Why K8N Neo2 PT cannot see my Mitsumi 7in1 Internal Media and Floppy Drive????

I have this board from a month or so, the first time I installed it I noticed it failed to detect and install (in windows) my 7in1 internal MultimediaCard reader included in my mitsumi floppy drive. The reader is USB and it's attached to one of the available onboard USB extra pin headers. It works regularly, infact if I attach it to another mainborad like ASUS A8V, it is detected and self installed in windows everytime. K8N Neo2 simply ignores it as the reader has never been attached to it. Sometimes it happens that I turn on my pc and the reader is detected and installed in windows but when I restart or I turn off my pc, the reader disappears again for an unlimited time....I have tried everything, from flashing any existing bios, to change USB pin header, disable every unused controller or port from bios (Serial port, parallel port, firewire etc) but nothing fixed the problem.
is there someone else who has the same problem with an internal USB card reader on MSI K8N Neo2 Platinum MB?
any suggestion?
thanx

Thanx for your help WONKANOBY! but I have different pins connected on my USB internal reader as shown in the modified picture here:
PIN2 X X X O X (pin 2-4-6 and 10 not connected)
PIN1 O O O O X (pin 9 not connected)
as you can see I have pins from 1 to 7 connected and on the other row only pin 8 connected...tell me what to do, should I cut pin 8?
Thanx

Similar Messages

My iPhone (5s/8.1.2) and iPad (orig mini/8.1.2) cannot see my Mac Book Pro (Yosemite) and vice versa in Airdrop

My iPhone 5s (current iOS 8.1.2) and iPad mini (ditto) can see each other in airdrop, but neither one can see my Mac Book Pro (early 2011/Yosemite). And the Mac Book Pro cannot see either iOS device.
I have read everything I can find about this and it seems like these iOS devices SHOULD be able to exchange with my Mac Book Pro using Airdrop, but I am unable to make it happen.
Can anyone enlighten me on what might be going on here?

I have been just wandering for quite a night over the web to find out a solution to this particular issue (no mid-2012 mac visible in Airdrop on iOS).
So, I seem to have found it and must share it:
the airdrop started working bidirectional for me after I had changed the following settings to "off" (or whatever it may be called in English version): system settings - network - bluetooth PAN - IPv4 configuration -> off.
If it works for you, please share further, because the problem seems very common with no solution readily offered.

3 questions: 1) I am unable on my Mac Book Pro to enable iCloud Photo sharing in iPhoto preferences, why not? I cannot see my iCloud drive contents.Why not?

Having a Macbook Pro i have taken and loaded in 569 photos from my cameras and want to share using iCloud. But I simply cannot get iPhoto to enable iCloud photo sharing. What could be the cause? what should I try other than the instructions which I followed three times already as outlined in the FAQ section of the help function?

OT
Thanks for the suggestion . As soon as they hand me my laptop at the store in 45 minutes time I shall try the disable and then re boot as you suggest.
so far they sent me this; Disk has no problem.They may have more to say to me re the flash drive and results of storage diagnostics and ASDs ( what is this? ) when I see them .
The case repair is redundant to the problem I am having but if they give me a new one worth $399 i will not complain,eh.
Problem Description/Diagnosis
Issue: MacBook Pro is running extremely slow. Specifically IPhoto
Steps to Reproduce: Attempted to repair disk, no issues found.
Cosmetic Condition: Scratches to enclosure and clamshell.
Proposed Resolution: Tighten MagSafe board. Run storage diagnostics and ASDs if no trouble found with flash drive.
Estimated Turn Around Time: We'll call you in 3 - 5 days
Mac OS Version: 10.10.x
Hard Drive Size: 251 GB
Memory Size: 8 GB
iLife Version: Unknown
Employee 1178255246
Repair Estimate
Item Number
Description
Price
Amount Due
Customer KBB
661-8154
Housing, Top Case with Battery
$ 399.00
$ 0.00
S1490LL/A
Hardware Repair Labor
$ 39.00
$ 0.00
Tax
$ 0.00
Total
$ 438.00
$ 0.00

Why partner function description cannot see in the billing item?

Hi Experts,
I have one doubt about partner function.
I have created a new partner function with description and assign this partner function to the billing partner function procedure.
When I create the billing document, in the item level, I can only see the partner function name, but description is missing.
What is the reason?
Does any one meet such kind of situation before?
Hope to give me some suggestion.
Thanks in advance.
Best regards,
Chris Gu

Hi Chris Gu;
In the SD module personal numbers addresses are determined to be
the address of the personal area.
If the personal number is assigned to a sales office or sales
organisation the system shows the address of the sales office and
if there is no sales office the address of the sales organisation.
If you have no sales office or sales organisation assigned and is
not assigned to a personal area, the system does not determine an
address.
Please maintain the assignment and the address should be displayed.
If you want the private address of the personal number to be displayed
you can use modification note 63258. Please consider that
this may conflict with data security.
Regards
Ruy Castro

Cannot see a particular file on an External Hard Drive- file is not hidden!

Hi folks,
I think this should be a common problem, but I couldn't seem to find an exact match to my topic in the search, so I hope you guys don't mind helping me out if this has been asked before!
Well my problem is basically stated in my subject. A few days ago, I plugged in my friends external hard drive to copy some files off of. Everything loaded fine once I plugged it in, but the problem was that the file that I needed to copy was invisible in my finder! Other files were there, and the remaining disk space indicated that it was there, but the file itself was not!
I disconnected and reconnected the HD several times but to the same problem. I tried to search for it in the HD directory, but it didn't bring up any results.
My friend confirmed that the file was not hidden, and so we plugged it into her sisters Mac Book to test it and it was there! I ended up having to copy it from the Mac Book then transferring it back to my iMac, but I'm rather concerned about this problem because I wouldn't want it happening again!
One slight problem now is that I don't have my friends HD to test any solutions at the moment, so I guess my main question is to know why does this happen/what causes this to occur? I'm think it's my iMac acting up, because it has been running a bit slower and noisier lately, so I'm thinking of reformatting my iMac? What do you guys think?
Cheers!

Hmmm, only thing that comes to mind at the moment is Permissions, Admin Rights, Groups, or HW/SW!

Macbook pro/snow leopard cannot see photos on iphone 4 ios7 and therefore cannot download

Since installing a new hard drive, my macbook pro 2009 / snow leopard shows no photos on my iphone (when there are 147). I have not had a problem with downloading photos previously. Any help appreciated.
Tim

Have you synced the phone with iTunes on the Mac? Have you installed all system updates? iOS7 only works with later versions of iTunes & the OS.
iPhoto should allow you to see the pictures & import them from the phone. The other option is 'Image Capture' application. It should be in the Applications folder.
You may also need to unlock the passcode to show the device on the Mac.

After I enter my password in my Mac mini, my screen turns black. I know it is there, ( i can hear the assistant), but I cannot see anything. i went to Genius and they said hold Control, Option, P, R on the re-boot to get back to factory settings...

I went to the Genius bar and they told me to Control, Option, P, R on a reboot to restore the settings, but with a wireless KeyBoard it does not work. I installed my standard PC keyboard, but am not sure what keys renase the display back to factory settings.

Hello Dominique,
Generally on a PC Keyboard...
Windows key = Command key on Mac
alt key = Option key on Mac
PRAM reset, CMD+Option+p+r...
http://docs.info.apple.com/article.html?artnum=2238
With PC KB... Windows+alt+p+r
But try holding the Shift key down at boot to get into Safe Mode, see if the Display settings need adjusting.

I have FireFox 5 installated, but I cannot see the x in right corner and cannot close my programs more

It is beginning after installeted nr 5, before I had nr 4 and I will this back
It works much better, I don't like changing programs, what good is and workst must stay

Go to View (or just right-click on any empty space of Firefox's panels - for example, near the tabs) and turn off the Main Menu Panel. You'll see what you're looking for.

With version 5 of Firefox, if I open more than 1 session, most of the time I cannot see anything in the navigation bar and my back and forward buttons do not work.

I open 1 session of Firefox 5.0.1 and everything seems to work fine. Then I open a second session of Firefox and most of the time the navigation bar does not show the page that I am on and the back and forward buttons do not work. When this happens, the first session always remains working. I am an internet marketer so I have at least 2 or 3 sessions going at any given time.

A possible cause is a problem with the file places.sqlite that stores the bookmarks and the history.
*http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode
*https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

Cannot see video, I get green screen and can only hear the contents

I've unintalled flash player and adobe shockwave and re-installed it again but I am getting the same problem. Video is not working. I dont know what to do.

Hi ,
Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about yourwith the Video not working correctly or green. Try clicking on the green screen, in the tab named Local Storage and put 10 KB and the green screen should disappear. Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system that need updating as the graphic driver could need updating. Have you tried another browser? This link will help you update your browser if needed. Let me know how this goes. Thanks.

HT1660 I cannot see my library which is on an externa drive. .

Can anybody help, I have used an external hard drive for all my music (all formats). It is normally plugged through my laptop. Have recently bought speakers for the desktop and have now downloaded itunes to it with the intention of using it.
I have plugged the external drive in and changed the library folder in preferences/advanced to point at the hard drive. This did not work.
Tried holding down the shift key on start up and changing it that way, it still didnt work. There seems to be no itl file in the folder on the external hard drive.
So tried creating a library by pressing shift on start up. When opening itunes now it just has a generic screen asking me if i want to start downloading or ripping CDs.
I am sure it is something very simple that I am just not getting?
Oh and also set up sharing as well, still no joy.

Connect the external drive back to the laptop then read make a split library portable.
Feel free to ask questions...
tt2

I have removed my external hard drive from my laptop and moved it to a workstation, both pc. I have authorized the workstation with my apple id, but somehow I cannot see my music that is on the external drive in my itunes. Any suggestions?

ANYONE?

You can usually enter anything you want for the user name, but the password will need to be the device password for the AirPort Extreme....(not the wireless network password).

Why did 6.1 update have to delete all my media and contacts?

I updated my Iphone to 6.1 and it locked up with an itune icon on the face. Now I have to recove it and lose all my data.

Yes you have to delete media to make the 2.7 GB available. When updating is done, the newer IOS only takes a max of 100 MB more storage than the old iOS. The iPod needs the extra space to do the installation.
You can update via iTunes. Just note that if you do all synced medial like a and music have to in the iTunes library.

Why i cannot see 'Objects and attachments ' in decision step?

Dears:
i am doing some workflow in SO, but i cannot see the object link under 'Objects and attachments ' in INBOX. like 'Sales Order: 0500001005 '.
i have do the binding from workflow to task.
any advice?

Hi
This sounds like a binding issue.
Make sure that:
1. You have created the binding from the workflow container to the task container
2. The object (Salesorder) is correctly instantiated when you're using it in your task
3. Make sure that your not binding out any invalid object/ values to your salesorder workflow container object in any of the previous steps.
Regards
Morten Nielsen

System suddenly won't power on (MSI K8N NEO2 PLATINUM NFORCE3)

System specs are
COOLERMASTER TAC-T01 WAVE MASTER ALUMINUM ATX 4X5.25 1X3.5 4X3.5INT case
MSI K8N NEO2 PLATINUM NFORCE3 ULTRA S939 AGP 5PCI SATA 1394 SOUND 1000LAN
KINGSTON HYPERX 1024MB DUAL CHANNEL KIT PC3500 2X512MB DDR 433MHZ 184PIN
ATI Radeon X800XT PE AGP
SEAGATE BARRACUDA 7200.7 200GB SATA 8MB 7200RPM 8.5MS OEM
CREATIVE SOUND BLASTER AUDIGY 2 ZS 7.1 1394 PCI RETAIL BOX
LITEON 16X DVD-ROM INT E-IDE RETAIl
MITSUMI FA404A 7-IN-1 FLOPPY DRIVE & FLASH READER CF/SM/SD/MMC/MS
LG 4163b dvd burner
Nothing has ever been overclocked on this system.
Everything is plugged into a Belkin Surgemaster powerbar.
I haven't mentioned the power supply. I'll get to that. I have been using an ANTEC NEOPOWER 480W POWER SUPPLY (ATX12V DUAL 12V RAILS ACTIVE PFC W/ DETACHABLE OUTPUT CABLES) for about a year on this system without
any issues. One morning, I wake up, hit the power button on my coolermaster case, and nothing happens.
CPU fan won't even spin. Nothing happens.
O.k., blown power supply, I think . . . .
So I take out my Antec and put it in another system. That system turns on
without any problems.
Hmm . . .
I come here, and I read posts about
potential compatibility issues with Antec power supplies. But if it's a compatibility
issue why was my system working for about a year?
O.k., fine. I'll buy a Enermax 535W EG565P-VE FMA 24P (115/230 VAC) power supply.
I just plug it into the mainboard (nothing else). Hit the power button . . .
The CPU fan spins for half a second, and then nothing.
Did my motherboard just suddenly die for no reason?
Any suggestions?

Pull the AC plug from PSU and set cmos in clear position with battery removed for atlest 20 minutes perhaps longer .
Then try to post the system barebone .
Just cpu,1 pcs memory in slot 1 , gfx card , and keyboard in PS2.
No usb devices at all including card reader and no pci cards harddisks or cdoms/dvd/floppy.
It could also be caused by a short or a malfunctioning fan connected to mobo.
Try to disconnect all case fans from mobo headers if you have any connected to additional fan holders.
The chipset fan can also be disconnected momentarily just to see if it posts.
If none of this helps , replace cmos battery and try again .

Why K8N Neo2 PT cannot see my Mitsumi 7in1 Internal Media and Floppy Drive????

Similar Messages

Maybe you are looking for