Why MSI DKA 790GX platinum BIOS 1.7 dun have EEP mode for DRAM setting

hihi,
may i know why MSI DKA 790GX platinum BIOS 1.7 dun have EEP mode for DRAM setting?
cos i cant see EEP using CPUZ.

Quote from: Fredrik on 22-May-09, 09:15:00
I have no good answer, just a rule of thumb: After a BIOS updae, pull power cable out and clear CMOS.
In this thread it says Kingston may not have EPP settings, but if it worked previously... Perhaps the memory controller didn't understand you had that memory to begin with?
Better ask: Is everything the same, before and after update? Why did you update?
Quote:
1.7 Update Date 2009-03-31
Description - Update CPU module.
- Update memory module.
- Fixed SmartFan function cannot work properly after resume from S3.
i update to v1.7 because when i first plug in the 1066Mhz RAM, it only show 800Mhz in bios, so i update to v1.7 as the update include "update memory module".
anyway my system is fine, as i have run 8 hr of memtest.
just want to know why there's no EPP option in v1.7
p/s. I think i saw EPP option in v1.6 using the same RAM.

Similar Messages

MSI DKA 790GX Platinum problem

Hi !, its my first time i post a new message !, im a french guys and english its my second language... so i will try to do my best...
I bought last week a MSI DKA 790GX Platinum with Amd Phenom 2 940...
I set up all my new pc with OCZ Fatality 4 x 1g ddr2 1066 and WD 640g SATA and a Ultra 600w
First think i saw when i get out the MoBo of the plastic bag, 3 pins of the Flat circu-pipe are broken, i found the 3 spring in the bag... (i can take picture...) but the flat circu pipe stay in place with 1 pin and maybe thermal compound (no sure)... anyway the pc start #1
at the start of the pc i got the unknown processor msg like everyone cause i have the 1.2 bios version
im using the onboard VGA for bios setting,format and install Vista business 64bit.
Come on the forum and use the USB Flash technic... i do everythink you say... work perfectly, bios update to 1.6...
After a reboot like its say a the end of the bios update... I got cmos error... and cant boot anymore
i tryed to clear my cmos error with the button on the MoBo... nothing, or sometime... when i restart my pc... my screen show horizontal bar changing color to red to blue to yellow....
after 30-45min wasting time for reboot,/clear cmos/ remove battery... nothing...
I put my 8800 gt in the pci-e and magiccc.... pc start #1... work perfectly...
so dont no what happend to my onboard vga with the 1.6 bios update
Next week i will get my sapphire 4870 1g ddr5... so dont no now if i will get problem :(
Dont no if anyone here got this problem and solved,
thank you

Bas, Thats not the answer
His onboard vga is disabled, on the 1.6 bios update MSI have decided to disable the onboard vga by default, meaning someone either has to go and get a pci-e gfx if they haven't got one or if they lucky enough to still have an old pci gfx they can use that, they need to release a fixed 1.7 bios (as there are other areas messed up).
johnmmclaine514,
if you've only just got the board and it was damaged, then i suggest you get it replaced, as you don't know what else could be wrong with it. And it's better to do it now as you can just do a straight swap, as later on you could be waiting for 28+ days to get it replaced.
the HD 4870 1GB should work fine, I'm running a HD 4870x2 2GB without any problems

Anyone using asus silent knight II on msi DKA 790GX platinum?

hihi..
anyone using asus silent knight II on msi DKA 790GX platinum?
anyway to orient the air flow to horizontal setting. cos right now my cpu cooler was shooting up warm air to my power supply.
thanks

Quote from: nel_hawk on 22-May-09, 08:23:49
Oh I see.. now then know that it's ATX standard. thanks.
then how about the rear fan, is it functioning the same as PSU fan?
or is the rear fan's function is to suck out the whole system's warm air?
It's to help getting hot air out, but that is added by case builders.
Here you have the original specs: http://www.formfactors.org/developer%5Cspecs%5Catx2_2.pdf
Case builders added extra fans because ATX standards aren't good enough for high-end systems.
However, ATX is designed to let the PSU suck out the hotair...
Anything you add to it makes it all cooler and doesn't hurt.
You should know that AMD CPU's do not get very hot at all, it's the Intels that do, especial the Pentium4, so case builders created all sorts of solutions to cool them down as ATX wasn't sufficient for the P4.
Even Intel made a new spec BTX, but that wasn't accepted by builders.

Team Xtreem ram setting on MSI DKA 790GX Platinum

MSI DKA 790GX Platinum running AMD Quad 9950 Phenom Black Edition with Xigmatek Red Scorpion CPU cooler
MSI R4870X2
Team Xtreem 4GB 1066
Seagate 500GB
Samsung DVD SuperWriter
Coolermaster CM690
Aerocool 750W Modular
Win XP Pro SP3
How do i set the ram settings to get the rams to run at 1066Mhz?
anyone can teach me? Thanks in Advance!

Quote from: jason1980 on 20-January-09, 09:03:04
the Dram timing mode, there is DCT 0, DCT 1 and both.
Which one should i use?
I need to change the voltage cos cpuz shows my ram running at 1.8V below the 2.1V needed to run at 1066Mhz.
Thanks, i will try.
CPU-Z is reading the SPD tables - it is not reading the actual VDIMM voltage.

Flash Bios on MSI DKA 790Gx Platinum

Hello everyone, how are you? I hope well, this time I come with a question, I would like if someone could kindly help me flash my motherboard, since I want to update the bios to the latest version, but I encounter various difficulties ... For starters, when I want to make the turn into bootable pendrive, floppy only supports me, and I do not use floppy ... then not let me enter data in pendrive him.
Finally, try to flash the bios from Windows, reboot the system, and after a little while charging the system, the installation started, but I throw an error, something like "CMOS checksum bad" or something, and I could not do anything
I hope you can help me, of course I thank you all!

Well, thank you very much for to see answered my constulta, the problem is this. The bios, when you upgrade to a newer version, it gives me the option of M-Flash, which is a utility to easily achieve the bios update, and finally learned how to use it, but the problem is this, when the BIOS is updated, all drivers load, and then pulls a mistake, CMOS Checksum bad, do not understand that error gives, and lets me choose between two option, F1 to run setup or F2 to load default data and continue, most of F1 tighten the time, but that did not know which was the most convenient option! For example, achieves update the bios, always taking the F1 option, and with the highest error, and when I enter the system, I blocked everything is labeled, and sometimes there is no choice to be reset, a probe with previous versions bios, and also was the same, try everything and not be able to walk properly the computer, until you install the bios by default, the 1.2 ... But I ran into problems such as the video card can not install the AMD Display Driver, and has no solution, then that is what is really happening? I would have to try to update the bios and press F2 so "continuous"? Because I want to update the bios, so that in the not too lejando, I bought a phenom processor 6 cores, and for that, I need to update the bios, so it says on the official website, you need a bios update to use 6 cores processors ... Please I need help!
I expect response and already, I thank you very much!!

MSI DKA 790GX Platinum

Well, this might be a dumb question...but I will ask anyways.
On my motherboard. near the PCI slots, it says 7550 v1.2, doesn that mean it has BIOS version 7550v12 ?
I am planning to buy Phenom II 810/910, so ned to know if I shld update BIOS to v14 or v15.
Thanks.

you will be able flash the bios with the phenom II connected, if you have a spare pc why not download the bios updates. I would get both 1.5 & 1.6 as originally I had isuses trying to update to 1.6 from the original bios, but was able to update to 1.5 then 1.6 without problems.
If you haven't already got a bootable usb stick, then make one, and copy the bios files and tools across - next ensure it is in the new system before switching on, and then press F11 for boot menu, and select to boot from USB, you'll then be able to flash bios from command line

MOVED: MSI DKA 790GX Platinum CPU voltage

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=130553.0

Here is AMD's specification page for the 125 watt 9950:
http://products.amd.com/en-us/DesktopCPUDetail.aspx?id=447&f1=&f2=&f3=&f4=&f5=&f6=&f7=&f8=&f9=&f10=&f11=&f12=
The 140 watt is the same except a temp up to 64C is acceptable while the 125 watt version maxes out at 61C. You can feed it more voltage, without it frying immediately, but AMD still says the range is 1.05v to 1.30v and you are shortening its life expectancy running higher volts.

MSI DKA 790GX Platinum + HDMI + Philips 105S (105S2) Led Tv 32 5000. Problems.

hello all, well the following problem has to do with the connection between my motherboard, and my tv with HDMI LED, the problem is that I plug the HDMI directly to the motherboard, ie HDMI to HDMI, and I recognizes no nothing , absolutely nothing recognizes it , and do not understand that, should work perfectly because I am connecting the HDMI directly
I am in a subject with respect to the VGA in this forum from MSI, but I wanted to know if you could help me solve this problem also, which is the HDMI to HDMI connection direct to the motherboard ...
the connection is good, the cable is in perfect condition, the updates are good, not what would be the problem ...
I would love for support from you, and I have very good references
from and I thank everyone involved in the solution of this problem
MarkitoX

ohhh of course, thank you very much for the answer, but there is error, I have disabled the video card on the motherboard, then it is impossible for me to grasp if you are off the ...
sorry if I did not remember before my mistake ..
thank you very much for everything, I will continue in another post that hize on the conflicts I have with the monitor, and my video card MSI ATI Radeon HD 4850 ...
thanks: D
MarkitoX

MSI DKA 790GX Platinum CPU voltage

I am trying to squeeze more out of my phenom 99950BE.
It is now stable @3.2Ghz for 10hr+ on prime 95 with 1.43V
Problem is i cant get any higher. And the max voltage from the board is only 1.45V?
even 3.3Ghz @ 1.45V results in BSOD and restarts.
Any ideas how can i push my processor further?

Here is AMD's specification page for the 125 watt 9950:
http://products.amd.com/en-us/DesktopCPUDetail.aspx?id=447&f1=&f2=&f3=&f4=&f5=&f6=&f7=&f8=&f9=&f10=&f11=&f12=
The 140 watt is the same except a temp up to 64C is acceptable while the 125 watt version maxes out at 61C. You can feed it more voltage, without it frying immediately, but AMD still says the range is 1.05v to 1.30v and you are shortening its life expectancy running higher volts.

Video problems DKA 790GX Platinum

I've had some problems with my mobo as below:
1. I have to turn on many times the PC for get video from my ATI 4890 (sapphire vapor-x 1GB)
2. If I don't have video, I plug the vga connector to the vga output of mobo and I can see the video signal
3. Maybe when I install new hardware (hdd, memory sticks or anything else) the bios looks like reset, and occurs the 2 points before mentioned.
My hardware: DKA 790GX Platinum, 4 x 1GB Corsair Dominator 1066 2.1V, AMD Phenom II 955 (@3.2 Ghz), ATI Radeon HD sapphire 4890 1GB vapor-x, 2 x 1Tb Hitachi 7K1000.B.
Thanks in advance.

Try just one memory stick in 1st DIMM close to CPU socket, then see if problem will persist.
Also list PSU brand with details[look for them over PSU sticker]

Dka 790gx platinum vga problems

im running a new build with the dka790 gx platinum mobo and an amd x4 9950be. i have updated the bios to v 1.6 ,o.s. is vista ultimate. problem is using the onboard vga , after the post screen and the progress bar for windows ,the screen goes black and no picture, even worse is using my xfx geforce 2 8500 card, the screen is distorted on boot up , but if i leave it running for 3 minutes, switch it off and reboot its perfect? any ideas guys?
dka 790gx platinum ambios v1.6
amd phenom 9950 be
2x2 crucial pc2-6400 800mhz ddr2
hitachi deskstar 7k1000 1tb sata 11 32mb cache
600w psu
xfx geforce 8500gt itb ddr2 pcie 800mhz

Shows us full details about hardware used, read >>Posting Guide<<

When will the MSI K8N Neo2 Platinum BIOS 1.C be released?

Hello
When will the MSI K8N Neo2 Platinum BIOS 1.C be released?
Thanks
FearTec

Don´t know the reason for you guys, for updating bios, but basically I would recommend Syars modded EasyBios, based on the 1C3 (1C0) version.
Check out the link in Syars sig or read it here;
https://forum-en.msi.com/index.php?topic=59711.0
and read about the differant version and you´ll get a pretty good idea whats changed and added.

MSI K8N Neo Platinum ,bios issue or HW

Hi i am using a system like in the signature described (usind adata instead of twinmos) im cooling with a prometeia system , and the board ist watercooled.
My CPU is a Newcastle (@2800mhz ) my graphic card is the normal 9700pro (it makes no diff in oc if the card is clocked or not)
Now i got some serious problems , i can´t run high fsb sync ? Why ? i wasn´t able to do this with the twinmos ram , but i read twinmos has some serious problems with the nforce3, so i purchased 2*512 mb adata.
I tried different dimm combinations (1/2 ; 1/3) that didn´t made any difference
I tried different bios (1.2 1.25 1.31 1.1) but this didnt made any difference either (using 131 now)
my pci/agp is fix (always 66,67/33,34 in clockgen so its just perfect)
i don´t use any SATA devices (all disabled in bios)
What is my Problem ? is it only a bios problem , or is there hardware in my sys which makes probs? Could it be an IRQ Problem (got 2 pci cards in slot 3 and4 its an IDE raid controller and a soundcard)
i hope there is any help for me :(

Well this is the second time someone mentions problem with Adata DIMMs:
https://forum-en.msi.com/index.php?threadid=55475&sid=
Maybe it's about time to post it here:
https://forum-en.msi.com/index.php?threadid=51997&sid=
For all I can think of right now, either run the board with a single module or both with 5:6 divider

CPU MIS MATCH ON DKA 790GX PLATINUM

Hi, I just installed a new AMD Phenom II (125WATT X6 1055T) on the motherboard in question. I updated the bios to the latest version of course available on the MSI website (file name: 7550v1D.zip) but unfortunately two very strange things happen. Once the system detects that you are part of the CMOS errors regarding the date within the bios system bios with the correct date, and restart the following error: "CPU MISMATCH DETECTED, FATAL ERROR, System halted". Someone help me know?
Thanks for any replies!

Do >>Clear CMOS Guide<< with power cord removed
Also read >>Posting Guide<<

DKA 790GX Platinum - HT Limit

In the Bios, Higher HT Settings are available via Multiplier, I think it has MAX Setting up to 2600Mhz. Phenoms & K10 CPU are only 1800Mhz. What is the limit? Does the board Actually support that High an HT?
In essence The only thing that will hold me back is the CPU & Memory then. AM I correct? I'd like to know, it'll make me feel safer Overclocking the Board, I guess.....

According to MSI's spec sheet, that appears to be correct. But... Since there aren't any processors (that I know of ) on the market that can utilize that HT speed yet, we'll just have to take MSI's word for it.
I'd be leary of trying to OC your HT bus, the downside is huge and the gains are negligible. The current HT data bus capacity is much greater than the data output any of the devices you have.
Here's the current HyperTransport 3.0 specs:
* 1,800 MHz = 3,600 MT/s = 7,200 MB/s
* 2,000 MHz = 4,000 MT/s = 8,000 MB/s
* 2,400 MHz = 4,800 MT/s = 9,600 MB/s
* 2,600 MHz = 5,200 MT/s = 10,400 MB/s
Note that your Kuma processor uses a Stock HT speed of 1800 MHZ. 7200 MB/s = 7.2 GB/s.
A Sata II VelociRaptor harddrive only has a capacity of delivering 3GB/s in theory.
FireWire 1600 and FireWire 3200 will have transfer rates of 1.6 and 3.2 GB/s and should out this year sometime.
USB 3.0 will be coming online in 2009 or 2010 and will have a transfer rate of 4.8GB/s.
All of these specs are the highest possible speeds, under the best laboratory conditions.
In real life, you'll never get those kinds of transfer rates.
Even if you did OC your HT bus substantially, you wouldn't see any benefits because you already have more bandwidth than your devices can utilize.
How do you like your mobo so far? I just ordered one last night, hope to see it Saturday or Monday.
I'm still trying to decide on ram & CPU.
sorry to drift off topic.

Why MSI DKA 790GX platinum BIOS 1.7 dun have EEP mode for DRAM setting

Similar Messages

Maybe you are looking for