Why my airport express dont find my network

My airport express be conected to my airport extreme succesfully, but, a day, after reset my network, the airport express dont find a new network.
I conected by ethernet, but dont work.
I reset airport express many times and dont find.
I dont know why dont worklokes new.

The main problem is that airport utility can't find my express

Similar Messages

New Airport express not finding wireless network

I just got a new AX plugged it in it was recognized did the set up and said to update. It went through the update but the amber light kept flashing. After the update I also lost my internet connection. I have to re-establish my internet connection each time it goes through the update. I have tried the hard boot to the factory specks three times and it still will not recognize my network. I just want to use it to play itunes through my stereo. I am not a computer person so this is very frustrating to me

You will want to configure your AX to "join" the wireless network created by your 2Wire router.
Either connect to the AX's wireless network or temporarily connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing 2Wire's wireless network>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)

Airport Express can only extend network, not create new one. Why?

I am sharing a flat with some friends. The shared broadband router is placed in the living room. To strengthen the signal and make it easier for me to manage, I bought an Airport Express, connected it to the shared router with an ethernet cable and set up a wireless network of my own in my room. It was working fine, until recently we renewed our broadband contract. The router had been replaced by a new one (I don't know why) and the network configration had been changed. Since then I was not able to use my own network. In the Airport Utility display, the light of Airport Express is green, but the light of Internet is yellow, and the status is disconnected. I tried to change various other configuration on the Airport Express, and all in vain. Until I switched the network mode from 'Create a new wireless network' to 'Extend a wireless network', the Internet connection was finally back online. But this merely extends the existing network and not what I want. Why this happens? Why my Airport Express can only extend a network, not create one?

Here is the situation on my Airport Express.
If I choose to extend the existing wireless network, the Airport Utility shows like this:
If I set up a wireless network of my own, what I get in the Airport Utility is this:
See my problems here? The Airport Express does not show anything in amble, but the Internet complains that there is no connection.
This problem did not occur before the broadband was renewed and the rounter was replaced.

Airport Express no longer joins network

Greetings, I have a cable modem internet connection; I use an older Airport Extreme (802.11n, without Time Capsule) to make a local wifi network with WPA2 Personal security, and an older Airport Express (802.11 b/g, firmware 6.3) to connect a laser printer in a different room.
All was working well until two days ago when access to the internet disappeared. I reset the modem, confirmed that the cable connection was working by plugging a laptop directly into the modem by ethernet, determining that the problem was the Airport Extreme. I discovered the 7.5.2 firmware update which I uploaded, and all seemed well.
However, the 27" iMac upstairs only connected to Airport intermittently; it appeared to have been duplicated in name, as well as only recognized the Airport Express. I've since been able to correct that problem, however, now the Airport Express no longer connects to the Airport Extreme network.
I've tried soft resets (unplugging then plugging back in) and hard resets (pressing the reset button with a paperclip until the amber light flashes, then reconfiguring the device). I've tried setting the Airport Express both just to join the network (printer sharing) as well as extend the network; I also reverted the Airport Extreme's firmware to 7.4.2 which works perfectly well. However, now after each successive attempt to reconfigure the Airport Express to join the network, Airport Utility says that the Airport Express has been successfully updated and will restart, which it never does - it simply flashes an amber light, and Airport Utility eventually times out and says that it was unable to find the Airport Express after restarting, noting that the settings have been successfully updated, but that there is a problem re-joining the wireless network/finding the device. Notably, the Airport Express no longer appears in the left hand list of wireless devices in Airport Utility.
Help!!

Hi pslebow,
You make it sound like there was no change, then suddenly the Airport Express 802.11g lost connection to the wireless network and you can't get it back.
What network security is your wireless network using?
From the specification sheet, "…When joining an existing wireless network, AirPort Express only supports WPA-Personal."
AirPort Express - Technical Specifications
Please make sure your router security is set to match.
iOS and OS X: Recommended settings for Wi-Fi routers and access points - Apple Support
If you have older Wi-Fi devices on your network that don't support WPA2 Personal (AES), a good second choice is WPA/WPA2 Mode (often referred to as WPA Mixed Mode). This mode will allow newer devices to use the stronger WPA2 AES encryption, while still allowing older devices to connect with older WPA TKIP-level encryption. If your Wi-Fi router doesn't support WPA/WPA2 Mode, WPA Personal (TKIP) mode is the next best choice.
Best,
Nubz

Hello I have 2 seperate airport express systems on my network, each connecting to a stereo in a different room. suddenly, the one in the living room will not stop flashing amber, but the one in the bedroom works fine. I have already tried resetting it

Hello
I have 2 seperate airport express systems on my network, each connecting to a stereo in a different room. suddenly, the one in the living room will not stop flashing amber, but the one in the bedroom works fine. I have already tried resetting it with a pin, resetting it while plugging it in, and trying to find it in airport express setup (the setup assistant can't find it at all).
What am i doing wrong?

How do I configure the AX to connect to the hub's wireless network? It will only scan one base station Airport Express at a time in the Airport Utility. I think what I am trying to do is use the hub as a router to the two AX's. Is there a specific way to set this up?
To set up the AX to join a wireless network as a "Wireless Client," using the AirPort Utility, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
Launch the AirPort Utility.
Select the AX.
If not already connected to the AX's wireless network, go ahead and switch to it when prompted.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <type in the network name/SSID of the wireless network that you want to join or select it from the pop-up menu>
Wireless Security: None OR, if you are using security on your wireless network:
Wireless Security: <Select the appropriate level of security for the existing wireless network: WPA/WPA2 Personal | WPA2 Personal>
Password: <enter your wireless network security password>
Verify Password: <re-enter the same security password>
Click Update to write the new settings to the AX.

Why my airport express has a yellow light

why my airport express has a yellow light (not blinking)

Before doing a reset try the Airport Utility via Finder > Applications > Utilities ... this might give you a reason for the flashing light. It could be something simple like the software needs updating.
https://discussions.apple.com/message/16700100#16700100

Airport Express extending Base Station network very slow.

Hi,
I have an Airport Extreme Base Station and an Express, both of which are 802.11N. Currently I have my express connected and extending the network hosted by the Base Station but when I am in a location where I use the Airport Express rather than the Base Station it is extremely slow. If I am on a call on Skype for example the calls drop constantly or I have latencies over 2000 if I am playing a game. But Once I am in range of the Base Station my wi-fi is great. Anybody have any ideas as to why?

What are the steps to extend the network using the Airport Exprss with a Linksys router? I have the Airport Express working with my network (a Linksys WRT54G) but have never attempted to use it to extend the network; instead, it just works for Airtunes currently.
In addition, I can't seem to get Airport Express Assistant to work on my Macbook Pro. It says there's an error when it tries to connect to my Airport card, which is odd, since it works fine.
Any ideas?
Macbook Pro Mac OS X (10.4.7)

How to connect a 2nd airport express in a home network?

I'm triying to connect a second airport express in my home network but when I plug in and go to Airpot Utility says :
"This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information."
I don't know what to do to get connect the second airport exprees?, Do I miss something ?

You need AirPort Utility 5.6 to configure that model Express. The problem with that version is that Mountain Lion will refuse to let you install it.
This dilemma is easily solved. You simply need to extract the app from the installer package using a package extractor like Pacifist or unpkg. Pacifist is shareware, unpkg is free.
Download Pacifist here: http://www.charlessoft.com/
Download unpkg here: http://www.timdoug.com/unpkg/
Download AirPort Utility 5.6 here: http://support.apple.com/kb/DL1482
When the AirPort Utility .dmg file finishes downloading, open it to expand and reveal the AirPortUtility56.pkg package installer file.
Directions for Pacifist (I do not have screenshots for unpkg but the idea is similar):
Open Pacifist and from its File menu, navigate to the package and open it.
Click the "reveal triangles" until you see AirPort Utility 5.6.app:
Select it and then click Install from Pacifist's toolbar. It will then be installed in your Utilities folder, and you can quit Pacifist.
Mountain Lion will not allow you to delete its existing version of AirPort Utility. Just ignore it. It and the older version (which will bear the unique name "AirPort Utility 5.6") can peacefully coexist.
If you happen to have an archived copy of the AU 5.6 app somewhere, such as a Time Machine backup or equivalent, you can simply restore it or drag the app to your Mountain Lion system's Utilities folder instead of resorting to the above procedure. It will run without complaint. It is only the package installer that is the problem.
If you have an older computer with a version of AirPort Utility earlier than 6.0, you can administer it that way as well.

How to Connect Airport Express to Existing Wireless Network (Client Mode)

I am posting this for everyone tearing their hair out trying to connect the Airport Express to your own existing home wireless network. After spending 2 hours last night installing this on my father-in-law's home network, I hope to be able to save someone else the agony we went through.
So here's the situation:
Say you already have your own home network set up, and all you want is to be able to use AirTunes to play music off iTunes into your speaker system. And, you don't need the printer sharing capability nor creation of another wireless network (2 of the features of Airport Express). Then this solution is for you - read on.
Unfortunately, Apple's user manual is very unclear how to connect Airport Express to your own network. When you look at the picture diagram they provide, they show Airport Express picking up its signal from another Apple-oriented base. This can make you think you need to buy another piece of hardware to make it work. DON'T If you read through the manual, the Support section here, etc., you will hear lots of talk about "Client Mode" - and that this is the only way to get it to work. Nice - but no one really tells you how to set up the Airport in client mode.
Do yourself a favor, toss that user manual aside and run these steps.
(Note: These directions assume your DSL/Cable Modem is hooked up to a wireless router or acts as its own wireless router)
1. Get a cat5 Ethernet cable (anything but an orange cable - that's a crossover cable) like you would use to connect your PC to your router to pick up the Internet.
2. Connect the Ethernet cable to the router on one end, and to the Airport Express unit on the other end.
3. Plug in your Airport Express unit to the wall (this will not necessarily become its permanent location - you will be able to move it later). The light will glow solid Amber for about 30-45 seconds while it starts up, then blink Amber. At this point, the unit is ready to operate.
4. Install the CD to the PC where your iTunes music is stored. This should be painless. Once you open the program, it should detect the Airport unit.
5. At this point, the on-screen wizard will present you with your options, and walk you through the setup. This is much like the user manual describes - and you should be good to go form here forward.
Some pointers:
- When asked if you want to create a new network, join an existing network, or connect via Ethernet, choose the middle option for joining an existing network. You will need to know the name of your network, the password to connect to the network (if present), and the type of encryption used on the network (e.g. WEP, WPA, etc.). Side note, WPA is recommended, as it is a higher level of security than WEP. You will be able to configure the Airport Express unit to automatically login to your network.
- I would recommend, when creating a password for the Airport Express unit, use the same password as your network, to avoid confusion.
6. The very last step will ask you to save the settings to the Airport Express. Here's the kicker - when you save the settings, you are TRICKING the Airport Express into no longer acting as a network broadcaster, but instead being a "slave" to your own network. What do I mean? You will lose the connection from your PC to the Airport Express - an error message will pop up telling you the unit can no longer be found. While you might think you did something wrong, you actually were successful!
7. Unplug your Airport Express, and disconnect the Ethernet cable from your router and the Airport unit. This will no longer be needed.
8. Go to your desired location where you want to plug in your Airport Express unit. Before plugging it in, connect your Audio cable from the Airport Express to your audio receiver. Once that is connected, then plug in the Airport Express unit. The light will glow solid Amber for 30-45 seconds while it loads, and then will blink Amber for a brief period of time before turning solid GREEN. When this happens, you have successfully connected the Airport Express to your home network!
9. Go back to your PC with iTunes. Open the Airport software - you should now have a listing for your Airport Express unit in the upper left. Click on this, and the wizard will guide you through connecting - you will need the password you created for the unit. You only need to go through this wizard once, and when finished, the software will tell you that can now use iTunes with your Airport unit.
10. Open iTunes. On the lower right, you will see a dropdown for Speakers, and it should be defaulted to My Computer. Click on that drop-down, and you will see the name of your Airport unit. Click on that name, and now your music will broadcast to the Airport unit!
11. Play a song in iTunes. Go to your audio receiver, and connect it to the channel for your external connection to the Airport Express unit. You should hear your music from iTunes. CONGRATULATIONS! =)
I hope these instructions were helpful - I am happy to answer any questions, so feel free to contact me, *******************@*****.**.
<Edited by Moderator>

Thanks for the detailed directions. You are absolutely correct in stating that people should toss the user manual; it's pretty worthless. I have had a problem setting up my new Airport Express as I have described in an earlier post - http://discussions.apple.com/thread.jspa?threadID=1839873&tstart=45
One quick question - does using your setup process set the AE up as part of a distributed network where the AE is acting as a wireless router where it is extending the range of your network? Or, is it simply a wireless connection to your stereo for iTunes? I am interested in having both, since my AE will be at the other end of the house from the main wireless router.
Thanks

After the Airport update today, Airport Utility no longer sees my new Extreme or my 2 new Airport Express relay stations (same network); however, my internet is working and all Airports are green?

After the Airport update today, Airport Utility 6.0 no longer sees my new Extreme or my 2 new Airport Express relay stations (same network); however, my internet is working and all Airports are green? I'm running Lion on my iMac and updated when Airport Utility prompted me to do so a few hours ago. After applying the updates is when Airport Utility stopped seeing my routers. But they are working? Thoughts?

Did you remember to completely power cycle the entire network?
You would want to do this after any update or change to the network.
If you did not do this yet......things are out of sequence.
Power off everything on the network.....all devices.....power down order is not important
Wait a few minutes
Start the modem first and let it run a minute or two by itself
Start the next device connected to the modem the same way
Work your way out on the network starting each device about a minute apart
Check the network

Why does airport express force me 2go wired with my laptop-to-netgear setup

This is what I had and wanted to do: My laptop was connected wirelessly to my netgear router. i wanted to have airport express join my wireless network. after many many hours of trial and error, I've succeeded getting airport express to work with netgear. But, BUT, only if I plug an ethernet cable into my laptop to my netgear router. After getting Airport Express to wirelessly connect to my router, my windows wireless connection says windows can't connect because it failed to receive a signal or response from the router. when i force connect, it's signal strength is so low it doesn't work.
so what gives? i'm seeking a solution that will allow my to go wireless again between my laptop and my netgear router.
is it perhaps something to do with wireless channels? is the airport hogging all the space?
apple should be castigated for making it so difficult to get the Airport Express to work with third-party routers. don't sell something aimed at consumers if it takes conceivably an engineer's brain and hours of fiddling to make it work.
thanks in advance for your swift responses.

As to your first question: You should re-read my post, as I already said: the AX is connected wirelessly to the netgear router. But I'll be clearer:
This is what I had and wanted to do: My laptop was connected wirelessly to my netgear router. i wanted to have airport express join my wireless network. after many many hours of trial and error, I've succeeded getting airport express to wirelessly connect to netgear. But, BUT, only if I plug an ethernet cable into my laptop to my netgear router. After getting Airport Express to wirelessly connect to my router, my windows wireless connection says windows can't connect because it failed to receive a signal or response from the router. when i force connect, it's signal strength is so low it doesn't work.
As to your second request: I'm loath to publish my settings on this or any forum. Plus, I don't even know what you mean by "wireless pane" and "internet pane" settings. If you can explain the terms, plus convince me posting this data won't represent a security risk to me, maybe.
Finally: I don't want to set up a new wireless network, particularly because, according to Apple, with Airport Express, I don't have to. What's the point of advertising that this thing can "join an existing wireless network," particularly when it seems to have kicked off my laptop from said network?

Airport express connect to existing network problems

Hello everyone, my thanks in advance for any help you can provide. I know this issue has been raised in various forms both on this forum and elsewhere on the net, however no solution so far has worked for me.
I have been trying to add my airport express to my existing wireless network in order to extend wireless connectivity in my lounge room and provide airplay functionality to my stereo. Previously, with my last router and ISP i had the same setup working fine but now i cannot for the life of me get it working again.
I have BT infinty internet and am using a TPLink WR1043ND router in place of the home hub that BT supplies. My wireless internet connection is fully functionning and everything service-wise is fine.
I have tried to connect my airport express (n) to my network and all seems to go well but despite everything i try i always end up with an express with solid green light that is not recognised wirelessly by airport utility 6.0 or as an output option in itunes. If i connect the express to my MBP via ethernet i can access the express to configure manually but modifying the settings have thus far had no effect. The express is listed in the device list of the router menu and in the express settings has the correct ip issued via dhcp from router, as well as subnet mask and router address. Primary and secondary DNS have been copied from my router settings. Network mode is set to join existing network, correct wpa/wpa2 key is input, and airplay is enabled.
Despite all this seemingly being correct, when i disconnect ethernet connection betwein express and mbp - airport looses the express from ethernet connected devices (obvs) but when i select wifi connected devices it states no configured base stations can be found. The express remains listed in the dhcp client list of the router though and the express green light is there!
I have tried factory reset of the express a number of times and gone through the setup process and receive the same result. I have reset the modem, router, express and powered down the mac a number of times, still to be faced with same result.
I am at a loss and hope that you can help

Okay so i've fixed it....
Decided to bite the bullet and engage Apple support and although the agent i spoke to tried very hard he was as baffled as i was. In the end (after nearly an hour) i was put on to a support manager who simply told me that the Airport Express joining non-apple router hardware is just not supported. A very very disapointing cop out of an answer and a bit of a let down from Apple. So i expressed (no pun intended) my disatisfaction and left the conversation.
Determined not to be beaten i had one final go and lo and behold got it running. Problem was with the firmware on my router! After i updated to the very latest there now seems no problem with the Express.
It was an elementary mistake, i was trying so hard to fix the problem i forgot to check the basics!!!
Hope this helps anyone else who may be having the same difficulty

Airport express stopped extending the network

Hi all,
I have had working an Airport Extreme acting as a wifi base plus an Airport Express to extend the network for more than one year and could receive an excellent wifi coverage all over the appartment.
Recently, I decided to update my laptop OS version (an old Leopard) first to Snow Leopard and immediately after to Lion. After lots of software updates, at some point I begun receiving warnings to update the Extreme firmware. I did so and that same day I realized that the Express was not working as network extender any more. I further got frustrated to see that the latest Airport Utility didn't even "like" my Express and I had to downgrade to Airport Utility 5.6 in order to be able to configure the Express.
This was almost one month ago and I have spent many hours and tried all kind of combinations since then. For instance, I checked that the express was ok by creating with it a new network. This worked perfectly. I also reseted the Express to manufaturing defaults several times. I have even created a full new network from the beginning. Nothing works.
Both devices show green lights, but when I'm close to the Express, the BSSID I get is that of the Extreme, not the Express BSSID. I can see the Express in Airport Utility 6 but it is shown as connected to the Extreme with a dashed line.
I don't know what else to try. The worse thing is that even by buying a new Express I don't get any guarantee that the problem won't persist, since the network extension has worked perfectly in the past and doesn't work any more.
Any ideas are welcome.
Best,
Pedro.

I am starting to think that I have a non-functional device.
That is looking like a possibility.
Try a Factory Default Reset if you have not done so already.
Leave the Express powered off for 15-20 minutes
Hold in the reset button first, and keep holding it for an additional 9-10 seconds while you simultaneously plug the power back into the Express
Release the reset button after the hold period and allow a full minute for the Express to restart to a slow, blinking amber light
Try to configure the Express in the same room as the main router. Restart the main router before you try to configure the Express. If it works, then move it further away....but do not reset it....to see if it will connect and behave.
If you still cannot configure the Express after the Factory Default Reset, I think you have a defective Express.

I'm trying to activate my Airport Express to a wireless network powered by an Airport Extreme. I get an error message that says I need to Use Airport Utility 5.6. My system is currently running Airport Utility 6.1

'm trying to activate my Airport Express to a wireless network powered by an Airport Extreme. I get an error message that says I need to Use Airport Utility 5.6. My system is currently running Airport Utility 6.1

Is your AirPort Express an older 802.11g model? If so, you will need to install v5.6 if you are running OS X Lion or 5.6.1 if running OS X Leopard or Snow Leopard. Unfortunately, the iOS version of the AirPort Utility cannot administer these older base stations.

I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn't support this base station. Go to AirPort Service and Support for more information."

I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Any thoughts?

This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
To check and see if that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express.

Why my airport express dont find my network

Similar Messages

Maybe you are looking for