes.
    What I have tried:
    Wiggling the cable, in all sorts of ways to see if there's a possible connection issue. This does not appear to be the issue. It seems to be simply on or off.
    I tried resetting BIOS to default before the battery went dead last time. Still no power.
    http://aps2.toshiba-tro.de/kb0/FAQ6201DK0004R01.htm
    # Make sure the battery has a full charge.
    - No, it has run flat since it charged last. Unable to recharge.
    # Try plugging the AC adapter into the computer.
    - Tried. Nothing.
    # Try plugging the AC adapter into a different outlet.
    - Tried. Nothing.
    # Try pressing the power switch for ten seconds.
    - Tried. Nothing.
    # Make sure the power switch is not physically locked off, like a cover protecting it.
    - Checked.
    # Try removing the battery and the AC adapter, then plug only the AC adapter in and try powering on.
    - Tried. Nothing.
    # Make sure you have the proper AC adapter, and only use the one that shipped with the computer.
    - Yes.
    # Is the computer turning on, but the display is blank or being routed to a monitor that you can't see? If so, try using the FN+F5 keys.
    - No. It is not and does not turn on.
    # If the computer is on, but no display or won't power off, you can press and hold the power button for ten seconds (until it powers off), then try powering on again.
    - No. It is not and does not turn on.
    # Make sure you remove all extra hard ware, especially extra memory even if it shipped that way from the dealer. The memory could be loose, or could have gone bad.
    - Checked. Nothing.
    # Look at the lights on the computer for clues. Are you getting AC power? Is a light blinking? If there is a blinking light it can be an indication that Power supply Micro controller detects an error. In this case please contact ASP (Authorized service partner) in your country.
    - No lights. When battery is in, battery light blinks when you press the power button because the battery is dead.
    What I will try next: Detach the battery and power cord overnight.
    If I manage to get it to power up, update BIOS.
    Any further advice?

  • Satellite A300 (PSAG8E) - What is new in BIOS 1.9?

    Hi,
    I have a A300 PSAG8E and I would like to know what news between BIOS 1.7 and 1.9?
    The new BIOS can change the fan control? On my A300 it is so loud.
    Thank's, regards, cricri975.

    Hi!
    Have you checked the Toshiba website if there is a change log available?
    Normally there you can check if its a change log available or not.
    http://eu.computers.toshiba-europe.com => Support & Downloads => Download Drivers
    If you cant find a change log on the Toshiba website there is no change log available. ;)
    Bye

  • Win7 on Satellite A300 - cannot get FN keys to work

    Hi every body
    I really need your help guys I really need FN keys job
    I recently formatted my Satellite A300 laptop with Windows 7 32bit and the function keys doesnt work. I downloaded VAP from your site also I tried downloading flash card utility from the other Toshiba types list.
    When I try to install it on my Toshiba it kept saying to me invalid serial no.
    Why is that >> also still FN keys doesnt work. Please help me. What should I do?
    Sometimes when I push FN+ brighten it works but nothing appears on my laptop as it used to when I had xp also I bought my Toshiba from UAE.

    Hello
    I have satellite A300 too and use it with Win7 32bit. Everything works perfectly. It is very important to install all drivers, tools and utilities following right installation order so here is the list how I have done this:
    Satellite A300 (PSAG8E) and clean Win7
    -Win7 (original Microsoft install disc)
    -chipset driver
    -storage manager
    -display driver
    -sound driver
    -modem driver
    -supervisor utility
    -infrared
    -patches
    -configfree
    -VAP
    -toshiba hardware setup
    -HDMI control
    -WLAN driver
    Everything works well but missing some drivers
    Added Vista stuff:
    -Toshiba assist - work properly
    -Card reader - installed properly
    -Webcam driver for A500 - tested with Skype - work properly.
    -Synaptics driver
    Win7 runs well and I am very satisfied with it.

  • Satellite A300-1JH PSAGLE: Control buttons don't work with XP

    Hello there.
    I own a Toshiba Satellite A300 psagle.
    It works beautifully, but there is a problem: the tactile music buttons don't work.
    I am using Windows XP and I have installed all the drivers available.
    Could some one please tell me what I should do.
    P.s. how can I activate the "face recognition" option?
    Please reply.
    Regards.

    Hi
    Regarding the Toshiba Control Media buttons;
    You have to install the Toshiba Controls from the Toshiba European driver page.
    Check there the Satellite A300 PSAG8E series and download the Toshiba Controls
    Regarding the face reorganization:
    Check these threads:
    http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=127846&#127846
    http://forums.computers.toshiba-europe.com/forums/message.jspa?messageID=131453
    Bye

  • Satellite A300 1lW - Windows 7 installation - any issues?

    Good Morning/afternoon!
    I would like to install a new intern hard drive on my laptop and I want to put also windows 7 on it.
    The issue is that it is the first time I will do this manipulation and I dont really know what sort of functionality will be incompatible with this installation.
    - Can you recommand me a windows 7 version which can be suitable for this laptop?
    - Which functionality will be deactivated when I will install windows 7 on my new hard drive?
    Thanks a lot!
    Regards
    Remy

    I use Win7 32bit on my Satellite A300. It works perfectly and all Toshiba specific functions are there.
    Here is the list how I have installed all stuff on my Satellite A300 (PSAG8E):
    -Win7
    -chipset driver
    -storage manager
    -display driver
    -sound driver
    -modem driver
    -supervisor utility
    -infrared
    -patches
    -configfree
    -VAP
    -toshiba hardware setup
    -HDMI control
    -WLAN driver
    Everything works well but some drivers are missing
    Added Vista stuff:
    -Toshiba assist - work properly
    -Card reader - installed properly
    -Webcam driver for A500 - tested with Skype - work properly.
    -Synaptics driver
    Win7 works much better and faster as original Vista.

  • Satellite A300-276 - nvraid.sys error on Windows start

    Good evening,
    I am recently trying to install Windows 7 in my Satellite A300-276. I actually install it but when I want to start it apears a message saying:
    "Windows failed to start. A recent hardware or software change might be the cause. To fix (...)"
    and then, in the same page:
    "File:\Windows\system32\Drivers\nvraid.sys"
    "Status:0xc0000098"
    "Info: Windows failed to load because a critical system driver is missing, or corrupt"
    Could someone help me with this?
    Thank you very much.
    Best regards,
    Andr

    I have installed Win7 32bit on my Satellite A300-1LI and on P300D successfully and it runs perfectly.
    I don't have time to read the whole thread but what I sugesst you is to install Win7 32bit again and all other stuff following my installations order. It worked for me so I think it should be ok for you too.
    Here we go:
    Satellite A300 (PSAG8E) and clean Win7
    -Win7
    -chipset driver
    -storage manager
    -display driver
    -sound driver
    -modem driver
    -supervisor utility
    -infrared
    -patches
    -configfree
    -VAP
    -toshiba hardware setup
    -HDMI control
    -WLAN driver
    Everything runs well but some Win7 drivers were missing so I have installed follow Vista stuff.
    Added Vista stuff:
    -Toshiba assist - work properly
    -Card reader - installed properly
    -Webcam driver for A500 - tested with Skype - work properly.
    -Synaptics driver

  • Satellite A300-1MV slow boot up and slow running

    I have recently bought an Satellite A300-1MV it runs vista,
    I have the trial Mcafee running and the other pre-installed software that came on the laptop. My problem is that on boot up the computer seems to take a ridiculous amount of time to boot up, once past the vista orb it says please wait which lasts about a minute untill the password request appears.
    I had a look in the problemreports in control panel and found that the toshiba tempro program was hanging on boot up so disabled it but didn't seem to have any effect, I also find that when for example you double click on a photo thumbnail to view it, it takes about 30 seconds to appear on the full screen allthough the window is shown on the start menu bar at the bottom allmost straight away.
    I have defragged the hard drive, scandisk, memory checked, virus checked etc.. I compared it to a friends laptop dell that has less memory but same spec processor and vista and that appears to work 10 times faster.. any ideas?, I do wonder if its a toshiba program causing the problem.
    I do though have a problem with acrobat reader opening of its own accord and telling me it can't read the file ( don't know what file)
    I have uninstalled this and reinstalled but still have the same issue!...HELP!!!
    Cheers

    Hello
    Very nice thread about slow start up you can find under http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=134947
    To be honest I don't like McAfee and I have installed other antivirus application that needs much more resources. Please read this interesting thread and let me know what do you think about it.

  • Satellite A300-MM1 - start-up is very slow

    I bought 3 Laptops (Satellite A300-MM1) a month ago but I noticed they were all very slow at start up (boot).
    They took about 6 minutes till I saw the desktop and sometimes don't work.
    Satellite A300 MM1 (harman/kardon)
    Windows Vista Home Premium (Service Pack1)
    Intel(R) Pentium(R) Dual T3200 @ 2.00 GHz 2.00 GHz
    3.00 GB RAM
    I thought it was the Antivirus but I put McAfee Antivirus in two of them and Kaspersky in the other but I faced the same problem.
    What I should do?

    I bought an A300 21H and start up was appauling so I took the following out and now I'm up and running in about 30 secs,
    Tempro
    Config Free
    Toshiba power saver
    Mcafee AV and now using Kaspersky
    Chicony Tray
    and disabled flash cards via control panel (can still use F keys)
    When I first got my laptop it took 2 min to start up and battery life of between 1 hr 10min to 1 hr 30min
    by removing the above my start up is under 30 secs and battery life is about 2hr 30 mins.
    The programs were removed by using the RUN and typing msconfig
    untick the boxes under the START UP tab that you dont want running
    RESTART machine then CONTROL PANEL and uninstall them
    Please note Mcafee needs a removal tool off their website to completely remove it..
    Flash Cards was disabled only and not completely removed via CONTROL PANEL then PERFORMANCE ICON then top left hand corner MANAGE START UP PROGRAMS then DISABLE..........
    Now your laptop will be very much quicker

  • Satellite A300-1PH - Very slow statrting of Windows

    Toshiba Satellite A300- 1PH.
    Due to some Viruses, I started the recovery on my laptop and installed the fresh windows Vista Home premium. But now I am facing a problem.
    My windows load very slowly. When I start my Laptop, after the logo of Windows appear, it takes almost 4-5 minutes to load the Destop and the Secreen shows the message "Please Wait".
    Before recovery it never took such a long time. It's been onliy 1 month I have bought it.
    Can any body tell me please what is the actualy problem?

    I am very happy you are satisfied now. Many times on this forum I wrote about right OS configuration.
    Anyway, Tempro is nice application and useful for people with low level of notebook knowledge who need some help with updates and notebook monitoring. In my opinion this can just confuse notebook owners with different messages and upgrade notifications.
    I recommend you to remove it from the system. Believe me with les such background running processes and applications your notebook will run better and more stabile.
    For years I use Avira Antivir and it the best solution. It runs in the background, doesnt need many resources and make updates automatically. You can get it for free under http://www.free-av.com/
    Latest version is 9.00.
    If you have more questions please let me know.
    Bye and good luck.

  • What is the part number of MB of Satellite A300-1L0 PSAGCE

    Hi
    I've got Toshiba A300-1L0 Model NO.PSAGCE-03100UGR.
    But there is a problem with graphic adapter ATI 3450 (M82 chipset). After installing proper drivers I got blue screen when Windows starts - and it is written that file ati2....dll gives the problem. The same situation happens both on Windows XP and VISTA.
    What is the part number of mentioned notebook mainboard? I'm planning of selling every part of this notebook that is why I would like to know the part number.

    Hi
    Not sure exactly if the part number is the same but the PT10G_6050A2171501_MB_A03 motherboard is compatible with Satellite A300-1QD, A300-1GC and A300-1L0
    But I dont know why the part number is so important you can describe the motherboard as a mobo for Satellite A300 PSAGCE series.
    There are different Satellite A300-xxx which belongs to the PSAGCE family and this motherboard would be compatible with all these notebooks

  • Why does Photoshop keep slowing down?

    I've been using Adobe Photoshop CS5.1 for two years now, and for some reason it seems to have the problem of slowing down after using it for a while, so if I'm working on a project I have to keep closing it and reopening it to get it fast again. It's weird because it doesn't seem to matter how much stuff is on the canvas, it's just how much I've drawn and hit undo and erased or did anything, After like 5 minutes of straight work it just gets too slow for me to work in, like when I switch tools or change the color it takes a couple seconds to respond. So literally every couple minutes I have to restart Photoshop and open the same file.
    What's really odd is that sometimes Photoshop will work perfectly fine and stay lightning fast for hours. Like, for the last couple of months it's been 100% fine, but since a few days ago it started to have this "slowing down" issue again. Every couple months it seems to decide to be perfectly fine or just really annoying. I didn't change anything in my computer.
    It can't be my computers specs or my settings in Photoshop, but I will tell you all of that anyway.
    OS - Windows 7 64-bit
    CPU - Intel Core 2 Quad Q6600 @ 3.0GHz
    RAM - 12GB DDR3 @ 1333MHz

    There is no malware scanner running, in fact I have tried closing out all other applications and unnecessary processes to help improve performance. No luck.
    Also, my post actually wasn't quite finished, but my internet shut off on me last night and I guess that just automatically posted whatever I had done before then. What's even better is that the forums won't allow me to edit it. What great features!
    Anyway, here's the FULL spec sheet of my computer...
    OS - Windows 7 64-bit
    CPU - Intel Core 2 Quad Q6600 @ 3.0GHz
    RAM - 12GB DDR3 @ 1333MHz
    GPU - NVIDIA GeForce GTS 450 1GB
    Storage - 1x 128GB SSD (OS installed on), 1x 750GB HDD, 1x 160GB HDD
    I have the 64-bit version of Photoshop CS5.1 Extended, installed on the SSD. Here's the settings I have in the preferences:
    Memory Usage - 100%
    Scratch Disks - All 3, SSD 1st, 750GB HDD 2nd, 160GB HDD 3rd
    History States - 100
    Cache Levels - 8
    Cache Tile Size - 1028K
    I have fiddled with these settings and restarted Photoshop countless times. In the end it's the same exact result: Photoshop slows down after a few minutes of work and I have to restart it. I have about 50GB free on the SSD, 150GB free on the 750GB, and about 140GB free on the 160GB.
    I don't understand why it gets so slow even when my RAM usage only makes it up to about 45%. Why doesn't it just utilize ALL of the memory like I told it to?
    I've tried setting cache to 1, 2, and 4, same result. Cache tile size to all the different settings, same result. History states to an extremely low level like 10, same result. I just don't understand why Photoshop is doing this, especially because it decides to speed up on its own every couple of months...

  • What is the difference between Satellite A300-1EC & Satellite A300-1EG

    Why does the Satellite A300-1EC stand dearer as Satellite A300-1EG, but on configuration loses him?
    What is their substantial distinction in?
    What model of notebook can advise, in this price range?

    Hello
    Satellite A300-1EC belongs to PSAG0E group and Satellite A300-1EC to PSAG4E. When this model numbers are different that means they don't have the same hardware configuration.
    The first one has Intel 965GM (Crestline) graphic controller. The second one has ATI M82XT (256MB). The HDD capacity is not the same. The first one has 160 GB HDD and second one 250 GB.
    So that is the difference between these A300 notebooks.
    In my opinion the second one is better. You must make your decision and choose the right one.

Maybe you are looking for

  • I have no idea how to transfer songs on my Yamaha PSR-E323 keyboard to my macbook. How do I go about that?

    I purchased a Yamaha PSR-E323 61-key digital keyboard. I recorded some parts of songs out of the blue that I really like. I don't know what I was playing. It was just something that sounded good at the moment and im going to have to leave my keyboard

  • Error while exporting PAR file

    Hi, I am getting an error "Build of project failed" while exporting a PAR file to the project folder and it is showing that "The project was not built due to classpath errors (incomplete or involved in cycle)." I am very new to this technology, so pl

  • How to give constant data in RFC function module

    Hello;     I have created a BAPI which doesnt have any data i want to put some data in that BAPI so tried with constants but it is not working..how put hard code data in function module..when i put the data it gives error stating that 'Function-Pool'

  • WRFMASSMAT does not work properly

    Hello, this is my first post in this forum. I have a problem regarding the Transaction WRFMASMAT. This transaction should be available to users without the permission to access the transcation MM42. I have added all neccessary objects from the MM42 t

  • Husband and Wife names in Contacts

    Please help. I'm trying to enter into Contacts the following: "John & Jane Doe". I am entering "John & Jane" as the First Name, and "Doe" as the Last Name. All seems fine, but at some point the system retains "John" as the First Name and changes the